Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrical conversion efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Large reduction of thermal conductivity leading to enhanced thermoelectric performance in p-type Mg 3 Bi 2 –YbMg 2 Bi 2 solid solutions

Intensifying the phonon scattering via point defect engineering has been demonstrated to be particularly effective in minimizing the lattice thermal conductivity for enhancing thermoelectric performance. In this work, significant phonon scattering has been realized by alloying YbMg 2 Bi 2 with Mg 3 Bi 2 . The substantial mass difference between the host atom Yb and the alloying atom Mg leads to an intense phonon scattering effect that significantly reduces the lattice thermal conductivity. The room-temperature lattice thermal conductivity decreases from ~2.7 W m -1 K -1 for YbMg 2 Bi 1.96 to ~0.8 W m -1 K -1 for Yb 0.7 Mg 0.3 Mg 2 Bi 1.96 , a reduction of ~70%. Benefiting from the greatly reduced thermal conductivity, the average ZT has been effectively improved from ~0.46 for YbMg 2 Bi 1.96 to ~0.61 for Yb 0.8 Mg 0.2 Mg 2 Bi 1.96 , an enhancement of ~33%. In addition, the predicted maximum heat-to-electricity conversion efficiency can be increased from ~7% for YbMg 2 Bi 1.96 to ~10% for Yb 0.8 Mg 0.2 Mg 2 Bi 1.96 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Novel Gas-Driven Fuel Cell HVAC and Dehumidification Prototype

Performance of a novel gas-driven, electricity-producing heating, ventilation, and air conditioning (HVAC) system with no vapor compression and no hydrofluorocarbon (HFC) refrigerant shall be discussed in the paper. The prototype was evaluated at ORNL under a Small Business Voucher (SBV) Cooperative Research and Development (CRADA) program. The target market is commercial buildings in the United States. The goal is to mitigate or eliminate grid-power for building air conditioning, coincident peak demand and associated spinning reserves, aiding in flattening of the “duck curve”. The technical goal is to transform the common packaged rooftop unit into a cost-effective distributed energy resource, opening a new range of small applications and broad markets for micro-combined cycle cooling, heating, and power with integral thermal energy storage. The test results indicate the prototype would be competitive with natural gas distributed power plants with average electrical production ranging from 45% to 60% natural gas to electricity conversion efficiency. The technology has a Primary Energy Savings Potential of 4.4 Quads, higher than any other air conditioning and heating technology.

Betts, Daniel↗
DOE OSTI2026

Evaluating Lithium-Lead Mixtures for Increased Tritium Breeding in Fusion Energy Blanket Systems: Exploring the Impact of Composition and Temperature

This project investigates hypo- and hyper-eutectic liquid lithium-lead (PbLi) mixtures as a coolant in fusion blanket systems, with a focus on testing the compatibility of compositions with better tritium breeding ratios (TBR). The 12-month study concentrates on static corrosion experiments, comparing silicon carbide (SiC) corrosion rates in Li-rich and eutectic Li-Pb mixtures, and examining interactions between Mo and PbLi. The research seeks to determine the maximum operating temperatures for this material combination, acknowledging the balance between Li-Pb melting temperature and achievable TBR to unlock new opportunities for blanket design. This work lays the groundwork for future collaboration between Kyoto Fusioneering and Oak Ridge National Laboratory (ORNL). Findings could enhance the TBR of fusion blanket designs, and impact fusion energy development by confirming material compatibility between different Li-Pb mixtures with SiC and Mo at higher temperatures, including at temperatures relevant for very high-temperature blankets (1,000 °C), which could enable higher electricity conversion efficiencies and commercial applications using process heat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1976

Comparative performance of solar thermal power generation concepts

A performance comparison is made between the central receiver system (power tower) and a distributed system using either dishes or troughs and lines to transport fluids to the power station. These systems were analyzed at a rated capacity of 30 MW of thermal energy delivered in the form of superheated steam at 538 C (1000 F) and 68 atm (1000 psia), using consistent weather data, collector surface waviness, pointing error, and electric conversion efficiency. The comparisons include technical considerations for component requirements, land utilization, and annual thermal energy collection rates. The relative merits of different representative systems are dependent upon the overall conversion as expressed in the form of performance factors in this paper. These factors are essentially indices of the relative performance effectiveness for different concepts based upon unit collector area. These performance factors enable further economic tradeoff studies of systems to be made by comparing them with projected production costs for these systems.

Wen, L.↗
NASA NTRS1978

Experiments with enhanced mode thermionic converters

Reduction of the ionization and scattering losses associated with ignited mode cesium diodes is essential for high thermal-to-electrical conversion efficiency. Use of an auxiliary electrode in conjunction with a noble gas in the interelectrode space should permit more efficient ion generation for space charge neutralization. The characeristics of a thermionic triode utilizing a ring electrode and a dispenser cathode emitter have been studied as a function of xenon pressure, cesium reservoir temperature, spacing, electrode temperature and pulse parameters (i.e., potential, duration and repetition rate) applied to the auxiliary electrode. Pulsed operation significantly enhanced output power with uniform discharges appearing to be sustained at emitter-collector spacings as low as 0.5 mm.

Oettinger, P. E.↗
NASA NTRS1980

Titanium dioxide antireflection coating for silicon solar cells by spray deposition

A high-speed production process is described for depositing a single-layer, quarter-wavelength thick antireflection coating of titanium dioxide on metal-patterned single-crystal silicon solar cells for terrestrial applications. Controlled atomization spraying of an organotitanium solution was selected as the most cost-effective method of film deposition using commercial automated equipment. The optimal composition consists of titanium isopropoxide as the titanium source, n-butyl acetate as the diluent solvent, sec-butanol as the leveling agent, and 2-ethyl-1-hexanol to render the material uniformly depositable. Application of the process to the coating of circular, large-diameter solar cells with either screen-printed silver metallization or with vacuum-evaporated Ti/Pd/Ag metallization showed increases of over 40% in the electrical conversion efficiency. Optical characteristics, corrosion resistance, and several other important properties of the spray-deposited film are reported. Experimental evidence indicates a wide tolerance in the coating thickness upon the overall efficiency of the cell. Considerations pertaining to the optimization of AR coatings in general are discussed, and a comprehensive critical survey of the literature is presented.

Kern, W.↗
NASA NTRS1992

Laser-beam power for lunar and space applications

Photovoltaic properties of GaAlAs/GaAs heteroface converters were measured using a 0.81-micron diode laser. Results indicate that the converters under consideration are promising devices for converting diode-laser radiation to electricity. Conversion efficiency as high as 45 percent has been obtained using GaAs devices, while Si converters of the SSF type give efficiencies up to 34.2 percent.

Walker, Gilbert H.↗
NASA NTRS1992

Laser-beam power for lunar and space applications

GaAlAs/GaAs heteroface converters were experimentally tested using DIRECT laser irradiation of photovoltaic devices. It is concluded that the two types of converters are promising for converting diode-laser radiation to electricity. Conversion efficiency as high as 45 and 34.2 percent was obtained using GaAS and Si converters of the SSF type, respectively.

Walker, Gilbert H.↗
NASA NTRS1999

Electrolysis Propulsion Provides High-Performance, Inexpensive, Clean Spacecraft Propulsion

An electrolysis propulsion system consumes electrical energy to decompose water into hydrogen and oxygen. These gases are stored in separate tanks and used when needed in gaseous bipropellant thrusters for spacecraft propulsion. The propellant and combustion products are clean and nontoxic. As a result, costs associated with testing, handling, and launching can be an order of magnitude lower than for conventional propulsion systems, making electrolysis a cost-effective alternative to state-of-the-art systems. The electrical conversion efficiency is high (>85 percent), and maximum thrust-to-power ratios of 0.2 newtons per kilowatt (N/kW), a 370-sec specific impulse, can be obtained. A further advantage of the water rocket is its dual-mode potential. For relatively high thrust applications, the system can be used as a bipropellant engine. For low thrust levels and/or small impulse bit requirements, cold gas oxygen can be used alone. An added innovation is that the same hardware, with modest modifications, can be converted into an energy-storage and power-generation fuel cell, reducing the spacecraft power and propulsion system weight by an order of magnitude.

deGroot, Wim A.↗
NASA NTRS2007

Coating Thermoelectric Devices To Suppress Sublimation

A technique for suppressing sublimation of key elements from skutterudite compounds in advanced thermoelectric devices has been demonstrated. The essence of the technique is to cover what would otherwise be the exposed skutterudite surface of such a device with a thin, continuous film of a chemically and physically compatible metal. Although similar to other sublimation-suppression techniques, this technique has been specifically tailored for application to skutterudite antimonides. The primary cause of deterioration of most thermoelectric materials is thermal decomposition or sublimation - one or more elements sublime from the hot side of a thermoelectric couple, changing the stoichiometry of the device. Examples of elements that sublime from their respective thermoelectric materials are Ge from SiGe, Te from Pb/Te, and now Sb from skutterudite antimonides. The skutterudite antimonides of primary interest are CoSb3 [electron-donor (n) type] and CeFe(3-x)Co(x)Sb12 [electron-acceptor (p) type]. When these compounds are subjected to typical operating conditions [temperature of 700 C and pressure <10(exp -5) torr (0.0013 Pa)], Sb sublimes from their surfaces, with the result that Sb depletion layers form and advance toward their interiors. As the depletion layer advances in a given device, the change in stoichiometry diminishes the thermal-to-electric conversion efficiency of the device. The problem, then, is to prevent sublimation, or at least reduce it to an acceptably low level. In preparation for an experiment on suppression of sublimation, a specimen of CoSb3 was tightly wrapped in a foil of niobium, which was selected for its chemical stability. In the experiment, the wrapped specimen was heated to a temperature of 700 C in a vacuum of residual pressure <10(exp -5) torr (0.0013 Pa), then cooled and sectioned. Examination of the sectioned specimen revealed that no depletion layer had formed, indicating the niobium foil prevented sublimation of antimony at 700 C. This was a considerable improvement, considering that uncoated CoSb3 had been found to decompose to form the lowest antimonide at the surface at only 600 C. Evidently, because the mean free path of Sb at the given temperature and pressure was of the order of tens of centimeters, any barrier closer than tens of centimeters (as was the niobium foil) would have suppressed transport of Sb vapor, thereby suppressing sublimation of Sb

Sakamoto, Jeffrey↗
DOE OSTI2023

Characterization of Fe-6Si Soft Magnetic Alloy Produced by Laser-Directed Energy Deposition Additive Manufacturing

Abstract Commercial electrical steels, Fe-Si alloys with < 4 wt.% Si, are inexpensive and efficient materials for electrical power conversion. Further efficiency improvements require increasing the silicon concentration to 6 wt.%, at which point the material becomes brittle and difficult to form by conventional rolling and sheet fabrication methods. Additive manufacturing stands to overcome challenges with commercial manufacturing techniques by leveraging near-net-shape fabrication. The wide array of process conditions provides additive manufacturing with increased flexibility, enabling control over the microstructure and mechanical properties. This work explores the microstructures and magnetic properties of ring-shaped Fe-Si alloys produced using concentric and cross-hatch tool paths on a laser-directed energy deposition additive manufacturing system. Concentric-built samples exhibit elongated grain structures while cross-hatch-built samples comprise lower aspect ratio grain structures. Thermal finite element analysis simulations model the stress conditions produced by the different scan path geometries. Microhardness measurements probe the mechanical properties as a function of anneal temperature, providing a qualitative understanding of the intergranular defect density. Soft magnetic properties measured under quasistatic and AC conditions show frequency- and microstructure-dependent coercivity and permeability. Finally, analysis of the core loss quantifies how the build strategies and thermal treatments influence efficiency in electrical power conversion applications. Understanding the influences of scan path geometry and thermal treatment provides a pathway towards application of additively manufactured soft magnetic materials.

Adamczyk, Jesse M.↗
DOE OSTI2021

Investigating anode off-gas under spark-ignition combustion for SOFC-ICE hybrid systems

Solid oxide fuel cell – internal combustion engine (SOFC-ICE) hybrid systems are an attractive solution for electricity generation. The system can achieve up to 70% theoretical electric power conversion efficiency through energy cascading enabled by utilizing the anode off-gas from the SOFC as the fuel source for the ICE. Experimental investigations were conducted with a single cylinder Cooperative Fuel Research (CFR) engine by altering fuel-air equivalence ratio (φ), and compression ratio (CR) to study the engine load, combustion characteristics, and emissions levels of dry SOFC anode off-gas consisting of 33.9% H 2 , 15.6% CO, and 50.5% CO 2 . The combustion efficiency of the anode off-gas was directly evaluated by measuring the engine-out CO emissions. The highest net-indicated fuel conversion efficiency of 31.3% occurred at φ = 0.90 and CR = 13:1. These results demonstrate that the anode off-gas can be successfully oxidized using a spark ignition combustion mode. The fuel conversion efficiency of the anode tail gas is expected to further increase in a more modern engine architecture that can achieve increased burn rates in comparison to the CFR engine. NO x emissions from the combustion of anode off-gas were minimal as the cylinder peak temperatures never exceeded 1800 K. This experimental study ultimately demonstrates the viability of an ICE to operate using an anode off-gas, thus creating a complementary role for an ICE to be paired with a SOFC in a hybrid power generation plant.

Engineering↗
DOE OSTI2023

Efficient Hydraulic-to-electric Energy Conversion for PCM-based Ocean Thermal Gradient Energy System to Power Uncrewed Underwater Vehicles

Since the 2000, there have been numerous investigations into electrical energy storage types that use ocean thermal-to-electricity conversion techniques. Field tests have demonstrated that this technology is feasible for UUVs with long-term missions of over 3,000 km per deployment. Nonetheless, the energy generated by this method is not sufficient to meet the energy requirements of Unscrewed Underwater Vehicles (UUVs). The objective of this study is to design a highly effective ocean thermal gradient energy system to support long-term missions of a UUV. To enhance the performance of the thermal gradient energy system, we have developed a hybrid type (buoyancy regulation and electrical storage). Phase Change Material (PCM)-based energy harvesting system to facilitate efficient UUV operations. A prototype of the hydraulic-to-electric conversion system was implemented, and experimental findings indicate that the hybrid system successfully delivers hydraulic energy for buoyancy change and improved efficiency of hydraulic-to-electric energy conversion, demonstrating its potential as a promising technology for supporting long-term UUV missions.

Deng, Zhiqun↗
NASA NTRS2000

A New High Efficiency Segmented Thermoelectric Unicouple

To achieve high thermal-to-electric energy conversion efficiency, it is desirable to operate thermoelectric generator devices over large temperature gradients and also to maximize the thermoelectric performance of the materials used to build the devices. However, no single thermoelectric material is suitable for use over a very wide range of temperatures (approx. 300 - 1000 K). It is therefore necessary to use different materials in each temperature range where they possess optimum performance. This can be achieved in two ways: 1) multistage thermoelectric generators where each stage operates over a fixed temperature difference and is electrically insulated but thermally in contact with the other stages and 2) segmented generators where the p- and n-legs are formed of different segments joined in series. The concept of integrating new thermoelectric materials developed at the Jet Propulsion Laboratory (JPL) into a segmented thermoelectric generator has been presented in detail in earlier publications . This new generator is expected to operate over a 300-973 K temperature difference and will use novel segmented legs based on a combination of state-of-the-art thermoelectric materials and novel p-type Zn4Sb3, p-type CeFe4Sb12-based alloys and n-type CoSb3-based alloys. An increase in the conversion efficiency of about 60% is expected compared to conventional Bi2Te3- and PbTe-based generators. We present in this paper the latest experimental results from the bonding studies between the different segments of the p-legs, n-legs, and p-leg to n-leg interconnect. Evaluation of the bond quality was done by measuring the contact resistance across the joints as well as by detailed microstructure investigations to reveal any potential interdiffusion. Among the materials investigated as inter-layers between the different segments of the legs, Pd-Ag joining alloys have been found to provide mechanically stable and low electrical resistance bonds.

Caillat, T.↗
NASA NTRS1976

Status of photoelectrochemical production of hydrogen and electrical energy

The efficiency for conversion of electromagnetic energy to chemical and electrical energy utilizing semiconductor single crystals as photoanodes in electrochemical cells was investigated. Efficiencies as high as 20 percent were achieved for the conversion of 330 nm radiation to chemical energy in the form of hydrogen by the photoelectrolysis of water in a SrTiO3 based cell. The SrTiO3 photoanodes were shown to be stable in 9.5 M NaOH solutions for periods up to 48 hours. Efficiencies of 9 percent were measured for the conversion of broadband visible radiation to hydrogen using n-type GaAs crystals as photoanodes. Crystals of GaAs coated with 500 nm of gold, silver, or tin for surface passivation show no significant change in efficiency. By suppressing the production of hydrogen in a CdSe-based photogalvanic cell, an efficiency of 9 percent was obtained in conversion of 633 nm light to electrical energy. A CdS-based photogalvanic cell produced a conversion efficiency of 5 percent for 500 nm radiation.

Byvik, C. E.↗
NASA NTRS1999

A New High Efficiency Segmented Thermoelectric Unicouple

To achieve high thermal-to-electric energy conversion efficiency, it is desirable to operate thermoelectric geneteor devices over large temperature gradients and also to maximize the thermoelectric performance of the materials used to build the devices.

Energy↗
DOE OSTI2018

Tandem luminescent solar concentrators based on engineered quantum dots

Luminescent solar concentrators (LSCs) can serve as large-area sunlight collectors for terrestrial and space-based photovoltaics. Due to their high emission efficiencies and readily tunable emission and absorption spectra, colloidal quantum dots have emerged as a new and promising type of LSC fluorophore. Spectral tunability of the quantum dots also facilitates the realization of stacked multilayered LSCs, where enhanced performance is obtained through spectral splitting of incident sunlight, as in multijunction photovoltaics. Here, we demonstrate a large-area (>230 cm 2 ) tandem LSC based on two types of nearly reabsorption-free quantum dots spectrally tuned for optimal solar-spectrum splitting. This prototype device exhibits a high optical quantum efficiency of 6.4% for sunlight illumination and solar-to-electrical power conversion efficiency of 3.1%. In conclusion, the efficiency gains due to the tandem architecture over single-layer devices quickly increase with increasing LSC size and can reach more than 100% in structures with window sizes of more than 2,500 cm 2 .

14 SOLAR ENERGY↗