Search NASA⌕ Search

SEARCH · Search NASA

Results for “hydrogen oxidation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Analytical methods for toxic gases from thermal degradation of polymers

Toxic gases evolved from the thermal oxidative degradation of synthetic or natural polymers in small laboratory chambers or in large scale fire tests are measured by several different analytical methods. Gas detector tubes are used for fast on-site detection of suspect toxic gases. The infrared spectroscopic method is an excellent qualitative and quantitative analysis for some toxic gases. Permanent gases such as carbon monoxide, carbon dioxide, methane and ethylene, can be quantitatively determined by gas chromatography. Highly toxic and corrosive gases such as nitrogen oxides, hydrogen cyanide, hydrogen fluoride, hydrogen chloride and sulfur dioxide should be passed into a scrubbing solution for subsequent analysis by either specific ion electrodes or spectrophotometric methods. Low-concentration toxic organic vapors can be concentrated in a cold trap and then analyzed by gas chromatography and mass spectrometry. The limitations of different methods are discussed.

Hsu, M.-T. S.↗
NASA NTRS1980

Preparation and evaluation of advanced electrocatalysts for phosphoric acid fuel cells

Alloy electrocatalysts on carbon supports were developed for hydrogen oxidation in the presence of carbon monoxide. These electrocatalysts match the best platinum on carbon catalysts for performance yet cost half as much. The results demonstrate that a significant reduction in anode electrocatalyst material cost can be achieved by replacing the platinum. Since surface characterization of this catalyst is important to explain its performance, several approaches and pitfalls to the elucidation of the surface characterization are presented.

Stonehart, P.↗
NASA NTRS1980

Non-noble catalysts and catalyst supports for phosphoric acid fuel cells

Tungsten carbide, which is known to be active for hydrogen oxidation and CO tolerant has a hexagonal structure. Titanium carbide is inactive and has a cubic structure. Four different samples of the cubic alloys Wx-1TixC were prepared and found to be active and CO tolerant. These alloys are of interest as possible phosphoric acid fuel cell catalysts. They also are of interest as opportunities to study the activity of W in a different crystalline environment and to correlate the activities of the surface sites with surface composition.

Mcalister, A. J.↗
NASA NTRS1981

Non-noble catalysts and catalyst supports for phosphoric acid fuel cells

Tungsten carbide, which is active for hydrogen oxidation, is CO tolerant and has a hexagonal structure is discussed. Titanium carbide is inactive and has a cubic structure. Four different samples of the cubic alloys W sub x-1Ti sub XC sub 1-y were found to be active and CO tolerant. When the activities of these cubic alloys are weighted by the reciprocal of the square to those of highly forms of WC. They offer important insight into the nature of the active sites on W-C anode catalysts for use in phosphoric acid fuel cells.

Mcalister, A. J.↗
NASA NTRS1982

The photochemistry of the paleoatmosphere

Recent progress in the understanding of the chemistry and photochemistry of the paleoatmosphere is reviewed with emphasis on the application of photochemical models to the investigation of the evolution of the atmosphere. Photochemical calculations are presented which show that a primordial highly reducing atmosphere composed of methane and ammonia, if it formed at all, would be short-lived in the presence of solar ultraviolet radiation, giving way rapidly to a more mildly reducing atmosphere of carbon dioxide and nitrogen. Estimations of O2 produced from the photolysis of water vapor prior to the emergence of photosynthesis range from less than 10 to the -14th to 0.1 times the present atmospheric level, indicating the need for further research. A series of photochemical models of increasing complexity has been developed to study the evolution of atmospheric ozone taking into account reactions with O atoms, hydrogen oxides, nitrogen oxides, and chlorine as well as vertical transport, temperature and tropospheric chemistry so that the total content and vertical distribution of O3 may be determined for a specified level of paleoatmospheric O2.

Levine, J. S.↗
NASA NTRS1986

Design and performance of the halogen occultation experiment (HALOE) remote sensor

HALOE is an optical remote sensor that measures extinction of solar radiation caused by the earth's atmosphere in eight channels, ranging in wavelength from 2.5 to 10.1 microns. These measurements, which occur twice each satellite orbit during solar occultation, are inverted to yield vertical distributions of middle atmosphere ozone (O3), water vapor, nitrogen dioxide, nitric oxide, hydrogen fluoride, hydrogen chloride, and methane. A channel located in the 2.7 region is used to infer the tangent point pressure by measuring carbon dioxide absorption. The HALOE instrument consists of a two-axis gimbal system, telescope, spectral discrimination optics and a 12-bit data system. The gimbal system tracks the solar radiometric centroid in the azimuthal plane and tracks the solar limb in the elevation plane, placing the instrument's instantaneous field-of-view 4 arcmin down from the solar top edge. The instrument gathers data for tangent altitudes ranging from 150 km to the earth's horizon. Prior to an orbital sunset and after an orbital sunrise, HALOE automatically performs calibration sequences to enhance data interpretation. The instrument is presently being tested at the NASA Langley Research Center in preparation for launch on the Upper Atmosphere Research Satellite near the end of this decade. This paper describes the instrumenmt design, operation, and functional performance.

Baker, R. L.↗
NASA NTRS1987

SAFIRE - A novel high resolution cooled spectrometer for atmospheric research

The SAFIRE (Spectroscopy of Atmospheric Far Infra-Red Emissions) experiment is discussed with particular reference to the scientific aims and the conceptual instrument design of the project. The principal requirements of the experiment are reviewed, and it is shown how these requirements are met in the instrument concept. In particular, measurements of hydrogen oxides and other important species in the stratosphere require a far infrared limb sounder. Some problems involved in the optical and thermal design of the instrument are examined.

Harries, J. E.↗
NASA NTRS1985

A field gas chromatograph using technology developed for solar system exploration

Trace gas analysis is an integral part of biospheric studies. Analytical instruments, primarily gas chromatographs (GC), are capable of measuring gases and volatiles to the ppb-level in real time. Trace gases significant in the study of biocycles include nitrous oxide, hydrogen sulfide, other nitrogen and sulfur species, as well as methane and ethylene. The concept of a field gas chromatograph is derived from technology being pursued in the design of ultra-compact instruments for solar system exploration. The instrument breadboard incorporates the specialized porous column packings and the highly sensitive metastable ionization detector developed by the Solar System Exploration Office. These parts ensure a broad capability for which the analysis of ambient N2O is one example. A commercial, portable gas chromatograph is currently being extensively modified to incorporate analytical concepts and components derived from flight GC technology. Data storage devices suitable for field use are presently being studied.

Woeller, F. H.↗
NASA NTRS1997

Adaptation of an In Situ Ground-Based Tropospheric OH/HO2 Instrument for Aircraft Use

In-situ HO(x) (OH and HO2) measurements are an essential part of understanding the photochemistry of aircraft exhaust in the atmosphere. HO(x) affects the partitioning of nitrogen species in the NO(y) family. Its reactions are important sources and sinks for tropospheric ozone, thus providing a link between the NO(x) in aircraft exhaust and tropospheric ozone. OH mixing ratios are enhanced in aircraft wakes due to the photolysis of the HONO that is made close to the engine. Measurements of HO(x) in aircraft wakes, along with NO(x) measurements, thus provides a constraint on chemical models of the engine combustion and exhaust. The development of the Airborne Tropospheric Hydrogen Oxides Sensor (ATHOS) is reported. We designed, developed, and successfully flew this instrument. It was part of the instrument complement on board the NASA DC-8 during SUCCESS, which took place in Kansas in April and May, 1996. ATHOS has a limit-of-detection for OH (S/N = 2) of 10(exp 5) OH molecules cm(exp -3) in less than 150 seconds. While this sensitivity is about 2-3 times less than the initial projections in the proposal, it is more than adequate for good measurements of OH and HO2 from the planetary boundary layer to the stratosphere. Our participation in SUCCESS was to be engineering test flights for ATHOS; however, the high-quality measurements we obtained are being used to study HO(x) photochemistry in contrails, clouds, and the clear air.

Brune, William H.↗
NASA NTRS2008

HOx Observation and Model Comparison During INTEX-A 2004

OH and HO2 were measured with the Airborne Tropospheric Hydrogen Oxides Sensor (ATHOS) as part of a large measurement suite from the NASA DC-8 aircraft during the Intercontinental Chemical Transport Experiment - A (INTEX-A). This mission, which was conducted mainly over North America and the western Atlantic Ocean in summer 2004, was an excellent test of atmospheric oxidation chemistry. Throughout the troposphere, observed OH was generally 0.60 of the modeled OH; below 8 km, observed HO2 was generally 0.78 of modeled HO2. If the over-prediction of tropospheric OH is not due to an instrument calibration error, then it implied less global tropospheric oxidation capacity and longer lifetimes for gases like methane and methyl chloroform than currently thought. This discrepancy falls well outside uncertainties in both the OH measurement and rate coefficients for known reactions and points to a large unknown OH loss. If the modeled OH is forced to agree with observed values by introducing of an undefined OH loss that removed HOx (HOx=OH+HO2), the observed and modeled HO2 and HO2/OH ratios are largely reconciled within the measurement uncertainty. HO2 behavior above 8 km was markedly different. The observed-to-modeled ratio correlating with NO. The observed-to-modeled HO2 ratio increased from approximately 1 at 8 km to more than approximately 2.5 at 11 km with the observed-to-modeled ratio correlating with NO. The observed-to-modeled HO2 and NO were both considerably greater than observations from previous campaigns. In addition, the observed-to-modeled HO2/OH, which is sensitive to cycling reactions between OH and HO2, increased from approximately 1.2 at 8 km to almost 4 above 11 km. In contrast to the lower atmosphere, these discrepancies above 8 km suggest a large unknown HOx source and additional reactants that cycle HOx from OH to HO2. In the continental planetary boundary layer, the OH observed-to-modeled ratio increased from 0.6 when isoprene was less than 0.1 ppbv to over 3 when isoprene was greater than 2 ppbv, suggesting that forests throughout the United States are emitting unknown HOx sources. Progress in resolving these discrepancies requires further examinations of possible unknown OH sinks and HOx sources and a focused research activity devoted to ascertaining the accuracy of the OH and HO2 measurements.

Ren, Xinrong↗
NASA NTRS2013

Aerospace Fuels From Nonpetroleum Raw Materials

Recycling human metabolic and plastic wastes minimizes cost and increases efficiency by reducing the need to transport consumables and return trash, respectively, from orbit to support a space station crew. If the much larger costs of transporting consumables to the Moon and beyond are taken into account, developing waste recycling technologies becomes imperative and possibly mission enabling. Reduction of terrestrial waste streams while producing energy and/or valuable raw materials is an opportunity being realized by a new generation of visionary entrepreneurs; several relevant technologies are briefly compared, contrasted and assessed for space applications. A two-step approach to nonpetroleum raw materials utilization is presented; the first step involves production of supply or producer gas. This is akin to synthesis gas containing carbon oxides, hydrogen, and simple hydrocarbons. The second step involves production of fuel via the Sabatier process, a methanation reaction, or another gas-to-liquid technology, typically Fischer-Tropsch processing. Optimization to enhance the fraction of product stream relevant to transportation fuels via catalytic (process) development at NASA Glenn Research Center is described. Energy utilization is a concern for production of fuels whether for operation on the lunar or Martian surface, or beyond. The term green relates to not only mitigating excess carbon release but also to the efficiency of energy usage. For space, energy usage can be an essential concern. Another issue of great concern is minimizing impurities in the product stream(s), especially those that are potential health risks and/or could degrade operations through catalyst poisoning or equipment damage; technologies being developed to remove heteroatom impurities are discussed. Alternative technologies to utilize waste fluids, such as a propulsion option called the resistojet, are discussed. The resistojet is an electric propulsion technology with a powered thruster to vaporize and heat a propellant to high temperature, hot gases are subsequently passed through a converging-diverging nozzle expanding gases to supersonic velocities. A resistojet can accommodate many different fluids, including various reaction chamber (by-)products.

Palaszewski, Bryan A.↗
NASA NTRS2013

Aerospace Fuels from Nonpetroleum Raw Materials

Recycling human metabolic and plastic wastes minimizes cost and increases efficiency by reducing the need to transport consumables and return trash, respectively, from orbit to support a space station crew. If the much larger costs of transporting consumables to the Moon and beyond are taken into account, developing waste recycling technologies becomes imperative and possibly mission enabling. Reduction of terrestrial waste streams while producing energy and/or valuable raw materials is an opportunity being realized by a new generation of visionary entrepreneurs; several relevant technologies are briefly compared, contrasted and assessed for space applications. A two-step approach to nonpetroleum raw materials utilization is presented; the first step involves production of supply or producer gas. This is akin to synthesis gas containing carbon oxides, hydrogen, and simple hydrocarbons. The second step involves production of fuel via the Sabatier process, a methanation reaction, or another gas-to-liquid technology, typically Fischer- Tropsch processing. Optimization to enhance the fraction of product stream relevant to transportation fuels via catalytic (process) development at NASA GRC is described. Energy utilization is a concern for production of fuels whether for operation on the lunar or Martian surface, or beyond. The term "green" relates to not only mitigating excess carbon release but also to the efficiency of energy usage. For space, energy usage can be an essential concern. Other issues of great concern include minimizing impurities in the product stream(s), especially those that are potential health risks and/or could de-grade operations through catalyst poisoning or equipment damage; technologies being developed to remove heteroatom impurities are discussed. Alternative technologies to utilize waste fluids, such as a propulsion option called the resistojet, are discussed. The resistojet is an electric propulsion technology with a powered thruster to vaporize and heat a propellant to high temperature, hot gases are subsequently passed through a converging-diverging nozzle expanding gases to supersonic velocities. A resistojet can accommodate many different fluids, including various reaction chamber (by-)products.

Palaszewski, B. A.↗
NASA NTRS2018

Interstellar Ices and Radiation-Induced Oxidations of Alcohols

Infrared spectra of ices containing alcohols that are known or potential interstellar molecules are examined before and after irradiation with 1 MeV protons at ~20 K. The low-temperature oxidation (hydrogen loss) of six alcohols is followed, and conclusions are drawn based on the results. The formation of reaction products is discussed in terms of the literature on the radiation chemistry of alcohols and a systematic variation in their structures. The results from these new laboratory measurements are then applied to a recent study of propargyl alcohol. Connections are drawn between known interstellar molecules, and several new reaction products in interstellar ices are predicted.

astrochemistry – infrared: ISM – ISM: molecule↗
NASA NTRS2018

Interstellar Ices and Radiation-induced Oxidations of Alcohols

Infrared spectra of ices containing alcohols that are known or potential interstellar molecules are examined before and after irradiation with 1 MeV protons at ~20 K. The low-temperature oxidation (hydrogen loss) of six alcohols is followed, and conclusions are drawn based on the results. The formation of reaction products is discussed in terms of the literature on the radiation chemistry of alcohols and a systematic variation in their structures. The results from these new laboratory measurements are then applied to a recent study of propargyl alcohol. Connections are drawn between known interstellar molecules, and several new reaction products in interstellar ices are predicted.

astrochemistry – infrared: ISM – ISM: molecule↗
NASA NTRS2018

Interstellar Ices and Radiation-Induced Oxidations of Alcohols

Infrared spectra of ices containing alcohols that are known or potential interstellar molecules are examined before and after irradiation with 1 MeV protons at ~20 K. The low-temperature oxidation (hydrogen loss) of six alcohols is followed, and conclusions are drawn based on the results. The formation of reaction products is discussed in terms of the literature on the radiation chemistry of alcohols and a systematic variation in their structures. The results from these new laboratory measurements are then applied to a recent study of propargyl alcohol. Connections are drawn between known interstellar molecules, and several new reaction products in interstellar ices are predicted.

astrochemistry – infrared: ISM – ISM: molecules – ↗
NASA NTRS1981

Effect of oxide films on hydrogen permeability of candidate Stirling engine heater head tube alloys

The effect of oxide films developed in situ from CO/CO2 doped hydrogen on high pressure hydrogen permeability at 820 C was studied on N-155, A-286, IN 800, 19-9DL, Nitronic 40, HS-188, and IN 718 tubing in a Stirling materials simulator. The hydrogen permeability decreased with increasing dopant levels of CO or CO2 and corresponding decreases in oxide porosity. Minor reactive alloying elements strongly influenced permeability. At high levels of CO or CO2, a liquid oxide formed on alloys with greater than 50 percent Fe. This caused increased permeability. The oxides formed on the inside tube walls were analyzed and their effective permeabilities were calculated.

Schuon, S. R.↗
NASA NTRS1988

The role of molecular hydrogen and methane oxidation in the water vapour budget of the stratosphere

The detailed photochemistry of methane oxidation has been studied in a coupled chemical/dynamical model of the middle atmosphere. The photochemistry of formaldehyde plays an important role in determining the production of water vapor from methane oxidation. At high latitudes, the production and transport of molecular hydrogen is particularly important in determining the water vapor distribution. It is shown that the ratio of the methane vertical gradient to the water vapor vertical gradient at any particular latitude should not be expected to be precisely 2, due both to photochemical and dynamical effects. Modeled H2O profiles are compared with measurements from the Limb Infrared Monitor of the Stratosphere (LIMS) experiment at various latitudes. Molecular hydrogen is shown to be responsible for the formation of a secondary maximum displayed by the model water vapor profiles in high latitude summer, a feature also found in the LIMS data.

Le Texier, H.↗
NASA NTRS1973

International Symposium on Combustion, 14th, Pennsylvania State University, University Park, Pa., August 20-25, 1972, Proceedings.

Some elementary steps for the formation and destruction of nitric oxide in the H-N-O system, high-temperature oxidation of hydrogen by nitrous oxide in shock waves, and high-temperature fast-flow reactor studies of metal-atom oxidation kinetics are among the topics covered in papers concerned with elementary reactions in combustion. Other areas covered include oscillatory, turbulent, and supersonic combustion; flames in furnaces and combustors; and pollutant formation and destruction in flames. Individual items are announced in this issue.

Source record↗