Results for “in-the-loop” — Page 3

NASA NTRS2014

UAS Measured Response: The Effect of GCS Control Mode Interfaces on Pilot Ability to Comply with ATC Clearances

This presentation summarizes the background and primary findings from a study on UAS (Unmanned Aerial Systems) pilots' ability to get 'in-the-loop' when responding to air traffic controller clearances around traffic and weather. Pilots controlled a simulated UAS using three different control mode interfaces: a waypoint-to-waypoint interface, an auto-pilot interface (which allowed heading and altitude holds), and a manual stick-and-throttle interface. Pilots' response times were compared across the three conditions, with the waypoint-to-waypoint interface resulting in the slowest pilot performance in several of the metrics. Conclusions from these findings and limitations of the study are discussed.

Measured Response↗

NASA NTRS2019

Piloted Full-Motion Simulation in Simulink®

A recent experiment at NASA Ames Research Center’s Vertical Motion Simulator (VMS) successfully combined a real-time, human in-the-loop architecture with the flexibility of operating in the Simulink® graphical model-based engineering environment. The VMS is a large amplitude flight simulator designed to be adaptable to provide rapid integration and development of a wide variety of vehicles and support diverse aeronautical investigations. Math models are often programmed in Simulink. Typically, to run Simulink models in real time, they are converted to C code. However, the conversion and integration process can be time consuming and cumbersome. Thus, the VMS facility capabilities were expanded to allow a Simulink vehicle math model to run in the MathWorks’ MATLAB environment during a piloted full-motion simulation experiment. The MATLAB Simulink based approach to driving the VMS was found to decrease development time by allowing quick integration of math model changes and providing the ability to run the same version of the model on researcher’s desktop computers. This accomplishment demonstrated that the development ease of the graphical Simulink environment could be retained, while working within the real-time environment of the VMS architecture and maintaining the unique flexibility of the VMS.

Lewis, Emily K.↗

NASA NTRS2019

Integrated Flush Air Data Sensing System Modeling for Planetary Entry Guidance with Direct Force Control

Flush air data sensing (FADS) systems have been previously used at both Earth and Mars to provide onboard estimates of angle of attack, sideslip angle, and dynamic pressure. However, these FADS data were often not used in an in-the-loop sense to inform the onboard guidance and control systems. A method to integrate FADS-derived density and wind estimates with a numerical predictor-corrector guidance algorithm is presented. The method is demonstrated in a high-fidelity simulation of a human-scale Mars entry vehicle that utilizes a hypersonic inflatable aerodynamic decelerator (HIAD) with direct force control. Effects on guidance commands and state uncertainties both with and without FADS system modeling are presented and discussed.

Lugo, Rafael A.↗

NASA NTRSDate not supplied

Digital Twins and Living Models at NASA

The idea of a “digital twin” was born at NASA in the 1960s as a “living model” of the Apollo mission. In response to Apollo 13’s oxygen tank explosion and subsequent damage to the main engine, NASA employed multiple simulators to evaluate the failure and extended a physical model of the vehicle to include digital components. This “digital twin” was the first of its kind, allowing for a continuous ingestion of data to model the events leading to up to the accident for forensic analysis and exploration of next steps. Fast forward half a century and NASA, along with others in the aerospace community, continues to develop and utilize high-fidelity digital models of physical systems and components as well as the extreme environments in which they operate. NASA aims to travel further and stay longer in space as we realize the Artemis program, taking us from the moon to Mars by establishing a sustainable presence on the Moon to prepare for missions to Mars. We will no longer be able to rely on constant connectivity with an asset nor be in-the-loop for on-demand human intervention in the event of an anomaly. Further, the importance of digital twins is increasing as we seek alternatives for certification of structures so large that they cannot be fully evaluated in existing test facilities and autonomous systems that are not deterministic. The idea of a digital twin is not a new one. What is new is the scale, ordinality, and non-deterministic nature of the models that are critical to achieving NASA’s goals. Their number and autonomy from each other as well as the reference system is suggestive of a changing ecosystem, returning us the idea of a living model.

Digital Twin↗

NASA NTRSDate not supplied

Precision Landing Performance of a Human-Scale Lunar Lander Using a Generalized Simulation Framework

NASA has established goals of returning humans to Moon with an initial landing by 2024 and a subsequent sustained presence by 2028, which will require technological advances in spacecraft navigation to enable precision landing. The ability to assess the navigation performance of these new and existing technologies is critical to identifying areas of risk reduction and investment. To that end, the Safe and Precise Landing Integrated Capabilities Evolution (SPLICE) project has demonstrated that a detailed six degree-of-freedom integrated performance simulation framework can provide information on and assessment of expected navigation performance. This framework incorporates engineering models of the on-board spacecraft guidance, navigation, and control systems at varying levels of fidelity. Recent advances in the development of this integrated performance simulation permit running these systems “in-the-loop,” rather than assuming perfect knowledge of the spacecraft states. This development, coupled with fast simulation time and modularization of the various system models, enables a wide variety of system trades to be assessed at once. This paper presents a summary of the advances in the SPLICE simulation framework, updates to the spacecraft navigation models, and an application of the framework to characterize the precision landing performance of a human-scale lunar lander. A series of trade studies examining effects of ground state update qualities shows that given all other assumptions, sufficiently accurate Deep Space Network (DSN) measurements can enable safe and precise human-scale Lunar landings.

Spacecraft navigation↗

NASA NTRS2022

IRIS: High-fidelity Perception Sensor Modeling for Closed-Loop Planetary Simulations

Perception plays a key role in autonomous and semi-autonomous planetary exploration vehicles. For instance, landers can use computer vision techniques for identifying safe landing locations, aerial vehicles use cameras as navigation sensors, and planetary rovers use them for localization and hazard detection. Engineering simulations of such systems requires the accurate modeling of perception and vision sensors for simulating autonomy scenarios. In addition, the modeling of sensors for landers, aerial and ground vehicles requires the ability to handle large and high-resolution terrains, the accurate modeling of illumination, hi-fidelity rendering via ray/path tracing and the inclusion of sensor characteristics. Vision sensor models strive to simulate sensor reality by using physics principles to model the interaction of light and objects. Furthermore, high frame rate performance is highly desirable for in-the-loop simulations involving vehicle dynamics and control software. In this paper we describe a new sensor modeling capability called Inter-planetary Rendering for Imaging and Sensors (IRIS) that meets these requirements for the real-time and high-fidelity simulation of vision sensors for planetary aerospace and robotics applications.

Elmquist, Asher↗

NASA NTRS2022

Precision Landing Performance and Technology Assessments of a Human-Scale Lunar Lander Using a Generalized Simulation Framework

NASA has established goals of returning humans to Moon with an initial landing by 2024 and a subsequent sustained presence by 2028, which will require technological advances in spacecraft navigation to enable precision landing. The ability to assess the navigation performance of these new and existing technologies is critical to identifying areas of risk reduction and investment. To that end, the Safe and Precise Landing Integrated Capabilities Evolution (SPLICE) project has demonstrated that a detailed six degree-of-freedom integrated performance simulation framework can provide information on and assessment of expected navigation performance. This framework incorporates engineering models of the on-board spacecraft guidance, navigation, and control systems at varying levels of fidelity. Recent advances in the development of this integrated performance simulation permit running these systems “in-the-loop,” rather than assuming perfect knowledge of the spacecraft states. This development, coupled with fast simulation time and modularization of the various system models, enables a wide variety of system trades to be assessed at once. This paper presents a summary of the advances in the SPLICE simulation framework, updates to the spacecraft navigation models, and an application of the framework to characterize the precision landing performance of a human-scale lunar lander. A series of trade studies examining effects of ground state update qualities shows that given all other assumptions, sufficiently accurate Deep Space Network (DSN) measurements can enable safe and precise human-scale Lunar landings.

"D'Souza, Sarah", 'Pensado, Alegandro R.↗

NASA NTRSDate not supplied

Parallel Hybrid Turboprop Performance Modeling and Optimization

NASA’s Electrified Powertrain Flight Demonstration (EPFD) project conducts ground and flight tests of integrated Megawatt (MW) class hybrid-electric powertrain systems on regional turboprop aircraft demonstrators. To meet the increased demand for assessment of potential capabilities and benefits from these novel vehicle configurations, NASA is developing tooling and models to estimate the performance of hybridized regional turboprops. This paper covers the development of a parametrically driven performance model for a De Havilland Canada Dash 8-400 (Q400) regional turboprop integrated with a novel parallel hybrid architecture using the Gascon framework. Gascon is a modern reimplementation of the General Aviation Synthesis Program (GASP) built using the Condor mathematical modeling framework in Python. Within Gascon, a parametric representation of the parallel hybrid architecture was synthesized, which features the electric motor coupled to the power turbine. This capability allows for in-the-loop optimization of the parametric parallel hybrid architecture to characterize the mission capabilities and fuel savings of the design and determine optimal power scheduling strategies for efficient electric power management for a given mission. The study shows that a fuel savings of up to 20% can be achieved, but that increased fuel savings comes at the expense of payload capacity.

Gascon↗

NASA NTRSDate not supplied

Parallel Hybrid Turboprop Performance Modeling and Optimization

NASA’s Electrified Powertrain Flight Demonstration (EPFD) project conducts ground and flight tests of integrated Megawatt (MW) class hybrid-electric powertrain systems on regional turboprop aircraft demonstrators. To meet the increased demand for assessment of potential capabilities and benefits from these novel vehicle configurations, NASA is developing tooling and models to estimate the performance of hybridized regional turboprops. This paper covers the development of a parametrically driven performance model for a De Havilland Canada Dash 8-400 (Q400) regional turboprop integrated with a novel parallel hybrid architecture using the Gascon framework. Gascon is a modern reimplementation of the General Aviation Synthesis Program (GASP) built using the Condor mathematical modeling framework in Python. Within Gascon, a parametric representation of the parallel hybrid architecture was synthesized, which features the electric motor coupled to the power turbine. This capability allows for in-the-loop optimization of the parametric parallel hybrid architecture to characterize the mission capabilities and fuel savings of the design and determine optimal power scheduling strategies for efficient electric power management for a given mission. The study shows that a fuel savings of up to 20% can be achieved, but that increased fuel savings comes at the expense of payload capacity.

Gascon↗

DOE OSTI2021

ARIES: Advanced Research on Integrated Energy Systems Research Plan

The Advanced Research on Integrated Energy Systems (ARIES) platform is one of the most powerful research environments anywhere for addressing the speed and scale of change on power systems. This research plan details ARIES capabilities, current and upcoming, and how they relate to objectives for advanced energy systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗

NASA NTRSDate not supplied

Desert Research and Technology Studies (D-RATS) 2022 Quicklook Report

This report summarizes the Desert Research and Technology Studies (D-RATS) 2022 analog tests. BACKGROUND - Artemis Challenges – NASA’s concept of operations (ConOps) for the Artemis mission architecture brings new challenges for human exploration of the lunar surface, including: (1) Low-angle, natural lighting at lunar poles; and (2) Exploration sites that challenge communication with Earth. - International Partner Involvement – NASA is working with the Japan Aerospace Exploration Agency (JAXA) to scope mission & functional requirements for an Artemis Pressurized Rover (PR), which JAXA may provide. - Charter – HQ Exploration Systems Development Mission Directorate (ESDMD) Moon to Mars Architecture Development Office (M2MADO) Strategy and Architectures (SA) chartered the Human-in-the-Loop (HITL) test team to investigate Artemis architectural questions related to pressurized rover ConOps. - Rationale – to inform the NASA/JAXA pressurized rover study-agreement. PLAN - Objectives – Analog tests conducted in October 2022 by the D-RATS team addressed three high-level objectives: 1. Investigate pressurized rover (PR) ConOps and capabilities for Artemis exploration 2. Integrate with JAXA engineers & astronauts and incorporate JAXA PR design elements into testing. 3. Re-establish analog field-testing skills & capabilities with rovers to investigate Artemis architecture ConOps. - Secondary Objectives – Work with other groups to leverage D-RATS field test for additional objectives. 4. Work with the Public Affairs Office (PAO) to perform D-RATS public outreach activities. 5. Coordinate with the Human Physiology Performance Protection & Operations (H-3PO) team to facilitate in-field evaluation of human health and performance (HHP) objectives. 6. Share D-RATS field-site and assets with Lunar LTE Studies (Lunar LiTES) team, to aid their study of the use of 4G/LTE communication protocols and devices for astronauts and robotic nodes on the lunar surface. - Team – Fully integrated test team comprised of members from 5 NASA centers, JAXA, and the United States Geological Survey (USGS) - Location – Black Point Lava Flow, ~40 miles north of Flagstaff, AZ HIGH-LEVEL OBJECTIVES ACCOMPLISHED - Investigated Pressurized Rover ConOps & Capabilities for Artemis Exploration (Objective 1) - Completed testing with 4 crew pairs, each spending 3 days and 2 nights in the rover conducting Artemis PR dayin-the-life activities (2 JAXA astronauts, 2 JAXA engineers, 1 NASA astronaut, 3 NASA engineers). - Collected detailed objective & subjective data supporting 10 strategic questions related to Artemis PR operations. - Field geologists present in field observed rover operations & EVAs. - Science team in Houston MCC communicated directly with crew. - Demonstrated crew-led and MCC-led PR teleoperation use cases during EVAs. - Integrated with JAXA Engineers & Astronauts and Incorporated JAXA PR Design Elements into Testing (Objective 2) - NASA & JAXA engineers, flight controllers, scientists, roboticists, and astronauts directly participated in and/or observed testing both in field and in MCC-Houston. - Incorporated JAXA PR design elements into both integrated and standalone testing at JSC and in the field. - Re-established Analog Field-Testing Skills & Capabilities with Rovers to Investigate Artemis Architecture ConOps (Objective 3) - Multiple teams successfully worked to establish and manage field-test base camp, monitor and maintain the rover, and plan and execute 2 weeks of consecutive field-testing with little to no breaks between crews. TEST OUTCOMES - Results will inform Artemis architecture ConOps & capabilities related to pressurized rover operations (see sections 2 for more details) - Summary and team detailed reports will be posted on the D-RATS 2022 wiki

Analog↗