Search NASA⌕ Search

SEARCH · Search NASA

Results for “interlocking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Toughness properties of a three-dimensional carbon-epoxy composite

The three-dimensional (3D) orthogonal interlocked fabric contains through-the-thickness reinforcement in order to enhance the interlaminar fracture toughness of the composite. The interlaminar fracture toughness of a carbon-epoxy orthogonal interlocked fabric composite was experimentally determined by use of the recently developed tabbed double cantilever beam specimen. The data reduction methods applicable to these tests and materials and the interpretation of the results were discussed. The results of critical strain energy release rate, G(IC), were compared to those of a two-dimensional (2D) laminate having the same in-plane structure. The energy-dissipating crack propagation processes were described. The in-plane fracture toughness of the three-dimensional fabric was experimentally measured and compared to that of the two-dimensional laminate. The through-the-thickness fibers were found to create a tenfold increase in interlaminar toughness, and a 25-percent improvement in the in-plane fracture toughness.

Guenon, Valerie↗
NASA NTRS1990

Braided composite bore evacuator chambers for tank cannons

Typically, continuous filament composite components are fabricated using a filament winding technique. In this operation, fibers are introduced to a rotating mandrel while a guide holding the material traverses back and forth to place the material in a helical pattern over the surface of the mandrel. This procedure is continued until complete coverage is obtained. An alternative method for fabricating continuous filament composite components is braiding. In the braiding operation a mandrel is traversed through the center of the braider while 144 strands of material traverse around a carrier ring. As the fibers are applied to a mandrel surface, 72 carriers holding the fibers travel clockwise, while another 72 carriers travel counterclockwise to interlock fibers. An additional 72 carriers located on the back of the braider introduce longitudinal fibers to the composite giving the composite lateral strength. The goal of using the braider is to reduce production time by simultaneously applying 144 strands of material onto a mandrel as opposed to the four-strand wrapping most filament winding techniques offer. Benefits to braiding include the ability to (1) introduce longitudinal fibers to the composite structure; (2) fabricate non-symmetric components without using complex functions to produce full coverage; and (3) produce a component with a higher degree of damage tolerance due to the interlocking of fibers. The fabrication of bore evacuator chambers for a tank cannon system is investigated by utilizing a 144 carrier braiding machine, an industrial robot, and a resin applicator system.

Wheeler, Philip C.↗
NASA NTRS1991

Micromechanics of fatigue in woven and stitched composites

The goal is to determine how microstructural factors, especially the architecture of microstructural factors, control fatigue damage in 3D reinforced polymer composites. Test materials were fabricated from various preforms, including stitched quasi-isotropic laminates, and through-the-thickness angle interlock, layer-to-layer angle interlock, and through-the-thickness stitching effect weaves. Preforms were impregnated with a tough resin by a special vacuum infiltration method. Most tests are being performed in uniaxial compression/compression loading. In all cases to date, failure has occurred not by delamination, but by shear failure, which occurs suddenly rather than by gradual macroscopic crack growth. Some theoretical aspects of bridging are also examined.

Cox, B. N.↗
NASA NTRS1992

Comparison of resin film infusion, resin transfer molding, and consolidation of textile preforms for primary aircraft structure

Innovative design concepts and cost effective fabrication processes were developed for damage tolerant primary structures that can perform at a design ultimate strain level of 6000 micro inch/inch. Attention focused on the use of textile high performance fiber reinforcement concepts that provide improved damage tolerance and out-of-plane load capability, low cost resin film infusion (RFI) and resin transfer molding (RTM) processes, and thermoplastic forming concepts. The fabrication of wing 'Y' spars by four different materials and/or processes methods is described: fabricated using IM7 angle interlock 0 to 90 deg woven preforms with + or - 45 deg plies stitched with Toray high strength graphite thread and processed using RFI and 3501-6 epoxy; fabricated using G40-800 knitted/stitched preforms and processed using RFI and 3501-6 epoxy; fabricated using G40-800 knitted/stitched preforms using RTM and Tactix 123/H41 epoxy; and fabricated preforms using AS4(6K)/PEEK 150 g commingled angle interlock 0 to 90 deg woven preforms with + or - 45 deg commingled plies stitched using high strength graphite thread and processed by consolidation. Structural efficiency, processability, and acquisition cost are compared.

Suarez, J.↗
NASA NTRS1992

Comparison of resin film infusion, resin transfer molding, and consolidation of textile preforms for primary aircraft structure

Under NASA's Novel Composites for Wing and Fuselage Applications (NCWFA) Program, Grumman is developing innovative design concepts and cost-effective fabrication processes for damage-tolerant primary structures that can perform at a design ultimate strain level of 6000 micro-inch/inch. Attention has focused on the use of textile high-performance fiber-reinforcement concepts that provide improved damage tolerance and out-of-plane load capability, low-cost resin film infusion (RFI) and resin transfer molding (RTM) processes, and thermoplastic forming concepts. The fabrication of wing 'Y' spars by four different materials/processes methods is described: 'Y' spars fabricated using IM7 angle interlock 0/90 deg woven preforms with +/- 45 deg plies stitched with Toray high-strength graphite thread and processed using RFI and 3501-6 epoxy; 'Y' spars fabricated using G40-800 knitted/stitched preforms and processed using RFI and 3501-6 epoxy; 'Y' spars fabricated using G40-800 knitted/stitched preforms and processed using RTM and Tactix 123/H41 epoxy; and 'Y' spars fabricated using AS4(6k)/PEEK 150-g commingled angle interlock 0/90 deg woven preforms with +/- 45 deg commingled plies stitched using high-strength graphite thread and processed by consolidation. A comparison of the structural efficiency, processability, and projected acquisition cost of these representative spars is presented.

Suarez, J.↗
NASA NTRS2005

Thermostructural Properties Of Sic/Sic Panels With 2.5d And 3d Fiber Architectures

CMC hot-section components in advanced engines for power and propulsion will typically require high cracking strength, high ultimate strength and strain, high creep- rupture resistance, and high thermal conductivity in all directions. In the past, NASA has demonstrated fabrication of a variety of SiC/SiC flat panels and round tubes with various 2D fiber architectures using the high-modulus high-performance Sylramic-iBN Sic fiber and Sic-based matrices derived by CVI, MI, and/or PIP processes. The thermo- mechanical properties of these CMC have shown state-of-the-art performance, but primarily in the in-plane directions. Currently NASA is extending the thermostructural capability of these SiC/SiC systems in the thru-thickness direction by using various 2.5D and 3D fiber architectures. NASA is also using specially designed fabrication steps to optimize the properties of the BN-based interphase and Sic-based matrices. In this study, Sylramic-iBN/SiC panels with 2D plain weave, 2.5D satin weave, 2.5D ply-to-ply interlock weave, and 3D angle interlock fiber architectures, all woven at AITI, were fabricated using matrix densification routes previously established between NASA and GEPSC for CVI-MI processes and between NASA and Starfire-Systems for PIP processes. Introduction of the 2.5 D fiber architecture along with an improved matrix process was found to increase inter-laminar tensile strength from 1.5 -2 to 3 - 4 ksi and thru-thickness thermal conductivity from 15-20 to 30-35 BTU/ft.hr.F with minimal reduction in in-plane strength and creep-rupture properties. Such improvements should reduce thermal stresses and increase the thermostructural operating envelope for SiC/SiC engine components. These results are analyzed to offer general guidelines for selecting fiber architectures and constituent processes for high-performance SiC/SiC engine components.

Yun, H. M.↗
NASA NTRS2005

Laser Incident in the NASA Unitary Plan Wind Tunnel

A viewgraph presentation describing the laser incident in the NASA Unitary Plan Wind Tunnel (UPWT) is shown. The topics include: 1) Unitary Plan Wind Tunnel (UPWT); 2) UPWT 11' x 11' Transonic Wind Tunnel; 3) UPWT 9' x 7' Supersonic Wind Tunnel; 4) 3D Particle Image Velocimetry (PIV); 5) PIV System in 11' x 11' Transonic Test Section; 6) PIV installation in 11' x 11' TWT; 7) 3% Space Shuttle Ascent Configuration Test in UPWT 9' x 7' Test Section; 8) PIV installation in 9' x 7' SWT; 9) PIV Laser System in 9' x 7' SWT; 10) PIV Laser System Access Window; 11) Cooling Water Leak at Rear of Power Supply; 12) PIV Laser Safety Interlock System; 13) Safety Interlock Cable; 14) Q-Switch located on top of 9' x 7' Test Section; 15) Investigation Findings and Recommendations; and 16) PIV Results for 3% Space Shuttle Model in UPWT 9' x 7'.

George, Michael W.↗
NASA NTRS2001

Modular electronics packaging system

A modular electronics packaging system includes multiple packaging slices that are mounted horizontally to a base structure. The slices interlock to provide added structural support. Each packaging slice includes a rigid and thermally conductive housing having four side walls that together form a cavity to house an electronic circuit. The chamber is enclosed on one end by an end wall, or web, that isolates the electronic circuit from a circuit in an adjacent packaging slice. The web also provides a thermal path between the electronic circuit and the base structure. Each slice also includes a mounting bracket that connects the packaging slice to the base structure. Four guide pins protrude from the slice into four corresponding receptacles in an adjacent slice. A locking element, such as a set screw, protrudes into each receptacle and interlocks with the corresponding guide pin. A conduit is formed in the slice to allow electrical connection to the electronic circuit.

Hunter, Don J.↗
NASA NTRS2005

Variable-Pressure Washer

The variable-pressure washer (VPW) is a proposed device that is so named because (1) it would play the role similar to that played by an ordinary washer, except that (2) the clamping pressure applied by it would vary with either circumferential or radial position. In a typical contemplated application, the radially varying clamping pressure would be used to obtain more nearly uniform compression on a pair of concentric seals (e.g., an O-ring or a gasket) in an assembly that experiences larger deformations normal to the sealing surface for locations around the outer diameter of the attachment flange when compared to locations around the inner diameter. The VPW (see figure) would include two interlocking channel rings pushed axially away from each other by compression spring-like components located at two or more radial positions. Each spring would have a different stiffness based on the radial location. Overlapping splits in each interlocking channel ring would allow for the non-uniform deformation in the rings. Each spring would be held in place by retaining cups attached to the inner flat surfaces of the channel rings. A plunger attached to one channel ring on the central axis would be captured in a plunger housing attached to the other channel ring: The capture of the plunger would hold the VPW together. When the VPW was clamped between two flat surfaces, the clamping force would be distributed unevenly across the face of the washer in the radial direction. The different stiffnesses of the springs would be chosen, in conjunction with other design parameters, to obtain a specified radial variation of clamping pressure in the presence of a specified clamping force.

Smeltzer, Stanley S., III↗
NASA NTRS2012

Dynamically variable spot size laser system

A Dynamically Variable Spot Size (DVSS) laser system for bonding metal components includes an elongated housing containing a light entry aperture coupled to a laser beam transmission cable and a light exit aperture. A plurality of lenses contained within the housing focus a laser beam from the light entry aperture through the light exit aperture. The lenses may be dynamically adjusted to vary the spot size of the laser. A plurality of interoperable safety devices, including a manually depressible interlock switch, an internal proximity sensor, a remotely operated potentiometer, a remotely activated toggle and a power supply interlock, prevent activation of the laser and DVSS laser system if each safety device does not provide a closed circuit. The remotely operated potentiometer also provides continuous variability in laser energy output.

Gradl, Paul R.↗
NASA NTRS2015

NGSLR Safety Handbook

NASA's Next Generation Satellite Laser Ranging (NGSLR) station is the prototype for NASA's Satellite Laser Ranging (SLR) systems which will be deployed around the world in the coming decade. The NGSLR system will be an autonomous, photon-counting SLR station with an expected absolute range accuracy of better than one centimeter and a normal point (time-averaged) range precision better than one millimeter. The system provides continuous (weather permitting), 24 hour tracking coverage to an existing constellation of approximately two dozen artificial satellites equipped with passive retroreflector arrays, using pulsed, 532 nm, class IV laser systems. Current details on the approved laser systems can be found in the Appendix 1 of this document. This safety plan addresses the potential hazards to emitted laser radiation, which can occur both inside and outside the shelter. Hazards within the shelter are mitigated through posted warning signs, activated warning lights, procedural controls, personal protective equipment (PPE), laser curtains, beam blocking systems, interlock controls, pre-configured laser control settings, and other controls discussed in this document. Since the NGSLR is a satellite tracking system, laser hazards exist outside the shelter to personnel on the shelter roof and to passing aircraft. Potential exposure to personnel outside the system is mitigated through the use of posted warning signs, access control, procedural controls, a stairwell interlock, beam attenuation/blocking devices, and a radar based aircraft detection system.

satellite laser ranging↗
NASA NTRS2017

Integral Textile Structure for 3-D CMC Turbine Airfoils

An integral textile structure for 3-D CMC turbine airfoils includes top and bottom walls made from an angle-interlock weave, each of the walls comprising warp and weft fiber tows. The top and bottom walls are merged on a first side parallel to the warp fiber tows into a single wall along a portion of their widths, with the weft fiber tows making up the single wall interlocked through the wall's thickness such that delamination of the wall is inhibited. The single wall suitably forms the trailing edge of an airfoil; the top and bottom walls are preferably joined along a second side opposite the first side and parallel to the radial fiber tows by a continuously curved section in which the weave structure remains continuous with the weave structure in the top and bottom walls, the continuously curved section being the leading edge of the airfoil.

Marshall, David B.↗
NASA NTRSDate not supplied

Demonstration of Capability to Simulate Particle Irregular Shape and Poly-Disperse Mixtures Within Lunar Lander Plume-Surface Interaction

Plume-Surface Interaction (PSI) between lander engine plumes and regolith soil creates hazards in obscuration and contamination by particle clouds, high-energy ejecta streams, and landing area cratering damage. The MSFC Fluid Dynamics Branch is developing simulation tools to offer a predictive PSI capability to NASA customers such as the Human Lander System (HLS) and Commercial Lunar Payload Services (CLPS). The Gas-Granular Flow Solver (GGFS) is the main application tool for coupled gas-particle two-phase flow simulations to predict the range of PSI effects from onset of surface erosion to deep crater formation. GGFS features an Eulerian-Eulerian modeling approach, treating both gas and granular material as interacting continuum phases. Modeling the lunar regolith granular material fluidic characteristics poses special challenges due to complex particle shapes and mixture composition. The lunar regolith is poorly sorted with broad particle size distributions and large fines content. It has significant cohesion, due to interlocking jagged particle shapes. Eulerian granular material flow modeling requires closure formulations for the granular material constitutive models (stress, friction, collisional and kinetic energy dissipation, drag, etc.). While closure models for spherical particles are available from particle kinetic theory, closure models for realistic non-spherical particles must be extracted from unit physics Discrete Element Model (DEM) particle interaction simulations and provided in the form of tabular datasets. The effects of particle irregular shape (non-spherical shape factors, angular particle surface roughness, and interlocking features) are simulated by approximating the particle features in the form of grouped elemental spheres to form composite particles in the DEM simulations. The effects of the wide range of regolith mixture particle sizes and the strong effects of the presence of the small particle sizes results in high cohesion and low porosity of the regolith mixture. The range of particle sizes is simulated by binning the particle sizes into an appropriate finite number of particle-size species and solving the problem as a species mixture. Combining these two modeling approaches enables simulations to capture both, the contributions of the irregular particle shape and the particle size distribution. The integration and maturation of the DEM-based constitutive model database generation process and poly-disperse mixture binning approach into the GGFS simulation framework are proceeding under funding by the NASA Game Changing Development program. The status of current capabilities will be presented in comparisons of crater characteristics resulting for spherical and irregular shape particles, and for mono-, bi-, and tri-disperse mixture simulations of Apollo LM plume-surface interaction. The computational results confirm the significance of including the particle shape and mixture effects. Going forward plans for the full implementation of the general poly-disperse regolith modeling capability and maturation towards NASA project application readiness under the GCD program will be presented.

Peter A Liever↗
NASA NTRSDate not supplied

Demonstration of Capability to Simulate Particle Irregular Shape and Poly-Disperse Mixtures Within Lunar Lander Plume-Surface Interaction

Plume-Surface Interaction (PSI) between lander engine plumes and regolith soil creates hazards in obscuration and contamination by particle clouds, high-energy ejecta streams, and landing area cratering damage. The MSFC Fluid Dynamics Branch is developing simulation tools to offer a predictive PSI capability to NASA customers such as the Human Lander System (HLS) and Commercial Lunar Payload Services (CLPS). The Gas-Granular Flow Solver (GGFS) is the main application tool for coupled gas-particle two-phase flow simulations to predict the range of PSI effects from onset of surface erosion to deep crater formation. GGFS features an Eulerian-Eulerian modeling approach, treating both gas and granular material as interacting continuum phases. Modeling the lunar regolith granular material fluidic characteristics poses special challenges due to complex particle shapes and mixture composition. The lunar regolith is poorly sorted with broad particle size distributions and large fines content. It has significant cohesion, due to interlocking jagged particle shapes. Eulerian granular material flow modeling requires closure formulations for the granular material constitutive models (stress, friction, collisional and kinetic energy dissipation, drag, etc.). While closure models for spherical particles are available from particle kinetic theory, closure models for realistic non-spherical particles must be extracted from unit physics Discrete Element Model (DEM) particle interaction simulations and provided in the form of tabular datasets. The effects of particle irregular shape (non-spherical shape factors, angular particle surface roughness, and interlocking features) are simulated by approximating the particle features in the form of grouped elemental spheres to form composite particles in the DEM simulations. The effects of the wide range of regolith mixture particle sizes and the strong effects of the presence of the small particle sizes results in high cohesion and low porosity of the regolith mixture. The range of particle sizes is simulated by binning the particle sizes into an appropriate finite number of particle-size species and solving the problem as a species mixture. Combining these two modeling approaches enables simulations to capture both, the contributions of the irregular particle shape and the particle size distribution. The integration and maturation of the DEM-based constitutive model database generation process and poly-disperse mixture binning approach into the GGFS simulation framework are proceeding under funding by the NASA Game Changing Development program. The status of current capabilities will be presented in comparisons of crater characteristics resulting for spherical and irregular shape particles, and for mono-, bi-, and tri-disperse mixture simulations of Apollo LM plume-surface interaction. The computational results confirm the significance of including the particle shape and mixture effects. Going forward plans for the full implementation of the general poly-disperse regolith modeling capability and maturation towards NASA project application readiness under the GCD program will be presented.

Peter A. Liever↗
DOE OSTI2024

Design, Fabrication and Testing of Surveillance Test Articles for MSR Materials Degradation Management

This report details the design, fabrication, and testing of surveillance test articles aimed at assessing material damage in reactor-relevant environments for effective degradation management. Two types of surveillance test articles with reduced sizes were developed based on design algorithms and finite element modeling: welded design and interlocking design. A furnace heating setup was adopted to apply multiple thermal cyclic loading profiles on the test articles with a temperature range of 500°C - 700°C, while the strain response was monitored using a digital image correlation technique. The testing results demonstrated the successful capturing of expected strain range for welded design while machining tolerance should be improved to engage strain coupling in the interlocking design. Mid-term (500 hours) and long-term (1500 hours) cyclic tests were conducted on welded test articles. A constant strain range of ~0.6% was observed at the specimen with testing under 500 hours, while a gradual decrease of strain at specimen was observed after 500 hours. Non-destructive evaluation through X-ray computed tomography confirmed the microcracks in the welds at specimen-driver joints after cyclic test that caused the strain change. Creep testing of the specimen after long-term cyclic test revealed a short creep life than expected. A multi-profile cyclic test was also conducted on a test article and demonstrated consistent strain response under different temperature ramp rates. The report also briefly discussed the challenges and future research efforts to advance test article development for material surveillance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Photoresponsive Rotaxanes Switch Lipid Bilayer Neuromorphic Behavior with Light

A rotaxane consisting of a macrocycle ring with two azobenzene units mechanically interlocked onto a bolaamphiphilic axle was incorporated into droplet interface bilayers (DIBs). The azobenzene groups on the ring underwent quasi-reversible, photoisomerization-induced cycling between 1-E and 1-Z configurations when irradiated with 370 and 467 nm light, respectively, enabling programmable access to different history-dependent electrical behaviors from the same membrane. In the 1-E configuration, bilayers exhibited type-IIactive memristance that coincided with increasingly elevated ionic conduction, associated with progressively enhanced bilayer permeability during voltage cycling. In the 1-Z configuration, bilayers displayed type-I, passive memcapacitive behavior, reflecting tighter lipid packing and reduced ionic permeability. Photoswitching also yielded a nonvolatile, photoresponsive memcapacitor that could be modulated repetitively with negligible loss, likely via reversible changes in membrane thickness. Concurrent ohmic leakage currents across the membrane were less than 0.3%. These results agree with previous studies with increasing membrane permeability using photoswitchable rotaxanes and provide new insights into the coupling between volatile and nonvolatile memcapacitance during photoisomerization. More broadly, they demonstrate a new strategy for the manipulation of neuromorphic behaviors in soft materials using light, with implications for brain-inspired computation and sensing.

droplet interface bilayers↗
DOE OSTI2024

Small‐Molecule Mixed Ionic‐Electronic Conductors for Efficient N‐Type Electrochemical Transistors: Structure‐Function Correlations

Abstract The fundamental challenge in electron‐transporting organic mixed ionic‐electronic conductors (OMIECs) is simultaneous optimization of electron and ion transport. Beginning from Y6‐type/U‐shaped non‐fullerene solar cell acceptors, we systematically synthesize and characterize molecular structures that address the aforementioned challenge, progressively introducing increasing numbers of oligoethyleneglycol (OEG; g) sidechains from 1 g to 3 g, affording OMIECs 1gY, 2gY, and 3gY, respectively. The crystal structure of 1gY preserves key structural features of the Y n series: a U‐shaped/planar core, close π–π molecular stacking, and interlocked acceptor groups. Versus inactive Y6 and Y11, all of the new glycolated compounds exhibit mixed ion‐electron transport in both conventional organic electrochemical transistor (cOECT) and vertical OECT (vOECT) architectures. Notably, 3gY with the highest OEG density achieves a high transconductance of 16.5 mS, an on/off current ratio of ~10 6 , and a turn‐on/off response time of 94.7/5.7 ms in vOECTs. Systematic optoelectronic, electrochemical, architectural, and crystallographic analysis explains the superior 3gY‐based OECT performance in terms of denser n gY OEG content, increased crystallite dimensions with decreased long‐range crystalline order, and enhanced film hydrophilicity which facilitates ion transport and efficient redox processes. Finally, we demonstrate an efficient small‐molecule‐based complementary inverter using 3gY vOECTs, showcasing the bioelectronic applicability of these new small‐molecule OMIECs.

Cho, Yongjoon↗
DOE OSTI2024

Small‐Molecule Mixed Ionic‐Electronic Conductors for Efficient N‐Type Electrochemical Transistors: Structure‐Function Correlations

Abstract The fundamental challenge in electron‐transporting organic mixed ionic‐electronic conductors (OMIECs) is simultaneous optimization of electron and ion transport. Beginning from Y6‐type/U‐shaped non‐fullerene solar cell acceptors, we systematically synthesize and characterize molecular structures that address the aforementioned challenge, progressively introducing increasing numbers of oligoethyleneglycol (OEG; g) sidechains from 1 g to 3 g, affording OMIECs 1gY, 2gY, and 3gY, respectively. The crystal structure of 1gY preserves key structural features of the Y n series: a U‐shaped/planar core, close π–π molecular stacking, and interlocked acceptor groups. Versus inactive Y6 and Y11, all of the new glycolated compounds exhibit mixed ion‐electron transport in both conventional organic electrochemical transistor (cOECT) and vertical OECT (vOECT) architectures. Notably, 3gY with the highest OEG density achieves a high transconductance of 16.5 mS, an on/off current ratio of ~10 6 , and a turn‐on/off response time of 94.7/5.7 ms in vOECTs. Systematic optoelectronic, electrochemical, architectural, and crystallographic analysis explains the superior 3gY‐based OECT performance in terms of denser n gY OEG content, increased crystallite dimensions with decreased long‐range crystalline order, and enhanced film hydrophilicity which facilitates ion transport and efficient redox processes. Finally, we demonstrate an efficient small‐molecule‐based complementary inverter using 3gY vOECTs, showcasing the bioelectronic applicability of these new small‐molecule OMIECs.

Cho, Yongjoon↗