SEARCH · Search NASA
Results for “electrode preparation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
High power density performance of WPt and WRh electrodes in the alkali metal thermoelectric converter
The properties of the alkali metal thermoelectric converter (AMTEC) are discussed together with those of an efficient AMTEC electrode. Three groups of electrodes were prepared and tested for their performance as AMTEC electrodes, including WPt-T3, WRh-B1, and WRh-B2. The best electrodes of both WPt and WRh types typically exhibited low porosity, and thickness greater than 0.8 micron, which indicated that transport in these electrodes does not occur by a purely free-molecular flow mode. The observed values of the exchange current were found to be within the range of those observed for oxide-free Mo electrodes under similar conditions.
Space Suit Electrocardiographic Electrode Selection: Are commercial electrodes better than the old Apollo technology?
The NASA Manned Space Program uses an electrocardiograph (ECG) system to monitor astronauts during extravehicular activity (EVA). This ECG system, called the Operational Bioinstrumentation System (OBS), was developed during the Apollo era. Throughout the Shuttle program these electrodes experienced failures during several EVAs performed from the Space Shuttle and International Space Station (ISS) airlocks. An attempt during Shuttle Flight STS-109 to replace the old electrodes with new commercial off-the-shelf (COTS) disposable electrodes proved unsuccessful. One assumption for failure of the STS-109 COTS electrodes was the expansion of trapped gases under the foam electrode pad, causing the electrode to be displaced from the skin. Given that our current electrodes provide insufficient reliability, a number of COTS ECG electrodes were tested at the NASA Altitude Manned Chamber Test Facility. Methods: OBS disposable electrodes were tested on human test subjects in an altitude chamber simulating an Extravehicular Mobility Unit (EMU) operating pressure of 4.3 psia with the following goals: (1) to confirm the root cause of the flight certified, disposable electrode failure during flight STS-109. (2) to identify an adequate COTS replacement electrode and determine if further modifications to the electrodes are required. (3) to evaluate the adhesion of each disposable electrode without preparation of the skin with isopropyl alcohol. Results: There were several electrodes that failed the pressure testing at 4.3psia, including the electrodes used during flight STS-109. Two electrodes functioned well throughout all testing and were selected for further testing in an EMU at altitude. A vent hole placed in all electrodes was also tested as a possible solution to prevent gas expansion from causing electrode failures. Conclusions: Two failure modes were identified: (1) foam-based porous electrodes entrapped air bubbles under the pad (2) poor adhesion caused some electrodes to fail
Synthesis and Modification of Holey Graphene for Energy Storage
Porous graphene materials have recently drawn significant interest for energy storage applications due to the effective use of the graphitic surface area provided by the pores. Holey graphene is a type of porous graphene with pores in the form of physical through thickness holes. This type of porous graphene provides a unique morphology that allows for effective transport of molecular species through the graphene plane. Therefore, as we recently demonstrated, holey graphene could be advantageous in the preparation of electrodes in supercapacitors with high volumetric performance.1 We have developed methodologies to scalably prepare holey graphene materials with or without the use of catalysts (Figure 1).1,2 In this presentation, we will discuss the choice of synthetic strategies and experimental conditions on the morphology and physical properties of holey graphene (Figure 2) and the effect on their electrochemical properties. We will also present the results on the further modification of holey graphene to study their physical and chemical properties, especially with regard to the stability and chemical reactivity of carbons located around the edges of the holes.
Fabrication and testing of large size nickel-zinc cells
The design and construction of nickel zinc cells, containing sintered nickel electrodes and asbestos coated inorganic separator materials, were outlined. Negative electrodes were prepared by a dry pressing process while various inter-separators were utilized on the positive electrodes, consisting of non-woven nylon, non-woven polypropylene, and asbestos.
Unraveling the Effects of Hierarchical Bimodal Microscale Porosity on Thick Electrodes
The thick electrode design is preferential in high-energy lithium-ion batteries (LIBs) systems. However, the sluggish ionic transport in homogeneous porous thick electrodes severely limits the areal capacity at high charging/discharging rates. The hierarchical porous design is a promising approach to mitigate kinetic limitations because it can distribute mass effectively in natural systems. In this study, the effects of bimodal microscale pores are fully investigated in thick electrodes from both architectural and electrochemical perspectives. Notably, by introduction of the bimodal microscale porous structure, the rate capability improves remarkably in thick electrodes with a low porosity (39%). Herein, by combining experimental results with simulations, this work presents a rational design guideline for preparing thick electrodes with a porosity at the commercial level, as well as simultaneous high energy and power densities, which brings new insights into the advanced electrode architecture design in scalable high-energy and high-power energy storage systems for practical applications.
Pre-Sodiated Ti3C2Tx MXene Structure and Behavior as Electrode for Sodium-Ion Capacitors
Explore the source record for details and available documents.
An Investigation of the Electrochemical Activity of (Ba/Sr)FeO 3-y Anodes
FeO x , SrFeO 3-y (SF), and Ba 0.5 Sr 0.5 FeO 3–y (BSF) were studied for application as fuel oxidation catalysts in solid oxide fuel cells (SOFC) anodes. Electrodes were prepared by impregnation into porous yttria-stabilized zirconia (YSZ), with La 0.3 Sr 0.7 TiO 3–y (LST) added for electronic conductivity. The electrode impedances decreased dramatically upon addition of SF and BSF and much less when only SrO or FeO x were added. Temperature Programmed Desorption (TPD) of O 2 from oxidized BSF showed O 2 desorbing between 200 °C and 700 °C, while no O 2 desorbed from Fe 2 O 3 below 900 °C. The results, together with thermodynamic analysis, suggest that stabilization of Fe +4 in the perovskite lattice plays an important role in enhancing the catalytic activity of SF and BSF by providing access to a Fe 3+ /Fe 4+ redox couple that can accept oxygen anions from the yttria-stabilized zirconia (YSZ) electrolyte. Oxygen is weakly bound to these sites facilitating its reaction with adsorbed H 2 .
Manufacturing Cathodes via Dry-Processing for Lithium-Ion Batteries
Conventional lithium-ion battery (LIB) electrodes are prepared through a wet slurry process with n-methyl pyrrolidone solvent, especially for cathodes. The wet slurry process encounters several disadvantages such as binder migration, electrode cracking in thick electrodes, energy intense heat-dry NMP solvent removal, and costly NMP recovery. The cost and energy consumption of coating and drying of electrode are about 11.5 % and > 46 % in LIB manufacturing, respectively. Thereby, it is essential to develop a facile roll-to-roll solvent-free LIB electrode processing for reducing the cost and energy consumption. Recently, the Maxwell-type dry processing (DP) shines new lights on LIB manufacturing, which mainly bases on dry mixing (DM) of electrode component powder followed by calendering into electrode films and laminating onto current collectors, realizing the rapid manufacturing of LIB electrodes in a powder-to-film manner for industries. This report shares some recent progress on the DP from our group. We aim to further advance the manufacturing science of DP by correlating the processing conditions with electrode properties and performance. Particularly, we investigate the effect of DM, and compression on the polytetrafluoroethylene (PTFE) binder fiberization, porosity, mechanical properties, electrical conductivity and electrochemical behaviors of electrodes. The DM study suggests that PTFE fiberization heavily relies on the degree of DM. Insufficient DM results in poor PTFE fiberization while outrageous DM damages the formed PTFE fibers. Both negatively affect the mechanical behaviors of the electrodes and their rate capability. However, moderate DM is highly beneficial. In addition, our study of the porosity impact reveals that LiNi0.8Mn0.1Co0.1O2 (NMC) secondary particles can be broken into primary particles due to compression, especially at low porosity. Those fractured NMC secondary particles exhibit lower modulus. We propose that a moderate porosity of around 32% favors the electronic conductivity, charge transfer impedance and rate capability. The study of the cathodic electrolyte interphase layer of PTFE-based DPed electrode confirms that side reactions of PTFE binder due to the formation of LiF in LiClO4-based electrolyte.
Performance of advanced chromium electrodes for the NASA Redox Energy Storage System
Chromium electrodes were prepared for the NASA Redox Storage System with meet the performance requirements for solar-photovoltaic, wind-turbine and electric utility applications. Gold-lead catalyzed carbon felt electrodes up tp 930 sq cm were fabricated and tested in single cells and multicell stacks for hydrogen evolution, coulombic efficiency, catalyst stability and electrochemical activity. Factors which affect the overall performance of a particular electrode include the carbon felt lot, the cleaning treatment and the gold catalyzation method. Effects of the chromium solution chemistry and impurities on charge/discharge performance are also presented.
Fabrication and testing of negative-limited sealed nickel-cadmium cells
The design, construction, and testing of 100,20Ah and 100,3Ah negative-limited sealed cells are reported. The required physical dimensions of the hardware and components necessary to produce 20 and 3 Ah cells were established. The stainless steel cans and covers have been ordered. The covers contain two ceramic seals. The fabrication of electrodes was started. About 55% (879 electrodes) of the required cadmium electrodes has been prepared. About 44% of the porous nickel substrates (plaques) required for the preparation of the nickel oxide electrodes has been completed.
Characterizing Dynamic Structure in Battery Electrodes by Time-Resolved Cryo-TEM
In recent years, cryogenic transmission electron microscopy (cryo-TEM) has enabled high-resolution characterization of sensitive battery materials by minimizing electron beam-induced artifacts and damage. Success of this technique relies on the preparation of thin, rapidly frozen samples, generally by disassembling batteries under inert atmosphere, transferring materials of interest to a TEM grid, and finally plunge freezing into a cryogen. In material degradation studies, this extensive time between electrochemical cycling and cryo-TEM characterization leaves room for structural relaxation, diffusion, and other dynamic processes that make it difficult to precisely correlate the imaged structure with the native structure that evolves during battery cycling or aging. Here, we present a method to integrate battery cycling with fast preparation of electrode samples for cryo-TEM. This enables higher fidelity between the structures characterized and the electrochemical state of interest, which we use to study deformation in silicon nanoparticle anodes for lithium-ion batteries.
Vapor-deposited platinum as a fuel-cell catalyst
Electrodes are prepared by vacuum deposition of platinum on nickel substrate with conventional vapor-deposition apparatus. Amount of platinum loaded on substrate can be veried by changing exposure time during deposition. These electrodes are significantly more effective than conventional oxygen electrodes.
Accurate pointing of tungsten welding electrodes
Thoriated-tungsten is pointed accurately and quickly by using sodium nitrite. Point produced is smooth and no effort is necessary to hold the tungsten rod concentric. The chemically produced point can be used several times longer than ground points. This method reduces time and cost of preparing tungsten electrodes.
Continuous caustic aqueous phase electrochemical reforming (CAPER) of ethanol for producing compressed hydrogen
Caustic Aqueous Phase Electrochemical Reforming (CAPER) of ethanol produces pure compressed H 2 at lower voltages, temperatures, and energy requirements than conventional electrolysis, while capturing carbonaceous products. The CAPER flow reactor consists of stainless steel endplates, stainless steel current collectors, and a Teflon flow field. The electrodes are prepared using commercial palladium nanoparticles on carbon support for the anode and platinum nanoparticles on carbon support for the cathode. The catalyst metal loading was 1 mgcm –2 on a 10cm 2 carbon cloth for both electrodes. Our CAPER reactor produces pure H 2 at 80bar and 80°C applying voltages at ≤0.5V. The only gas-phase product detected was H 2 and any carbonaceous products were contained in the liquid phase. The H 2 was produced with 97±4% faradaic efficiency. Further, operating at smaller electrode separation distances (4mm) and 80°C increased the current density. The highest lower heating value efficiency achieved was 28% at a flow rate of 0.05mLmin –1 and an applied voltage of 0.5V. The compressed H 2 was produced at ≤20 kWh kg –1 , which is much lower than electrolysis systems that require upwards of 50 kWh kg –1 .
Rotating Disk Electrode Standardization and Best Practices in Acidic Oxygen Evolution for Low-Temperature Electrolysis
Efforts in oxygen evolution catalyst development have significantly increased and often use rotating disk electrode half-cells to evaluate intrinsic kinetics and screen materials for short-term durability. Standardizing rotating disk electrode test protocols is critical to experimental accuracy, to realistically assess their potential impact at a device level and to assess how different catalyst approaches and concepts are prioritized. The goal of this study is to provide standardized test protocols and suggest best practices to help reduce variability in ex situ materials characterization in the broader community. Specifically, these protocols focus on test cleanliness and materials choices, including how electrodes are prepared and tested, and the impact on activity observations.
Heterostructured Lepidocrocite Titanate-Carbon Nanosheets for Electrochemical Applications
Lepidocrocite-type titanates that reversibly intercalate sodium ions at low potentials (~0.6 V vs Na/Na + ) are promising anode candidates for sodium-ion batteries. However, large amounts of carbon additives are often used to improve their electrical conductivity and overcome poor cycling performance in the electrode composites. To ameliorate electronic transport issues of lepidocrocite titanate (K 0.8 Ti 1.73 Li 0.27 O 4 , KTL) in sodium-ion batteries, we have designed and synthesized heterostructures of exfoliated lepidocrocite-type titanium oxide (LTO) nanosheets with alternating carbon layers via a solution-based self-assembly approach. Positively charged dopamine (Dopa) was used as the carbon precursor and intercalated between negatively charged exfoliated titania nanosheets through electrostatic interaction. Dopa-intercalated LTO was then annealed under argon to form conductive carbon layers between titania sheets. The carbon content in the heterostructures was controlled by modifying the self-assembly conditions (i.e., pH, stirring duration, and Dopa-to-LTO ratio). Electrodes were prepared using carbonized heterostructures (LTO-C) without adding more carbon to the composites and tested in sodium half-cell configurations. Further, higher capacities and improved capacity retention over 250 cycles and lower impedance were observed, as the carbon content of LTO-C heterostructures was increased from 0% (LTO nanosheets) to 30%. These results indicate that the self-assembly approach for 2D heterostructured electrode materials is a promising strategy to overcome electronic transport limitations of layered transition-metal oxides and improve their electrochemical performance for next-generation energy storage applications.
Full Concentration Gradient-Tailored Li-Rich Layered Oxides for High-Energy Lithium-Ion Batteries
Lithium-rich layered oxides (LLOs) are prospective cathode materials for next-generation lithium-ion batteries (LIBs), but severe voltage decay and energy attenuation with cycling still hinder their practical applications. In this study, a series of full concentration gradient-tailored agglomerated-sphere LLOs are designed with linearly decreasing Mn and linearly increasing Ni and Co from the particle center to the surface. The gradient-tailored LLOs exhibit noticeably reduced voltage decay, enhanced rate performance, improved cycle stability, and thermal stability. Without any material modifications or electrolyte optimizations, the gradient-tailored LLO with medium-slope shows the best electrochemical performance, with a very low average voltage decay of 0.8 mV per cycle as well as a capacity retention of 88.4% within 200 cycles at 200 mA g –1 . These excellent findings are due to spinel structure suppression, electrochemical stress optimization, and Jahn-Teller effect inhibition. Further investigation shows that the gradient-tailored LLO reduces the thermal release percentage by as much as about 41% when the battery is charged to 4.4 V. This study provides an effective method to suppress the voltage decay of LLOs for further practical utilization in LIBs and also puts forward a bulk-structure design strategy to prepare better electrode materials for different rechargeable batteries.