Search NASA⌕ Search

SEARCH · Search NASA

Results for “hydromechanics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Water-Weakening and Time-Dependent Deformation of Organic-Rich Chalks

Abstract The Ghareb Formation is a shallowly buried porous chalk in southern Israel that is being considered as a host rock for a geologic nuclear waste repository. Setup and operation of a repository will induce significant mechanical, hydrological and chemical perturbations in the Ghareb. Developing a secure repository requires careful characterization of the rock behavior to different loads. To characterize hydromechanical behavior of the Ghareb, several short- and long-term deformation experiments were conducted. Hydrostatic loading tests were conducted both dry and water-saturated, using different setups to measure elastic properties, time-dependent behavior, and permeability. A set of triaxial tests were conducted to measure the elastic properties and rock strength under differential loading at dry and water-saturated conditions. The hydrostatic tests showed the Ghareb began to deform inelastically around 12–15 MPa, a relatively low effective pressure. Long-term permeability measurements demonstrated that permeability declined with increasing effective pressure and was permanently reduced by ~ 1 order of magnitude after unloading pressure. Triaxial tests showed that water saturation significantly degrades the rock properties of the Ghareb, indicating water-weakening is a significant risk during repository operation. Time-dependent deformation is observed during hold periods of both the hydrostatic and triaxial tests, with deformation being primarily visco-plastic. The rate of deformation and permeability loss is strongly controlled by the effective pressure as well. Additionally, during holds of both hydrostatic and triaxial tests, it is observed that when water-saturated, radial strain surpassed axial strain when above effective pressures of 13–20 MPa. Thus, deformation anisotropy may occur in situ during operations even if the stress conditions are hydrostatic when above this pressure range.

58 GEOSCIENCES↗
DOE OSTI2023

Numerical Simulations of Flow-Induced Deflections in MITR LEU Fuel Plate Due to Channel Size Disparity

The hydromechanical stability of the fuel plates in parallel coolant channels of a Materials Testing Reactor (MTR) fuel element design is of great importance to the safety of research and test reactors. Previous analytical, experimental, and numerical efforts focused on parallel channels with the same or similar size; also, in the prior numerical simulations, the fuel plate was often assumed to be perfectly flat. This work presents the results of a fluid-structure interaction simulation performed to evaluate the flow-induced deflections of the fuel plates in the low-enriched uranium (LEU, <20 wt% 235 U) fuel element design for the conversion (from highly enriched uranium) of the Massachusetts Institute of Technology Reactor (MITR-II, also referred to as MITR). Various manufacturing and assembly tolerances of the MITR LEU elements are considered in the analysis, and the effects of channel size disparity, nonideal plate shape, and flow rate uncertainty are investigated. Results show that, for all cases analyzed, the deflection occurs toward the larger channel, and the change in any channel stripe remains small (less than 0.021 mm) compared to fabrication tolerances. In addition to simulation work, a hydraulic performance test of the MITR LEU fuel element is currently planned to support conversion to the use of LEU fuel.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Changes in rock matrix compressibility during deep CO 2 storage

Geologic carbon storage projects aim to permanently trap large volumes of CO 2 in reservoir rock sealed with low permeability layers. As high-pressure supercritical or liquid CO 2 is injected, hydromechanical and chemical processes caused by the reaction between the rock and acidic mixture of brine and CO 2 are initiated. The compressibility of reservoir rock needs to be properly characterized in order to assess the deformation and stability of the host formations, and there are a number of factors to be considered, including the matrix structure, solid, pores, and fluid. Here this study triggers from a fundamental question whether CO 2 treatment affects the compressibility of the rock matrix and its dominant composing solid minerals. Three different reservoir representatives are selected: Berea sandstone for silica-rich rock, and Apulian limestone and Indiana limestone for calcite-rich rock. Quartz and calcite are the main composing minerals of the reservoir rock, and their crystals are separately examined. Experimental methods are introduced for high-pressure CO 2 treatment of water-saturated materials, and measurements of the unjacketed and solid compressibilities are conducted. No change in the solid compressibility of the sandstone and quartz after CO 2 treatment is observed, whereas it increases by 18–21% for the limestones and by 15% for calcite. The latter observation is inconsistent with the ultrasonic wave velocities measurements and is believed to be due to the local dissolution of the calcite crystal surface. Our results show that only the solid matrix of the limestones becomes more compressible after CO 2 treatment. Consequent microimaging and mercury intrusion porosimetry analyses allowed observations of dissolution and precipitation of calcite, and creation of new connected and non-connected pores. Finally, the changes in limestone solid compressibilities and pore structure could significantly affect the rock properties and behavior during and after CO 2 injection and should be accounted for in the reservoir models.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Comparative Analysis of Imaging and Measurements of Micrometer-Scale Fracture Aperture Fields Within a Heterogeneous Rock Using PET and X-ray CT

Knowledge of the spatial distribution of fracture apertures is essential for reliable characterization of flow and transport processes in fractured systems and for better understanding of physicochemical matrix–fracture interactions. Here, we propose and test two image-based methods, thereby extending the current experimental capabilities to characterize aperture size distribution in structurally heterogeneous geologic porous media noninvasively. The first approach utilizes an inversion method based on the dataset acquired from positron emission tomography (PET) and the second approach considers an extension of the classic missing attenuation technique that relies on clinical X-ray computed tomography (X-ray CT). Independent sets of imaging experiments are conducted on a fractured basalt core with heterogeneous matrix properties and aperture distributions to compare the two methodologies. A repeat of each experiment is conducted to verify the proposed workflows. The performance of these two imaging techniques is systematically evaluated through the analysis of signal-to-noise ratio, minimum fracture size detectability, and measurement errors. While both approaches provide a reliable estimation of fracture aperture distributions, PET yields a signal-to-noise ratio that is substantially higher than the corresponding X-ray CT measurements. Furthermore, uncertainties of the aperture values for PET are considerably lower ($\bar {\sigma}_{\text {d}} = 15\%$) compared to those obtained from X-ray CT ($\bar {\sigma}_{\text {d}} = 29\%$), allowing for the detection of minimum aperture sizes of 20 $\mu$m with 70% confidence level. Finally, these approaches provide key experimental tools for better understanding dynamic hydromechanical fracture properties in geologic systems.

58 GEOSCIENCES↗
DOE OSTI2024

Crack opening calculation in phase-field modeling of fluid-filled fracture: A robust and efficient strain-based method

The phase-field method has become popular for the numerical modeling of fluid-filled fractures, thanks to its ability to represent complex fracture geometry without algorithms. However, the algorithm-free representation of fracture geometry poses a significant challenge in calculating the crack opening (aperture) of phase-field fracture, which governs the fracture permeability and hence the overall hydromechanical behavior. Although several approaches have been devised to compute the crack opening of phase-field fracture, they require a sophisticated algorithm for post-processing the phase-field values or an additional parameter sensitive to the element size and alignment. Here, we develop a novel method for calculating the crack opening of fluid-filled phase-field fracture, which enables one to obtain the crack opening without additional algorithms or parameters. Here we transform the displacement-jump-based kinematics of a fracture into a continuous strain-based version, insert it into a force balance equation on the fracture, and apply the phase-field approximation. Through this procedure, we obtain a simple equation for the crack opening which can be calculated with quantities at individual material points. We verify the proposed method with analytical and numerical solutions obtained based on discrete representations of fractures, demonstrating its capability to calculate the crack opening regardless of the element size or alignment.

58 GEOSCIENCES↗
DOE OSTI2022

Experimental study of fracture slip due to stress perturbation in fractured geo-resources

Anthropogenic activities such as underground fluid injection/extraction, well stimulation, and dam impoundment will perturb the state-of-stress in the subsurface, which could activate critically stressed pre-existing fractures and faults. Fault and fracture activation can induce seismicity, change flow behavior, and damage asperities on the fracture surface to alter reservoir permeability. Here, in this study, triaxial shear tests were conducted on saw cut and rough fracture Barre granite specimens to better characterize how a decrease in normal stress and increase in shear stress will influence crystalline rock fracture hydromechanical properties. In a triaxial set up, confining pressure (CP) and differential stress (DS) were used to induce normal and shear stress on a 45° oriented fracture. Fracture slip and the corresponding stress relaxation was observed when the confining stress decreased. Fracture permeability increased when the fracture slipped. Moreover, new micro-cracks observed by x-ray images indicated the creation of new flow paths for fluid movement. The experimental outcomes of this study indicate that decrease in normal stress due to stress perturbations along the faults/fractures in the extensional stress regime can induce the slip along the fracture. This could have a significant influence on slope stability in quarries, stimulation and injection strategy in deep geo-resources, and potentially minimize the risk of induced seismicity. The observed stress dependency of hydraulic aperture in rough fracture during pre- and post-slip stages could provide key inputs for field-scale simulation of geo-resources.

58 GEOSCIENCES↗
DOE OSTI2020

Determination of permeability for hydrocarbon release due to excavation-induced stress redistribution in rock salt

Due to a stress redistribution after the excavation of an underground tunnel for radioactive waste disposal, an Ed/DZ (excavation disturbed/damaged zone) will be generated in the near field of the opening, resulting in significant changes in the hydraulic and mechanical properties of the rock mass in the zone. Initially more or less randomly distributed hydrocarbons at grain boundaries in rock salt, which sometimes can only be observed with ultraviolet light, can then be mobilised and migrate at a potentially significant rate towards the excavation. Within the international cooperative project DECOVALEX 2019, the migration mechanism of such fluid inclusions in rock salt is being studied intensively. Specifically, a multi-scale modelling strategy has been developed. A macroscale coupled hydro-mechanical modelling of an underground excavation was performed to determine hydraulic and time-dependent deviatoric stress conditions, by taking into account the rock salt creep behaviour. Under the obtained macro-scale constraints, micro-scale modelling of a pathway dilation along halite grain boundaries was performed using different model strategies: a) coupled hydromechanical modelling with a consideration of hydraulic pressure-induced dilatant deformation, b) nonlinear dynamic model taking account of fluid migration, stress-dependent grain boundary wetting and shear-induced dilatancy of salt, and c) phase-field modelling of flow pathway propagation. The permeability increase resulting from the pathway dilation is estimated to be as high as two orders of magnitude. Based on the permeability determined, a series of pressure buildups measured from a borehole with a high hydrocarbon release rate, a total of 430 build-ups within a monitoring time of 938 days, can be simulated with a macro-scale compressible flow model accounting for different zones around the opening.

58 GEOSCIENCES↗
DOE OSTI2022

Effects of time-dependent deformation of shale on the integrity of a geological nuclear waste repository

Safety assessment of geological nuclear waste repositories is essential for the permanent disposal of spent nuclear fuels and high-level radioactive waste. The long-term integrity of the host rock as well as the engineered barrier system (e.g., bentonite buffer) surrounding nuclear waste canisters is of particular importance as decay heat from nuclear waste canisters, which will last over thousands of years, significantly disturbs the thermo-hydromechanical (THM) state of the repository. In this study, THM coupled simulations were carried out to investigate the effect of time-dependent deformation (i.e., creep) of shale on the long-term integrity of a generic subsurface nuclear waste repository. The Norton-Bailey creep model, which is also known as the Lemaitre-Menzel-Schreiner model, was employed to simulate the power-law type creep that is observed in shales. The TOUGH-FLAC simulator was employed for the THM coupled modeling of the repository. The objective of this study is to assess the effect of creep in different shales (i.e., high creep shale vs. low creep shale) on long-term stress and permeability changes in the repository. Results show potential advantages of constructing repositories in the high creep shale, as deviatoric stress levels in the formation decreased to zero in 100 years since the emplacement of nuclear waste canisters and the permeability also decreased to the undamaged, intrinsic levels in 10,000 years. Also, mean effective stress levels in the bentonite buffer increased by 100% in the high creep shale case relative to the low creep shale case at 10,000 years due to creep-induced contraction of the nuclear waste disposal tunnel. However, in earlier periods (e.g., 1000 years), the stress levels in the bentonite buffer were twice smaller in the high creep shale case than in the low creep shale case, which shows a tradeoff between the intermediate- (~1000 years) and long-term (>10,000 years) compaction levels in the bentonite buffer depending on the creep characteristics of the host shale.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Modeling supercritical CO2 injection induced rupture of a minor fault embedded in a poroelastic layered reservoir-caprock system

CO2 injection for geologic carbon sequestration involves hydromechanical processes that lead to changes in fluid pressure and stresses that can activate existing faults. This paper presents a new method and workflow of modeling fault activation considering more complex three-dimensional geometry of natural faults using the TOUGH-FLAC multiphase fluid flow and geomechanical simulator. In this method and workflow, FLAC3D mechanical interfaces and TOUGH3 finite volume elements are discretized using computer aided design and gridding software along with a tailored mesh translation routine. The method and workflow are demonstrated with a model of a curved minor fault embedded in a poro-elastic layered reservoir-caprock system. The model is used for a comprehensive sensitivity analysis of fault responses to fault length, injection mass rate, injection schedule, well-fault distance, and well locations versus fault location. Four metrics (CO2 plume, shear state of fault, pressure and stress path at fault monitoring points) are selected to assess CO2 migration, pressure change, and the reactivation of faults. The results reveal that CO2 can bypass around the tip of the minor impermeable fault, building up pressure and poro-elastic stress on both sides that tends to impede fault rupture. Our study shows the benefit of carefully designing the injection to achieve the targeted final storage volume, starting at a relatively low rate for considerable time, and then ramping up the injection rate to the full rate of injection. The initial low injection has two distinct benefits: (1) it allows for the formation of an extensive CO2 plume with a much higher mobility through a low viscosity that will result in a lower pressure for a given injection rate, and (2) it allows for gradual build-up of horizontal poro-elastic stress within the reservoir that will tend to impede activation of steeply dipping faults. The injection scenario starting at a low injection rate, denoted here as conservative injection, can significantly reduce the risk of fault activation as high fluid mobility and reservoir strengthening poro-elastic stress has been established long before reaching the peak injection rates. Moreover, simultaneous injection in two injection wells on both sides of fault can provide further reservoir strengthening through poro-elastic stress buildup acting on a fault under normal faulting stress regime. The findings presented in the paper can provide practical and effective guidance on long-term, safe, and reliable geological CO2 storage.

Cao, Meng↗
DOE OSTI2020

Assessing mechanical response of CO 2 storage into a depleted carbonate reef using a site-scale geomechanical model calibrated with field tests and InSAR monitoring data

Geomechanical risks of injection have raised concerns regarding secure CO 2 storage. In this work, a combined monitoring and modeling approach is used to assess the stress changes and surface uplift associated with CO 2 injection into a depleted carbonate reef of the Michigan basin. A site-scale geomechanical model is built by assigning mechanical properties of formations using well-log and experimental data. Gravity load is applied to the model to estimate the vertical component of stress as well as different lateral boundary displacement scenarios to estimate horizontal stresses. We used a poroelastic pressure-dependent model (instead of a linear elastic mechanical earth model) to calibrate initial stresses using hydraulic fracture test data measured at depleted reservoir status. Multi-phase fluid flow-geomechanical simulations are performed to estimate the poroelastic response during (1) primary depletion (2) field-scale CO 2 injection phase (3) a hypothetical forecast scenario in which well bottom hole pressure (BHP) reach 45000 KPa. The predicted surface uplift is less than 1 mm at the end of the field-scale CO 2 injection phase which is in good agreement with Interferometric Synthetic Aperture Radar (InSAR) uplift measurement. Although the InSAR data shows an insignificant uplift, hydromechanical modeling of injection shows that CO 2 injection still causes reservoir deformation emphasizing the role of carbonate overburden and reservoir formation mechanical properties and limited size of reef on diminishing the surface deformation. Modeling indicates poroelastic response of caprock matters to estimate uplift. The lower permeability of the top two layers provides additional barrier to large uplift. Also, history of subsidence due to production should be accounted to predict uplift due to a follow up injection correctly. This report shows the significance of combining a calibrated geomechanical model with field measured stresses and monitoring data to be used as a tool to ensure the safety of CO 2 storage.

42 ENGINEERING↗
DOE OSTI2024

Modeling injection-induced fault slip using long short-term memory networks

Stress changes due to changes in fluid pressure and temperature in a faulted formation may lead to the opening/shearing of the fault. This can be due to subsurface (geo)engineering activities such as fluid injections and geologic disposal of nuclear waste. Such activities are expected to rise in the future making it necessary to assess their short- and long-term safety. Here, a new machine learning (ML) approach to model pore pressure and fault displacements in response to high-pressure fluid injection cycles is developed. The focus is on fault behavior near the injection borehole. To capture the temporal dependencies in the data, long short-term memory (LSTM) networks are utilized. To prevent error accumulation within the forecast window, four critical measures to train a robust LSTM model for predicting fault response are highlighted: (i) setting an appropriate value of LSTM lag, (ii) calibrating the LSTM cell dimension, (iii) learning rate reduction during weight optimization, and (iv) not adopting an independent injection cycle as a validation set. Several numerical experiments were conducted, which demonstrated that the ML model can capture peaks in pressure and associated fault displacement that accompany an increase in fluid injection. The model also captured the decay in pressure and displacement during the injection shut-in period. Further, the ability of an ML model to highlight key changes in fault hydromechanical activation processes was investigated, which shows that ML can be used to monitor risk of fault activation and leakage during high pressure fluid injections.

58 GEOSCIENCES↗
DOE OSTI2023

Effects of anisotropic shale creep on the stress and permeability evolution of a geological nuclear waste repository

To ensure long-term safety and performance, geological nuclear waste repositories require low-permeability barriers such as bentonite buffers and/or shale host rock. Shale is not only known for its low permeability but also for its trend to undergo time-dependent deformation (i.e., creep), which could heal damage, but the effects of shale creep on the long-term performance of nuclear waste repositories have not been clearly understood. In particular, the anisotropic nature of shale (i.e., bedding) could have a significant effect on its creep behavior, and consequently, on the long-term performance of nuclear waste repositories. In this research, numerical simulations were carried out with the objective of showing the effects of anisotropic shale creep on the stress and permeability evolution of a generic geological nuclear waste repository in shale. The TOUGH-FLAC simulator, a thermo-hydromechanically (THM) coupled numerical code, was used for the simulations. To achieve the objective, comparisons were performed between the results of anisotropic shale creep simulations and those of different simulation cases, namely, no creep (i.e., elastic), isotropic creep, and long-term creep shale cases. Results of the comparisons show that the elastic and isotropic creep shale cases respectively led to the overestimation and underestimation of stress and permeability in the repository, whereas the long-term creep shale case, which accumulated greater creep in later periods than in earlier periods, helped to keep large shear and tensile stresses from developing while maintaining compressive spherical stress, resulting in consistently low permeability levels. These results indicate that performance assessments with elastic and isotropic creep formation models will provide the upper and lower bound estimates of stress and permeability, while more reasonable estimates will be given by an anisotropic creep formation model, and that shale with long-term creep characteristics will be beneficial in many aspects of the safety and performance of nuclear waste repositories.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Quantification of the Impact of Acidified Brine on Fracture-Matrix Transport in a Naturally Fractured Shale Using in Situ Imaging and Modeling

Understanding flow, transport, chemical reactions, and hydromechanical processes in fractured geologic materials is key for optimizing a range of subsurface processes including carbon dioxide and hydrogen storage, unconventional energy resource extraction, and geothermal energy recovery. Flow and transport processes in naturally fractured shale rocks have been challenging to characterize due to experimental complexity and the multiscale nature of quantifying continuum scale descriptions of mass exchange between micrometer-scale fractures and nanometer-scale pores. In this study, we use positron emission tomography (PET) to image the transport of a conservative tracer in a naturally fractured Wolfcamp shale core before and after the core was exposed to low pH brine conditions. Image-based experimental observations are interpreted by fitting an analytical transport model to fracture-containing voxels in the core. Results of this analysis indicate subtle increases in matrix diffusivity and a slightly more uniform fracture velocity distribution following exposure to low pH conditions. These observations are compared with a multicomponent one-dimensional reactive transport model that indicates the capacity for a 10% increase in porosity at the fracture-matrix interface as a result of the low pH brine exposure. This porosity change is the result of the dissolution of carbonate minerals in the shale matrix to low pH conditions. Further, this image-based workflow represents a new approach for quantifying spatially resolved fracture-matrix transport processes and provides a foundation for future work to better understand the role of coupled transport, reaction, and mechanical processes in naturally fractured rocks.

58 GEOSCIENCES↗
DOE OSTI2023

Characterization of Aquifer Poroelastic Response to Impulse and Oscillatory Well Pressure Using Distributed Acoustic Sensing

Abstract The storage of fluids in the subsurface is critical for a broad spectrum of applications including managed aquifer recharge, storage of liquefied carbon dioxide and hydrogen, geothermal heat extraction and exploitation of hydrocarbon. It is surprising then, that there has been relatively little measurement of the vertical distribution of poroelastic storage in geologic formations as compared with permeability. We present experiments in which fluid was injected into an important regional aquifer and the depth‐dependent strain response measured using fiber optic distributed acoustic sensing. The formation expansion and contraction in response to fluid injection were several 100 nanostrain. Strain, and the implied storage distribution, was highly localized in specific strata and demonstrated complex, hydromechanical behavior. This new window into fluid‐geomechanical coupling undermines some typically use models and observations currently in practice, but provides potential for complete representation and prediction of fluid storage in the subsurface.

58 GEOSCIENCES↗
DOE OSTI2021

A framework for data-driven solution and parameter estimation of PDEs using conditional generative adversarial networks

We employ and adapt the image-to-image translation concept based on conditional generative adversarial networks (cGAN) for learning a forward and an inverse solution operator of partial differential equations (PDEs). We focus on steady-state solutions of coupled hydromechanical processes in heterogeneous porous media and present the parameterization of the spatially heterogeneous coefficients, which is exceedingly difficult using standard reduced-order modeling techniques. We show that our framework provides a speed-up of at least 2,000 times compared to a finite-element solver and achieves a relative root-mean-square error (r.m.s.e.) of less than 2% for forward modeling. For inverse modeling, the framework estimates the heterogeneous coefficients, given an input of pressure and/or displacement fields, with a relative r.m.s.e. of less than 7%, even for cases where the input data are incomplete and contaminated by noise. The framework also provides a speed-up of 120,000 times compared to a Gaussian prior-based inverse modeling approach while also delivering more accurate results.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Estimating perturbed stress from 3-D borehole displacements induced by fluid injection in fractured or faulted shales

SUMMARY Hydrofracturing stress measurements in fractured and anisotropic shales are notoriously difficult, because opening of existing geological features tends to prevent the creation of a pure hydraulic fracture perpendicular to the least compressive principal stress. Here we show how adding 3-D borehole-displacement measurements while conducting the hydraulic injection test helps to better constrain the principal stress orientations and magnitudes. We developed a 3-D fully coupled hydromechanical numerical model to analyse the displacement, fluid pressure and injection flow-rate data measured during an injection pressure-step-rate test conducted to activate a faulted borehole interval in the Mont Terri Opalinus Clay (Switzerland). We find that injected fluids can only penetrate the fault when it is at or above the Coulomb failure pressure. Borehole displacement orientations are sensitive to a ∼15° variation in the stress–tensor orientation and a 1 MPa stress magnitude variation. Although some dispersion occurs while rupture is propagating along the fault plane ∼4 m away from the borehole, the maximum density of displacement orientations consistently informs about the stress orientation. Thus, an extended injection step-rate approach coupled with an accurate in situ measurement of the borehole wall displacements can be used to better constrain the local stress field perturbations in fractured shales and in heterogeneous rock in general.

Guglielmi, Yves↗
DOE OSTI2020

Fluid-driven fractures in granular media: Insights from numerical investigations

We investigate the mechanisms of opening-mode fracture initiation in granular media. The study is based on a simulation of grain-scale fluid-grain interactions through a coupled numerical approach in which the discrete element method is used to solve for the mechanics of a solid granular medium, and computational fluid dynamics is used to model fluid flow and drag forces. In this work, we present benchmark problems with analytical solutions and validate this numerical model against experiments on a viscous-drag-driven cavity in the literature. Additional simulation results show fracture initiation mechanisms in a random granular packing subjected to constant boundary stresses and to fluid injection with a localized source. The dimensionless variable $F_s/F_{sk}$ (ratio of seepage force $F_s$ and skeletal force $F_{sk}$) incorporates the impacts of physical properties and injection parameters including fluid viscosity, injection velocity, grain size, and effective stresses, and it has been used as a criterion separating regimes of fluid invasion and drag-driven fracture opening. Our simulation results show that $F_s/F_{sk}$ in combination with $τ_1$ (ratio of diffusion time from hydromechanical coupling and injection time) serves as a prediction of fracture opening within granular packing. We suggest a simple criterion ($F_s/F_{sk}$ > 1 or $τ_1$ > 0.17) that is valid for various types of granular media and injection conditions to determine if fracture opening will occur. Among other applications, this study is useful to predict the initiation and propagation of fractures in natural sediments.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗