Search NASA⌕ Search

SEARCH · Search NASA

Results for “end-use”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

44 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Nano-Particle Enhanced Polymer Materials for Space Flight Applications

Recent advances in materials technology both in polymer chemistry and nano-materials warrant development of enhanced structures for space flight applications. This work aims to develop spacecraft structures based on polymer matrix composites (PMCs) that utilize these advancements.. Multi-wall carbon nano-tubes (MWCNTs) are expected ·to increase mechanical performance, lower coefficient of thermal expansion (CTE), increase electrical conductivity (mitigate electrostatic charge), increase thermal conductivity, and reduce moisture absorption of the resultant space structures. In this work, blends of MWCNTs with PETI-330 were prepared and characterized. The nano-reinforced resins were then resin transfer molded (RTM) into composite panels using M55J carbon fabric and compared to baseline panels fabricated from a cyanate ester (RS-3) or a polyimide (PETI-330) resin containing no MWCNTs. In addition, methods of pre-loading the fabric with the MWCNTs were also investigated. The effects of the MWCNTs on the resin processing properties and on the composite end-use properties were also determined.

Criss, Jim M., Jr.↗
NASA NTRS2017

Information Theoretic Evaluation of Satellite Soil Moisture Retrievals

Microwave radiometry has a long legacy of providing estimates of remotely sensed near surfacesoil moisture measurements over continental and global scales. A consistent assessment of theerrors and uncertainties associated with these retrievals is important for their effective utilization in modeling, data assimilation and end-use application environments. This article presents an evaluationof soil moisture retrieval products from AMSR-E, ASCAT, SMOS, AMSR2 and SMAPinstruments using information theory-based metrics. These metrics rely on time series analysis ofsoil moisture retrievals for estimating the measurement error, level of randomness (entropy) andregularity (complexity) of the data. The results of the study indicate that the measurement errors inthe remote sensing retrievals are significantly larger than that of the ground soil moisture measurements.The SMAP retrievals, on the other hand, were found to have reduced errors (comparable to Preprint submitted to Remote Sensing of Environment October 1, 2017those of in-situ datasets), particularly over areas with moderate vegetation. The SMAP retrievals also demonstrate high information content relative to other retrieval products, with higher levelsof complexity and reduced entropy. Finally, a joint evaluation of the entropy and complexity ofremotely sensed soil moisture products indicates that the information content of the AMSR-E, ASCAT,SMOS and AMSR2 retrievals is low, whereas SMAP retrievals show better performance. The use of information theoretic assessments is effective in quantifying the required levels of improvements needed in the remote sensing soil moisture retrievals to enhance their utility and information content.

Information theory↗
NASA NTRS2018

Building a Plastics Fabrication Laboratory on the ISS: FabLab, MANTIS, Refabricator, CRISSP, ERASMUS, and MAMBA

The objective of NASA's In Space Manufacturing program is to develop manufacturing technologies and processes necessary to provide "on-demand, sustainable operations for exploration missions." Using the ISS as a test bed, in 2014, NASA installed and successfully tested a 3D printer for in-space operations, demonstrating the 3D printing process as well as sending digital files for printing from earth to the printer. The success of this technology demonstration has shown that on-orbit manufacturing technologies can be used to limit the earth reliance for cis-lunar missions. Because of this success, numerous opportunities have been provided by NASA to further in-space manufacturing by focusing on the development of highly autonomous manufacturing systems, recycling technologies, and robotics with the ultimate goal of building a fabrication laboratory now within reach. From technologies developed for ISS activities and demonstration missions, Tethers Unlimited, Inc. (TUI) is building a Plastics Manufacturing Laboratory capable of fabricating parts on-demand and as-needed while recycling waste plastics with minimal human interaction required. Parts will be manufactured through additive manufacturing. Precision machining will ensure manufactured parts are in tolerance with the end-use requirements. Recycling waste plastics will enable both waste from the crew and waste from processing to be re-processed into something new. In addition, these manufacturing and recycling technologies are supported by part verification/validation technique and robotic servicing, minimizing human interaction with the system and eventually enabling unmanned off-world manufacturing.

Muhlbauer, Rachel↗
NASA NTRS2018

Large Scale Cryogenic Storage with Active Refrigeration

Storage and transfer of cryogenic liquefied gases on volume scales from under 10 liters for lab use, up to hundreds of millions of liters for industrial applications is of paramount importance across a vast range of industries. Traditionally, these commodities have been stored at or near the normal boiling point due to relative ease of operation and safety-related considerations; however, this also means that some percentage will always be lost due to environmental heat leaking into the vessel and causing boil-off. These losses become more concerning as scales increase, and are of particular importance for high-cost commodities such helium and hydrogen. Additionally, the normal boiling point marks the highest liquid density achievable; which becomes a strong driver of end-use system designs such as space launch vehicles. Recent development and testing of an Integrated Refrigeration and Storage (IRAS) system for liquid hydrogen has proven that next generation cryogenic storage operations such as zero boil-off and densification are feasible on a large scale. This IRAS system married an 850 Watt at 20 Kelvin reverse-Brayton cycle commercial cryogenic refrigerator with a 125,000 liter LH2 storage tank via and internal tubular heat exchanger. This allowed heat to be removed directly from the hydrogen, and by extension, provided a means to control the bulk thermodynamic state. Zero boil-off, in-situ liquefaction, and densification down to the triple point was performed during testing, and data such as fluid temperature profiles and tank pressure were gathered. Details regarding the design, setup, and testing of the IRAS system are discussed herein, and the data used to anchor various physics models created to predict the behavior of the system during transient and steady state operation. It is hoped that these efforts will provide a useful basis for the design and implementation of future large scale IRAS systems across numerous industries.

Swanger, Adam M.↗
NASA NTRS2020

Simulated Galactic Cosmic Ray and Solar Particle Event Radiation Effects on Inflatable Habitat, Composite Habitat, Space Suit and Space Hatch Cover Materials

The effect of particle radiation representative of galactic cosmic ray (GCR) and solar particle event (SPE) radiation on polymeric materials used in deep space mission environments is largely unknown. For NASA, this uncertainty represents an unquantified mission risk. To better quantify this risk, selected polymeric materials used in inflatable habitats, composite habitats, space suits and space hatch covers are irradiated at the Brookhaven National Laboratory, after which changes in relevant end-use properties are measured. The irradiated materials are lightweight candidates having critical functions such as ripstops, permeation barriers, micrometeoroids and orbital debris (MMOD) shield layers and restraint layers.The effect of several types of particle radiation are evaluated. To evaluate GCR effects, high-energy (1 GeV) protons and iron nucleons are used. To evaluate SPE effects, intermediate energy (ca. 20 to 40 MeV) protons are used. In addition, two mission scenarios are evaluated: a Mars mission cycle (space suit materials) and a worst-case 50 year deep space mission cycle (all materials). Lastly, a common polymer (high density polyethylene (HDPE)) is subjected to accelerated aging and radiation exposure to determine if a combined physical aging/radiation effect exists.The level of radiation induced property change observed in this study after exposure of polymers to kGy levels of intermediate and high energy ions is often significant and is quantitatively comparable to the level of change reported for similar materials exposed to MGy levels of low energy protons, electrons and gamma-radiation. This suggests that intermediate and high energy ions encountered in space may cause more damage than low energy forms of radiation due to displacement and linear energy transfer (LET) effects. For these reasons, it is recommended that final approval for mission use be made by the appropriate NASA material and structural review boards to ensure radiation induced changes in candidate materials do not interfere with their engineering function in the intended mission application. Since the materials tested in this report received doses exceeding actual mission doses, the results are considered conservative as a first approximation. However, caution must be exercised when evaluating radiation effects in the absence of other secondary factors know to contribute to degradation. In the addition to radiation type and energy, the results presented in this study show that molecular composition, orientation, stress and physical aging can also contribute to or influence degradation. Other factors such as polymer formulation, secondary radiation effects, stress, exposure to elevated temperature, thermal cycling and exposure to ozone were not investigated here, but must be considered when performing a comprehensive evaluation of a polymeric materials suitability for service in a space radiation environment. Only when the total sum of these factors operating in concert with radiation are accounted for, can accurate assessments of a material's suitability be made.

Jess M. Waller↗
NASA NTRSDate not supplied

Metallic Environmentally Resistant Coating Rapid Innovation Initiative

Lightweight alloys such as aluminum (Al) and titanium (Ti) are often specified for space systems to minimize mass while maintaining structural integrity [1,2]. Such alloys however, have poor tribological response (high friction and wear), especially in extreme space environments, which becomes worse with the additional presence of lunar regolith. This leads to short lifetimes and premature failures that will ultimately limit long term operations on the lunar surface [2]. This project is addressing this technology gap by developing advanced wear- and radiation-resistant coatings for lightweight parts to extend the life-time and sustainability of both lunar and Martian assets. Ceramics were considered for their high wear resistance, but were rejected because of their low fracture toughness, which would be especially problematic for structural components. The novel and existing coating technologies and deposition methods are being tested in this project. The coating materials are Boron Nitride-Aluminum (BN-Al), Nickle Titanium (NiTi), Aluminum Oxide (AlO3), Ti64 with hBN at 2 and 10 vol percent (Ti-2vol%hBN and Ti-10vol%hBN), and the deposition techniques are high pressure cold-spray (CS) and ambient and vacuum plasma-spray (APS and VPS) [3,4,5]. BN-Al, NiTi, Ti-2vol%hBN, and Ti-10vol%hBN were applied with all three deposition techniques, and AlO3 was applied only using the APS deposition technique. A tungstenite (WS2) film was applied to the NiTi VPS coating. The coating and deposition technique configurations are being tested against several key end-use performance parameters. The parameters include the capabilities of the coatings under wear environments such as regolith simulant, thermal cycling from high (120°C) to cryogenic (-173°C), high vacuum (~10-7 torr), and pre- and post-exposure to ionizing particle radiation. Wear tests include pin on disk, three-body abrasion, and surface erosion by high velocity regolith impacts. The initial down selection is being performed using on virgin and environmental exposure samples using pin on disk and three body abrasion wear tests. From preliminary assessment of this testing, a few configurations were eliminated. Ti-10vol%hBN could not be applied using CS application and NiTi could not be applied using APS or CS application so these configurations did not get tested. Early pin on disk wear tests showed poor wear performance of BN-Al so this coating was eliminated early in the testing process. AlO3 on Al substrate did not survive thermal cycling, but wear testing is continuing for AlO3 on Ti substrate. A more detailed analysis is being con-ducted to further reduce the number of configuration for phase II and III. Phase II testing will include conventionally and additively manufactured substrates with surface erosion testing. In phase III, the coatings will be applied to three mechanism types: channel and slot, ball and socket, and a hinge joint. Each will demonstrate a different type of wear incidence. The mechanisms and their base materials are of direct interest to the end users and infusion points: the Human Landing System (HLS) and the Lunar Surface Innovation Initiative (sustained lunar surface operations). The technology development project is based out of Marshall Space Flight Center, has partnered with Florida International University (Miami, FL) and Plasma Processes (Huntsville, Al), and is supported by a group of NASA mentors from different centers.

dust mitigation↗
NASA NTRS2023

Machine Learning to Increase the Quality and Repeatability of 3D Printing - Workflow

The imprecise nature of three-dimensional (3D) printing limits the technology’s use beyond prototyping. For production of end-use parts, such as those for aerospace applications, improvements are needed to enhance quality and repeatability. Much of the difficulty in obtaining high quality printed parts lies in finding optimum printing parameters. Currently, this requires trial and error performed by an expert. Finding the optimum printing parameters is also obfuscated by the variation in optimum parameters throughout the part due to part geometry and printer effects. To allow for locally optimized printing parameters, one can envision a machine learning algorithm that could take in an object, predict the best printing parameters, and communicate these parameters to a printer. With this scenario in mind, we developed a tool that can predict and implement locally optimized printing parameters in 3D printing. This tool consists of elements designed to detect errors in a printed part, predict the probability of local flaws occurring at each point in the part, and select the optimal local parameters for the highest quality part given hardware limitations. The results of this work were highlighted in Advanced Materials Technologies. In this paper, we will discuss in greater depth the workflow and algorithms involved with this tool that were not detailed in the journal publication.

additive manufacturing↗
NASA NTRS2023

Cryogenic Oxygen Storage Modules with Carbon Dioxide Sequestration for Environmental Control and Life Support Applications

NASA Kennedy Space Center engineers developed a Cryogenic Oxygen Storage Module (COSM) to store oxygen in solid-state form and deliver it as a gas to an end-use environmental control and/or life support system. Additionally, the COSM can scrub out nuisance or containment gases such as carbon dioxide and/or water vapor in conjunction with supplying oxygen, forming a synergistic system when used in a closed-loop application. Closed-loop life support systems require both oxygen supply and removal of toxic or nuisance gases such as CO2 from the breathing loop. In most deployed systems, these two requirements are accomplished independently. COSM combines these capabilities to work simultaneously which may allow for reduced system volume, mass, complexity and cost of a rebreathing device.

Jeffrey A Kohler↗