SEARCH · Search NASA
Results for “elastoplasticity”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Poromechanical cohesive interface element with combined Mode I-II cohesive zone elastoplasticity for simulating fracture in fluid-saturated porous media
A combined Mode I-II cohesive zone (CZ) elasto-plastic constitutive model, and a two-dimensional (2D) cohesive interface element (CIE) are formulated and implemented at small strain within an ABAQUS User Element (UEL) for simulating 2D crack nucleation and propagation in fluid-saturated porous media. Here, the CZ model mitigates problems of convergence for the global Newton-Raphson solver within ABAQUS, which when combined with a viscous stabilization procedure allows for simulation of post-peak response under load control for coupled poromechanical finite element analysis, such as concrete gravity dam stability analysis. Verification examples are presented, along with a more complex ambient limestone-concrete wedge fracture experiment, water-pressurized concrete wedge experiment, and concrete gravity dam stability analyses. A calibration procedure for estimating the CZ parameters is demonstrated with the limestone-concrete wedge fracture process. For the water-pressurized concrete wedge fracture experiment it is shown that the inherent time-dependence of the poromechanical CIE analysis provides a good match with experimental force versus displacement results at various crack mouth opening rates, yet misses the pore water pressure evolution ahead of the crack tip propagation. This is likely a result of the concrete being partially-saturated in the experiment, whereas the finite element analysis assumes fully water saturated concrete. For the concrete gravity dam analysis, it is shown that base crack opening and associated water uplift pressure leads to a reduced Factor of Safety, which is confirmed by separate analytical calculations.
Elastoplastic transition in a metastable β-Titanium alloy, Timetal-18 – An in-situ synchrotron X-ray diffraction study
Not Available
Hyper-elastoplastic/damage modeling of rock with application to porous limestone
Not Available
Numerical methods and improvements for simulating quasi-static elastoplastic materials
Not Available
Site response analysis: Uncertain motions propagating through uncertain elastoplastic soil
Not Available
Rafting and elastoplastic deformation of superalloys studied by neutron diffraction
The rafting of monocrystalline Ni- and Co-based superalloys has been studied by neutron diffractometry. Lattice parameter misfit values and the difference in phase stiffnesses at room temperature, 650 °C, and 900 °C are presented. These microstructural parameters should assist in refining computer models that aim to predict precipitate evolution in superalloys and aid future alloy design. The nature of rafting is shown experimentally to be dependent upon the lattice parameter misfit. The 900 °C yield strength of the γ-phase of the Co-based superalloy with a rafted microstructure occurs at ~100 MPa, when loaded at a low strain rate.
Determination of Sticking Probability Based on the Critical Velocity Derived from a Visco-Elastoplastic Model to Characterize Ash Deposition in an Entrained Flow Gasifier
Explore the source record for details and available documents.
Wide-range simulation of elastoplastic wave fronts and failure of solids under high-speed loading
The aim of this paper is numerical study of deformation processes and failure of vanadium under shock-wave loading. According developed statistical theory of solid with mesoscopic defects the constitutive equations were proposed in terms of two structural variables characterizing behavior of defects ensembles: defect density tensor and structural scaling parameter. On the basis of wide-range constitutive equations the mathematical model of deformation behavior and failure of vanadium was developed taking into account the bond relaxation mechanisms, multistage of fracture and nonlinearity kinetic of defects. Results of numerical simulation allow the description of the major effects of shock wave propagation (elastic precursor decay, grow of spall strength under grow strain rate)
Utilizing integrated neutron diffraction and elastoplastic self-consistent crystal plasticity model to quantitatively assess the strengthening mechanism in Al–12.5Ce and Al–12.5Ce–0.4Mg alloys
An integrated in-situ neutron diffraction and elastic plastic self-consistent crystal plasticity (EPSC-CP) modeling scheme is performed on a binary Al–12Ce alloy and a ternary Al–12Ce–0.4Mg alloys. Using this scheme, the constitutive parameters, i.e. elastic constants and slip system parameters of individual phases can be calibrated which can be used in microstructure-based CP models to predict materials performance. From this study, it is shown that the elastic constants of Al 11 Ce 3 intermetallics calculated from density function theory calculation in the literature are rather accurate. When applied to the EPSC-CP model, the lattice strains of both the binary and ternary alloys are correctly predicted as compared with experiments, and large lattice strain differences between Al (100) plane and Al 11 Ce 3 (010) plane are demonstrated. The slip system parameters calibrated by the scheme shows that the addition of 0.4 wt% Mg in the alloy has little influence on the critical resolved shear stress of initial dislocation glide in the Al matrix which caused plastic yield in the material. This can be explained by the very dilute Mg solute content in the Al solid solution, causing large spacing of Al–Mg lattice misfit sites and little impact on resistance of dislocation glide at initial yield. The 0.4 wt% Mg addition, on the other hand, has a large influence on the hardening term in the slip system parameters, indicating those Al–Mg misfit sites do help dislocation accumulation during the deformation. The impact of dilute Mg addition on the Al slip system parameters is also reflected in the flow behavior of the ternary alloy: little impact on the yield stress, but a large impact on working hardening and tensile strength of the materials which is consistent with the literature.
Dynamic Model of Elastoplastic Normal Collision of Spherical Particles under Nonlocal Plasticity
The problem of normal collision of a spherical particle with a half-space is considered with allowance for nonlocal plastic deformation in the case where the strength limit depends on the contact radius, as well as for the strengthening effect in the deformed material. The dimensionless coefficient of normal velocity restitution has been calculated numerically as a function of the initial velocity of the spherical particle. The obtained data coincide well with experimental results available in the literature.
Effect of Electrochemical Charging on Elastoplastic Properties and Fracture Toughness of Li X CoO 2
Mechanical degradation of lithium-ion battery (LIB) electrodes has been correlated with capacity fade and impedance growth over repeated charging and discharging. Knowledge of how the mechanical properties of materials used in LIBs are affected by electrochemical lithiation and delithiation could provide insight into design choices that mitigate mechanical damage and extend device lifetime. Here, we measured Young's modulus E, hardness H, and fracture toughness K Ic via instrumented nanoindentation of the prototypical intercalation cathode, Li X CoO 2 , after varying durations of electrochemical charging. After a single charge cycle, E and H decreased by up to 60%, while K Ic decreased by up to 70%. Microstructural characterization using optical microscopy, Raman spectroscopy, X-ray diffraction, and further nanoindentation showed that this degradation in K Ic was attributable to Li depletion at the material surface and was also correlated with extensive microfracture at grain boundaries. These results indicate that K Ic reduction and irreversible microstructural damage occur during the first cycle of lithium deintercalation from polycrystalline aggregates of Li X CoO 2 , potentially facilitating further crack growth over repeated cycling. Such marked reduction in K Ic over a single charge cycle also yields important implications for the design of electrochemical shock-resistant cathode materials.
An elastoplastic finite element study of cylindrical plane-strain contact for steel/steel and Inconel 617/Incoloy 800H undergoing unidirectional sliding
The current work employs a two-dimensional plane strain finite element analysis to investigate the unidirectional sliding contact between a deformable half-cylinder and a deformable flat block. The unidirectional sliding is governed by a displacement-controlled action where the materials of the two contacting bodies are first set to identical steels at 20 ℃ and then to Inconel 617 and Incoloy 800H at 800 ℃. First, a normal interference (indentation) is applied, which is followed by unidirectional sliding. The von Mises stress distribution, plastic strain distribution, junction growth, normal force, tangential force, effective coefficient of friction, and scars on the surface of the block are obtained during the sliding motion. The leading edge of the contacting area and the bulk material under the leading edge experience large von Mises stresses. The large plastic strain is found on the surface of the block, and forms a “pocket” shape under the surface. The junction growth is also investigated, showing the direction of the growth is in the same direction of the tangential force that the weaker material experiences. The forces and the effective coefficient of friction are found to stabilize after a certain sliding distance, and the effective coefficient of friction converges to the coefficient of friction used in the model. Pileup is found on the surface of the block after a sufficient unidirectional sliding distance.
General formulation of a poromechancial cohesive surface element with elastoplasticity for modeling interfaces in fluid-saturated geomaterials
Explore the source record for details and available documents.
Gas Flow Tightly Coupled to Elastoplastic Geomechanics for Tight- and Shale-Gas Reservoirs: Material Failure and Enhanced Permeability
We investigate coupled flow and geomechanics in gas production from extremely low permeability reservoirs such as tight and shale gas reservoirs, using dynamic porosity and permeability during numerical simulation. In particular, we take the intrinsic permeability as a step function of the status of material failure, and the permeability is updated every time step. We consider gas reservoirs with the vertical and horizontal primary fractures, employing the single and dynamic double porosity (dual continuum) models. We modify the multiple porosity constitutive relations for modeling the double porous continua for flow and geomechanics. The numerical results indicate that production of gas causes redistribution of the effective stress fields, increasing the effective shear stress and resulting in plasticity. Shear failure occurs not only near the fracture tips but also away from the primary fractures, which indicates generation of secondary fractures. These secondary fractures increase the permeability significantly, and change the flow pattern, which in turn causes a change in distribution of geomechanical variables. From various numerical tests, we find that shear failure is enhanced by a large pressure drop at the production well, high Biot's coefficient, low frictional and dilation angles. Smaller spacing between the horizontal wells also contributes to faster secondary fracturing. When the dynamic double porosity model is used, we observe a faster evolution of the enhanced permeability areas than that obtained from the single porosity model, mainly due to a higher permeability of the fractures in the double porosity model. These complicated physics for stress sensitive reservoirs cannot properly be captured by the uncoupled or flow-only simulation, and thus tightly coupled flow and geomechanical models are highly recommended to accurately describe the reservoir behavior during gas production in tight and shale gas reservoirs and to smartly design production scenarios.