SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Technique for visualization of three-dimensional flow uses tiny tracer bubbles of hydrogen and oxygen made by electrolysis of water. Strobe-light photography used to capture flow patterns, yielding permanent record that is measured to obtain velocities of particles. Used to measure simulated mixing turbulence in proposed gas-turbine combustor and also used in other water-table flow tests.
Two flow visualization techniques, i.e., simultaneous two-dimensional fluorescence imaging of H2 and O2 in a diffusion flame, and quasi-linear fluorescence imaging of O2, are presented. The first uses an injection-locked argon-fluoride excimer laser and a partial overlap of a two-photon ground state absorption in H2 with a single photon absorption from a vibrational level in O2. The second uses a simple, high-intensity ultraviolet flashlamp which provides a flux of photons in the 180-195 nm range, sufficient to produce a quasi-one-dimensional fluorescence image of hot/room temperature oxygen. Both techniques do not require that a seed material be introduced into the flow, they can image major flow constituents, and provide an instantaneous snapshot of the flow.
In order to investigate the atmospheric shock dynamics of Miras, a program to monitor the ultraviolet Mg II flux, the visual magnitude (using the IUE FES-magnitude) and whenever possible the hydrogen Balmer emission for several Miras was initiated. Results suggest that it should be possible to derive the density structure of the atmosphere and hence estimate quite accurately the kinetic energy input into the stellar atmosphere. The atmospheric shock models suggest that at phase equal 1.0 most of the energy which enters the region where the shock is located ends up in the wind. This is after the strongest Mg II emission is seen. From an observed velocity at infinity and an estimate of the energy input derived from the Mg II flux, it will be possible to determine the mass loss rate for these objects.
Low surface brightness photometry of the intergalactic neutral hydrogen cloud in Leo sets upper limits on the intensity of this object of 28.0 mag/sq arcsec in the V photometric band and 22.8 mag/sq arcsec in the K band. The corresponding ratio of the H I mass to blue luminosity in the H I emission peaks of the cloud must be greater than 2.9 (solar units) depending on the star formation history of the object. The limits imposed on the star formation rate suggest a strong dependence of this rate on gas density.
Flux measurements at 1.6, 2.2, and 3.4 microns for 42 stars in the young cluster NGC 2264 suggest that a significant number of these stars are surrounded by circumstellar material which produces observable infrared excesses. Hydrogen line profiles are used to estimate surface gravities and thereby to predict visual luminosities for a number of pre-main-sequence A stars. Those stars which appear faintest as compared with their predicted luminosities all have infrared excesses.
Recent advances in spectroscopic studies of the planets with ground-based telescopes in the photomultiplier and IR spectral ranges are reviewed. Results of spectroscopic observations of Venus and Mars are briefly summarized, noting that the crucial problem confronting the interpretation of the Venusian spectrum is the nature of the clouds and that the outstanding problem in understanding the Martian atmosphere is the N2 or Ar concentration that may be present. Spectroscopic results for Jupiter, Saturn, Uranus, and Neptune are discussed, emphasizing observations of molecular hydrogen, HD, water, (C-13)H4, other hydrocarbons, and deuterated hydrocarbons. IR and visual spectroscopic observations of Titan and Io are reviewed which show that the CH4 bands in Titan's spectrum are pressure broadened and that a flattened ring of sodium is situated around Jupiter in the orbital plane of Io.
Drop tower experiments were performed to identify buoyancy effects in transitional hydrogen gas jet diffusion flames. Quantitative rainbow schlieren deflectometry was utilized to optically visualize the flame and to measure oxygen concentration in the laminar portion of the flame. Test conditions consisted of atmospheric pressure flames burning in quiescent air. Fuel from a 0.3mm inside diameter tube injector was issued at jet exit Reynolds numbers (Re) of 1300 to 1700. Helium mole percentage in the fuel was varied from 0 to 40%. Significant effects of buoyancy were observed in near field of the flame even-though the fuel jets were momentum-dominated. Results show an increase of breakpoint length in microgravity. Data suggest that transitional flames in earth-gravity at Re<1300 might become laminar in microgravity.
The current work compares experimentally and computationally obtained nitric oxide (NO) planar laser induced fluorescence (PLIF) images of the mixing flowfields for three types of high-speed fuel injectors: a strut, a ramp, and a rectangular flushwall. These injection devices, which exhibited promising mixing performance at lower flight Mach numbers, are currently being studied as a part of the Enhanced Injection and Mixing Project (EIMP) at the NASA Langley Research Center. The EIMP aims to investigate scramjet fuel injection and mixing physics, and improve the understanding of underlying physical processes relevant to flight Mach numbers greater than eight. In the experiments, conducted in the NASA Langley Arc-Heated Scramjet Test Facility (AHSTF), the injectors are placed downstream of a Mach 6 facility nozzle, which simulates the high Mach number air flow at the entrance of a scramjet combustor. Helium is used as an inert substitute for hydrogen fuel. Both schlieren and PLIF techniques are applied to obtain mixing flowfield flow visualizations. The experimental PLIF is obtained by using a UV laser sheet to interrogate a plane of the flow by exciting fluorescence from the NO molecules, which are present in the AHSTF air. Consequently, the absence of signal in the resulting PLIF images is an indication of pure helium (fuel). The computational PLIF is obtained by applying a fluorescence model for NO to the results of the Reynolds-averaged simulations (RAS) of the mixing flow field carried out using the VULCAN-CFD solver. This approach is required because the PLIF signal is a nonlinear function of not only NO concentration, but also pressure, temperature, and the flow velocity. This complexity allows additional flow features to be identified and compared with those obtained from the computational fluid dynamics (CFD) simulations, however, such comparisons are only semiquantitative. Three-dimensional image reconstruction, similar to that used in magnetic resonance imaging, is also used to obtain images in the streamwise and spanwise planes from select cross-stream PLIF plane data. Synthetic schlieren is also computed from the RAS data. Good agreement between the experimental and computational results provides increased confidence in the CFD simulations for investigations of injector performance.
The current work compares experimentally and computationally obtained nitric oxide (NO) planar laser-induced fluorescence (PLIF) images of the mixing flowfields for three types of high-speed fuel injectors: a strut, a ramp, and a rectangular flushwall. These injection devices, which exhibited promising mixing performance at lower flight Mach numbers, are currently being studied as a part of the Enhanced Injection and Mixing Project (EIMP) at the NASA Langley Research Center. The EIMP aims to investigate scramjet fuel injection and mixing physics, and improve the understanding of underlying physical processes relevant to flight Mach numbers greater than eight. In the experiments conducted in the NASA Langley Arc-Heated Scramjet Test Facility (AHSTF), the injectors are placed downstream of a Mach 6 facility nozzle, which simulates the high Mach number air flow at the entrance of a scramjet combustor. Helium is used as an inert substitute for hydrogen fuel. Both schlieren and PLIF techniques are applied to obtain mixing flowfield flow visualizations. The experimental PLIF is obtained by using a UV laser sheet to interrogate a plane of the flow by exciting fluorescence from the NO molecules that are present in the AHSTF air. Consequently, the absence of signal in the resulting PLIF images is an indication of pure helium (fuel). The computational PLIF is obtained by applying a fluorescence model for NO to the results of the Reynolds-averaged simulations (RAS) of the mixing flowfield carried out using the VULCAN-CFD solver. This approach is required because the PLIF signal is a nonlinear function of not only NO concentration, but also pressure, temperature, and the flow velocity. This complexity allows additional flow features to be identified and compared with those obtained from the computational fluid dynamics (CFD) simulations, however, such comparisons are only semiquantitative. Three-dimensional image reconstruction, similar to that used in magnetic resonance imaging, is also used to obtain images in the streamwise and spanwise planes from select cross-stream PLIF plane data. Synthetic schlieren is also computed from the RAS data. Good agreement between the experimental and computational results provides increased confidence in the CFD simulations for investigations of injector performance.
The current work compares experimentally and computationally obtained nitric oxide (NO) planar laser-induced fluorescence (PLIF) images of the mixing flowfields for three types of high-speed fuel injectors: a strut, a ramp, and a rectangular flushwall. These injection devices, which exhibited promising mixing performance at lower flight Mach numbers, are currently being studied as a part of the Enhanced Injection and Mixing Project (EIMP) at the NASA Langley Research Center. The EIMP aims to investigate scramjet fuel injection and mixing physics, and improve the understanding of underlying physical processes relevant to flight Mach numbers greater than eight. In the experiments conducted in the NASA Langley Arc-Heated Scramjet Test Facility (AHSTF), the injectors are placed downstream of a Mach 6 facility nozzle, which simulates the high Mach number air flow at the entrance of a scramjet combustor. Helium is used as an inert substitute for hydrogen fuel. Both schlieren and PLIF techniques are applied to obtain mixing flowfield flow visualizations. The experimental PLIF is obtained by using a UV laser sheet to interrogate a plane of the flow by exciting fluorescence from the NO molecules that are present in the AHSTF air. Consequently, the absence of signal in the resulting PLIF images is an indication of pure helium (fuel). The computational PLIF is obtained by applying a fluorescence model for NO to the results of the Reynolds-averaged simulations (RAS) of the mixing flowfield carried out using the VULCAN-CFD solver. This approach is required because the PLIF signal is a nonlinear function of not only NO concentration, but also pressure, temperature, and the flow velocity. This complexity allows additional flow features to be identified and compared with those obtained from the computational fluid dynamics (CFD) simulations, however, such comparisons are only semiquantitative. Three-dimensional image reconstruction, similar to that used in magnetic resonance imaging, is also used to obtain images in the streamwise and spanwise planes from select cross-stream PLIF plane data. Synthetic schlieren is also computed from the RAS data. Good agreement between the experimental and computational results provides increased confidence in the CFD simulations for investigations of injector performance.
LTE (C-13)O column densities are compared with the corresponding values of beam-convolved visual extinction at more than 100 locations within 38 different interstellar dark clouds. A roughly linear correlation is found to exist between these two quantities for visual extinctions in the range from about 1.5 to 5 mag. It is argued that this correlation can be extended up to about 10 mag and that the standard gas-to-extinction ratio can be expected to remain valid in the sources studied. The correlation of LTE (C-13)O column density with visual extinction is used to obtain an equation for the H2 column density associated with a given (C-13)O column density. It is shown that if the clouds studied are assumed to be chemically homogeneous, the equation obtained implies that at least 12% of all gas-phase carbon is in the form of CO. Comparison of the observational data with various theories proposed for molecule formation in dark clouds indicates that Langer's (1977) ion-molecule scheme accounts well for the observations when the fractionation channel of Watson et al. (1976) is included.
After propellant was loaded into the external tank (ET), the November 5, 2010 launch of Space Shuttle mission STS-133 was scrubbed due to a gaseous hydrogen leak located in a vent line near the ground umbilical and ET connection. Subsequent visual inspections identified cracks in the sprayed-on foam insulation in the forward end of the ET intertank segment, adjacent to the liquid oxygen (LOX) tank, as shown in Figure 1. These cracks necessitated repair of the foam due to debris concerns that violated launch constraints. As part of the repair process, the affected foam was removed to reveal cracks in the underlying external hat stiffeners on the intertank, as shown in Figure 2. Ultimately, five stiffeners were discovered to be cracked adjacent to the LOX tank. As the managing center for the ET Project, NASA Marshall Space Flight Center (MSFC) coordinated failure investigation and repair activities among multiple organizations, which included the ET prime contractor (Lockheed Martin Space Systems Michoud Operations), the Space Shuttle Program Office at the NASA Johnson Space Center (JSC), the NASA Kennedy Space Center (KSC), and the NASA Engineering and Safety Center (NESC). STS-133 utilized the external tank designated as ET-137. Many aspects of the investigation have been reported previously in Refs. 1-7, which focus on the root cause of the failures, the flight readiness rationale and the local analyses of the stringer failures and repair. This paper summarizes the global analyses that were conducted on ET-137 as part of the NESC effort during the investigation, which was conducted primarily to determine if the repairs that were introduced to the stringers would alter the global response of the ET. In the process of the investigation, a new STAGS tabular input capability was developed to more easily introduce the aerodynamic pressure loads using a method that could easily be extended to incorporate finite element property data such as skin and stiffener thicknesses and beam cross-sectional properties.
Observations with IUE that cover the entire 6.4 hr orbital cycle of the late-type contact binary 44i Bootis are presented. Intrinsic stellar hydrogen Lyman alpha emission flux was determined from low-resolution IUE spectra, compensating for geocoronal emission and for interstellar absorption. The variation of the stellar Lyman alpha emission flux correlates well with the variation of the CII and CIV emission fluxes, and shows orbital modulation in phase with the visual light curve. The ratio of Lyman alpha to CII flux (15 to 20) is similar to that observed in solar active regions. Hydrogen Lyman alpha emission is thus one of the most important cooling channels in the outer atmosphere of 44i Boo. A high-resolution spectrum of the Lyman alpha line was obtained between orbital phases 0.0 and 0.6. The integrated flux in the observed high-resolution Lyman alpha profile is consistent with the fluxes determined using low-resolution spectra, and the composite profile indicates that both components of this binary have equally active chromospheres and transition regions. The uncertainty in the interstellar hydrogen column density cannot mimic the observed variation in the integrated Lyman alpha flux, because the stellar line is very much broader than the interstellar absorption.
Observations with IUE that cover the entire 6.4 hr orbital cycle of the late-type contact binary 44i Bootis are presented. Intrinsic stellar hydrogen Lyman alpha emission flux was determined from low-resolution IUE spectra, compensating for geocoronal emission and for interstellar absorption. The variation of the stellar Lyman alpha emission flux correlates well with the variation of the C II and C IV emission fluxes, and shows orbital modulation in phase with the visual light curve. The ratio of Lyman alpha to CII flux (15 to 20) is similar to that observed in solar active regions. Hydrogen Lyman alpha emission is thus one of the most important cooling channels in the outer atmosphere of 44i Boo. A high-resolution spectrum of the Lyman alpha line was obtained between orbital phases 0.0 and 0.6. The integrated flux in the observed high-resolution Lyman alpha profile is consistent with the fluxes determined using low-resolution spectra, and the composite profile indicates that both components of this binary have equally active chromospheres and transition regions. The uncertainty in the interstellar hydrogen column density cannot mimic the observed variation in the integrated Lyman alpha flux, because the stellar line is very much broader than the interstellar absorption.
Ground-based infrared observations of the K3-50 region are reported at wavelengths between 2 and 34 microns as well as at 1 mm. The main results are that (1) the visible nebular K3-50 is displaced from its infrared and radio counterparts; (2) component Cl (the OH source ON-3) appears very faint at wavelengths not exceeding 20 microns and is therefore probably obscured by several hundred magnitudes of visual extinction; (3) both K3-50 and component C are associated with separate condensations of molecular hydrogen, each of about 3000 solar masses; and (4) there are no strong sources in this region at 20 microns other than those associated with H II condensations.
We have conducted an extensive analysis of the observability of Classical Novae with the EUVE Lex/B and Al/Ti/C detectors. Predicted count rates have been computed using optically thin, isothermal plasma models for solar and metal-rich compositions, and hot ONeMg white dwarf model atmospheres. We find EUVE to be quite sensitive to both the EUV and soft X-ray emission emitted by the underlying hot white dwarf during novae outbursts, except for the coolest temperatures with very high intervening hydrogen column density. These results are used to interpret the emission detected during the EUVE all-sky survey of Nova Cygni 1992 (approx. = V1974 Cyg), 279-290 days after visual maximum. We find the best fit to the observed emission from V1974 Cyg arises from a hot ONeMg white dwarf with surface temperature approx. 4 x l0(exp 5) K and a mas of approx. 1.2 solar mass, and derive an interstellar hydrogen column density of approx. 3 x 10(exp 21)/sq cm. Virtually all this emission arises from supersoft X-rays rather than the EUV. We also report the detection of V1974 Cyg with the EUVE Deep Survey detector at 549 days after visual maximum. This observation is compatible with the above properties, indicating that the mechanism responsible for the soft X-ray emission, connected with the underlying white dwarf, had not yet entirely turned off. We also present analysis of a ROSAT PSPC observation which is contemporaneous with the EUVE survey observations; this independently confirms the high column density we derived from the EUVE survey observation. Light curves for the EUVE and ROSAT observations are presented. Statistical tests for variability show that all of these observations are indeed highly variable over various time scales. The EUVE survey data shows one day variations, the EUVE DS data show approx. 30 minute fluctuations, while the ROSAT data vary rapidly on time scales of seconds. The EUVE data shows no periodic variability on any time scale. The implications of the rapid variability are briefly discussed.
Preliminary data are presented covering the performance of a low-speed, five-cylinder piston pump designed for handling boiling hydrogen. This pump was designed for a flow of 55 gallons per minute at 240 rpm with a discharge pressure of 135 pounds per square inch. Tests were made using JP-4 fuel, liquid nitrogen, and liquid hydrogen. Pump delivery and endurance characteristics were satisfactory for the range of operation covered. In connection with the foregoing pump development, the cavitation characteristics of a preliminary visual model, glass-cylinder pump and of a simple reciprocating disk were studied. Subcooling of approximately 0.60 F was obtained from the cavitation produced by reciprocating a disk in boiling nitrogen and in boiling water. The subcooling obtained in a similar manner with liquid hydrogen was somewhat less.
Computational fluid dynamics (CFD) methods based on the Reynolds averaged Navier-Stokes (RANS) equations are extensively employed in the design of hypersonic airbreathing engines. A fundamental weakness in these methods is the accurate mathematical modeling of turbulence and turbulence-combustion interactions. This paper is one of a companion pair of papers which describe the use of the combined dual pump CARS and newly developed interferometric Rayleigh scattering optical system to acquire time-accurate turbulence and mixing data with which to aid calibration and verification of the current turbulence models. This test program consisted of a pilot laboratory-scale experiment used to develop the optical system and data acquisition techniques, and a significantly larger experiment to acquire the necessary turbulence data. The flow is an axially-symmetric, supersonic, combusting, free jet that provides good optical access, consisting of a central jet of hot "vitiated air" and a coflow jet of hydrogen or ethylene fuel. In this paper the development of both experiments is described. Facility and flow visualization data are presented for various types of flames, including the flames selected for detailed study with the CARS/Rayleigh optical techniques.