Search NASA⌕ Search

SEARCH · Search NASA

Results for “hydronium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of electrode rinse solutions on the electrodialysis of concentrated salts

The data presented indicate that modest attention to the chemistry of the electrode rinse solution can yield as much as 56% improvement in process efficiency. When operating electrodialysis (ED) with salt concentrations greater than 10,000 mg/l (as NaCl) the amperage can be relatively high even at low voltages. To maximize the overall rate of ion transport from diluate to concentrate, there is a need to minimize resistances in the electrode cells since these can represent as much as 30% of the total resistances in the entire process and in this particular ED unit, represented resistance roughly equivalent to that within the membrane stack. This work describes the performance of a 10-cell pair, 200 cm 2 (0.02 m 2 ) per membrane, pilot ED unit operated in batch mode at 5 V potential. The feedstock to the stack was varied from 0.5% to 6% NaCl. Results from Volt-amp profiles (2.0–15 V) were used as the rationale for choosing the preferred electrode rinse solution, 90 g/l (kg/m 3 ) disodium sulfate at pH 12.5. The recommended solution of 30 g/l (kg/m 3 ) disodium sulfate at neutral pH was tested against stronger solutions (60, 90, and 120 g/l (kg/m 3 ) disodium sulfate) at neutral pH and with 1 g/l (kg/m 3 ) sodium hydroxide added to yield solutions at pH 12.5. There were stark differences in the performance of the ED unit between the solutions at pH 7 and those at pH 12.5. The slopes of the Volt-amp profiles improved indicating less resistance to ion flow at pH 12.5. Most of the difference can be attributed to the greater conductivity of sodium hydroxide compared to disodium sulfate, where even a modest addition of 1 g/l (kg/m 3 ) sodium hydroxide increased the conductivity of the solution between 8 and 20% depending on the concentration of disodium sulfate. Most notably, the initiation voltage was 2.39 ± 0.08 V with solutions at pH 7 and 1.99 V ± 0.04 V when the rinse solutions were around pH 12.5, a difference of around 0.42 V. Since the full batch runs were performed at 5.0 V, this 0.42 V differential represented a loss of 8% in process efficiency. A series of tests showed a shift in initiation voltage occurred between pH 11.5 and 12.5. Nernst equations for water electrolysis are coupled with a simple flux model that estimates the concentration of hydroxide and hydronium ions at the electrode surfaces. This model indicates that the potential demanded by the electrodes is directly linked to the current. Furthermore, there is a steep drop in the potential demanded by the anode when there is sufficient hydroxide available to generate oxygen from hydroxide as opposed to generation from water. The voltage demand is minimal at pH 12.5 and reflective of the reference standard voltage (just over 1.23 V predicted at 0.1 amps). However, the flux model predicts that the voltage demanded by the electrodes at pH 7 is 1.61 V at 0.1 amps (the lowest amperage measurable with the power pack). In conclusion, comparing this result to the reference standard (E 0 = -1.23 V) yields a satisfactory explanation for the observed difference below reference standard of 0.42 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

How Water Attacks MXene

Two-dimensional (2D) transition metal carbides and nitrides (MXenes) have shown outstanding performances in electrochemical energy storage and many other applications. However, the stability of MXene remains a concern, especially its quick degradation in aqueous solutions under ambient conditions. Here, we report on the water/Ti 3 C 2 O 2 -MXene interfacial chemistry from first-principles molecular dynamics simulations at room temperature. Surprisingly, we find that the water molecules can attack the basal plane of Ti 3 C 2 O 2 and pull the surface Ti atoms out, thereby reconstructing the surface. Further, by tracking close encounters of water molecules and surface Ti atoms on the basal plane of Ti 3 C 2 O 2 , we show that the attack is initiated by the chemisorption of a water molecule on a surface Ti atom, followed by the breaking of Ti–C bonds and deprotonation of the water molecule, leading to the formation of Ti–OH on the Ti 3 C 2 O 2 surface and a hydronium ion in the aqueous phase. Our finding highlights the susceptibility of Ti 3 C 2 O 2 MXene to water attack, supporting recent experimental observations. Furthermore, we demonstrate that preventing close encounters of water molecules and the surface Ti atoms is key to the stability of the basal plane and can be realized by negatively charging the surface (thereby reorienting the O atoms of water away from the surface) or converting the surface O to -OH groups (thereby shifting the water layer further away from the surface). Our insights and approach highlight the importance of the reactivity of water when interfacing with 2D materials such as MXenes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Low-Energy Isomers of the Magic Number H + (H 2 O) 21 Cluster

Electronic structure calculations are used to characterize low-energy isomers of H + (H 2 O) 21 . Eleven different classes of isomers, based on the (H 2 O) 20 pentagonal dodecahedron with the excess proton localized on the surface (as a hydrated hydronium ion) and the “extra” water molecule located in the interior of the cluster, are characterized. In 10 of these classes, the internal water molecule is engaged in six 5-membered rings, but in the remaining class, which is predicted to start at only 0.6 kcal/mol above the global minimum, the internal water is engaged in a 4- membered ring, an additional 6-membered ring, and four 5- membered rings. In addition, isomers with two 4-membered rings and two 6-membered rings on the cluster surface are predicted to start at only ∼1.3 kcal/mol above the lowest-energy dodecahedralbased structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Resolving Heterogeneous Dynamics of Excess Protons in Aqueous Solution with Rate Theory

Rate theories have found great utility across the chemical sciences by providing a physically transparent way to analyze dynamical processes. Here we demonstrate the benefits of using transition state theory and Marcus theory to study the rate of proton transfer in HCl solutions. By using long ab initio molecular dynamics simulations we show that good agreement is obtained between these two different formulations of rate theory and how they can be used to study the pathways and life-time of proton transfer in aqueous solution. Since both rate theory formulations utilize identical sets of molecular data, this provides a self-consistent theoretical picture of the rates of aqueous phase proton transfer. Specifically, we isolate and quantify the rates of proton transfer, ion-pair dissociation, and solvent exchange in concentrated HCl solutions. Our analysis predicts a concentration dependence to both proton transfer and ion-pairing. Moreover, our estimate of the life-time for the Zundel species is 0.8 ps and 1.3 ps for 2M and 8M HCl, respectively. In this paper, we demonstrate that concentration effects, can indeed be quantified through the combination of state-of-the-art simulation and theory and provides a picture of the important correlations between the cation (hydronium) and the counter-ion in acid solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Molecular Origins of the Barriers to Proton Transport in Acidic Aqueous Solutions

The self-consistent iterative multistate empirical valence bond (SCI-MS-EVB) method is used to analyze the structure, thermodynamics, and dynamics of hydrochloric acid solutions. The reorientation timescales of irreversible proton transport are elucidated by simulating 0.43 M, 0.85 M, 1.68 M, and 3.26 M HCl solutions at 270 K, 285 K, 300 K, 315 K, and 330 K. The results indicate increased counter-ion pairing with increasing concentration, which manifests itself via a reduced hydronium oxygen–chloride (O*-Cl) structuring in the radial distribution functions. Increasing ionic concentration also reduces the diffusion of the hydrated excess protons, principally by reducing the contribution of the Grotthuss proton hopping (shuttling) mechanism to the overall diffusion process. In agreement with prior experimental findings, a decrease in the activation energy of reorientation timescales was also observed, which is explicitly explained using activated rate theory and an energy-entropy decomposition of the state-averaged radial distribution functions. Furthermore, these results provide atomistic verification of suggestions from recent two-dimensional infrared spectroscopy experiments that chloride anions (as opposed to hydrated excess protons) create entropic barriers to proton transport.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Water-Assisted Proton Transport in Confined Nanochannels

Hydrated excess protons under hydrophobic confinement are a critical component of charge transport behavior and reactivity in nanoporous materials and biomolecular systems. In this study, excess proton confinement effects are computationally investigated for sub-2 nm hydrophobic nanopores by varying the diameters (d = 0.81, 0.95, 1.09, 1.22, 1.36, 1.63, and 1.90 nm), lengths (l ~3 and ~5 nm), curvature, and chirality of cylindrical carbon nanotube (CNT) nanopores. CNTs with a combination of different diameter segments are also explored. The spatial distribution of water molecules under confinement is diameter-dependent; however, proton solvation and transport are consistently found to occur in the water layer adjacent to the pore wall, showing an “amphiphilic” character of the hydrated excess proton hydronium-like structure. The proton transport free energy barrier also decreases significantly as the nanopore diameter increases and proton transport becomes almost barrierless in the d > 1 nm nanopores. Among the nanopores studied, the Zundel cation (H 5 O 2 + ) is populated only in the d = 0.95 nm CNT (7,7) nanopore. The presence of the hydrated excess proton and K + inside the CNT (7,7) nanopore induces a water density increase by 40 and 20%, respectively. The K + transport through CNT nanopores is also consistently higher in the free energy barrier than proton transport. Interestingly, the evolution of excess protonic charge defect distribution reveals a “frozen” single water wire configuration in the d = 0.81 nm CNT (6,6) nanopore (or segment), through which hydrated excess protons can only shuttle via the Grotthuss mechanism. Vehicular diffusion becomes relevant to proton transport in the “flat” free energy regions and in the wider nanopores, where protons do not primarily shuttle in the axial direction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

First-Principles Grand-Canonical Simulations of Water Adsorption in Proton-Exchanged Zeolites

Water appears by design or as impurities in many important reactive systems. For those catalyzed by porous solid acids, such as widely used zeolites, experimentally quantifying the amount or elucidating the structure of adsorbed water clusters at reaction conditions is challenging, while computational studies (e.g., first-principles molecular dynamics simulations) often need to assume the loading to examine solvation effects. Furthermore, we perform first-principles grand-canonical simulations to predict water adsorption to H-ZSM-5 zeolites under specified experimental conditions. Presampling with inexpensive force fields and a pool-based parallelization algorithm are used to improve simulation efficiency, while molecular dynamics is used to sample configurations involving hydronium species. We observe that H + exchange dramatically increases the hydrophilicity of zeolite MFI and an appreciable amount of water is present at very low relative humidities. At all conditions examined, the zeolitic protons are found to dissociate readily from the surface basic sites and become mobile by participating in the hydrogen-bonded chains of adsorbed water molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Size-Dependent Onset of Nitric Acid Dissociation in Cs + ·(HNO 3 )(H 2 O) n =0–11 Clusters at 20 K

We report the water-mediated charge separation of nitric acid upon incorporation into size-selected Cs + ∙(HNO 3 )(H 2 O) n=0-11 clusters at 20 K. Dramatic spectral changes are observed in the range n=7-9 that are traced to the formation of many isomeric structures associated with intermediate transfer of the acidic proton to the water network. This transfer is complete by n=10, which exhibits much simpler vibrational band patterns consistent with those expected for a tri-coordinated hydronium ion (the Eigen motif) along with the NO stretching bands predicted for a hydrated NO 3 – anion that is directly complexed to the Cs + cation. Theoretical analysis of the n=10 spectrum indicates that the dissociated ions adopt a solvent-separated ion-pair configuration such that the Cs + and H 3 O + cations flank the NO 3 – anion in a microhydrated salt bridge. In conclusion, this charge separation motif is evidently assisted by the electrostatic stabilization of the product NO 3 – /H 3 O + ion pair by the proximal metal ion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Rate Enhancement of Acid-Catalyzed Alcohol Dehydration by Supramolecular Organic Capsules

The presence of a (sub)nanometric environment has been demonstrated to enhance the rate of homogeneous acid-catalyzed reactions. Conventionally, such catalysts are constructed by directly embedding a catalytically active acid site into the structure of a porous material, linking the acid properties with the properties of the embedding solid. Here, a holoenzyme mimicking approach was used, in which a self-assembled hexameric resorcinarene capsule (1.4 nm 3 cavity) acts like an apoenzyme that transforms into a catalytically active site by hosting hydrated HCl as a cofactor. This capsule binds the hydronium ion together with cyclohexanol (CyOH) and catalyzes the dehydration to cyclohexene with enhanced rates that are 2 orders of magnitude higher than those in the unconstrained environment. Kinetic analysis shows that cyclohexanol dehydration proceeds via an E2 mechanism on hydrated HCl in the unconstrained environment, while the constrained environment of the active capsule induces the stabilization of an ionic intermediate, allowing an E1 mechanism to dominate. By comparison with the reaction in zeolite environments, we show that the direct chemical environment of the capsule or a zeolite wall exerts only a minor direct influence. The volume constraint increases the reaction rate by inducing a larger activation entropy, indicating the stabilization of a later transition state in the E1 mechanism, as well as a higher reaction space of the carbenium ion constituting the transition state.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Differences in Mechanism and Rate of Zeolite-Catalyzed Cyclohexanol Dehydration in Apolar and Aqueous Phase

The rate of acid-base catalyzed dehydration of alcohols strongly depends on the solvent and the environment of the acid sites. In this work, we find that Brønsted acidic sites in large-pore zeolites, but not in medium-pore zeolites, catalyze cyclohexanol dehydration in decalin at significantly higher rates than hydrated hydronium ions in aqueous phase. Specifically, the difference in turnover rates between the two solvents amounts to two to three orders of magnitude on H-BEA and H-FAU, while being very modest (within a factor of 2) for H-MFI. Combining kinetic, isotopic tracer and 2H NMR measurements, it is established that cyclohexanol dehydration generally follows an E1-elimination pathway in decalin. A notable exception is the monomer dehydration route on H-MFI, which exhibits a much lower activation energy and a substantially negative activation entropy that appear to be associated with an E2-type mechanism. The C-O bond cleavage displays a dominant degree of rate control in decalin, which stands in contrast to deprotonation (C-H cleavage) being rate-limiting in aqueous-phase dehydration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Observation of Slow Eigen-Zundel Interconversion in H + (H 2 O) 6 Clusters upon Isomer-Selective Vibrational Excitation and Buffer Gas Cooling in a Cryogenic Ion Trap

The formation of isomers when trapping floppy cluster ions in a temperature-controlled ion trap is a generally observed phenomenon. This involves collisional quenching of the ions initially formed at high temperature by buffer gas cooling until their internal energies fall below the barriers in the potential energy surface that separate them. Here we explore the kinetics at play in the case of the two isomers adopted by the H + (H 2 O) 6 cluster ion that differ in the proton accommodation motif. One of these is most like the Eigen cation with a tricoordinated hydronium motif (denoted E), and the other is most like the Zundel ion with the proton equally shared between two water molecules (denoted Z). After initial cooling to about 20 K in the radiofrequency (Paul) trap, the relative populations of these two spectroscopically distinct isomers are abruptly changed through isomer-selective photoexcitation of bands in the OH stretching region with a pulsed (~6 ns) infrared laser while the ions are in the trap. We then monitor the relaxation of the vibrationally excited clusters and reformation of the two cold isomers by recording infrared photodissociation spectra with a second IR laser as a function of delay time from the initial excitation. The latter spectra are obtained after ejecting the trapped ions into a time-of-flight photofragmentation mass spectrometer, thus enabling long (~0.1 s) delay times. Excitation of the Z isomer is observed to display long-lived vibrationally excited states that are collisionally cooled on a ms time scale, some of which quench into the E isomer. These excited E species then display spontaneous interconversion to the Z form on a ~10 ms time scale. Furthermore, these qualitative observations set the stage for a series of experimental measurements that can provide quantitative benchmarks for theoretical simulations of cluster dynamics and the potential energy surfaces that underlie them.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Thermodynamic driving forces in contact electrification between polymeric materials

Abstract Contact electrification, or contact charging, refers to the process of static charge accumulation after rubbing, or even simple touching, of two materials. Despite its relevance in static electricity, various natural phenomena, and numerous technologies, contact charging remains poorly understood. For insulating materials, even the species of charge carrier may be unknown, and the direction of charge-transfer lacks firm molecular-level explanation. Here, we use all-atom molecular dynamics simulations to investigate whether thermodynamics can explain contact charging between insulating polymers. Based on prior work suggesting that water-ions, such as hydronium and hydroxide ions, are potential charge carriers, we predict preferred directions of charge-transfer between polymer surfaces according to the free energy of water-ions within water droplets on such surfaces. Broad agreement between our predictions and experimental triboelectric series indicate that thermodynamically driven ion-transfer likely influences contact charging of polymers. Furthermore, simulation analyses reveal how specific interactions of water and water-ions proximate to the polymer-water interface explain observed trends. This study establishes relevance of thermodynamic driving forces in contact charging of insulators with new evidence informed by molecular-level interactions. These insights have direct implications for future mechanistic studies and applications of contact charging involving polymeric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Water structure and electric fields at the interface of oil droplets

Interfacial water exhibits rich and complex behaviour, playing an important part in chemistry, biology, geology and engineering. However, there is still much debate on the fundamental properties of water at hydrophobic interfaces, such as orientational ordering, the concentration of hydronium and hydroxide, improper hydrogen bonds and the presence of large electric fields. This controversy arises from the challenges in measuring interfacial systems, even with the most advanced experimental techniques and theoretical approaches available. Here we report on an in-solution, interface-selective Raman spectroscopy method using multivariate curve resolution to probe hexadecane-in-water emulsions, aided by a monomer-field theoretical model for Raman spectroscopy. Our results indicate that oil-water emulsion interfaces can exhibit reduced tetrahedral order and weaker hydrogen bonding, along with a substantial population of free hydroxyl groups that experience about 95 cm -1 redshift in their stretching mode compared with planar oil-water interfaces. Given the known electrostatic zeta potential characteristic of oil droplets, we propose the existence of a strong electric field (about 50-90 MV cm -1 ) emanating from the oil phase. This field is inferred indirectly but supported by control experiments and theoretical estimates. These observations are either absent or opposite in the molecular hydrophobic interface formed by small solutes or at planar oil-water interfaces. Instead, water structural disorder and enhanced electric fields emerge as unique features of the mesoscale interface in oil-water emulsions, potentially contributing to the accelerated chemical reactivity observed at hydrophobic-water interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Implications of the fractional charge of hydroxide at the electrochemical interface

Rational design of materials that efficiently convert electrical energy into chemical bonds will ultimately depend on a thorough understanding of the electrochemical interface at the atomic level. Towards this goal, the use of density functional theory (DFT) at the generalized gradient approximation (GGA) level has been applied widely in the past 15 years. In the calculation of electrochemical reaction energetics using GGA-DFT, it is frequently implicitly assumed that ions in the Helmholtz plane have unit charge. However, the ion charge is observed to be fractional near the interface through both a capacitor model and through Bader charge partitioning. In this work, we show that this spurious charge transfer can be effectively mitigated by continuum charging of the electrolyte. Finally, we show that, similar to hydronium, the observed fractional charge of hydroxide is not due to a GGA level self-interaction error, as the partial charge is observed even when using hybrid level exchange–correlation functionals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Interfacial solvation and slow transport of hydrated excess protons in non-ionic reverse micelles

This work employs molecular dynamics simulations to investigate the solvation and transport properties of hydrated excess protons (with a hydronium-like core structure) in non-ionic Igepal CO-520 reverse micelles of various sizes in a non-polar solvent. Multiscale Reactive Molecular Dynamics (MS-RMD) simulations were used to describe vehicular and hopping diffusion during the proton transport process. As detailed herein, an excess proton shows a marked tendency to localize in the interfacial region of micellar water pools. Slow proton transport was observed which becomes faster with increasing micellar size. Further analysis reveals that the slow diffusion of an excess proton is a combined result of slow water diffusion and the low proton hopping rate. This study also confirms that a low proton hopping rate in reverse micelles stems from the interfacial solvation of hydrated excess protons and the immobilization of interfacial water. The low water density in the interfacial region makes it difficult to form a complete hydrogen bond network near the hydrated excess proton, and therefore locks in the orientation of hydrated proton cations. The immobilization of the interfacial water also slows the relaxation of the overall hydrogen bond network.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Intercalation–exfoliation processes during ionic exchange reactions from sodium lepidocrocite-type titanate toward a proton-based trititanate structure

Topochemical reactions involving ionic exchange have been used to assess a large number of metastable compositions, particularly in layered metal oxides. This method encompasses complex reactions that are poorly explored, yet are of prime importance to understand and control the materials’ properties. In this work, we embark on investigating the reactions involved during the ionic exchange between a layered Na-titanate (lepidocrocite-type structure) and an acidic solution (HCl), leading to a protonic (H 3 O + ) titanate (trititanate structure). The reactions involve an ionic exchange provoking a structural change from the lepidocrocite-type to the trititanate structure as shown by real-space refinements of ex situ pair distribution function data. Mobile Na + ions are exchanged by hydronium ions inducing high proton mobility in the final structure. Moreover, the reaction was followed by ex situ 23 Na and 1 H solid-state MAS NMR which allowed, among other things, confirming that the Na + ions are in the interlayer space and specifying their local environment. Strikingly, the ionic exchange reaction induces progressive exfoliation of the Na-titanate particles leading to 2–5 nm thin elongated crystallites. To further understand the different steps associated with the ionic exchange, the evolution of the electrolytic conductivity, using conductimetric titration, has been monitored upon HCl addition, enabling characterization of the intercalation(H + )/de-intercalation(Na + ) reactions and assessing kinetic parameters. Accordingly, it is hypothesized that the exfoliation of the particles is due to the accumulation of charges at the particle level in relation to the rapid intercalation of protons. This work provides novel insights into ionic exchange reactions involved in layered oxide compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Self-interaction correction in water–ion clusters

We study the importance of self-interaction errors in density functional approximations for various water–ion clusters. We have employed the Fermi-Löwdin orbital self-interaction correction (FLOSIC) method in conjunction with LSDA, PBE, and SCAN to describe binding energies of hydrogen-bonded water–ion clusters, i.e., water–hydronium, water– hydroxide, water–halide, as well as non-hydrogen-bonded water–alkali clusters. In the hydrogen-bonded water–ion clusters, the building blocks are linked by hydrogen atoms, although the links are much stronger and longer-ranged than the normal hydrogen bonds between water molecules, because the monopole on the ion interacts with both permanent and induced dipoles on the water molecules. We find that self-interaction errors overbind the hydrogen-bonded water– ion clusters and that FLOSIC reduces the error and brings the binding energies into closer agreement with higher–level calculations. Here, the non-hydrogen-bonded water–alkali clusters are not significantly affected by self-interaction errors. Self-interaction corrected PBE predicts the lowest mean unsigned error in binding energies (≤ 50 meV/H 2 O) for hydrogen-bonded water–ion clusters. Self-interaction errors are also largely dependent on the cluster size, and FLOSIC does not accurately capture the subtle variation in all clusters, indicating the need for further refinement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗