Search NASA⌕ Search

SEARCH · Search NASA

Results for “impulse test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Testing of molded high temperature plastic actuator road seals for use in advanced aircraft hydraulic systems

Molded high temperature plastic first and second stage rod seal elements were evaluated in seal assemblies to determine performance characteristics. These characteristics were compared with the performance of machined seal elements. The 6.35 cm second stage Chevron seal assembly was tested using molded Chevrons fabricated from five molding materials. Impulse screening tests conducted over a range of 311 K to 478 K revealed thermal setting deficiencies in the aromatic polyimide molding materials. Seal elements fabricated from aromatic copolyester materials structurally failed during impulse cycle calibration. Endurance testing of 3.85 million cycles at 450 K using MIL-H-83283 fluid showed poorer seal performance with the unfilled aromatic polyimide material than had been attained with seals machined from Vespel SP-21 material. The 6.35 cm first stage step-cut compression loaded seal ring fabricated from copolyester injection molding material failed structurally during impulse cycle calibration. Molding of complex shape rod seals was shown to be a potentially controllable technique, but additional molding material property testing is recommended.

Waterman, A. W.↗

A higher harmonic control test in the DNW to reduce impulsive BVI noise

A model rotor acoustic test was performed to examine the benefit of higher control (HHC) of blade pitch to reduce blade-vortex interaction (BVI) impulse noise. A 40-percent dynamically scaled, four-bladed model of a BO-105 main rotor was tested in the German-Dutch Wind Tunnel (DNW). Acoustic measurements were made in a large plane underneath the rotor employing a traversing in-flow microphone array in the anechoic environment of the open test section. Noise characteristics and noise directivity patterns as well as vibratory loads were measured and used to demonstrate the changes when different HHC schedules (different modes, amplitudes, phases) were applied. Dramatic changes of the acoustic signatures and the noise radiation directivity with HHC phase variations are found. Compared to the baseline conditions (without HHD), significant mid-frequency noise reductions of as much as 6 dB are obtained for low speed descent conditions where BVI is most intensive. For other rotor operating conditions with less intense BVI there is less or no benefit from the use of HHC. Low frequency loading noise and vibratory loads, especially at optimum noise reduction control settings, are found to increase.

Splettstoesser, Wolf R.↗

A Micro Newton Impulse-Bit Hydrazine Thruster - Design, Test, and Mission Applications

A small thruster, that will herein be called the Hydrazine milliNewton Thruster (HmNT), has been designed and vacuum hot-fire tested, demonstrating a range of thrust and impulse far below the current state-of-the-art (SOA) hydrazine thruster. Steady-state thrust levels of 35–135 mN, and minimum impulse-bits of 25–120 μN-s were demonstrated over a typical operating range of inlet pressures. These capabilities provide new spacecraft and mission design options, including the following: Functional backup for Reaction Wheel Assemblies (RWAs), which can be used to prolong the useful life of RWAs; RWA replacement for certain missions to save mass, power, and cost; Precision delta-V that can be used for: proximity operations and docking maneuvers, formation flying, primary attitude control for SmallSats and CubeSats, and primary delta-V for CubeSats.

Scharf, Daniel P.↗

Test stand for precise measurement of impulse and thrust vector of small attitude control jets

A test stand which accurately measures the impulse bit and thrust vector of reaction jet thrusters used in the attitude control system of space vehicles has been developed. It can be used to measure, in a vacuum or ambient environment, both impulse and thrust vector of reaction jet thrusters using hydrazine or inert gas propellants. The ballistic pendulum configuration was selected because of its accuracy, simplicity, and versatility. The pendulum is mounted on flexure pivots rotating about a vertical axis at the center of its mass. The test stand has the following measurement capabilities: impulse of 0.00004 to 4.4 N-sec (0.00001 to 1.0 lb-sec) with a pulse duration of 0.5 msec to 1 sec; static thrust of 0.22 to 22 N (0.05 to 5 lb) with a 5 percent resolution; and thrust angle alinement of 0.22 to 22 N (0.05 to 5 lb) thrusters with 0.01 deg accuracy.

Woodruff, J. R.↗

Modeling and Analysis of Structural Dynamics for a One-Tenth Scale Model NGST Sunshield

New modeling and analysis techniques have been developed for predicting the dynamic behavior of the Next Generation Space Telescope (NGST) sunshield. The sunshield consists of multiple layers of pretensioned, thin-film membranes supported by deployable booms. Modeling the structural dynamic behavior of the sunshield is a challenging aspect of the problem due to the effects of membrane wrinkling. A finite element model of the sunshield was developed using an approximate engineering approach, the cable network method, to account for membrane wrinkling effects. Ground testing of a one-tenth scale model of the NGST sunshield were carried out to provide data for validating the analytical model. A series of analyses were performed to predict the behavior of the sunshield under the ground test conditions. Modal analyses were performed to predict the frequencies and mode shapes of the test article and transient response analyses were completed to simulate impulse excitation tests. Comparison was made between analytical predictions and test measurements for the dynamic behavior of the sunshield. In general, the results show good agreement with the analytical model correctly predicting the approximate frequency and mode shapes for the significant structural modes.

Johnston, John↗

Pressure and force measurements on models set in hypersonic flows: A review

A review of measurement techniques used to obtain aerodynamic forces and moments and surface/flow field pressures for models tested in impulse hypersonic-hypervelocity facilities and in conventional-type hypersonic wind tunnels is presented. Although force and moment measurement techniques presently used in hypersonic wind tunnels are relatively unchanged from the 1960's and 1970's, significant advances have recently been made for impulse facilities. For both hypersonic wind tunnels and impulse facilities, the state-of-the-art has advanced via refinements, improved test techniques, and advances in semiconductor technology, data acquisition systems, and computers. The introduction of electronically scanned pressure systems over a decade ago 'revolutionized' pressure measurements in hypersonic wind tunnels and a second 'revolution' is impending with the development and application of optical, two-dimensional, global pressure measurement techniques. The development and continued refinement of miniature piezoresistive transducers has provided the capability to perform detailed surface pressure measurements on relatively small, complex models in impulse facilities; these transducers also provided the capability for intrusive flow field pressure measurements with miniature survey rakes.

Miller, Charles G.↗

Flight and wind tunnel tests of an electro-impulse de-icing system

A joint University-Industry project has been sponsored by NASA Lewis Research Center to develop the Electro-Impulse method for de-icing aircraft. The program has consisted of basic analyses, laboratory testing, icing tunnel tests, and flight tests. During the past two years, the EIDI system has been tested and refined, and has been shown to be a low-energy, highly reliable de-icing system for a wide range of conditions. This paper gives a brief review of conditions. This paper gives a brief review of the basic principles, the development history, and results of recent flight tests by NASA and by Cessna Aircraft Company.

Zumwalt, G. W.↗

Results of the NASP Ames Integrated Mixing Hypersonic Engine (AIMHYE) Scramjet Test Program

This paper describes the test techniques and results from the National Aerospace Plane Government Work Package 53, the Ames Integrated Mixing Hypersonic Engine (AIMHYE) Scramjet Test program conducted in the NASA Ames 16-Inch Combustion Driven Shock Tunnel. This was a series of near full-scale scramjet combustor tests with the objective to obtain high speed combustor and nozzle data from an engine with injector configurations similar to the NASP E21 and E22a designs. The experimental test approach was to use a large combustor model (80-100% throat height) designed and fabricated for testing in the semi-free jet mode. The conditions tested were similar to the "blue book" conditions at Mach 12, 14, and 16. GWP 53 validated use of large, long test time impulse facilities, specifically the Ames 16-Inch Shock Tunnel, for high Mach number scramjet propulsion testing an integrated test rig (inlet, combustor, and nozzle). Discussion of key features of the test program will include: effects of the 2-D combustor inlet pressure profile; performance of large injectors' fueling system that included nozzlettes, base injection, and film cooling; and heat transfer measurements to the combustor. Significant instrumentation development and application efforts include the following: combustor force balance application for measurement of combustor drag for comparison with integrated point measurements of skin friction; nozzle metric strip for measuring thrust with comparison to integrated pressure measurements; and nonintrusive optical fiber-based diode laser absorption measurements of combustion products for determination of combustor performance. Direct measurements will be reported for specific test article configurations and compared with CFD solutions.

Cavolowsky, John A.↗

A Micro Newton Impulse-Bit Hydrazine Thruster - Design, Test and Mission Applications

Recent and numerous failures of reaction wheels have cut short and/or limited the mission functions of several spacecraft including DAWN, Mars Odyssey, and Kepler among others. A micro Newton impulse-bit hydrazine thruster has the potential to backup or even replace reaction wheels on most missions, thereby extending mission life. This paper will discuss the development and test of a plug-and-play hydrazine thruster with 30 – 130 milliNewton thrust levels, and impulse bits < 50 microNewton-sec. In addition, this paper will address mission applications that include backup for, or even replacement of reaction wheels, delta-V thrust for CubeSats, and primary attitude control for the 20 – 50 kg class of spacecraft.

Parker, J. Morgan↗

Design, fabrication and test of the RL10 derivative II chamber/primary nozzle

The design, fabrication and test of the RL10-II chamber/primary nozzle was accomplished as part of the RL10 Product Improvement Program (PIP). The overall goal of the RL10 PIP was to gain the knowledge and experience necessary to develop new cryogenic upper stage engines to fulfill future NASA requirements. The goal would be reached by producing an RL10 engine designed to be reusable, operate at several thrust levels, and have increased performance. The goals for the chamber/primary nozzle task were: (1) to design a reusable assembly capable of operation at increased mixture ratio and low thrust; (2) to fabricate three assemblies using new or updated techniques where possible; and (3) to test one assembly to verify the design and construction. The design and fabrication phases produced an assembly having improved features such as single piece reinforcing band segments (i.e., Mae West segments) and relocated tube exit braze joints (i.e., hooked tube exit). In addition, a computer program was developed to design the chamber tubes to meet both performance and heat transfer requirements. The test phase showed the specific impulse of the test bed engine system to be as predicted. These results, along with the heat transfer data obtained, sufficiently proved the overall design of the RL10-II recontoured and shortened chamber/primary nozzle assembly.

Marable, R. W.↗

Pulsed plasma microthruster for synchronous meteorological satellite /SMS/

Two completely self contained variable thrust flight prototype plasma propulsion systems using solid teflon as propellant were designed, built and laboratory tested. The impulse bit amplitude of each thruster is 25 micro lb-sec. Impulse bits can be provided at rates varying from 50 ppm to 110 ppm. The total impulse capability is 400 lb-sec. Only 23 watts of bus power are required at maximum pulse rate. The system was subjected and passed the required vibration schedule and thermal vacuum test after a minor change in capacitor end face material. A 13 million discharge life test of the system was subsequently performed.

Guman, W. J.↗

Medium power hydrogen arcjet performance

An experimental investigation was performed to evaluate hydrogen arcjet operating characteristics in the range of 1 to 4 kW. A series of nozzles were operated in modular laboratory thrusters to examine the effects of geometric parameters such as constrictor diameter and nozzle divergence angle. Each nozzle was tested over a range of current and mass flow rates to explore stability and performance. In the range of mass flow rates and power levels tested, specific impulse values between 650 and 1250 sec were obtained at efficiencies between 30 and 40 percent. The performance of the two larger half angle (20, 15 deg) nozzles was similar for each of the two constrictor diameters tested. The nozzles with the smallest half angle (10 deg) were difiicult to operate. A restrike mode of operation was identified and described. Damage in the form of melting was observed in the constrictor region of all the nozzle inserts tested. Arcjet ignition was also difficult in many tests and a glow discharge mode that prevents starting was identified.

Curran, Francis M.↗

Medium power hydrogen arcjet performance

An experimental investigation was performed to evaluate hydrogen arcjet operating characteristics in the range of 1 to 4 kW. A series of nozzles were operated in modular laboratory thrusters to examine the effects of geometric parameters such as constrictor diameter and nozzle divergence angle. Each nozzle was tested over a range of current and mass flow rates to explore stability and performance. In the range of mass flow rates and power levels tested, specific impulse values between 650 and 1250 sec were obtained at efficiencies between 30 and 40 percent. The performance of the two larger half angle (20, 15 deg) nozzles was similar for each of the two constrictor diameters tested. The nozzles with the smallest half angle (10 deg) were difficult to operate. A restrike mode of operation was identified and described. Damage in the form of melting was observed in the constrictor region of all the nozzle inserts tested. Arcjet ignition was also difficult in many tests and a glow discharge mode that prevents starting was identified.

Curran, Francis M.↗

Study of Forming of Magnesium Alloy by Explosive Energy

Magnesium alloy is an attractive next generation material due to its high specific strength with low weight. However, magnesium alloys has few slip lines with close-packed hexagonal lattice, and generally poor ductility at room temperature, therefore it is difficult to form this material by cold forging. It is well known that the speed of deformation of metallic materials rapidly changes at the high strain rate. For some metallic materials, it is reported that the ductility also increases at the high strain rate with this speed effect. In this study, a series of high speed impulsive compressive tests were carried. By using explosives for shock wave loading, the velocity in this experiment reached 100 m/s that can't be easily obtained in normal experiment. In this paper, the possibility of forming the AZ31 extrusion magnesium alloy using explosive-impulsive pressure is investigated. And improved ductility by the effect of high-rate deformation is observed with this alloy.

36 MATERIALS SCIENCE↗

Electrospray Thruster Performance with Microfabricated Emitter Arrays and Indium Propellant

The feasibility of a microfabricated indium-fueled electrospray thruster with excellent performance was demonstrated. High efficiency electrospray thrusters with microfabricated components are under development for very compact, distributable propulsion systems that can be employed on both very small and large spacecraft with 10X improvement over SOA in mass, volume and specific impulse The critical components of this technology are the microfabricated emitter arrays and the capillary force driven indium feed system. Grey scale electron-beam lithography patterning and reactive ion dry etching provided the required micron-scale etch precision and uniformity across an array of 400 emitters in 1 cm2. Initial tests of single microfabricated silicon emitters demonstrated better performance than industry standard single emitters and the performance required to achieve 200 micronewtons when scaled up to a thruster with 400 emitters in 1 cm2. Arrays of emitters tested in a preliminary prototype Microfluidic Electrospray Propulsion (MEP) thruster assembly demonstrated stable performance at estimated thrust levels of 5, 50, and 120 µN at extraction voltages less than 4 kV. Current stability was within 0.15 % at 120 µN with only 1.5% of the emitter current collected by the extractor electrode. Post-test inspections revealed that more than 99% of the 400 emitters were electrospraying during the test. Specific impulse was estimated to be >3100 s from measurements of total charge and consumed indium mass at an emitter voltage of 1470 V. The results of this investigation suggest that microfabricated indium electrospray thruster technology is both feasible and capable of excellent performance as a highly compact microthruster.

Marrese-Reading, Colleen M.↗

Ground vibration test results of a JetStar airplane using impulsive sine excitation

Structural excitation is important for both ground vibration and flight flutter testing. The structural responses caused by this excitation are analyzed to determine frequency, damping, and mode shape information. Many excitation waveforms have been used throughout the years. The use of impulsive sine (sin omega t)/omega t as an excitation waveform for ground vibration testing and the advantages of using this waveform for flight flutter testing are discussed. The ground vibration test results of a modified JetStar airplane using impulsive sine as an excitation waveform are compared with the test results of the same airplane using multiple-input random excitation. The results indicated that the structure was sufficiently excited using the impulsive sine waveform. Comparisons of input force spectrums, mode shape plots, and frequency and damping values for the two methods of excitation are presented.

Kehoe, Michael W.↗

Ground vibration test results of a JetStar airplane using impulsive sine excitation

Structural excitation is important for both ground vibration and flight flutter testing. The structural responses caused by this excitation are analyzed to determine frequency, damping, and mode shape information. Many excitation waveforms have been used throughout the years. The use of impulsive sine (sin omega t)/omega t as an excitation waveform for ground vibration testing and the advantages of using this waveform for flight flutter testing are discussed. The ground vibration test results of a modified JetStar airplane using impulsive sine as an excitation waveform are compared with the test results of the same airplane using multiple-input random excitation. The results indicated that the structure was sufficiently excited using the impulsive sine waveform. Comparisons of input force spectrums, mode shape plots, and frequency and damping values for the two methods of excitation are presented.

Kehoe, Michael W.↗

Measurements of Picosecond Energy Equilibration in Isochorically Heated Materials

In this Final Report we present the results of our DOE/FES-sponsored research on rapidly heated materials. The research focused on the details of picosecond energy equilibration and material response to isochoric heating by relativistic (or “hot”) electrons. The major goal was to improve the understanding of these processes by making time-resolved extreme ultraviolet (XUV) measurements of ultrafast energy deposition and blast-wave formation for testing impulsive-heating models in extreme thermodynamic conditions. Major achievements of the project include the design, fabrication, deployment, and use of two XUV spectrometers on the Multi-Terawatt (MTW) Laser System at the University of Rochester’s Laboratory for Laser Energetics. One of the spectrometers is coupled to an x-ray charge-coupled device (CCD) for time-integrated measurements; the other is coupled to an ultrafast x-ray streak camera for time-resolved measurements. Working together, these instruments provide absolutely calibrated data on the emitted XUV spectrum from an isochoric heated target. The new diagnostic system was used to measure and infer the time-resolved rear-surface temperature and density for different target materials and different target-interaction conditions. Experiments with laser-heated metal foils measured the ultrafast dynamics and energy deposition from hot electrons into plasma heating and blast-wave formation. The blast wave was observed emerging from the rear surface of the laser-irradiated target. The time between the prompt emission (electron-driven x-ray emission) and the blast-wave arrival was used to estimate the energy deposition into the wave. The data are consistent with a Sedov–Taylor blast wave, with energy transfer from the laser to the blast of up to 20 mJ. The data represent the first quantitative assessment of the blast-wave energy in a metal following heating by a short burst of high-intensity laser-generated hot electrons. The funding from this grant provided significant opportunities for training and professional development. The grant supported or partially supported a graduate student, a postdoctoral research associate, and a senior staff scientist. This support included bringing together a dedicated group of individuals with a niche set of experimental and theoretical skills for studying advanced material properties experiments and ultrafast radiation conditions. The team dynamic fostered training and knowledge transfer across the whole spectrum of research activities through shared experiences in advanced laboratory techniques, data analysis, modeling, and the development of new ideas, techniques, presentations, and publications. The results of this work, which significantly improve the understanding of rapid energy deposition in solid matter, have been widely disseminated to communities of interest through invited talks, contributed talks, and peer-reviewed journals.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗