Results for “efficient routes” — Page 3

NASA NTRS1991

Environmental constraints imposed on High-Speed Civil Transport (HSCT) designs

This paper assesses airframe and engine technologies in terms of the preliminary environmental design goals for the HSCT. The preliminary goals are: (1) no adverse change in stratospheric ozone concentration caused by engine emissions; (2) meet FAR Stage 3 noise limits and operate within airport community noise exposure guidelines; and (3) minimize the environmental impact of overland sonic booms. The effects of design Mach number, low-emission combustors, engine fuel efficiency, and route structure are primary parameters affecting stratospheric emission effects. To minimize community noise, the engine cycle/noise suppression devices and high-lift devices must be developed, and operational procedures must be developed. To minimize the sonic boom impact, cruise weight, aircraft length, cruise altitude, and aircraft shape are the prime parameters to be considered. The detrimental effects of environmental constraints on aircraft operational costs are evaluated through tradeoff studies.

Mortlock, Alan↗

NASA NTRS1993

Layout and cabling considerations for a large communications antenna array

Layout considerations for a large deep space communications antenna array are discussed. A fractal geometry for the antenna layout is described that provides optimal packing of antenna elements, efficient cable routing, and logical division of the array into identical sub-arrays.

Logan, R. T., Jr.↗

NASA NTRS2012

A Concept for Airborne Precision Spacing for Dependent Parallel Approaches

The Airborne Precision Spacing concept of operations has been previously developed to support the precise delivery of aircraft landing successively on the same runway. The high-precision and consistent delivery of inter-aircraft spacing allows for increased runway throughput and the use of energy-efficient arrivals routes such as Continuous Descent Arrivals and Optimized Profile Descents. This paper describes an extension to the Airborne Precision Spacing concept to enable dependent parallel approach operations where the spacing aircraft must manage their in-trail spacing from a leading aircraft on approach to the same runway and spacing from an aircraft on approach to a parallel runway. Functionality for supporting automation is discussed as well as procedures for pilots and controllers. An analysis is performed to identify the required information and a new ADS-B report is proposed to support these information needs. Finally, several scenarios are described in detail.

Barmore, Bryan E.↗

NASA NTRS2016

Airspace Technology Demonstration 3 (ATD-3): Applied Traffic Flow Management Project Overview

No abstract available

applied traffic flow management↗

NASA NTRS2003

Evaluation of a Dispatcher's Route Optimization Decision Aid to Avoid Aviation Weather Hazards

This document describes the results and analysis of the formal evaluation plan for the Honeywell software tool developed under the NASA AWIN (Aviation Weather Information) 'Weather Avoidance using Route Optimization as a Decision Aid' project. The software tool aims to provide airline dispatchers with a decision aid for selecting optimal routes that avoid weather and other hazards. This evaluation compares and contrasts route selection performance with the AWIN tool to that of subjects using a more traditional dispatcher environment. The evaluation assesses gains in safety, in fuel efficiency of planned routes, and in time efficiency in the pre-flight dispatch process through the use of the AWIN decision aid. In addition, we are interested in how this AWIN tool affects constructs that can be related to performance. The construct of Situation Awareness (SA), workload, trust in an information system, and operator acceptance are assessed using established scales, where these exist, as well as through the evaluation of questionnaire responses and subject comments. The intention of the experiment is to set up a simulated operations area for the dispatchers to work in. They will be given scenarios in which they are presented with stored company routes for a particular city-pair and aircraft type. A diverse set of external weather information sources is represented by a stand-alone display (MOCK), containing the actual historical weather data typically used by dispatchers. There is also the possibility of presenting selected weather data on the route visualization tool. The company routes have not been modified to avoid the weather except in the case of one additional route generated by the Honeywell prototype flight planning system. The dispatcher will be required to choose the most appropriate and efficient flight plan route in the displayed weather conditions. The route may be modified manually or may be chosen from those automatically displayed.

Dorneich, Michael C.↗

NASA NTRS1990

A description and evaluation of TIMER: A time-based terminal flow-control concept

A description of a time-based ATC concept called TIMER (Traffic Intelligence for the Management of Efficient Runway-scheduling) and the results of a fast time and real time computer evaluation are presented. The concept was designed to improve the efficiency of extended terminal area operations (en route approach, transition, and terminal flight to the runway). TIMER integrates en route metering, fuel efficient cruise and profile descents, terminal sequencing and spacing together with computer-generated controller aids, in order to fully use runway capacity and improve efficiency of delay absorption. The concept, by using simplified aircraft models, accommodates both 4-D and non 4-D equipped aircraft and is designed for integration into the manual, voice linked ATC system in an evolutionary manner and still be able to accommodate proposed system upgrade features such as data link and further ground automation. Fast time and real time computer simulation results identify and show the effects and interactions of such key variables as horizon of control, metering fix and final approach delivery time errors, aircraft separation requirements, delay discounting, wind, flight technical error, and knowledge of aircraft final approach speed. The current ATC system has a runway interarrival-error standard deviation of approx. 26 seconds. Simulation results indicate that, with computer aiding, the runway interarrival-error standard deviation for non 4-D equipped traffic can be reduced to the region of 8 to 12 seconds if expected final approach speed is known; however, the reduction is only in the region of 16 to 20 seconds if expected final approach speed is unknown. Another major finding is that en route metering fix delivery-error standard deviation should be kept to less than a number somewhere between 35 to 45 seconds to achieve full runway capacity. This requirement implies the need for either airborne automation or assistance to the controller since the current manual performance in today's en route metering environment is in the order of 1.5 minutes.

Credeur, Leonard↗

NASA NTRS2017

Subject Matter Expert Evaluation of Multi-Flight Common Route Advisories

Traffic flow management seeks to balance the demand for National Airspace System (NAS) flight resources, such as airspace and airports, with the available supply. When forecasted weather blocks nominal air traffic routes, traffic managers must re-route affected flights for weather avoidance. Depending on the nature and scope of the weather, traffic managers may use pre-coordinated re-routes such as Playbook Routes or Coded Departure Routes, or may design ad hoc local re-routes. The routes of affected flights are modified accordingly. These weather avoidance routes will, of course, be less efficient than the nominal routes due to increased flight time and fuel burn. In current traffic management operations, the transition into a weather avoidance re-routing initiative is typically implemented more aggressively than the transition out of that initiative after the weather has dissipated or moved away. For example, strategic large-scale Playbook re-routes are sometimes left in place (as initially implemented) for many hours before being lifted entirely when the weather dissipates. There is an opportunity to periodically modify the re-routing plan as weather evolves, thereby attenuating its adverse impact on flight time and fuel consumption; this is called delay recovery. Multi-Flight Common Routes (MFCR) is a NASA-developed operational concept and associated decision support tool for delay recovery, designed to assist traffic managers to efficiently update weather avoidance traffic routes after the original re-routes have become stale due to subsequent evolution of the convective weather system. MFCR groups multiple flights to reduce the number of advisories that the traffic manager needs to evaluate, and also merges these flights on a common route segment to provide an orderly flow of re-routed traffic. The advisory is presented to the appropriate traffic manager who evaluates it and has the option to modify it using MFCRs graphical user interface. If the traffic manager finds the advisory to be operationally appropriate, he or she would coordinate with the Area Supervisor(s) of the sectors that currently control the flights in the advisory. When the traffic manager accepts the MFCR advisory via the user interface, the corresponding flight plan amendments would be sent to the displays of the appropriate sector controllers, using the Airborne Re-Routing (ABRR) capability which is scheduled for nationwide operation in 2017. The sector controllers would then offer this time-saving route modification to the pilots of the affected flights via datalink (or voice), and implement the corresponding flight plan amendment if the pilots accept it. MFCR is implemented as an application in the software environment of the Future Air traffic management Concepts Evaluation Tool (FACET). This paper focuses on an initial subject matter expert (SME) evaluation of MFCR. The evaluation covers MFCRs operational concept, algorithm, and user interface.

Human-in-the-loop Evaluation↗

NASA NTRS2017

Subject Matter Expert Evaluation of Multi-Flight Common Route Advisories

Traffic flow management seeks to balance the demand for National Airspace System (NAS) flight resources, such as airspace and airports, with the available supply. When forecasted weather blocks nominal air traffic routes, traffic managers must re-route affected flights for weather avoidance. Depending on the nature and scope of the weather, traffic managers may use pre-coordinated re-routes such as Playbook Routes or Coded Departure Routes, or may design ad hoc local re-routes. The routes of affected flights are modified accordingly. These weather avoidance routes will, of course, be less efficient than the nominal routes due to increased flight time and fuel burn. In current traffic management operations, the transition into a weather avoidance re-routing initiative is typically implemented more aggressively than the transition out of that initiative after the weather has dissipated or moved away. For example, strategic large-scale Playbook re-routes are sometimes left in place (as initially implemented) for many hours before being lifted entirely when the weather dissipates. There is an opportunity to periodically modify the re-routing plan as weather evolves, thereby attenuating its adverse impact on flight time and fuel consumption; this is called delay recovery. Multi-Flight Common Routes (MFCR) is a NASA-developed operational concept and associated decision support tool for delay recovery, designed to assist traffic managers to efficiently update weather avoidance traffic routes after the original re-routes have become stale due to subsequent evolution of the convective weather system. MFCR groups multiple flights to reduce the number of advisories that the traffic manager needs to evaluate, and also merges these flights on a common route segment to provide an orderly flow of re-routed traffic. The advisory is presented to the appropriate traffic manager who evaluates it and has the option to modify it using MFCRs graphical user interface. If the traffic manager finds the advisory to be operationally appropriate, he or she would coordinate with the Area Supervisor(s) of the sectors that currently control the flights in the advisory. When the traffic manager accepts the MFCR advisory via the user interface, the corresponding flight plan amendments would be sent to the displays of the appropriate sector controllers, using the Airborne Re-Routing (ABRR) capability which is scheduled for nationwide operation in 2017. The sector controllers would then offer this time-saving route modification to the pilots of the affected flights via datalink (or voice), and implement the corresponding flight plan amendment if the pilots accept it. MFCR is implemented as an application in the software environment of the Future Air traffic management Concepts Evaluation Tool (FACET). This paper focuses on an initial subject matter expert (SME) evaluation of MFCR. The evaluation covers MFCRs operational concept, algorithm, and user interface.

Traffic flow management↗

NASA NTRS2010

A Mixed Integer Linear Program for Solving a Multiple Route Taxi Scheduling Problem

Aircraft movements on taxiways at busy airports often create bottlenecks. This paper introduces a mixed integer linear program to solve a Multiple Route Aircraft Taxi Scheduling Problem. The outputs of the model are in the form of optimal taxi schedules, which include routing decisions for taxiing aircraft. The model extends an existing single route formulation to include routing decisions. An efficient comparison framework compares the multi-route formulation and the single route formulation. The multi-route model is exercised for east side airport surface traffic at Dallas/Fort Worth International Airport to determine if any arrival taxi time savings can be achieved by allowing arrivals to have two taxi routes: a route that crosses an active departure runway and a perimeter route that avoids the crossing. Results indicate that the multi-route formulation yields reduced arrival taxi times over the single route formulation only when a perimeter taxiway is used. In conditions where the departure aircraft are given an optimal and fixed takeoff sequence, accumulative arrival taxi time savings in the multi-route formulation can be as high as 3.6 hours more than the single route formulation. If the departure sequence is not optimal, the multi-route formulation results in less taxi time savings made over the single route formulation, but the average arrival taxi time is significantly decreased.

Montoya, Justin Vincent↗

NASA NTRS2017

Efficient Planning of Wind-Optimal Routes in North Atlantic Oceanic Airspace

The North Atlantic oceanic airspace (NAT) is crossed daily by more than a thousand flights, which are greatly affected by strong jet stream air currents. Several studies devoted to generating wind-optimal (WO) aircraft trajectories in the NAT demonstrated great efficiency of such an approach for individual flights. However, because of the large separation norms imposed in the NAT, previously proposed WO trajectories induce a large number of potential conflicts. Much work has been done on strategic conflict detection and resolution (CDR) in the NAT. The work presented here extends previous methods and attempts to take advantage of the NAT traffic structure to simplify the problem and improve the results of CDR. Four approaches are studied in this work: 1) subdividing the existing CDR problem into sub-problems of smaller sizes, which are easier to handle; 2) more efficient data reorganization within the considered time period; 3) problem localization, i.e. concentrating the resolution effort in the most conflicted regions; 4) applying CDR to the pre-tactical decision horizon (a couple of hours in advance). Obtained results show that these methods efficiently resolve potential conflicts at the strategic and pre-tactical levels by keeping the resulting trajectories close to the initial WO ones.

Rodionova, Olga↗

NASA NTRS2014

Aircraft Trajectory Design Based on Reducing the Combined Effects of Carbon-Dioxide, Oxides of Nitrogen and Contrails

Aircraft operations need to meet the combined requirements of safety, efficiency, capacity and reduced environmental impact. Aircraft routes can be made efficient by flying wind optimal routes. However, the desire to reduce the impact of aviation emissions and contrails may result in trajectories, which deviate from wind optimal trajectories leading to extra fuel use. The lifetime associated with different emissions and contrails varies from a few hours to several hundred years. The impact of certain gases depends on the amount and location of the emission, and the decision-making horizon, in years, when the impact is estimated. The Absolute Global Temperature Potential (AGTP) is used as a metric to measure the combined effects of emissions and contrails. This paper extends earlier work by the authors to include the effect of oxides of nitrogen in the development of aircraft trajectories to reduce the combined effects of carbon dioxide, oxides of nitrogen (NOX) and contrails. The methodology is applied to air traffic in the continental US. The paper shows the trade-offs between reducing emissions and the cost of extra fuel using a fuel sensitivity index, defined as the reduction in AGTP per kg of fuel. The paper shows the performance of the optimization strategy for decision intervals of 10, 25 and 100 years. Based on the simplified models, the inclusion of NOX emissions has a slight influence on the minimal climate impact trajectories when the decision horizons are around 25 years.

air trafic optimization↗

NASA NTRS2014

Aircraft Trajectory Design Based on Reducing the Combined Effects of Carbon-di-oxide, Nitrogen and Contrails

Aircraft operations need to meet the combined requirements of safety, efficiency, capacity and reduced environmental impact. Aircraft routes can be made efficient by flying wind optimal routes. However, the desire to reduce the impact of aviation emissions and contrails may result in trajectories, which deviate from wind optimal trajectories leading to extra fuel use. The lifetime associated with different emissions and contrails varies from a few hours to several hundred years. The impact of certain gases depends on the amount and location of the emission, and the decision-making horizon, in years, when the impact is estimated. The Absolute Global Temperature Potential (AGTP) is used as a metric to measure the combined effects of emissions and contrails. This paper extends earlier work by the authors to include the effect of oxides of nitrogen in the development of aircraft trajectories to reduce the combined effects of carbon dioxide, oxides of nitrogen (NOX) and contrails. The methodology is applied to air traffic in the continental US. The paper shows the trade-offs between reducing emissions and the cost of extra fuel using a fuel sensitivity index, defined as the reduction in AGTP per kg of fuel. The paper shows the performance of the optimization strategy for decision intervals of 10, 25 and 100 years. Based on the simplified models, the inclusion of NOX emissions has a slight influence on the minimal climate impact trajectories when the decision horizons are around 25 years.

Sridhar, Banavar↗

NASA NTRS2004

A Practical Approach to Obstacle Field Route Planning for Unmanned Rotorcraft

Autonomous helicopter operations in the near-earth environment will require robust and efficient obstacle field route planning. A method for obstacle field route planning is presented, which is composed of a mesh generation phase, a graph search phase, and a route refinement phase. The method mixes optimization and heuristics to obtain a satisfactory solution quickly. Simulations based on an unmanned helicopter model are presented.

Howlet, Jason K.↗

NASA NTRS2019

ATD-3 Dynamic Routes for Arrivals in Weather (DRAW) Operational Concept, V2.0

NASA's Airspace Technology Demonstration-3 (ATD-3) is the applied traffic flow management activity, and third in the series of ATD projects. ATD-3 provides a suite of en route automation tools, both ground and flight-deck based, that focus on improving the efficiency of en route operation from initial cruise to arrival into the Terminal Radar Approach Control (TRACON). Dynamic Routes for Arrivals in Weather (DRAW) is a technology in the ATD-3 suite that is designed to provide Traffic Managers with a capability to efficiently manage arrival traffic flow and help sustain metering operations when weather is impacting arrivals into major airports. DRAW mitigates convective weather impact on arrival metering operations by providing tools to Traffic Managers that enable efficient reroutes free of convective weather conflicts, and integrated with the arrival metering schedule(s).

terminal airspace↗

NASA NTRS2000

User's Guide for Computer Program that Routes Signal Traces

This disk contains both a FORTRAN computer program and the corresponding user's guide that facilitates both its incorporation into your system and its utility. The computer program represents an efficient algorithm that routes signal traces on layers of a printed circuit with both through-pins and surface mounts. The computer program included is an implementation of the ideas presented in the theoretical paper titled "A Formal Algorithm for Routing Signal Traces on a Printed Circuit Board", NASA TP-3639 published in 1996. The computer program in the "connects" file can be read with a FORTRAN compiler and readily integrated into software unique to each particular environment where it might be used.

Hedgley, David R., Jr.↗

NASA NTRS2004

Masked Proportional Routing

Masked proportional routing is an improved procedure for choosing links between adjacent nodes of a network for the purpose of transporting an entity from a source node ("A") to a destination node ("B"). The entity could be, for example, a physical object to be shipped, in which case the nodes would represent waypoints and the links would represent roads or other paths between waypoints. For another example, the entity could be a message or packet of data to be transmitted from A to B, in which case the nodes could be computer-controlled switching stations and the links could be communication channels between the stations. In yet another example, an entity could represent a workpiece while links and nodes could represent, respectively, manufacturing processes and stages in the progress of the workpiece towards a finished product. More generally, the nodes could represent states of an entity and the links could represent allowed transitions of the entity. The purpose of masked proportional routing and of related prior routing procedures is to schedule transitions of entities from their initial states ("A") to their final states ("B") in such a manner as to minimize a cost or to attain some other measure of optimality or efficiency. Masked proportional routing follows a distributed (in the sense of decentralized) approach to probabilistically or deterministically choosing the links. It was developed to satisfy a need for a routing procedure that 1. Does not always choose the same link(s), even for two instances characterized by identical estimated values of associated cost functions; 2. Enables a graceful transition from one set of links to another set of links as the circumstances of operation of the network change over time; 3. Is preferably amenable to separate optimization of different portions of the network; 4. Is preferably usable in a network in which some of the routing decisions are made by one or more other procedure(s); 5. Preferably does not cause an entity to visit the same node twice; and 6. Preferably can be modified so that separate entities moving from A to B do not arrive out of order.

Wolpert, David↗

NASA NTRS2017

Current Safety Nets Within the U.S. National Airspace System

There are over 70,000 flights managed per day in the National Airspace System, with approximately 7,000 aircraft in the air over the United States at any given time. Operators of each of these flights would prefer to fly a user-defined “4D” trajectory (4DT), which includes arrival and departure times; preferred gates and runways at the airport; efficient, wind-optimal routes for departure, cruise and arrival phase of flight; and fuel efficient altitude profiles. To demonstrate the magnitude of this achievement a single flight from Los Angeles to Baltimore, accesses over 35 shared or “constrained” resources that are managed by roughly 30 air traffic controllers (at towers, approach control and en route sectors); along with traffic managers at 12 facilities, using over 22 different, independent automation system (including TBFM, ERAM, STARS, ASDE-X, FSM, TSD, GPWS, TCAS, etc.). In addition, dispatchers, ramp controllers and others utilize even more systems to manage each flight’s access to operator-managed resources. Flying an ideal 4DT requires successful coordination of all flight constraints among all flights, facilities, operators, pilots and controllers. Additionally, when conditions in the NAS change, the trajectories of one or more aircraft may need to be revised to avoid loss of flight efficiency, predictability, separation or system throughput. The Aviation Safety Network has released the 2016 airliner accident statistics showing a very low total of 19 fatal airliner accidents, resulting in 325 fatalities1. Despite several high profile accidents, the year 2016 turned out to be a very safe year for commercial aviation, Aviation Safety Network data show. Over the year 2016 the Aviation Safety Network recorded a total of 19 fatal airliner accidents [1], resulting in 325 fatalities. This makes 2016 the second safest year ever, both by number of fatal accidents as well as in terms of fatalities. In 2015 ASN recorded 16 accidents while in 2013 a total of 265 lives were lost. How can we keep it that way and not upset the apple cart by premature insertion of innovative technologies, functions, and procedures? In aviation, safety nets function as the last system defense against incidents and accidents. Current ground-based and airborne safety nets are well established and development to make them more efficient and reliable continues. Additionally, future air traffic control safety nets may emerge from new operational concepts.

Smith, Brian E.↗

NASA NTRS2023

Ames Contrail Simulation Model: Modeling Aviation Induced Contrails and the Computation of Contrail Radiative Forcing Using Air Traffic Data

NASA is developing traffic flow management strategies to reduce the impact of aviation on climate and improve efficiency of aircraft routes in the presence of limited airport and airspace capacity constraints, which are partly due to convective weather and natural calamities. Development of Strategic Traffic Flow Management (STFM) requires models of aircraft emissions and contrails, and models of their effect on climate. There is extensive literature on the modeling of contrails and the Radiative Forcing (RF) associated with contrails. This report captures the latest NASA developments in this research area and describes the integrated modeling, analysis, and software development to support STFM. Aircraft contrails are long, thin and often linear clouds triggered by aircraft engine exhausts in the high-altitude ice-saturated atmosphere. Contrails, similar to that of natural cirrus clouds, can impact global climate by reflecting shortwave radiation and trapping longwave radiation. Recent studies from the Intergovernmental Panel on Climate Change (IPCC) have shown that aircraft contrails are estimated to have greater impact on global warming than aircraft CO 2 emissions. The Ames Contrail Simulation Model (ACSM) presented in this report simulates the full life cycle of aircraft contrails, including their formation, dynamic evolution, and dissipation, and calculates the associated RF with actual meteorological and air traffic data. ACSM combines models from previous studies that focus on contrail formation and persistence based on the Schmidt-Appleman theoretical criteria, and it incorporates elements of cloud dynamics, microphysics, and climate modeling found in other surveyed contrail models, while also making adjustment for improved computational efficiency. In addition, ACSM is integrated with NASA's state-of-the-art flight simulation software for rapid assessment of aircraft contrail impacts. Applications include assessments of long-term global climate impact resulting from aviation-induced contrails and the design of optimal contrail-mitigation aircraft operation strategies.

aviation contrails↗