Search NASA⌕ Search

SEARCH · Search NASA

Results for “fuel spray”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Effect of fuel sprays on emissions

A research gas turbine combustor was operated under realistic conditions such that the influence of individual variables (in particular, fuel spray characteristics) on emissions could be determined. The special combustor allows independent control over drop size, fuel-air ratio, air inlet temperature, pressure, reference velocity, and residence time. Also, it lends itself to theoretical modeling and turbulent intensity measurements through use of laser velocimetry. Emission results for a range of operations are presented. A number of graphs show which show the variations of emissions levels with one variable at a time are included. In every case, the fuel is jet A, the pressure is atmospheric, and combustion is limited to a primary zone.

Nicholls, J. A.↗
NASA NTRS1933

The NACA Apparatus for Studying the Formation and Combustion of Fuel Sprays and the Results from Preliminary Tests

This report describes the apparatus as designed and constructed at the Langley Memorial Aeronautical Laboratory, for studying the formation and combustion of fuel sprays under conditions closely simulating those occurring in a high-speed compression-ignition engine. The apparatus consists of a single-cylinder modified test engine, a fuel-injection system so designed that a single charge of fuel can be injected into the combustion chamber of the engine, an electric driving motor, and a high-speed photographic apparatus. The cylinder head of the engine has a vertical-disk form of combustion chamber whose sides are glass windows. When the fuel is injected into the combustion chamber, motion pictures at the rate of 2,000 per second are taken of the spray formation by means of spark discharges. When combustion takes place the light of the combustion is recorded on the same photographic film as the spray photographs. The report includes the results of some tests to determine the effect of air temperature, air flow, and nozzle design on the spray formation.

Rothrock, A M↗
NASA NTRS1937

Effects of Air-Fuel Spray and Flame Formation in a Compression-Ignition Engine

High-speed motion pictures were taken at the rate of 2,500 frames per second of the fuel spray and flame formation in the combustion chamber of the NACA combustion apparatus. The compression ratio was 13.2 and the speed 1,500 revolutions per minute. An optical indicator was used to record the time-pressure relationship in the combustion chamber. The air-fuel ratio was varied from 10.4 to 365. The results showed that as the air-fuel ratio was increased definite stratification of the charge occurred in the combustion chamber even though moderate air flow existed. The results also showed the rate of vapor diffusion to be relatively slow.

Rothrock, A M↗
NASA NTRS1992

Studies on fuel spray characteristics in high-pressure environment

The present study deals with several issues involving the improvement of physical submodels and the computational efficiency in modeling dense fuel sprays. To improve the computational efficiency, a parcel PDF approach is implemented which can account for turbulent dispersion within each computational parcel. The advantage of a parcel PDF tracking method is to reduce the number of computational parcels representing the spray dynamics as well as to obtain grid-independent solutions for two-phase flows. To account for the dense spray effects, an existing drop collision and coalescence model, two breakup models, and a Reitz's wave instability model were used. These models were incorporated into a state-of-the-art multiphase all-speed transient flow solution procedure. Comparative performance for two breakup models as well as the turbulence modulation effects are also studied. Validation cases include the nonevaporating and evaporating solid-cone dense sprays. The predictions show a reasonably good agreement with available experimental results in terms of spray penetration, drop sizes, gas and drop mean velocities, and gas and drop rms velocities. The numerical results indicate that the present parcel PDF model has the capability of accurately representing drop dispersion in dense sprays with manageable number of computational parcels.

Shang, H. M.↗
NASA NTRS1979

The effect of fuel sprays on emissions from a gas turbine combustor

A research gas turbine combustor which allows for independent control of drop size, fuel/air ratio, air inlet temperature, pressure, reference velocity, and residence time has been used to study the influence of fuel spray characteristics on primary zone emissions. Local concentrations of oxides of nitrogen, carbon monoxide and unburned hydrocarbons at various locations in the flow, local gas temperature, gas velocity, and the turbulence intensity (measured with laser velocimetry) are obtained. A comprehensive data analysis program to compute the local fuel/air ratio and the sum of the mole fractions of the species present confirms the validity of the emissions data. Increasing drop size is correlated with an increase in unburned hydrocarbons, while increasing residence time is associated with sharp decreases in hydrocarbons and carbon monoxide and an increase in oxides of nitrogen.

Nicholls, J. A.↗
NASA NTRS1983

Pollutant Formation in Monodisperse Fuel Spray Combustion

The combustion of liquid sprays represents an extremely important class of combustion processes. In the transition region, encompassing droplet sizes in the range of 25-80 micron diameter, the mixing and evaporation processes are both incomplete at the flame front and burning occurs in a combined diffusive and premixed fashion. Under these conditions, the relative importance of heterogeneous and homogeneous effects in dominating the combustion process is switched and gives rise to a number of interesting phenomena. NO (sub x) formation in monodisperse spray combustion was investigated with the following specific objectives: (1) to quantitatively determine the effect of droplet size, number density, etc. on NO sub x formation in monodisperse fuel spray combustion; and (2) to isolate the important physical and chemical phenomena in NO sub x formation in these combustion systems.

Cernansky, N. P.↗
NASA NTRS1995

Stabilization Of Combustion Of Sprayed Fuel

Several modifications of nozzle spraying liquid propellant into combustion chamber proposed to stabilize combustion. Proposed changes in design of nozzle alter flow field in combustion chamber, according to fluid-mechanical principles, in such way as to suppress oscillations. Various alternative nozzle configurations include bluff or toroidal body to generate turbulence. Other features helping to suppress oscillations include down-stream recirculation zones, baffles, and damping cavities. Similar modifications help to suppress oscillations in industrial combustion chambers and in commercial and domestic oil-burning furnaces.

Voecks, Gerald E.↗
NASA NTRS1987

Numerical simulation of the flow field and fuel sprays in an IC engine

A two-dimensional model for axisymmetric piston-cylinder configurations is developed to study the flow field in two-stroke direct-injection Diesel engines under motored conditions. The model accounts for turbulence by a two-equation model for the turbulence kinetic energy and its rate of dissipation. A discrete droplet model is used to simulate the fuel spray, and the effects of the gas phase turbulence on the droplets is considered. It is shown that a fluctuating velocity can be added to the mean droplet velocity every time step if the step is small enough. Good agreement with experimental data is found for a range of ambient pressures in Diesel engine-type microenvironments. The effects of the intake swirl angle in the spray penetration, vaporization, and mixing in a uniflow-scavenged two-stroke Diesel engine are analyzed. It is found that the swirl increases the gas phase turbulence levels and the rates of vaporization.

Nguyen, H. L.↗
NASA NTRS1985

Analysis of the effects of fuel spray characteristics on NO(x) formation

Results from experimental and analytical studies on NO(x) formation in a one-dimensional monodisperse spray combustion system are reported. In a previous investigation, an optimum droplet diameter was reported for minimizing NO(x) emissions. In this paper, the effects of enhanced prevaporization and droplet interactions in addition to droplet size effects on NO(x) formation are investigated by air preheating experiments. These phenomena have been incorporated into an analytical model which predicts NO(x) formed from the combustion of monodisperse fuel sprays. Both, experimental and computed results indicate the importance of the extent of prevaporization and droplet interactions on NO(x) production. Preflame vaporization controls the gas phase stoichiometry which has a significant effect on the volume of the hot gases surrounding a fuel droplet where NO(x) is formed. On the other hand, the release of fuel vapor from the droplet to the reaction zone is influenced by droplet interactions which reduce the volume of the hot gases and NO(x) production by bringing the flame closer to the droplet surface.

Sarv, H.↗
NASA NTRS1986

Combustion characteristics in the transition region of liquid fuel sprays

A number of important effects have been observed in the droplet size transition region in spray combustion systems. In this region, where the mechanism of flame propagation is transformed from diffusive to premixed dominated combustion, the following effects have been observed: (1) maxima in burning velocity; (2) extension of flammability limits; (3) minima in ignition energy; and (4) minima in NOx formation. A monodisperse aerosol generator has been used to form and deliver a well controlled liquid fuel spray to the combustion test section where measurements of ignition energy have been made. The ignition studies were performed on monodisperse n-heptane sprays at atmospheric pressure over a range of equivalence ratios and droplet diameters. A capacitive discharge spark ignition system was used as the ignition source, providing independent control of spark energy and duration. Preliminary measurements were made to optimize spark duration and spark gap, optimum conditions being those at which the maximum frequency or probability of ignition was observed. Using the optimum electrode spacing and spark duration, the frequency of ignition was determined as a function of spark energy for three overall equivalence ratios (0.6, 0.8, and 1.0) and for initial droplet diameters of 25, 40, 50, 60, and 70 micro m.

Cernansky, N. P.↗
DOE OSTI2021

X-Ray Characterization of Real Fuel Sprays for Gasoline Direct Injection

Here, the effects of fuel blend properties on spray and injector performance has been investigated in a side-mount injector for gasoline direct injection (GDI) using two certification fuel blends: Euro 5 and Euro 6. Several X-ray diagnostic techniques were conducted to characterize the injector and spray morphology. Detailed internal geometry of the GDI injector was resolved to 1.8 μm, through the use of hard X-ray tomography. The geometry characterization of this six-hole GDI, side mount injector, quantifies relevant hole and counterbore dimensions and reveals the intricate details within the flow passages, including surface roughness and micron-sized features. Internal valve motion was measured with a temporal resolution of 20 μs and a spatial resolution of 2.0 μs, for three injection pressures and several injector energizing strategies. The needle motion for both fuels exhibits similar lift profiles for common energizing commands. A combination of X-ray radiography and ultra-small-angle X-ray scattering (USAXS) was used to characterize the fuel mass distribution and the droplet sizing, respectively. Tomographic spray radiography revealed the near-nozzle distribution of fuel mass for each of the fuels and the asymmetry produced by the angled nozzles. Under evaporative conditions, the two fuels show minor differences in peak fuel mass distribution during steady injection, though both exhibit fluctuations in injection during the early, transient phase. USAXS measurements of the path-specific surface area of the spray indicated lower peak values for the more evaporative conditions in the near nozzle region.

09 BIOMASS FUELS↗
NASA NTRS1994

High Velocity Oxygen Fuel Spraying of Erosion and Wear Resistant Coatings on Jet Engine Parts

High velocity oxygen fuel (HVOF) spraying is the most recent development in the field of thermal spraying. The importance of this technique for the repair and new part manufacturing of jet engine parts is rapidly increasing. The HVOF uses a supersonic oxygen-fuel flame to heat and accelerate the powder particles that form the coating. The high particle velocity results in a high density and a low porosity, a high bond strength, and a high macro and micro hardness of the coating. The high quality of the HVOF coatings makes it possible to use these coatings on high loaded, rotating parts in jet engines. This paper will highlight the use of HVOF processes to apply erosion resistant cermet coatings to high pressure compressor blades. These blades are exposed to severe erosion. Next to the D-gun process, HVOF spraying is the only nonproprietary technique that can be used to apply these high performance coatings. Also the use of the HVOF process to apply wear resistant coatings and superalloys to jet engine parts will be discussed. The difference between HVOF coatings and plasma sprayed coatings will be highlighted. During HVOF spraying, the parts are exposed to a high heat flow. Solutions to avoid overheating, especially of titanium parts, will be presented.

A T J Verbeek↗
DOE OSTI2023

Modeling Ethanol-Blend Fuel Sprays under Direct-Injection Spark-Ignition Engine Conditions

Computational modeling of fuel-injection and fuel-impingement processes was carried out to provide insight into previous experimental results obtained from a direct-injection spark-ignition research engine operated with various ethanol and aromatic fuel blends. Seven model fuels were evaluated using both single- and split-injection strategies. Model results showed that droplet vaporization enriched the concentrations of aromatic species in the liquid phase, especially those with low vapor pressure, and ethanol-containing fuels altered droplet sizes and led to increased liquid-phase mass in the cylinder. For the spray-modeling conditions studied, most of the injected fuel remained in the liquid phase, which would be expected to result in more fuel impingement on cylinder or piston surfaces. Fuel impinging on lower cylinder-temperature surfaces was found to create wall films that could interact with the piston during the compression stroke. Fuel impinging on hotter piston-temperature surfaces vaporized more readily, but for fuels with high ethanol and aromatic content, wall films remained and were highly concentrated with lower vapor pressure and aromatic compounds. These films could lead to pool fires during combustion and therefore significant particulate matter emissions.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗
DOE OSTI2023

Representative Phenomena of Cyclic Turbulent Combustion in High-Pressure Fuel Sprays

Abstract Cyclic variations in conventional diesel combustion engines can lead to large differences in engine out emissions even at steady operation. This study uses an optically accessible constant-pressure flow chamber to acquire fuel injections in quick succession to analyze mixing, auto-ignition, and combustion of diesel-surrogate n-heptane using multiple high-speed optical diagnostics. Prior studies have utilized fewer injections and/or they rely on analysis of ensemble average behavior. These approaches do not yield information on injection-to-injection variation or provide confidence in utilizing individual injection measurements for high-fidelity computational fluid dynamics(CFD) model validation. In this study, a large set of 500 injections is used to obtain global parameters including liquid length, vapor penetration length, ignition delay time, and lift-off length. Results for multiple injections are presented to illustrate large injection to injection variations. Potential sources for these variations are analyzed to conclude localized, small scale turbulence and rate of injection variations as the likely sources. Then, a statistical method based on z-scores is proposed and implemented to identify instantaneous injections that best represent the bulk data-set of jet boundaries measured independently by three different diagnostics. This synthesis of statistics-guided screening of data set and ensemble-average analysis offers higher confidence for CFD model validation relying upon both a representative single and average injection results.

42 ENGINEERING↗
NASA NTRS1987

Spark Ignition of Monodisperse Fuel Sprays

A study of spark ignition energy requirements was conducted with a monodisperse spray system allowing independent control of droplet size, equivalent ratio, and fuel type. Minimum ignition energies were measured for n-heptane and methanol sprays characterized at the spark gap in terms of droplet diameter, equivalence ratio (number density) and extent of prevaporization. In addition to sprays, minimum ignition energies were measured for completely prevaporized mixtures of the same fuels over a range of equivalence ratios to provide data at the lower limit of droplet size. Results showed that spray ignition was enhanced with decreasing droplet size and increasing equivalence ratio over the ranges of the parameters studied. By comparing spray and prevaporized ignition results, the existence of an optimum droplet size for ignition was indicated for both fuels. Fuel volatility was seen to be a critical factor in spray ignition. The spray ignition results were analyzed using two different empirical ignition models for quiescent mixtures. Both models accurately predicted the experimental ignition energies for the majority of the spray conditions. Spray ignition was observed to be probabilistic in nature, and ignition was quantified in terms of an ignition frequency for a given spark energy. A model was developed to predict ignition frequencies based on the variation in spark energy and equivalence ratio in the spark gap. The resulting ignition frequency simulations were nearly identical to the experimentally observed values.

Danis, Allen M.↗
NASA NTRS1989

Gas density effect on dropsize of simulated fuel sprays

Two-phase flow in pneumatic two-fluid fuel nozzles was investigated experimentally to determine the effect of atomizing-gas density and gas mass-flux on liquid-jet breakup in sonic-velocity gas-flow. Dropsize data were obtained for the following atomizing-gases: nitrogen; argon; carbon dioxide; and helium. They were selected to cover a gas molecular-weight range of 4 to 44. Atomizing-gas mass-flux ranged from 6 to 50 g/sq cm-sec and four differently sized two-fluid fuel nozzles were used having orifice diameters that varied from 0.32 to 0.56 cm. The ratio of liquid-jet diameter to SMD, D sub o/D sub 32, was correlated with aerodynamic and liquid-surface forces based on the product of the Weber and Reynolds number, and gas-to-liquid density ratio, rho sub g/rho sub 1. To correlate spray dropsize with breakup forces produced by using different atomizing-gases, a new molecular-scale dimensionless group was derived. The derived dimensionless group was used to obtain an expression for the ratio of liquid-jet diameter to SMD, D sub o/D sub 32. The mathematical expression of this phenomenon incorporates the product of the Weber and Reynolds number, liquid viscosity, surface tension, acoustic gas velocity, the RMS velocity of gas molecules, the acceleration of gas molecules due to gravity, and gas viscosity. The mathematical expression encompassing these parameters agrees well with the atomization theory for liquid-jet breakup in high velocity gas flow. Also, it was found that at the same gas mass-flux, helium was considerably more effective than nitrogen in producing small droplet sprays with SMD's in the order of 5 micrometers.

Ingebo, Robert D.↗
NASA NTRS1989

Gas density effect on dropsize of simulated fuel sprays

Two-phase flow in pneumatic two-fluid fuel nozzles was investigated experimentally to determine the effect of atomizing-gas density and gas mass-flux on liquid-jet breakup in sonic-velocity gas-flow. Dropsize data were obtained for the following atomizing-gases: nitrogen; argon; carbon dioxide; and helium. They were selected to cover a gas molecular-weight range of 4 to 44. Atomizing-gas mass-flux ranged from 6 to 50 g/sq cm-sec and four differently sized two-fluid fuel nozzles were used having orifice diameters that varied from 0.32 to 0.56 cm. The ratio of liquid-jet diameter to SMD, D sub o/D sub 32, was correlated with aerodynamic and liquid-surface forces based on the product of the Weber and Reynolds number, We*Re, and gas-to-liquid density ratio, rho sub g/rho sub l. To correlate spray dropsize with breakup forces produced by using different atomizing-gases, a new molecular-scale dimensionless group was derived. The derived dimensionless group was used to obtain an expression for the ratio of liquid-jet diameter to SMD, D sub o/D sub 32. The mathematical expression of this phenomenon incorporates the product of the Weber and Reynolds number, liquid viscosity, surface tension, acoustic gas velocity, the RMS velocity of gas molecules, the acceleration of gas molecules due to gravity, and gas viscosity. The mathematical expression encompassing these parameters agrees well with the atomization theory for liquid-jet breakup in high velocity gas flow. Also, it was found that at the same gas mass-flux, helium was considerably more effective than nitrogen in producing small droplet sprays with SMD's in the order of 5 micrometers.

Ingebo, Robert D.↗