Search NASA⌕ Search

SEARCH · Search NASA

Results for “irreversible capacity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Two-level systems and growth-induced metastability in hydrogenated amorphous silicon

Specific heat measurements from 2 to 300 K of hydrogenated amorphous silicon prepared by hot-wire chemical vapor deposition show a large excess specific heat at low temperature, significantly larger than the Debye specific heat calculated from the measured sound velocity. The as-prepared films have a Schottky anomaly that is associated with metastable hydrogen in the amorphous network, as well as large linear and excess cubic term commonly associated with tunneling two-level systems in amorphous solids. Annealing at 200 °C, a temperature that enables hydrogen mobility but not evaporation, irreversibly reduces the heat capacity, eliminating the Schottky anomaly and leaving a reduced linear heat capacity. A non-monotonic dependence on growth temperature and H content is observed in all effects, except for sound velocity, which suggests that the tunneling two-level systems and the Schottky anomaly are associated with atomic hydrogen and require low density regions to form, while sound velocity is associated with the silicon network and increases with increasing growth temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Composition Dependent Electrochemical Properties of Earth-Abundant Ternary Nitride Anodes

Growing energy storage demands on lithium-ion batteries necessitate exploration of new electrochemical materials as next-generation battery electrode materials. In this work, we investigate the previously unexplored electrochemical properties of earth-abundant and tunable Zn 1-x Sn 1+x N 2 (x = -0.4 to x = 0.4) thin films, which show high electrical conductivity and high gravimetric capacity for Li insertion. Enhanced cycling performance is achieved compared to previously published end-members Zn 3 N 2 and Sn 3 N 4 , showing decreased irreversible loss and increased total capacity and cycle stability. The average reversible capacity observed is >1050 mAh/g for all compositions and 1220 mAh/g for Zn-poor (x = 0.2) films. Extremely Zn-rich films (x = -0.4) show improved adhesion; however, Zn-rich films undergo a phase transformation on the first cycle. Zn-poor and stoichiometric films do not exhibit significant phase transformations which often plague nitride materials and show no required overpotential at the 0.5 V plateau. Cation composition x is explored as a mechanism for tuning relevant mechanical and electrochemical properties, such as capacity, overpotential, phase transformation, electrical conductivity, and adhesion. The lithiation/delithiation experiments confirm the reversible electrochemical reactions. Without any binding additives, the as-deposited electrodes delaminate resulting in fast capacity degradation. We demonstrate the mechanical nature of this degradation through decreased electrode thinning, resulting in cells with improved cycling stability due to increased mechanical stability. Combining composition and electrochemical analysis, this work demonstrates for the first time composition dependent electrochemical properties for the ternary Zn 1-x Sn 1+x N 2 and proposes earth-abundant ternary nitride anodes for increased reversible capacity and cycling stability.

25 ENERGY STORAGE↗
DOE OSTI2020

Structural Degradation of High Voltage Lithium Nickel Manganese Cobalt Oxide (NMC) Cathodes in Solid-State Batteries and Implications for Next Generation Energy Storage

In this study, we report the stability of the layered high voltage cathode NMC622 with respect to a standard liquid electrolyte and in an all solid-state configuration. NMC622 cathodes with a (104) orientation were found to suffer from degradation at high voltage (4.5 V vs Li/Li + ) due to electrolyte-promoted degradation of the layered structure in a carbonate electrolyte. The lithium phosphorus oxynitride (LiPON) electrolyte was able to suppress the extent of this decomposition in solid-state cells but not totally prevent it from occurring. In the solid-state cells the capacity decreased from 203 to 93 mAh/g in the first cycle and from 93 to 79 mAh/g over the subsequent 99 cycles, whereas, after 20 cycles, the liquid cell charge capacity was dominated by the irreversible electrolyte degradation. Furthermore, the interfacial resistances of the solid-state cells were stable with cycling, suggesting minimal degradation of the NMC622/LiPON interface and incumbent losses due to structural evolution associated with cathode orientation. This data indicates that accessing stable high voltage capacity in NMCs will not be enabled by simply stabilizing the cathode–electrolyte interface. Optimizing cathode crystallographic orientation may be the key to accessing this high voltage regime.

25 ENERGY STORAGE↗
DOE OSTI2021

Modulating the Surface Ligand Orientation for Stabilized Anionic Redox in Li‐Rich Oxide Cathodes

Abstract Anionic redox chemistry is emerging as a key concept in the development of high‐energy lithium‐ion batteries, as it enables a nearly doubled charge storage capacity, aiding the development of high‐capacity batteries. However, the anionic reactivity is frequently irreversible from charge to discharge, leading to rapid decay of the capacity and voltage of batteries over long‐term cycling. Although the possibility of controlling the anionic redox reactions by tuning the geometric and electronic structures has recently been proposed, the implementation of this strategy is still a critical challenge. Herein, a strategy is proposed to improve the anionic redox reversibility of a model anionic redox active cathode material, Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 , by tuning the surface ligand geometry via the growth of a lattice‐compatible spinel LiCoO 2 coating layer on the particle surface. Detailed local structure and first principles investigations reveal that the shape and orientation of the octahedral layer in the host lattice are modified. Accordingly, a two‐band oxygen redox behavior is triggered in the ligand‐orientation‐regulated Li‐rich cathode, leading to enhanced reversibility, and thus, remarkably improved capacity and voltage retention over cycling. This study highlights the importance of controllable ligand orientation, carving a new path for the development and design of Li‐rich cathodes in the future.

Liu, Yanchen↗
DOE OSTI2026

Engineering Na‐Rich P2‐Type Layered Oxides Through Li/Ti Dual Doping for Oxygen Redox Activation and Superior Structural Stability

Sodium layered oxides Na x MO 2 (x ≤ 1 and M = transition metal ions) have gained significant interest as sodium-ion battery (NIB) cathodes owing to their high operating voltages and potential for higher energy density compared with polyanion and Prussian blue–type cathodes. However, their practical applications are often hindered by the irreversible structural transitions leading to capacity fading during cycling. The nature and substitution of transition metal ions define the material properties and electrochemical performance. In this study, through comprehensive electrochemical characterization combined with multi-scale structural and spectroscopical analyses, we demonstrate the synergistic impacts of Lithium and Titanium doping, which not only increases overall capacity by boosting cation and anion cooperative redox contributions but also improves the rate capability and cycling stability. Specifically, Li + doping enhances the available sodium inventory for extraction, while Ti 4+ disrupts Na + /vacancy ordering at lower voltages (< 4 V) and mitigates the detrimental P2→OP4/O2 phase transition during cycling. The combined effect of Lithium and Titanium doping promotes more charge localization on Oxygen, which activates reversible lattice oxygen redox reactions at elevated voltages, contributing additional capacity beyond conventional cationic redox. This work provides crucial insights into the design of high-performance, high-capacity P2-type layered cathode materials for sodium-ion batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Regulating the Electron Distribution of Metal-Oxygen for Enhanced Oxygen Stability in Li-rich Layered Cathodes

Li-rich Mn-based layered oxides (LLO) hold great promise as cathode materials for lithium-ion batteries (LIBs) due to their unique oxygen redox (OR) chemistry, which enables additional capacity. However, the LLOs face challenges related to the instability of their OR process due to the weak transition metal (TM)-oxygen bond, leading to oxygen loss and irreversible phase transition that results in severe capacity and voltage decay. Herein, a synergistic electronic regulation strategy of surface and interior structures to enhance oxygen stability is proposed. In the interior of the materials, the local electrons around TM and O atoms may be delocalized by surrounding Mo atoms, facilitating the formation of stronger TM—O bonds at high voltages. Besides, on the surface, the highly reactive O atoms with lone pairs of electrons are passivated by additional TM atoms, which provides a more stable TM—O framework. Hence, this strategy stabilizes the oxygen and hinders TM migration, which enhances the reversibility in structural evolution, leading to increased capacity and voltage retention. This work presents an efficient approach to enhance the performance of LLOs through surface-to-interior electronic structure modulation, while also contributing to a deeper understanding of their redox reaction.

25 ENERGY STORAGE↗
DOE OSTI2026

Restoring Escaped Zincate in Rechargeable Alkaline Zinc Batteries with a Seed-in-Nanoshell Design

Rechargeable alkaline zinc batteries are promising candidates for safe and low-cost energy storage, but suffer from ZnO dissolution that causes irreversible active material loss and rapid capacity decay. Here, we report a seed-in-nanoshell ZnO anode architecture that mitigates dissolution by combining physical confinement with electrochemical restoration of dissolved zincate species. ZnO particles are encapsulated within an ion-sieving carbon nanoshell that restricts zincate diffusion, maintains electrical conductivity, and stabilizes repeated solid–solution–solid transformations. Silver (Ag) nanoparticles incorporated into the nanoshell act as zincophilic nucleation seeds, lowering the Zn deposition barrier and directing the redeposition of dissolved zincate back to metallic Zn during charging. This confinement-enabled restoration mechanism converts zincate dissolution from an irreversible loss pathway into a recoverable process, enabling improved performance under harsh test conditions. The anode also delivers 227.9 mAh g −1 at −40 °C. Finally, a scalable tens-of-gram synthesis of ZnO@Ag is demonstrated, underscoring the practical potential of this strategy for advanced aqueous zinc batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Development of High Capacity Energy Storage Materials

Hydrogen fuel cells have the potential to offer energy and power density advantages over lithium ion batteries in automotive and portable power applications when paired with an appropriate hydrogen storage system. Development of the ideal hydrogen storage material has been immensely sought after but plagued by limitations present in each type of material. These limitations typically include nonidealistic operational temperatures, low capacities, excessive costs, lack of reversibility, or evolution of impurities which irreversibly damage fuel cell performance. Many complex metal hydrides possess suitable hydrogen capacities but unfortunately suffer from impurity release. In order to address this problem, our team has explored in-situ catalyst doping of alkali metal amides to demonstrate methodologies to reduce ammonia release. The incorporation of iridium metal in lithium amide significantly reduces the ammonia release and decomposes the ammonia to provide additional hydrogen. Furthermore, we demonstrate, for the first time, high resistance of low temperature fuel cells to ammonia in comparison with typical proton exchange membrane fuel cells. The utilization of these two approaches in tandem provides a novel pathway for the development and implementation of high capacity energy storage materials for fuel cell applications.

25 ENERGY STORAGE↗
DOE OSTI2024

Unleashing the Potential of Fast Charging Batteries: Leveraging Anion Redox Chemistry in Ni- and Co-Free Cathodes

Designing Li-ion battery cathodes free from critical raw materials such as Co and Ni has a huge technological and societal impact. Though anion redox-based Li-rich oxide cathodes allow designing Co and Ni free cathode compositions, the Li-rich oxides witnessed voltage fade, voltage hysteresis, and irreversible oxygen release despite their high capacity. Conversely, anion redox through highly covalent chalcogenides (S/Se) is emerging due to the improved covalency between metal d and ligand p bands. Here, we investigate the tuning of multi-chalcogen (S/Se) p-band and redox-active metal d-band in a model Li-rich chalcogen composition Li 1.13 Ti 0.57 Fe 0.3 S 2-y Se y (y = 0 - 1) through in-depth electrochemical, X-ray spectroscopy, and DFT-based electronic structure investigations. Introducing the appropriate amount of Se p band character in anion redox sulfides increases interlayer distance and metal - ligand covalency without modifying the original crystal structure, promoting significant electrochemical reversibility through mixed anionic (Se 2- /Se n- , S 2- /S n- , wherein n<2) and cationic (Fe 2+ /Fe 3+ ) redox reactions. Here we show the detailed Fe, S, and Se redox contributions during Li insertion/extraction through X-ray Absorption (XAS) and Hard X-ray Photoemission Spectroscopy (HAXPES) measurements. The orbital tuning approach improves rate capability for more than 10 C charge-discharge rate, exhibiting more than 50% of its original capacity obtained at C/20 rate. The buffer cation in the lattice (Ti 4+ ) remains electrochemically inactive even after significant Se p-band introduction in the sulfide framework. Overall, this work takes advantage of multi-anion redox chemistry to uncover practically demanding fast charging-discharging characteristics in intercalation cathodes. The obtained knowledge of this design can be extended to other oxide and chalcogen cathodes for high performance Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Battery data integrity and usability: Navigating datasets and equipment limitations for efficient and accurate research into battery aging

A tremendous commitment of resources is needed to acquire, understand and apply battery data in terms of performance and aging behavior. There are many state of performance (SOP) and state of health (SOH) metrics that are useful to guide alignment of batteries to end-use, yet how these metrics are measured or extracted can make the difference between usable, valuable datasets versus data that lacks the necessary integrity to meet baseline confidence levels for SOP/SOH quantification. This work will speak to 1) types of data that support SOP and SOH evaluations on mechanistic terms, 2) measurement conditions needed to assure high data integrity, 3) equipment limitations that can compromise data high fidelity, and 4) the impact of cell polarization on data quality. A common goal in battery research and field use is to work from a data platform that supports economical paths of data capture while minimizing down-time for battery diagnostics. An ideal situation would be to utilize data obtained during normal daily use (“pulses or cycles of convenience”) without stopping the daily duty cycles to perform dedicated SOP/SOH diagnostic routines. However, difficulties arise in trying to make use of daily duty cycle data (denoted as cycle-by-cycle, CBC) that underscores the need for standardization of conditions: temperature and duty cycles can vary over the course of a day and throughout a week, month and year; polarization can develop within an immediate cycle and throughout successive cycles as a hysteresis. If CBC data is envisioned as a data source to determine performance and aging trends, it should be recognized that polarization is a frequent consequence of CBC and thus makes it difficult to separate reversible and irreversible components to metrics such as capacity loss and resistance increase over aging. Since CBC conditions can have a major impact on data usability, we will devote part of this paper to CBC data conditioning and management. Differential analyses will also be discussed as a means to detect changing trends in data quality. Our target cell chemistries will be lithium-ion types NMC/graphite and LMO/LTO.

25 ENERGY STORAGE↗
DOE OSTI2025

Stable Cycling of Sodium All‐Solid‐State Batteries with High‐Capacity Cathode Presodiation

Sodium all-solid-state batteries (NaSSBs) with an alloy-type anode (e.g., Sn and Sb) offer superior capacity and energy density compared to hard carbon anode. However, the irreversible loss of Na + at the alloy anode during the initial cycle results in diminished capacity and stability, impairing full-cell performance. Here, this study presents an easy-to-implement cathode presodiation strategy by employing a Na-rich material to address these challenges. Leveraging the high theoretical capacity and suitable voltage window, Na 2 S is chosen as the Na donor, which is activated by creating a mixed electron-ion conducting network, delivering a high capacity of 511.7 mAh g −1 . By adding a small amount (i.e., 3 wt.%) of Na 2 S to the cathode composite, a NaCrO 2 || Sn full cell demonstrated capacity improvement from 90.8 to 118.2 mAh g −1 (based on cathode mass). The capacity-balanced full cell can thus cycle to more than 300 times with >90% capacity retention. This work provides a practical solution to enhance the full-cell performance and advance the transformation from half-cell to full-cell applications of NaSSBs.

25 - ENERGY STORAGE↗
DOE OSTI2022

Theoretical and Experimental Investigation of Functionalized Cyanopyridines Yield an Anolyte with an Extremely Low Reduction Potential for Nonaqueous Redox Flow Batteries

Abstract Cyanopyridines and cyanophenylpyridines were investigated as anolytes for nonaqueous redox flow batteries (RFBs). The three isomers of cyanopyridine are reduced at potentials of −2.2 V or lower vs. ferrocene +/0 (Fc +/0 ), but the 3‐CNPy⋅ − radical anion forms a sigma‐dimer that is re‐oxidized at E ≈−1.1 V, which would lead to poor voltaic efficiency in a RFB. Bulk electrochemical charge‐discharge cycling of the cyanopyridines in acetonitrile and 0.50 M [NBu 4 ][PF 6 ] shows that 2‐CNPy and 4‐CNPy lose capacity quickly under these conditions, due to irreversible chemical reaction/decomposition of the radical anions. Density‐functional theory (DFT) calculations indicated that adding a phenyl group to the cyanopyridines would, for some isomers, limit dimerization and improve the stability of the radical anions, while shifting their E 1/2 only about +0.10 V relative to the parent cyanopyridines. Among the cyanophenylpyridines, 3‐CN‐6‐PhPy and 3‐CN‐4‐PhPy are the most promising as anolytes. They exhibit reversible reductions at E 1/2 =−2.19 and −2.22 V vs. ferrocene +/0 , respectively, and retain about half of their capacity after 30 bulk charge‐discharge cycles. An improved version of 3‐CN‐6‐PhPy with three methyl groups (3‐cyano‐4‐methyl‐6‐(3,5‐dimethylphenyl)pyridine) has an extremely low reduction potential of −2.50 V vs. Fc +/0 (the lowest reported for a nonaqueous RFB anolyte) and loses only 0.21 % of capacity per cycle during charge‐discharge cycling in acetonitrile.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Toward the Understanding of the Reaction Mechanism of Zn/MnO2 Batteries Using Non-alkaline Aqueous Electrolytes

Zn/MnO 2 systems using non-alkaline aqueous electrolytes have attracted tremendous interest as rechargeable aqueous Zn ion batteries due to their safety and high specific capacities. Despite their promising electrochemical performance, however, their reaction mechanism has remained elusive. Here in this paper, we examined the structural evolution of cryptomelane α-MnO 2 cathode by ex situ transmission electron microscopy after electrochemical testing using two different non-alkaline aqueous Zn electrolytes with acetate and triflate salts of different pH values. We have discovered that the systems tested in both electrolytes exhibit a dissolution–deposition reaction mechanism through dissolution–deposition of Mn 2+ ions from/on the cathodes with a display of similar discharge/charge product formation. We have also found that the cell tested using the acetate electrolyte shows evidence of structural irreversibility that might contribute to its rapid capacity degradation. This finding offers an important insight into optimizing the cathode design for enhanced electrochemical function of aqueous Zn/MnO 2 batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Quantification of heterogeneous, irreversible lithium plating in extreme fast charging of lithium-ion batteries

Realization of extreme fast charging (XFC, ≤15 minutes) of lithium-ion batteries is imperative for the widespread adoption of electric vehicles. However, dramatic capacity fading is associated with XFC, limiting its implementation. To quantitatively elucidate the effects of irreversible lithium plating and other degradation mechanisms on the cell capacity, it is important to understand the links between lithium plating and cell degradation at both the local and global (over the full cell) scales. Here, we study the nature of local lithium plating after hundreds of XFC cycles (charging C-rates ranging from 4C to 9C) in industrially-relevant pouch cells using spatially resolved X-ray diffraction. Our results reveal a spatial correlation at the mm scale between irreversible lithium plating on the anode, inactive lithiated graphite phases, and local state-of-charge of the cathode. In regions of plated lithium, additional lithium is locally and irreversibly trapped as lithiated graphite, contributing to the loss of lithium inventory (LLI) and to a local loss of active anode material. The total LLI in the cell from irreversibly plated lithium is linearly correlated to the capacity loss in the batteries after XFC cycling, with a non-zero offset originating from other parasitic side reactions. Finally, at the global (cell) scale, LLI drives the capacity fade, rather than electrode degradation. We anticipate that the understanding of lithium plating and other degradation mechanisms during XFC gained in this work will help lead to new approaches towards designing high-rate batteries in which irreversible lithium plating is minimized.

25 ENERGY STORAGE↗
DOE OSTI2022

Entropy and crystal-facet modulation of P2-type layered cathodes for long-lasting sodium-based batteries

Abstract P2-type sodium manganese-rich layered oxides are promising cathode candidates for sodium-based batteries because of their appealing cost-effective and capacity features. However, the structural distortion and cationic rearrangement induced by irreversible phase transition and anionic redox reaction at high cell voltage (i.e., >4.0 V) cause sluggish Na-ion kinetics and severe capacity decay. To circumvent these issues, here, we report a strategy to develop P2-type layered cathodes via configurational entropy and ion-diffusion structural tuning. In situ synchrotron X-ray diffraction combined with electrochemical kinetic tests and microstructural characterizations reveal that the entropy-tuned Na 0.62 Mn 0.67 Ni 0.23 Cu 0.05 Mg 0.07 Ti 0.01 O 2 (CuMgTi-571) cathode possesses more {010} active facet, improved structural and thermal stability and faster anionic redox kinetics compared to Na 0.62 Mn 0.67 Ni 0.37 O 2 . When tested in combination with a Na metal anode and a non-aqueous NaClO 4 -based electrolyte solution in coin cell configuration, the CuMgTi-571-based positive electrode enables an 87% capacity retention after 500 cycles at 120 mA g −1 and about 75% capacity retention after 2000 cycles at 1.2 A g −1 .

25 ENERGY STORAGE↗
DOE OSTI2022

Elastic Lattice Enabling Reversible Tetrahedral Li Storage Sites in a High-Capacity Manganese Oxide Cathode

The key to breaking through the capacity limitation imposed by intercalation chemistry lies in the ability to harness more active sites that can reversibly accommodate more ions (e.g., Li + ) and electrons within a finite space. However, excessive Li-ion insertion into the Li layer of layered cathodes results in fast performance decay due to the huge lattice change and irreversible phase transformation. Here, in this study, an ultrahigh reversible capacity is demonstrated by a layered oxide cathode purely based on manganese. Through a wealth of characterizations, it is clarified that the presence of low-content Li 2 MnO 3 domains not only reduces the amount of irreversible O loss; but also regulates Mn migration in LiMnO 2 domains, enabling elastic lattice with high reversibility for tetrahedral sites Li-ion storage in Li layers. This work utilizes bulk cation disorder to create stable Li-ion-storage tetrahedral sites and an elastic lattice for layered materials, with a reversible capacity of 600 mA h g –1 , demonstrated in th range 0.6–4.9 V versus Li/Li + at 10 mA g –1 . Admittedly, discharging to 0.6 V might be too low for practical use, but this exploration is still of great importance as it conceptually demonstrates the limit of Li-ions insertion into layered oxide materials.

25 ENERGY STORAGE↗
DOE OSTI2021

Stabilizing Anionic Redox Chemistry in a Mn-Based Layered Oxide Cathode Constructed by Li-Deficient Pristine State

Li-rich cathode materials are of significant interest for coupling anionic redox with cationic redox chemistry to achieve high-energy-density batteries. However, lattice oxygen loss and derived structure distortion would induce serious capacity loss and voltage decay, further hindering its practical application. Herein, a novel Li-rich cathode material, O3-type Li 0.6 [Li 0.2 Mn 0.8 ]O 2 , is developed with the pristine state displaying both a Li excess in the transition metal layer and a deficiency in the alkali metal layer. Benefiting from stable structure evolution and Li migration processes, not only can high reversible capacity (≈329 mAh g -1 ) be harvested but also irreversible/reversible anionic/cationic redox reactions are comprehensively assigned via the combination of in/ex situ spectroscopies. Furthermore, irreversible lattice oxygen loss and structure distortion are effectively restrained, resulting in long-term cycle stability (capacity drop of 0.045% per cycle, 500 cycles). Altogether, tuning the Li state in the alkali metal layer presents a promising way for modification of high-capacity Li-rich cathode candidates.

anionic redox reactions↗
DOE OSTI2025

Constraining Interlayer Slipping in P2-Type Layered Oxides with Oxygen Redox by Constructing Strong Covalent Bonds

Lattice oxygen redox (LOR) in P2-type layered oxides is an effective strategy to break through the limit of energy density of conventional cathodes due to its high redox potential (>4 V vs. Na + /Na) as well as extra capacity. Nevertheless, LOR induced local structure distortion and irreversible phase transitions cause serious electrochemical performance degradation, hindering the practical applications. In this work, we propose that the generation of the OP4 phase can be replaced with the Z phase by introducing Sb element with higher ionic potential and strong covalent bonds within the TMO 6 octahedron. Z phase transition is realized by constraining interlayer slipping between adjacent TM layers compared to OP4, which reduces the strain in the layered structure, lowers the Na+ diffusion energy barrier and creates more efficient Na+ diffusion channels. Consequently, Sb-substituted oxides demonstrates excellent kinetics, rate capability (79 mAh g -1 at 1 A g -1 ) in half cell and a high energy density of 487 Wh kg -1 (on cathode) in full cell.

25 ENERGY STORAGE↗