Search NASA⌕ Search

SEARCH · Search NASA

Results for “hot-wire anemometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Experiments on the stability of crossflow vortices in swept-wing flows

Experiments are conducted which demonstrate the feasibility of creating crossflow vortices in a flat-plate flow. A swept leading edge and contoured wind-tunnel walls produce a strong pressure gradient and a typical swept-wing flow on the plate. Detailed three-dimensional measurements, made within the boundary layer using hot-wire anemometry, are supplemented with different flow-visualization techniques. Data are presented on the mean flow characteristics as well as on the behavior of the crossflow vortices. Comparisons are made with theoretical flow-field and stability calculations.

Saric, W. S.↗
NASA NTRS1985

Experimental study of disturbances produced in a pre-transitional laminar boundary layer by weak freestream turbulence

The high-amplitude, low-frequency, disturbances generated in a Blasius boundary layer by grid-produced freestream turbulence were studied by means of hot-wire anemometry and by flow visualization. Emphasis was placed on determining the cause and nature of these, and on their effect upon the mean flow profile. It was found that the motion in the layer was intrinsically three-dimensional, according to which the fronts, of Tollmien-Schlichting waves became warped. Evidence of streamwise vorticity was noted. At Reynolds numbers near 1.6 million, the maximum attained, sharp velocity gradients appeared locally. With increase of grid size, there appeared turbulent spots which were wider than the coherence scale of the background motion.

Kendall, J. M.↗
NASA NTRS1985

Periodic oscillations observed in swirling flows with and without combustion

Data obtained by laser induced Rayleigh scattering and hot-wire anemometry are used to study periodic oscillations in swirling flows with and without combustion present. Power spectral density functions reveal the presence of energetic, periodic oscillations in the flow. A band of low frequency oscillations (25-100 Hz) is observed on and near the centerline in the presence of a recirculation zone and is attributed to axial oscillations of the recirculation zone which are amplified with combustion by an interaction between the mechanism for flow recirculation and flow changes induced by combustion. High frequency oscillations between 300-500 Hz are observed in an annular region located in the vortex core. A stability analysis is performed, and it is concluded that these oscillations are most likely helical waves resulting from hydrodynamic instability in the vortex core upstream of the test section.

Gouldin, F. C.↗
NASA NTRS1987

Flowfield measurements in a separated and reattached flat plate turbulent boundary layer

The separation and reattachment of a large-scale, two-dimensional turbulent boundary layer at low subsonic speed on a flat plate has been studied experimentally. The separation bubble was 55 cm long and had a maximum bubble thickness, measured to the height of the mean dividing streamline, of 17 cm, which was twice the thickness of the inlet boundary layer. A combination of laser velocimetry, hot-wire anemometry, pneumatic probing techniques, and flow visualization were used as diagnostics. Principal findings were that an outer inviscid rotational flow was defined which essentially convected over the blockage associated with the inner, viscously dominated bubble recirculation region. A strong backflow region in which the flow moved upstream 100 percent of the time was measured near the test surface over the central 35 percent of the bubble. A laminar backflow boundary layer having pseudo-turbulent characteristics including a log-linear velocity profile was generated under the highly turbulent backflow. Velocity profile shapes in the reversed flow region matched a previously developed universal backflow profile at the upstream edge of the separation region but not in the steady backflow region downstream. A smoke flow visualization movie and hot-film measurements revealed low frequency nonperiodic flapping at reattachment. However, forward flow fraction data at reattachment and mean velocity profiles in the redeveloping boundary layer downstream of reattachment correlated with backward-facing step data when the axial dimension was scaled by the distance from the maximum bubble thickness to reattachment.

Patrick, William P.↗
NASA NTRS1986

The influence of free-stream turbulence on separation of turbulent boundary layers in incompressible, two-dimensional flow

Experiments were conducted to determine if free-stream turbulence scale affects separation of turbulent boundary layers. In consideration of possible interrelation between scale and intensity of turbulence, the latter characteristic also was varied and its role was evaluated. Flow over a 2-dimensional airfoil in a subsonic wind tunnel was studied with the aid of hot-wire anemometry, liquid-film flow visualization, a Preston tube, and static pressure measurements. Profiles of velocity, relative turbulence intensity, and integral scale in the boundary layer were measured. Detachment boundary was determined for various angles of attack and free-stream turbulence. The free-stream turbulence intensity and scale were found to spread into the entire turbulent boundary layer, but the effect decreased as the airfoil surface was approached. When the changes in stream turbulence were such that the boundary layer velocity profiles were unchanged, detachment location was not significantly affected by the variations of intensity and scale. Pressure distribution remained the key factor in determining detachment location.

Potter, J. Leith↗
NASA NTRS1987

A low-density boundary-layer wind tunnel facility

This abstract describes a low-density wind-tunnel facility that was established at NASA Ames in order to aid interpretation and understanding of data received from the Mariner and Viking spacecraft through earth-based simulation. The wind tunnel is a boundary-layer type which is capable of operating over a range of air densities ranging from 0.01 to 1.24 kg/cu m, with the lower values being equivalent to the near-surface density of the planet Mars. Although the facility was developed for space and extraterrestrial simulation, it also can serve as a relatively large-scale, low-density aerodynamic test facility. A description of this unique test facility and some Pitot-tube and hot-wire anemometry data acquired in the facility are presented.

White, B. R.↗
NASA NTRS1987

Characteristics of a separating confluent boundary layer and the downstream wake

Measurements of pressure and velocity characteristics are presented and analyzed for flow over and downstream of a NACA 4412 airfoil equipped with a NACA 4415 single-slotted flap at high angle of attack and close to maximum lift. The flow remained attached over the main element while a large region of recirculating flow occurred over the aft 61 percent of the flap. The airfoil configuration was tested at a Mach number of 0.09 and a chord Reynolds number of 1.8x10 to the 6th power in the NASA Ames Research Center 7- by 10-Foot Wind Tunnel. Measurement of mean and fluctuation velocities were obtained in regions of recirculation and high turbulence intensity using 3-D laser velocimetry. In regions where the flow had a preferred direction and relatively low turbulence intensity, hot-wire anemometry was used. Emphasis was placed on obtaining characteristics in the confluent boundary layer, the region of recirculating flow, and in the downstream wake. Surface pressure measurements were made on the main airfoil, flap, wind tunnel roof and floor. It is thought likely that because the model is large when compared to the wind tunnel cross section, the wind tunnel floor and ceiling interference should be taken into account when the flow field is calculated.

Adair, Desmond↗
NASA NTRS1987

Changes in the turbulent boundary layer structure associated with net drag reduction by outer layer manipulators

A specially designed wind tunnel was used to examine the effects of tandemly arranged parallel plate manipulators (TAPPMs) on a turbulent boundary-layer structure and the associated drag. Momentum balances, as well as measurements of the local shear stress from the velocity gradient near the wall, were used to obtain the net drag and local skin friction changes. Two TAPPMs, identical except for the thickness of their plates, were used in the study. Results with .003 inch plates were a maximum net drag reduction of 10 percent at 58 beta sub o (using a momentum balance). At 20 beta sub o, simultaneous laser sheet flow visualization and hot-wire anemometry data showed that the Reynolds stress in the large eddies was significantly reduced, as were the streamwise and normal velocity components. Using space-time correlations the reductions were again identified. Furthermore, quantitative flow visualization showed that the outward normal velocity of the inner region was also significantly decreased in the region around 20 beta sub o. However, throughout the first 130 beta sub o, the measured sublayer thickness with the TAPPMs in place was 15 to 20 percent greater. The data showed that the skin friction, as well as the structure of the turbulence, was strongly modified in the first 35 beta sub o, but that they both significantly relaxed toward unmanipulated boundary layer values by 50 beta sub o.

Rashidnia, N.↗
NASA NTRS1988

Characteristics of merging shear layers and turbulent wakes of a multi-element airfoil

Flow characteristics in the vicinity of the trailing edge of a single-slotted airfoil flap are presented and analyzed. The experimental arrangement consisted of a NACA 4412 airfoil equipped with a NACA 4415 flap whose angle of deflection was 21.8 deg. The flow remained attached over the model surfaces except in the vicinity of the flap trailing edge where a small region of boundary-layer separation extended over the aft 7 percent of flap chord. The flow was complicated by the presence of a strong, initially inviscid jet emanating from the slot between airfoil and flap, and a gradual merging of the main airfoil wake and flap suction-side boundary layer. Downstream of the flap, the airfoil and flap wakes fully merged to form an asymmetrical curved wake. The airfoil configuration was tested at an angle of attack of 8.2 deg, at a Mach number of 0.09, and a chord based Reynolds number of 1.8 x 10 to the 6th power in the Ames Research Center 7- by 10-Foot Wind Tunnel. Surface pressure measurements were made on the airfoil and flap and on the wind tunnel roof and floor. It was estimated that the wall interference increased the C sub L by 7 percent and decreased the C sub M by 4.5 percent. Velocity characteristics were quantified using hot-wire anemometry in regions of flow with preferred direction and low turbulence intensity. A 3-D laser velocimeter was used in regions of flow recirculation and relatively high turbulence intensity.

Adair, Desmond↗
NASA NTRS1987

Experimental study of three shock wave/turbulent boundary layer interactions

The paper presents a systematic study of the supersonic flow of a turbulent boundary layer over several compression-corner models. The wind tunnel and the compression-corner models (ramps fitted with aerodynamic fences to minimize three-dimensional effects) were identical with those used by Settles et al. (1979); constant-temperature hot-wire anemometry was used for the mass-flow measurements. The turning angles used for the compression corners were 8, 16, and 20 deg. In all three flow cases, the shock wave/turbulent flow interaction did amplify the turbulent stresses dramatically, with amplification increasing with increasing turning angle. However, different stress components were amplified by different amounts.

Smits, Alexander J.↗
NASA NTRS1988

Turbulent separated flow in the vicinity of a single-slotted airfoil flap

Detailed measurements of pressure and velocity characteristics are presented and analyzed for flow over and downstream of a NACA 4412 airfoil equipped with a NACA 4415 single-slotted flap at high angle of attack and close to maximum lift. The flow remained attached over the main element while a large region of recirculating flow occurred over the aft 61 percent of the flap. The airfoil configuration was tested at a Mach number of 0.09 and chord based Reynolds number of 1.8 x 10 to the 6th in the NASA Ames Research Center 7- by 10-Foot Wind Tunnel. Measurements of mean and fluctuating velocities were obtained in the region of recirculation and high turbulence intensity using three-dimensional laser velocimetry. In regions where the flow had a preferred direction and relatively low turbulence intensity hot-wire anemometry was used. Emphasis was placed on obtaining flow characteristics in the confluent boundary layer, the region of recirculating flow and in the downstream wake. Surface pressure measurements were made on the main airfoil, flap, wind tunnel roof, and wind tunnel floor. In addition to the presentation of pressure and velocity characteristics, the near wall results inside the separated region are analyzed as are the relative importance of terms in the momentum and turbulence kinetic energy equations in the confluent separated boundary layer and the recirculating region of the near wake.

Adair, Desmond↗
NASA NTRS1988

The distribution of vorticity in a large vortical motion

An experimental investigation into the distribution of vorticity in the large scale vortical motions which are found in free shear layers was undertaken. Using hot-wire anemometry, both quasi-instantaneous and phase averaged transverse vorticity were acquired. These results appear to indicate that the transverse vorticity in a large scale vortical motion is distributed in a marble cake manner and not in laminated sheets spooled up into a coil or helical spring. Also, levels of vorticity were found to vary by as much as an order of magnitude in these concentrated vortical cores.

Disimile, Peter J.↗
NASA NTRS1987

Basic aerodynamic research facility for comparative studies of flow diagnostic techniques

Current flow diagnostic research efforts are focusing on higher order flow field data bases, such as those generated by laser velocimetry (LV), hot-wire anemometry, and multi-hole pressure probes. Recent low-speed comparisons of results obtained with LV and hot wires have revealed strengths and weaknesses of each instrument. A seeding study will be initiated to determine particulate tracking ability.

Jones, Gregory S.↗
NASA NTRS1959

Performance of Typical Rear-Stage Axial-Flow Compressor Rotor Blade Row at Three Different Blade Setting Angles

A comparison of the performance of a single-stage rotor run at three different blade setting angles is presented. The rotor was of a design typical for a last stage of a multistage compressor. At each setting angle, the rotor blade row was operated from 53 to 100 percent of equivalent maximum speed (850 ft/sec tip speed) at constant inlet pressure. Hot-wire anemometry was used to observe rotating-stall and surge patterns in time unsteady flow. Results indicated that an increase in peak pressure ratio and an increase in maximum equivalent weight flow were obtained at each speed investigated when the blade setting angle was decreased. An increase in peak efficiency was achieved with decrease in blade setting angle for part of the range of speeds investigated. However, the peak efficiencies for the three blade setting angles were approximately the same at the maximum speed investigated. The flow ranges for all three configurations were about the same at minimum speed and decreased at almost the same rate when the rotative speed was increased through part of the range of speeds investigated. At maximum speed, the flow range for the smallest setting angle was considerably less than the flow range for the other two configurations. A decrease in efficiency and flow range for the smallest blade setting angle at maximum speed can be attributed primarily to a Mach number effect. In addition, because of the difference in projected axial chord lengths at the casing wall, some effect on performance could be expected from the change in three-dimensional flow occurring at the tip. Rotating-stall characteristics for the two smaller blade setting angles were essentially the same. Only surge could be detected for the largest blade setting angle in the unstable-flow region of operation.

Kussoy, Marvin I.↗
NASA NTRS1980

Conditional sampling technique to test the applicability of the Taylor hypothesis for the large-scale coherent structures

Comparisons of the distributions of large scale structures in turbulent flow with distributions based on time dependent signals from stationary probes and the Taylor hypothesis are presented. The study investigated an area in the near field of a 7.62 cm circular air jet at a Re of 32,000, specifically having coherent structures through small-amplitude controlled excitation and stable vortex pairing in the jet column mode. Hot-wire and X-wire anemometry were employed to establish phase averaged spatial distributions of longitudinal and lateral velocities, coherent Reynolds stress and vorticity, background turbulent intensities, streamlines and pseudo-stream functions. The Taylor hypothesis was used to calculate spatial distributions of the phase-averaged properties, with results indicating that the usage of the local time-average velocity or streamwise velocity produces large distortions.

Hussain, A. K. M. F.↗