Search NASA⌕ Search

SEARCH · Search NASA

Results for “diffusion barriers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Alloyed coatings for dispersion strengthened alloys

Processing techniques were developed for applying several diffusion barriers to TD-Ni and TD-NiCr. Barrier coated specimens of both substrates were clad with Ni-Cr-Al and Fe-Cr-Al alloys and diffusion annealed in argon. Measurement of the aluminum distribution after annealing showed that, of the readily applicable diffusion barriers, a slurry applied tungsten barrier most effectively inhibited the diffusion of aluminum from the Ni-Cr-Al clad into the TD-alloy substrates. No barrier effectively limited interdiffusion of the Fe-Cr-Al clad with the substrates. A duplex process was then developed for applying Ni-Cr-Al coating compositions to the tungsten barrier coated substrates. A Ni-(16 to 32)Cr-3Si modifier was applied by slurry spraying and firing in vacuum, and was then aluminized by a fusion slurry process. Cyclic oxidation tests at 2300 F resulted in early coating failure due to inadequate edge coverage and areas of coating porosity. EMP analysis showed that oxidation had consumed 70 to 80 percent of the aluminum in the coating in less than 50 hours.

Wermuth, F. R.↗
DOE OSTI2025

First-principles elucidation of the effects of Al-doping on Li-ion diffusion in LiCoO 2

Al-doped garnet Li 7 La 3 Zr 2 O 12 solid-electrolyte and LiCoO 2 cathode are promising choices as catholyte materials in all solid-state Li batteries, however, interdiffusion of Al is commonly evident during high-temperature processing and electrochemical cycling. Furthermore, to address the impact of Al interdiffusion on Li + transport properties in LiCoO 2 , we carried out a systematic evaluation of Al doping on Li + diffusion barriers in LiCoO 2 using first-principles based methods. Following the monovacancy diffusion mechanism, Al-doping (primarily at the Co site) is found to improve Li diffusion kinetics in the LiCoO 2 lattice due to favorable CoO 6 octahedral distortion experienced at the transition states. However, when considering the previously established dominant divacancy diffusion mechanism, slower Li diffusion is generally expected. In addition, a broad variation of Li diffusion barriers is observed upon Al doping, which suggests the system may suffer from non-uniform Li incorporation and diffusion that adversely affects its rate capacity during cycling. In summary, this work highlights, for the rational design of catholyte of all solid-state batteries, special attention may need to be paid to address the potential impact of non-intentional doping induced during processing on the overall electrochemical performance of the catholyte.

Al-doped LiCoO2↗
NASA NTRS2002

Method for improving the performance of oxidizable ceramic materials in oxidizing environments

Improved adhesion of thermal barrier coatings to nonmetallic substrates using a dense layer of ceramic on an underlying nonmetallic substrate that includes at least one oxidizable component. The improved adhesion occurs because the application of the dense ceramic layer forms a diffusion barrier for oxygen. This diffusion barrier prevents the oxidizable component of the substrate from decomposing. The present invention applies ceramic by a process that deposits a relatively thick and dense ceramic layer on the underlying substrate. The formation of the dense layer of ceramic avoids the problem of void formation associated with ceramic formation by most prior art thermal decomposition processes. The formation of voids has been associated with premature spalling of thermal barrier layers and other protective layers applied to substrates.

Nagaraj, Bangalore A.↗
DOE OSTI2025

Harnessing nanoscale densification for controlling gas selectivity in flexible zeolitic imidazolate frameworks

Flexible metal-organic frameworks (MOFs) are promising for gas separation due to their molecular recognition capabilities. However, gate-opening behavior in certain flexible MOFs can reduce gas selectivity, enabling simultaneous adsorption of multiple gases. We introduce a binder-free, pressure-free densification process to enhance gas selectivity in flexible zeolitic imidazolate frameworks (ZIF-7 and ZIF-9) by optimizing nanoparticle packing. Unlike powders, the densified ZIF-7 and ZIF-9 retain rhombohedral crystal structures after solvent removal, confirmed via synchrotron powder X-ray diffraction. This process modifies adsorption behavior by introducing a diffusion barrier, enabling diffusivity-driven kinetic separation and enhanced CO2/hydrocarbon selectivity. At 0.5 bar, ZIF-7 mono shows 2×, 4×, and 9.5× higher CO 2 selectivity over C 2 H 2 , C 2 H 4 , and C 2 H 6 , respectively, versus ZIF-7 pwd . ZIF-9 mono similarly shows 6.5×, 3×, and 39× improvements over ZIF-9 pwd . Both monoliths outperform powders in ternary gas mixtures. This study provides a novel strategy to control gate opening and enhance gas selectivity in flexible MOFs for practical separation applications.

CO2/hydrocarbon separation↗
NASA NTRS1990

Healing of voids in the aluminum metallization of integrated circuit chips

The thermal stability of GaAs modulation-doped field effect transistors (MODFETs) is evaluated in order to identify failure mechanisms and validate the reliability of these devices. The transistors were exposed to thermal step-stress and characterized at ambient temperatures to indicate device reliability, especially that of the transistor ohmic contacts with and without molybdenum diffusion barriers. The devices without molybdenum exhibited important transconductance deterioration. MODFETs with molybdenum diffusion barriers were tolerant to temperatures above 300 C. This tolerance indicates that thermally activated failure mechanisms are slow at operational temperatures. Therefore, high-reliability MODFET-based circuits are possible.

Cuddihy, Edward F.↗
NASA NTRS1988

Reaction kinetics between fiber and matrix

Interdiffusion and interdiffusion controlled intermediate phase formation in metal matrix composites can be of interest for the prolonged application of these systems at high temperatures. Methods are discussed that address the kinetics of interdiffusion in systems that exhibit solid solution intermixing or the formation of a third intermediate phase at the fiber/matrix interface, or both. The tungsten fiber reinforced niobium and tungsten fiber reinforced superalloy systems are employed as model systems for experimentation and discussion. In an effort to impede interdiffusion, the concept of ion implanted diffusion barriers have been examined. Preliminary results on the feasibility and effectiveness of ion implanted diffusion barriers are presented.

Kopp, M. W.↗
NASA NTRS1981

Oxygen impurity effects at metal/silicide interfaces - Formation of silicon oxide and suboxides in the Ni/Si system

The effect of implanted oxygen impurities on the Ni/Ni2Si interface is investigated using X-ray photoelectron spectroscopy, He-4(+) backscattering and O(d, alpha)-16 N-14 nuclear reactions. Oxygen dosages corresponding to concentrations of 1, 2, and 3 atomic percent were implanted into Ni films evaporated on Si substrates. The oxygen, nickel, and silicon core lines were monitored as a function of time during in situ growth of the Ni silicide to determine the chemical nature of the diffusion barrier which forms in the presence of oxygen impurities. Analysis of the Ni, Si, and O core levels demonstrates that the formation of SiO2 is responsible for the Ni diffusion barrier rather than Ni oxide or mixed oxides, such as Ni2SiO4. It is determined that 2.2 x 10 to the 16th O/qu cm is sufficient to prevent Ni diffusion under UHV annealing conditions.

Grunthaner, P. J.↗
DOE OSTI2026

Temperature dependent interfacial microstructure in HIP-bonded Al6061/Zr joints

Pressing (HIP) at 450 °C and 560 °C under 103 MPa for 90 minutes to evaluate interfacial diffusion and microstructural evolution. Sound metallurgical bonding was achieved at both temperatures, with Zr serving as an effective diffusion barrier. Microstructural analysis revealed the the formation of a (Al,Si)3Zr intermetallic layer at the Al/Zr interface, whose thickness increased from ~100 nm at 450 °C to ~2100 nm at 560 °C, consistent with temperature-driven diffusion kinetics. The thin and continuous reaction layer observed at 450 °C indicates controlled interdiffusion and minimal reaction zone growth, favorable for maintaining interface stability and ductility. At 560 °C, enhanced atomic mobility led to pronounced intermetallic development, confirming diffusion-controlled growth behavior. These results provide valuable insights for optimizing Al/Zr interface design and diffusion barrier performance in advanced structural and energy systems.

Al/Zr interface↗
NASA NTRS1989

Tribological properties of ceramic/Ti3Al-Nb sliding couples for use as candidate seal materials to 700 deg C

Tribological properties of Ti3Al-Nb intermetallic disks sliding against alumina-boria-silicate fabric were ascertained in air at temperatures from 25 to 700 C. These materials are candidates for sliding seal applications for the National AeroSpace Plane. The tests were done using a pin on disk tribometer. Sliding was unidirectional at 0.27 m/sec under a nominal contact stress of 340 kPa. Gold sputter or ion plating deposited films were used to reduce friction and wear. Rhodium and palladium films were used beneath the gold lubricating films to prevent diffusion of the substrate into the gold at high temperature. The friction and wear of the unlubricated specimens was unacceptable. Friction coefficients were generally greater than 1.0. The ion plated gold films, when used with a rhodium diffusion barrier reduced friction by almost a factor of 2. Wear was also substantially reduced. The sputter deposited films were not adherent unless the substrate was sputter cleaned immediately prior to film deposition. Palladium did not function as a diffusion barrier.

Dellacorte, Christopher↗
NASA NTRS1990

Tribological properties of ceramic-(Ti3Al-Nb) sliding couples for use as candidate seal materials to 700 C

Tribological properties of Ti3Al-Nb intermetallic disks sliding against alumina-boria-silicate fabric were ascertained in air at temperatures from 25 to 700 C. These materials are candidates for sliding seal applications for the National AeroSpace Plane. The tests were done using a pin on disk tribometer. Sliding was unidirectional at 0.27 m/sec under a nominal contact stress of 340 kPa. Gold sputter or ion plating deposited films were used to reduce friction and wear. Rhodium and palladium films were used beneath the gold lubricating films to prevent diffusion of the substrate into the gold at high temperature. The friction and wear of the unlubricated specimens was unacceptable. Friction coefficients were generally greater than 1.0. The ion plated gold films, when used with a rhodium diffusion barrier reduced friction by almost a factor of 2. Wear was also substantially reduced. The sputter deposited films were not adherent unless the substrate was sputter cleaned immediately prior to film deposition. Palladium did not function as a diffusion barrier.

Dellacorte, Christhopher↗
DOE OSTI2026

Measurement of low energy characteristic X-rays emitted present in U-10Mo HALEU alloy fuel

Advance high density monolithic alloy HALEU fuels have been scanned with a silicon drift detector scanning system to measure low-energy characteristic X-rays emitted by uranium daughters, as well as zirconium present as a foil diffusion barrier. Four peaks were measured across the surfaces of three plates, and are consistent with other thorium and protactinium peaks present in depleted uranium samples that are induced by the decay of 235 U and 238 U. Of the four peaks detected, three are dominated by the decay of 235 U, and one peak at 15.70 keV covers two characteristic X-rays from the zirconium diffusion barrier (Kα 1 ) and from a 231 Th 15.62 keV X-ray induced by 235 U α-decay. The low energies of these lines suggest that they are mostly emitted from the fuel meat surface, and the poor counting statistics caused by strong self-attenuation make these data a poor candidate for 235 U/ 238 U ratio analysis. We suggest, then, that these X-rays could be used for passive measurement of variations in the cladding thickness of these fuels to complement manual thickness measurement methods.

HALEU↗
NASA NTRS1980

Preliminary study of a solar selective coating system using black cobalt oxide for high temperature solar collectors

Black cobalt oxide coatings (high solar absorptance layer) were deposited on thin layers of silver or gold (low emittance layer) which had been previously deposited on oxidized (diffusion barrier layer) stainless steel substrates. The reflectance properties of these coatings were measured at various thicknesses of cobalt for integrated values of the solar and infrared spectrum. The values of absorptance and emittance were calculated from the measured reflectance values, before and after exposure in air at 650 C for approximately 1000 hours. Absorptance and emittance were interdependent functions of the weight of cobalt oxide. Also, these cobalt oxide/noble metal/oxide diffusion barrier coatings have absorptances greater than 0.90 and emittances of approximately 0.20 even after about 1000 hours at 650 C.

Mcdonald, G.↗
DOE OSTI2025

Porosity, swelling, and composition evolution in high-burnup monolithic U-Mo fuel

The microstructural progression of very high-burnup (>8 × 10 21 fissions/cm 3 ) monolithic uranium-molybdenum (U-10wt.%Mo) was analyzed, providing crucial insights into the behavior of post-recrystallized nuclear fuel, where scant data exists. Three focused ion beam cuboids sourced from a fuel plate with varying local burnups of 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 were characterized. The porosity and composition of the samples were evaluated to characterize the evolution of the microstructure as a function of fission density and different locations on the fuel plate, while simultaneously isolating plate-specific parameters such as Zr diffusion barrier thickness, hot-isostatic-pressing conditions, enrichment, and reactor conditions. The porosity was segmented, and the three-dimensional distribution of the porosity was extrapolated from the two-dimensional segmentation. The composition was assessed and quantified using energy-dispersive X-ray spectroscopy areal mapping. The porosity fraction increased as a function of the burnup from 27.77±0.51, 35.12±1.54, and 37.71±0.44 % for 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 , respectively. When compared to literature, the porosity volume fraction plateaus at burnups greater than 6 × 10 21 fissions/cm 3 , while the pore size grows linearly as a function of fission density. The number of large pores increased in number density as a function of burnup, while the smallest pores (<0.3 µm) increased up to 9.05 × 10 21 fissions/cm 3 , followed by a decrease at 9.36 × 10 21 fissions/cm 3 . The delamination and cracking in the fuel plate propagated through an interconnected porosity sublayer identified ∼5 µm from the diffusion barrier. The local swelling of the specimens was within or near the prediction bounds of the Robinson-Williams model for local swelling. The fission products, strontium, barium, cerium, and cesium, precipitated into the pores, while neodymium accumulated adjacent to the pores. Furthermore, these findings have direct implications for the development of fuel performance codes and the accurate documentation of the microstructure evolution in high burnup U-Mo, thus enhancing the safety and efficiency of nuclear fuel usage.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1985

Dopant effect of yttrium and the growth and adherence of alumina on nickel-aluminum alloys

The atom superposition and electron delocalization molecular orbital theory and large cluster models have been employed to study cation vacancy diffusion in alpha-Al2O3 and the bonding of alpha-Al2O3 to nickel, aluminum, and yttrium surfaces. Al(3+) diffusion barriers in alpha-Al2O3 by the vacancy mechanism are in reasonable agreement with experiment. The barrier to Y(3+) diffusion is predicted to be much higher. Since addition of yttrium to transition metal alloys is known to reduce the growth rate and stress convolutions in protective alumina scales, this result suggests the rate-limiting step in scale growth is cation vacancy diffusion. This may partially explain the beneficial effect of yttrium dopants on scale adhesion. The theory also predicts a very strong bonding between alumina and yttrium at the surface of the alloy. This may also be important to the adhesion phenomenon. It is also found that aluminum and yttrium atoms bond very strongly to nickel because of charge transfer from their higher lying valence orbitals to the lower lying nickel s-d band.

Anderson, A. B.↗
NASA NTRSDate not supplied

Development of Multilayered Coatings for Nerva-Type Graphite Fuel Elements- An Overview

“Mid-passage corrosion” (MPC) was observed in NbC and ZrC-coated graphite (Gr)-based nuclear fuels during the NERVA/Rover programs. A new multilayered coating concept was proposed to solve this problem. The concept envisions designing a compliant multilayered coatings architecture to accommodate the thermal expansion mismatch strains between the ZrC outer coating and the Gr/(U,Zr)C fuel matrix. Additionally, the coating architecture uses diffusion barriers to minimize carbon diffusion from the substrate, and hydrogen diffusion from the flowing gas stream, into the multilayer coating. The present paper provides a brief overview of the development of multilayered coatings deposited on Gr disks, as well as within the inner channels of a19-hole hexagonal rod 152.4 mm long, by chemical vapor deposition (CVD) in proof-of concept studies. The cross-sectional microstructural observations are discussed. These trials have established that it is possible to deposit multilayered coatings by CVD in 19-hole hexagonal rods similar to the NERVA fuel rod design although the quality of the coatings and the uniformity of their thicknesses require further improvement.

Multilayer coatings, graphite, nuclear thermal pro↗
NASA NTRS1992

Lightweight Protective Coatings For Titanium Alloys

Lightweight coating developed to protect titanium and titanium aluminide alloys and titanium-matrix composite materials from attack by environment when used at high temperatures. Applied by sol-gel methods, and thickness less than 5 micrometers. Reaction-barrier and self-healing diffusion-barrier layers combine to protect titanium alloy against chemical attack by oxygen and nitrogen at high temperatures with very promising results. Can be extended to protection of other environmentally sensitive materials.

Wiedemann, Karl E.↗
NASA NTRS2021

Microstructural Observations on Advanced Multilayer Protective Coatings for Nuclear Thermal Propulsion

The present research discusses the microstructures of a new multilayered coating concept proposed to solve the “midrange corrosion” problem observed in NbC and ZrC-coated graphite (Gr) nuclear fuels during the NERVA/Rover programs. The concept envisions designing a compliant multilayered coatings architecture to accommodate the thermal expansion mismatch strains between the ZrC outer coating and the Gr/(U,Zr)C fuel matrix along with using a diffusion barrier to minimize carbon and hydrogen diffusion, respectively. Multilayered coatings were deposited on Gr substrates by chemical vapor deposition (CVD). Graphite disks, as well as the inner channels of a 19-hole hexagonal rod 152.4 mm long, were coated by CVD in proof-of concept process demonstration studies. Coated disk specimens were thermally-cycled between ambient and 1900 K for as long as 20 cycles with a 1h hold time at the temperature using both stepped and non-interrupted thermal cycling methods. Detailed cross-sectional microstructural analyses were conducted on the thermally-cycled coated disks. These results showed that the coatings were intact after 20 thermal cycles at 1900 K although the bonding of the overlay Mo coating appeared to be influenced by the oxygen content in the layer. Seven transverse sections were cut along the length from the coated hexagonal rod for microstructural studies. All the nineteen channels were observed to have been coated in all the sections. This paper reports the results of detailed microstructural analyses, compositional line scans and x-ray dot maps conducted on three coated channels from a mid-section of the rod. The measured values of carbon (C) were observed to be exceptionally high in all the specimens, which were attributed to hydrocarbon contamination of the specimen surfaces. It was observed that the oxygen (O) levels were high in all the coating layers even after approximately correcting for the observed high values of C. The source of O contamination of the CVD reactor system was attributed to either the presence of oxychloride impurities in the precursor salts or a pin hole leak in the coating system. It is concluded that high values of O result in poor bonding of the Mo overlay to the ZrC layer. These trials have established that it is possible to deposit multilayered coatings by CVD in 19-hole hexagonal rods 152.4 mm long similar to the NERVA fuel rod design although the quality of the coatings and the uniformity of their thicknesses require further improvement.

Nuclear thermal propulsion, multilayer coatings, m↗
DOE OSTI2025

First-Principles Studies of Tritium Species Diffusivity Across the Interfaces of Ni-NiZr Alloy-Zircaloy-4

A tritium producing assembly, also known as tritium producing burnable absorber rods (TPBARs), consists of a metal getter tube located between the cladding and γ-LiAlO2 pellets. The metal getter tube is composed of a nickel (Ni) layer coated on Zircaloy-4. The getter assembly is used to capture tritium (3H) species (mainly 3H2 and 3H2O) generated from γ-LiAlO2 pellets during irradiation. Exploring 3H species (3H2, 3H2O) dissociation on the Ni surface and diffusion in the Ni layer and across the interface of Ni-plated Zircaloy-4 getters can provide insights on tritium transport and retention in the pellets and the getter materials. . In FY25, based on the ideal interface model of Ni-Zircaloy-4 generated in FY24, we will further explore the diffusion pathways of 3H across such Ni-ZrNi-alloy layer-Zircalory-4 interfaces under different conditions, including with oxide/hydroxide clusters on the Ni layer, and impurities located in ZrNi-alloy and Zircalory-4 layers. Due to the size limitation of DFT simulation, we will separate the 3-layer system into 3 sub-systems: Ni-ZrNi interface, ZrNi alloy layer, ZrNi-alloy-Zircaloy-4 interface, and simulate the diffusion barriers for tritium.

diffusion barrier↗