Search NASA⌕ Search

SEARCH · Search NASA

Results for “electronic stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Influence of oxygen-vacancy complex /A center/ on piezoresistance of n-type silicon.

Changes in both magnitude and temperature dependence of the piezoresistance of electron-irradiated n-type silicon, induced by the latter's oxygen-vacancy complex (A center), are shown to be due to the fact that the presence of the A center causes the total conduction-band electron concentration to change with an applied stress. This change in electron concentration leads to an additional piezoresistance contribution that is expected to be important in certain many-valley semiconductors. This offers the possibility of tailoring the thermal variations of semiconductor mechanical sensors to more desirable values over limited temperature ranges.

Littlejohn, M. A.↗
DOE OSTI2023

Determining Stress in Metallic Conducting Layers of Microelectronics Devices Using High Resolution Electron Backscatter Diffraction and Finite Element Analysis

Delayed failure due to stress voiding is a concern with some aging microelectronics, as these voids can grow large enough to cause an open circuit. Local measurements of stress in the metallic layers are crucial to understanding and predicting this failure, but such measurements are complicated by the fact that exposing the aluminum conducting lines will relieve most of their stress. In this study, we instead mechanically thin the device substrate and measure distortions on the thinned surface using high resolution electron backscatter diffraction (HREBSD). These measurements are then related to the stresses in the metallic layers through elastic simulations. This study found that in legacy components that had no obvious voids, the stresses were comparable to the theoretical stresses at the time of manufacture (≈300 MPa). Distortion fields in the substrate were also determined around known voids, which may be directly compared to stress voiding models. In conclusion, the technique presented here for stress determination, HREBSD coupled with finite element analysis to infer subsurface stresses, is a valuable tool for assessing failure in layered microelectronics devices.

HREBSD↗
DOE OSTI2024

Under the microscope: Reduced activation ferritic martensitic steel Eurofer-97 following ion-Irradiation and high-temperature high-pressure water exposure

Here, this study is designed to characterise the microstructural behaviour of Eurofer-97 steel under ion irradiation and subsequent exposure to high-temperature high-pressure (HTHP) water. Eurofer-97, a ferritic-martensitic steel, has been developed to withstand the conditions of fusion reactors in the locations in contact with coolant with an elevated level of neutron flux, such as the breeder-wall blanket. The material has been studied after self-ion irradiation (using Fe ions) simulating the microstructural effects of neutron irradiation limited to the subsurface layer. The corrosion properties of the Eurofer-97 steel were studied by exposure to HTHP water up to 331 °C. Advanced microstructural characterisation using scanning, transmission electron and focused ion beam microscopy was performed on the as-received microstructure and after ion irradiation. This was then characterised after exposure for 240 h in high-temperature water. Eurofer-97 had a dense, columnar Cr-rich inner oxide, followed by a Fe-rich outer oxide layer. In the irradiated condition the grain structure and oxide itself was less ordered. No appreciable difference in oxide thickness was identified between the irradiated and unirradiated specimens after this short exposure time.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electron scattering processes: fundamentals, challenges, advances, and opportunities

Much effort has been devoted to describing qualitatively and quantitatively electron scattering processes due to their ever-increasing importance in many industrial and medical applications. We present achievements made in the last years, focusing on some of the advancements and recent progress in the field. Particular reference is made on concrete case studies to probe the level of accord in cross-section data obtained from experiments and theory, as well as on selected instrumentation developments to probe dynamics of dissociative processes induced by electron impact. We stress that the purpose of this colloquium paper is not to be a comprehensive review but rather to provide a snapshot of different research topics in electron scattering by pointing out certain challenges and, therefore, indicating opportunities to facilitate further experimental and theoretical work.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2022

Growing neoclassical tearing modes seeded via transient-induced-multimode interactions

Nonlinear extended magnetohydrodynamics simulations demonstrating seeding of neoclassical tearing modes (NTMs) via magnetohydrodynamics-transient-induced multimode interactions are presented. Simulations of NTMs are enabled by two recent NIMROD code developments: the implementation of heuristic neoclassical stresses and the application of transient magnetic perturbations (MPs) at the boundary. NTMs are driven unstable by the inherently pressure driven kinetic bootstrap current, which arises due to collisional viscosity between passing and trapped electrons. These simulations use heuristic closures that model the neoclassical electron and ion stresses. NTM growth requires a seed island, which is generated by a transiently applied MP in simulations. The capability is demonstrated using kinetic-based reconstructions with flow of a DIII-D ITER Baseline Scenario discharge (La Haye et al., in Proceedings IAEA FEC, 2020). The applied MP seeds a 2/1 NTM that grows in two phases: a slow growth phase followed by a faster robust growth phase. Additionally, an evolving sequence of higher order core modes are excited at first. Power transfer analysis shows that nonlinear interactions between the core modes and the 2/1 helps drive the initial slow growth. Once the induced 2/1 magnetic island reaches a critical width, the NTM transitions to faster robust growth, which is well described by the nonlinear modified Rutherford equation. Furthermore, this work highlights the role of nonlinear mode coupling in seeding NTMs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Uptake of polystyrene nanospheres by wheat and Arabidopsis roots in agar, hydroponics, and soil

Plant uptake of micro- and nanoplastics can lead to contamination of food with plastic particles and subsequent human consumption of plastics. There is evidence that plant roots can take up micro and nanoplastics; however, most of this evidence stems from experiments conducted with plants grown in hydroponics or agar systems where uptake of nanoparticles by roots is more favorable than when plants were grown in soil. Here, we discern the root uptake and accumulation of polystyrene nanospheres in plants grown in different growth media: agar, hydroponics, and soil. In addition, we tested the impacts of nanospheres on plant biomass and plant stress. Wheat and Arabidopsis thaliana were grown in agar, hydroponics, and soil media and exposed to polystyrene nanospheres. Three different nanospheres were used (40 nm and 200 nm carboxylate-modified and 200 nm amino-modified polystyrene) and uniformly mixed into the growth media. Plants were grown for 7 to 10 days and the roots were then examined for the presence of nanospheres by confocal laser scanning microscopy and scanning electron microscopy. Plant stress was evaluated by measuring reactive oxygen species (ROS). We observed the 40 nm nanospheres inside the plant roots, but the 200 nm nanospheres only adhered to the root cap cells showing no uptake into the roots. Furthermore, confocal images indicated that root uptake of nanospheres was favored in hydroponic solutions as compared to agar and soil media. Plant biomass was generally not affected by the nanospheres, except for hydroponically grown Arabidopsis thaliana, where biomass was significantly reduced. Small sized (40 nm) and positively charged (200 nm amino-modified) nanospheres showed higher ROS accumulation in plants than negatively charged 200 nm carboxylate-modified nanospheres. In conclusion, this study provides evidence that polystyrene nanospheres can be taken up into the interior of plant roots and cause plant stress, but these impacts are less pronounced in media where the plastic particles are less mobile, like in agar and soil media as compared to hydroponic systems.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1993

Some Observations of Solder Joint Failure Under Tensile-Compressive Stress

It has long been known that solder joints under mechanical stress are subject to failure. In early electronic systems, such failures were avoided primarily by avoiding the use of solder as a mechanical structural component. The rule was to first make sound wire connections that did not depend mechanically on solder, and only then to solder them. Careful design and miniaturization in modern electronic systems limits the mechanical stresses exerted on solder joints to values less than their yield points, and these joints have become integral parts of the mechanical structures. Unfortunately, while these joints are strong enough when new, they have proven vulnerable to fatigue failures as they age.Details of the fatigue process are poorly understood, making predictions of expected lifetimes difficult.

solder joints fatigue failure thermal cycling test↗
NASA NTRS1993

Thermal Cycling Fatigue in DIPs Mounted with Eutectic Tin-Lead Solder Joints in Stub and Gullwing Geometries

It has long been known that solder joints under mechanical stress are subject to failure. In early electronic systems, such failures were avoided primarily by avoiding the use of solder as a mechanical structural component. The rule was first to make sound wire connections that did not depend mechanically on solder, and only then to solder them. Careful design and miniaturization in modern electronic systems limits the mechanical stresses exerted on solder joints to values less than their yield points, and these joints have become integral parts of the mechanical structures. Unfortunately, while these joints are strong enough when new, they have proven vulnerable to fatigue failures as they age. Details of the fatigue process are poorly understood, making predictions of expected lifetimes difficult.

fatigue failure solder joints failure mechanisms s↗
DOE OSTI2024

Bidentate Lewis Base Ligand-Mediated Surface Stabilization and Modulation of the Electronic Structure of CsPbBr 3 Perovskite Nanocrystals

The desorption of conventional ligands from the surface of halide perovskite nanocrystals (NCs) often causes their structural instability and the deterioration of the optoelectronic properties. To address this challenge, we present an approach of using a bidentate Lewis base ligand, namely, 1,4-bis(diphenylphosphino)butane (DBPP), for the synthesis of CsPbBr 3 NCs. The phosphine group of DBPP has a strong interaction with PbBr 2 precursor, forming a highly crystalline intermediate complex during the reaction. In the presence of oleic acid, the uncoordinated phosphine group of DBPP is converted into the phosphonium cation, which strongly binds with the surface bromide of the formed CsPbBr 3 NCs through hydrogen bonding. Density functional theory calculations suggest that DBPP can strongly bind to the undercoordinated lead and surface bromide ions of CsPbBr 3 NCs through its unprotonated and protonated phosphine groups, respectively. The robust binding of DBPP with the surface of perovskite NCs helps to preserve their structural integrity under various environmental stresses. Moreover, the electron density and energy levels are regulated in DBPP-capped CsPbBr 3 NCs via the efficient transfer of electrons from the ligands to the NCs, resulting in their improved photocatalytic CO 2 reduction performance. Furthermore, our study highlights the potential of using bidentate ligands to stabilize the surface of perovskite NCs and modulate their optical and electronic properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A Tradeoff Analysis of Series / Parallel Three-Phase Converter Topologies for Wireless Extreme Chargers

In this paper, extreme fast charging (XFC) technology is studied considering the charge rates of 300 kW for wireless power transfer (WPT) applications. Tradeoff analysis of series and parallel connection of three-phase WPT system are presented by comparisons of voltage and current stresses on power electronics active / passive components. In addition, star (Y) / delta (Δ) connection configurations for three-phase wireless power transfer coupling coils are analyzed with series and LCC resonant compensation circuits. The system series and parallel connection controllability is also reviewed considering voltage and current balance techniques with output control. In a conclusion of evaluation analysis, it is revealed that each component of 300 kW wireless charging network must be designed for high fast charging system and the overall system operation need to be strategically planned for high power charging and infrastructure deployment.

Asa, Erdem↗
NASA NTRS1966

Gravitational collapse and weak interactions.

Massive star behavior during final catastrophic evolution stages, stressing effect of electron type neutrino interactions, using numerical hydrodynamics coupled with energy transfer methods

HYDRODYNAMICS↗
NASA NTRS1977

Conductive spacecraft materials development program

The objectives of this program are to provide design criteria, techniques, materials, and test methods to ensure control of absolute and differential charging of spacecraft surfaces. The control of absolute and differential charging of spacecraft cannot be effected without the development of new and improved or modified materials or techniques that will provide electrical continuity over the surface of the spacecraft. The materials' photoemission, secondary emission, thermooptical, physical, and electrical properties in the space vacuum environment both in the presence and absence of electrical stress and ultraviolet, electron, and particulate radiation, are important to the achievement of charge control. The materials must be stable or have predictable response to exposure to the space environment for long periods of time. The materials of interest include conductive polymers, paints, transparent films and coatings as well as fabric coating interweaves.

Lehn, W. L.↗
NASA NTRS1992

A compositional classification scheme for meteoritic chondrules

A compositionally based classification scheme for chondrules is proposed that will help in systematizing the wealth of data available and disentangling the effects of nebular and subsequent processes. The classification is not by texture or the composition of a single phase, or a mixture of these two, but rather is a comprehensive, systematic approach which uses the composition of the two main chondrule components. This scheme is applicable to over 95 percent of the chondrules and is easily applied using an electron microprobe. It stresses the original diversity of the chondrules and the complex yet facile way in which they respond to parent-body metamorphism. Results using this classification scheme suggest that arguments against an important role of chondrules in determining the compositional trends of the chondrites have been premature.

Sears, Derek W. G.↗