Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface reinforcement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Bio-treatment of poplar via amino acid for interface control in biocomposites

Advanced biocomposites reinforced by abundant biomass-derived fillers can add a revenue stream to enhance the economic viability of biofuel production chains and the energy efficiency of the composite industry. However, the low stiffness of biopolymers limits their use in structural applications. Poplar fibers (mesh size: <180 μm, Populus spp.), an abundant waste from the wood industry, were used as bio-filler to fabricate high-performance biocomposites based on polylactic acid (PLA), in which the poplar fibers were modified by an amino acid (l-lysine). As a benefit of the amino acid treatment, the tensile Young's moduli of the lysine/poplar/PLA composites increased by up to 68% with the addition of a small amount of lysine, compared with neat PLA. At the same time, the tensile strength, failure strain, and Young's modulus of the poplar/PLA composites all increased after adding only 0.1 wt % of lysine. It has been observed that the lysine content has a significant effect on the decomposition temperature, complex viscosity, storage modulus, crystallization temperature, and crystallinity of composites. The fracture surfaces of the composites with an optimum lysine content had fewer voids and were more compact compared with composites without any lysine. The pores on the surfaces of poplar fibers became more available for the penetration of PLA molecules as a result of lysine addition. Finally, this study presents a facile method for reinforcing biocomposites with extremely low-cost and environmentally friendly biofillers.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Unraveling disadhesion mechanism of epoxy/CSH interface under aggressive conditions

Almost all FRP-reinforced concrete exposed to the marine environment are susceptible to durability deficiencies due to failure of the FRP/epoxy/concrete interface, especially the vulnerable epoxy/concrete interface, which is frequently attacked by water and ions. Herein, molecular dynamics simulations of epoxy/CSH interface under different environmental exposures are utilized to specifically elucidate the degradation principles of water and ions on the bonding properties and mechanical responses of the epoxy/concrete interface. The environmental sequences associated with the interfacial bonding degradation are arranged as Na{sub 2}SO{sub 4} + NaCl>NaCl>Na{sub 2}SO{sub 4} > Water>Dry. Remarkably, water molecules weaken the interaction between the epoxy and CSH by robbing interfacial H- and Ca-O bonds, thereby reducing the energy barrier to interfacial peel and shear failure. The weakening effects are exacerbated by the presence of aggressive ions, as Na{sup +} ions attracted to the CSH surface accumulate more water molecules in the interfacial region by forming hydrated ions clusters, which ultimately accelerates the epoxy/CSH interfacial degradation.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Fiber-matrix interface failures

Interface fractures of aluminum-graphite composites under transverse loading are expected to occur within the graphite fibers, but very near the interface. Residual stresses in aluminum, reinforced with the new high modulus pitch-based fibers, are much lower than would be expected based on simple elasticity calculations. The excess stress may be relaxed by shearing internal to the fibers or at the interface rather than by plastic flow of the matrix. The internal shearing also occurs during repeated thermal cycling of these composites; the fibers are repeatedly intruded, then extruded, during repeated temperature excursions.

Rabenberg, Lew↗
DOE OSTI2022

The Roles of Interface, Adherend, and Adhesive in Plasma- and Other-treated Joints of Metals and FRP Materials Under Shear Deformation

This work investigated the role of interface, adherend, and adhesive in adhesively-bonded metal-metal, metal-CFRTP, and CFRTP-CFRTP combinations with plasma-treated surfaces under shear deformation. To this end, aluminum alloys (AA5052 and AA6061) and short-carbon-fiber-reinforced polyamide 66 (CFRPA66) were used as examples and performed through single lap shear testing. The results showed that air plasma surface treatment can improve the shear behavior of adhesively-bonded AA5052-CFRPA66 and CFRPA66-CFRPA66 joints with about 20% enhanced lap shear strength compared to non-treated cases. Failure surface morphology of plasma-treated CFRPA66 adherend confirmed this improvement by showing an increased amount of adhesive failure than interfacial failure between CFRPA66 and adhesive. But this is not true for AA5052-AA6061 joints with plasma-treated surfaces exhibiting almost no enhanced lap shear strength. This study also showed the importance of selecting a proper surface modification method for the enhancement of adhesive-bonded structures under shear deformation through the analysis of the results in this study and in the literature. For fiber-reinforced polymers (FRPs), improving FRP/adhesive interface may be prioritized via different surface modification methods (e.g., plasma, chemical coating, etc.) than adhesive modification methods. However, for surface-cleaned metals, toughening adhesive via different enhancement methods (e.g., nano-particles, chemical enhancement, etc.) may be more important than improving metal/adhesive interface. These insightful results are valuable in the area of multi-materials joining.

Qiao, Yao↗
NASA NTRS1975

An investigation of the compressive strength of Kevlar 49/epoxy composites

Tests were performed to evaluate the effect of a wide range of variables including matrix properties, interface properties, fiber prestressing, secondary reinforcement, and others on the ultimate compressive strength of Kevlar 49/epoxy composites. Scanning electron microscopy is used to assess the resulting failure surfaces. In addition, a theoretical study is conducted to determine the influence of fiber anisotropy and lack of perfect bond between fiber and matrix on the shear mode microbuckling. The experimental evaluation of the effect of various constituent and process characteristics on the behavior of these unidirectional composites in compression did not reveal any substantial increase in strength. However, theoretical evaluations indicate that the high degree of fiber anisotropy results in a significant drop in the predicted stress level for internal instability. Scanning electron microscope data analysis suggests that internal fiber failure and smooth surface debonding could be responsible for the measured low compressive strengths.

Kulkarni, S. V.↗
NASA NTRS1990

Local stresses in metal matrix composites subjected to thermal and mechanical loading

An elasticity solution has been used to analyze matrix stresses near the fiber/matrix interface in continuous fiber-reinforced metal-matrix composites, modeling the micromechanics in question in terms of a cylindrical fiber and cylindrical matrix sheath which is embedded in an orthotropic medium representing the composite. The model's predictions for lamina thermal and mechanical properties are applied to a laminate analysis determining ply-level stresses due to thermomechanical loading. A comparison is made between these results, which assume cylindrical symmetry, and the predictions yielded by a FEM model in which the fibers are arranged in a square array.

Highsmith, Alton L.↗
NASA NTRS2017

Direct Measurements of the Mechanical Strength of Carbon Nanotube - Aluminum Interfaces

Interfacial load transfer plays a critical role in the bulk mechanical performance of nanofiber-reinforced metallic-matrix nanocomposites (MMNC). In this paper, we investigate the mechanical strength of interfaces in double-walled carbon nanotube (CNT)-reinforced aluminum (Al) nanocomposites by using in situ electron microscopy nanomechanical single-tube pull-out techniques. The nanomechanical measurements reveal the shear lag effect on the CNT-Al interface that is found to possess an average interfacial shear strength (IFSS) of about 28.7 MPa. The study also shows that thermal annealing results in substantially higher binding strength interfaces between CNTs and Al matrices. The average IFSS of CNT-Al interfaces that were thermally annealed at 400 °C is found to reach about 35.3 MPa, a 23% increase from that of the non-annealed interfaces. The maximum load bearing capacity of the annealed interfaces reaches about 304 nN, a 40.1% increase from that of the non-annealed ones (about 217 nN). The findings are useful to better understand the load transfer mechanism in CNT-reinforced MMNC and the tuning and optimization of the reinforcing performance through thermal processing.

Interfacial strength↗
NASA NTRS1990

Influence of interfacial shear strength on the mechanical properties of SiC fiber reinforced reaction-bonded silicon nitride matrix composites

The influence of fiber/matrix interface microstructure and interfacial shear strength on the mechanical properties of a fiber-reinforced ceramic composite was evaluated. The composite consisted of approximately 30 vol percent uniaxially aligned 142 microns diameter SiC fibers (Textron SCS-6) in a reaction-bonded Si3N4 matrix (SiC/RBSN). The interface microstructure was varied by controlling the composite fabrication conditions and by heat treating the composite in an oxidizing environment. Interfacial shear strength was determined by the matrix crack spacing method. The results of microstructural examination indicate that the carbon-rich coating provided with the as-produced SiC fibers was stable in composites fabricated at 1200 C in a nitrogen or in a nitrogen plus 4 percent hydrogen mixture for 40 hr. However this coating degraded in composites fabricated at 1350 C in N2 + 4 percent H2 for 40 and 72 hr and also in composites heat treated in an oxidizing environment at 600 C for 100 hr after fabrication at 1200 C in a nitrogen. It was determined that degradation occurred by carbon removal which in turn had a strong influence on interfacial shear strength and other mechanical properties. Specifically, as the carbon coating was removed, the composite interfacial shear strength, primary elastic modulus, first matrix cracking stress, and ultimate tensile strength decreased, but the first matrix cracking strain remained nearly the same.

Bhatt, Ramakrishna T.↗
NASA NTRS1990

Thermal and mechanical behavior of metal matrix and ceramic matrix composites

The present conference discusses local stresses in metal-matrix composites (MMCs) subjected to thermal and mechanical loads, the computational simulation of high-temperature MMCs' cyclic behavior, an analysis of a ceramic-matrix composite (CMC) flexure specimen, and a plasticity analysis of fibrous composite laminates under thermomechanical loads. Also discussed are a comparison of methods for determining the fiber-matrix interface frictional stresses of CMCs, the monotonic and cyclic behavior of an SiC/calcium aluminosilicate CMC, the mechanical and thermal properties of an SiC particle-reinforced Al alloy MMC, the temperature-dependent tensile and shear response of a graphite-reinforced 6061 Al-alloy MMC, the fiber/matrix interface bonding strength of MMCs, and fatigue crack growth in an Al2O3 short fiber-reinforced Al-2Mg matrix MMC.

Kennedy, John M.↗
NASA NTRS1986

Interfaces and failure mechanisms in Al-SiC composites

Aluminum alloys reinforced with silicon carbide whiskers exhibit significantly higher strength and modulus than the unreinforced alloys. However, the composites also exhibit low ductility and poor fracture toughness for reasons which are not well-understood. In this study, high resolution and conventional TEM techniques are used to analyze interface microstructure and failure mechanisms in P/M 2124 and 6061 aluminum alloys reinforced with silicon carbide whiskers. Interfacial oxides are typical of both composite materials, often distributed in clusters or in a discrete layer 2-5 nm thick along the whisker-matrix interface. Highly deformed regions beneath bulk tensile fracture surfaces reveal possible fracture nucleation centers as well as sites of stress concentration where intense plastic strain has occurred. Observations of such highly deformed regions include (1) void initiation at whisker ends, (2) interface decohesion involving the thin oxide layer, (3) transverse cracks in whiskers, and (4) cracks in large constituent particles. TEM results are presented and discussed in relation to mechanisms of composite failure.

Nutt, S. R.↗
NASA NTRS1990

Fatigue damage growth mechanisms in continuous fiber reinforced titanium matrix composites

The role of fiber/matrix interface strength, residual thermal stresses, and fiber and matrix properties on fatigue damage accumulation in continuous fiber metal matrix composites (MMC) is discussed. Results from titanium matrix silicon carbide fiber composites is the primary topic of discussion. Results were obtained from both notched and unnotched specimens at room and elevated temperatures. The stress in the 0 deg fibers was identified as the controlling factor in fatigue life. Fatigue of the notched specimens indicated that cracks can grow in the matrix materials without breaking fibers.

Johnson, W. S.↗
NASA NTRS1990

Fatigue damage growth mechanisms in continuous fiber reinforced titanium matrix composites

The role of fiber/matrix interface strength, residual thermal stresses, and fiber and matrix properties on fatigue damage accumulation in continuous fiber metal matrix composites (MMC) will be discussed. Results from titanium matrix/silicon-carbide fiber composites will be the primary topic of discussion. Results have been obtained from both notched and unnotched specimens at room and elevated temperatures. The stress in the 0 deg fibers has been indentified as the controlling factor in fatigue life. Fatigue of the notched specimens indicated that cracks can grow many fiber spacings in the matrix materials without breaking fibers.

Johnson, W. S.↗
NASA NTRS1998

Effects of Fiber/Matrix Interface and its Composition on Mechanical Properties of Hi Nicalon/Celsian Composites

Fiber-reinforced ceramic matrix composites (CMC) are prospective candidate materials for high temperature structural applications in aerospace, energy conservation, power generation, nuclear, petrochemical, and other industries. At NASA Lewis, we are investigating celsian matrix composites reinforced with various types of silicon carbide fibers. The objective of the present study was to investigate the effects of fiber/matrix interface and its composition on the mechanical properties of silicon carbide (Hi-Nicalon) fiber-reinforced celsian matrix composites.

Bansal, Narottam P.↗
DOE OSTI2023

Hemp fiber reinforced dual dynamic network vitrimer biocomposites with direct incorporation of amino silane

Natural fiber composites are inexpensive and renewable alternatives to traditional fiber reinforced polymers (FRPs). However, existing natural fiber composites primarily rely on petrochemical based thermosetting matrices, which are difficult to recycle due to their stable crosslinked network structures. To address this challenge, it is desirable to develop natural fiber composites with inherently recyclable biobased matrices. In this study, we developed a dual dynamic network vitrimer matrix from hempseed oil and limonene derivatives and demonstrated its application in hemp fiber reinforced composites. To improve the weak interface between hemp fiber and the polymer matrix, a common challenge in the realm of natural fiber composites, we directly incorporated amino silane into the vitrimer matrix. The amino silane participated in the polymer network, increasing the crosslink density and toughening the matrix, as evidenced by a significantly improved impact strength from 3.5 kJ/m 2 to 10.3 kJ/m 2 . Moreover, the incorporation of amino silane resulted in a lower water absorption by 11% in 7-day soaking for the composites, demonstrating improved fiber/matrix interfacial interaction. Furthermore, our biobased vitrimer matrix exhibits both imine and hydroxy-ester dynamic bonds, which enable the recycling of the biocomposite through a mild and cost-effective aminolysis process (100°C, 3h, ambient pressure). The decomposed polymer matrix was successfully reused as a polyol for polyurethane adhesives, and the surface morphology of recovered hemp fibers was analyzed and compared with that of the original fibers. Furthermore, these findings will help broaden the use of vitrimers for practical natural fiber composite applications, raise awareness of the problem of recycling natural fiber composite waste, and shed light on the interfacial challenge of natural fiber reinforced vitrimer composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1988

Reaction kinetics between fiber and matrix

Interdiffusion and interdiffusion controlled intermediate phase formation in metal matrix composites can be of interest for the prolonged application of these systems at high temperatures. Methods are discussed that address the kinetics of interdiffusion in systems that exhibit solid solution intermixing or the formation of a third intermediate phase at the fiber/matrix interface, or both. The tungsten fiber reinforced niobium and tungsten fiber reinforced superalloy systems are employed as model systems for experimentation and discussion. In an effort to impede interdiffusion, the concept of ion implanted diffusion barriers have been examined. Preliminary results on the feasibility and effectiveness of ion implanted diffusion barriers are presented.

Kopp, M. W.↗
NASA NTRS2005

Solid Oxide Fuel Cell Seal Glass - BN Nanotubes Composites

Solid oxide fuel cell seal glass G18 composites reinforced with approx.4 weight percent of BN nanotubes were fabricated via hot pressing. Room temperature strength and fracture toughness of the composite were determined by four-point flexure and single edge V-notch beam methods, respectively. The strength and fracture toughness of the composite were higher by as much as 90% and 35%, respectively, than those of the glass G18. Microscopic examination of the composite fracture surfaces using SEM and TEM showed pullout of the BN nanotubes, similar in feature to fiber-reinforced ceramic matrix composites with weak interfaces. Other mechanical and physical properties of the composite will also be presented.

Bansal, Narottam P.↗
DOE OSTI2021

The Role of Interface in Additively Manufactured Interpenetrating Composites

Additively Manufactured Interpenetrating Composites (AMIPCs) are a relatively new metal-metal chain composite in development for use in high energy absorption systems. In this system, reinforcing phase of additively manufactured continuous lattice configurations 316L austenitic stainless-steel is in melt infiltrated with a matrix phase of A356 aluminum-silicon casting alloy. Measurements and observations of this material system have shown that weakly bonded or open/porous interface between the reinforcement and matrix phases exhibits dramatically different mechanical properties of AMIPCs, which is not currently well understood. In this work, Finite Element Models (FEM) are used to model the effects of interfaces between the composite phases. Mechanical tensile tests measurements of various composite volume fractions and varying degrees of casting infiltration are also examined and used to show consistency with the FEM results. The outcome provides insight into material design criteria and performance predictions for new hybrid material systems with exceptional damage tolerance.

Allen, Jason↗
DOE OSTI2021

Functional Mock-up Interface - Machine Learning Center (FMI-MLC) v1

The Functional Mock-up Interface - Machine Learning Center is a tool to interface the Python-Tensorflow library with building simulation models, to develop and train machine learning-based controls. In particular, this framework allows the use of reinforcement learning through the standardized Functional Mock-up Interface, an open industry standard for co-simulation. First application was the development of a controller for dynamic façade and heating ventilation and air conditioning (HVAC) systems.

Gehbauer, Christoph↗