Search NASA⌕ Search

SEARCH · Search NASA

Results for “laminate modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Development of a Higher Order Laminate Theory for Modeling Composites with Induced Strain Actuators

A refined higher order plate theory is developed to investigate the actuation mechanism of piezoelectric materials surface bonded or embedded in composite laminates. The current analysis uses a displacement field which accurately accounts for transverse shear stresses. Some higher order terms are identified by using the conditions that shear stresses vanish at all free surfaces. Therefore, all boundary conditions for displacements and stresses are satisfied in the present theory. The analysis is implemented using the finite element method which provides a convenient means to construct a numerical solution due to the discrete nature of the actuators. The higher order theory is computationally less expensive than a full three dimensional analysis. The theory is also shown to agree well with published experimental results. Numerical examples are presented for composite plates with thicknesses ranging from thin to very thick.

Chattopadhyay, Aditi↗
NASA NTRS1990

Nondimensional impact models for composite laminates

The equations governing the problem of low-velocity impact of a simply supported rectangular laminated plate are nondimensionalized such that the problem is defined in terms of five dimensionless parameters. A parametric study using the Graeco-Latin Factorial Plan is performed. Semi-empirical formulas for maximum impact force, impact duration, and maximum back surface strains are obtained. It is found that some of the simple impact models provide the bounds for the case of impact on a finite extent plate.

Sankar, B. V.↗
NASA NTRS2015

Application of the Refined Zigzag Theory to the Modeling of Delaminations in Laminated Composites

The Refined Zigzag Theory is applied to the modeling of delaminations in laminated composites. The commonly used cohesive zone approach is adapted for use within a continuum mechanics model, and then used to predict the onset and propagation of delamination in five cross-ply composite beams. The resin-rich area between individual composite plies is modeled explicitly using thin, discrete layers with isotropic material properties. A damage model is applied to these resin-rich layers to enable tracking of delamination propagation. The displacement jump across the damaged interfacial resin layer is captured using the zigzag function of the Refined Zigzag Theory. The overall model predicts the initiation of delamination to within 8% compared to experimental results and the load drop after propagation is represented accurately.

Groh, Rainer M. J.↗
NASA NTRS1991

A continuum model for damage evolution in laminated composites

The accumulation of matrix cracking is examined using continuum damage mechanics lamination theory. A phenomenologically based damage evolutionary relationship is proposed for matrix cracking in continuous fiber reinforced laminated composites. The use of material dependent properties and damage dependent laminate averaged ply stresses in this evolutionary relationship permits its application independently of the laminate stacking sequence. Several load histories are applied to crossply laminates using this model, and the results are compared to published experimental data. The stress redistribution among the plies during the accumulation of matrix damage is also examined. It is concluded that characteristics of the stress redistribution process could assist in the analysis of the progressive failure process in laminated composites.

Lo, D. C.↗
NASA NTRS2006

A Micromechanics-Based Damage Model for the Strength Prediction of Composite Laminates

A new damage model based on a micromechanical analysis of cracked [+/-0deg/90deg(sub n)]s laminates subjected to multiaxial loads is proposed. The model predicts the onset and accumulation of transverse matrix cracks in uniformly stressed laminates, the effect of matrix cracks on the stiffness of the laminate, as well as the ultimate failure of the laminate. The model also accounts for the effect of the ply thickness on the ply strength. Predictions relating the elastic properties of several laminates and multiaxial loads are presented.

Camanho, Pedro P.↗
NASA NTRS2008

Modeling the Non-Linear Response of Fiber-Reinforced Laminates Using a Combined Damage/Plasticity Model

The present work is concerned with modeling the non-linear response of fiber reinforced polymer laminates. Recent experimental data suggests that the non-linearity is not only caused by matrix cracking but also by matrix plasticity due to shear stresses. To capture the effects of those two mechanisms, a model combining a plasticity formulation with continuum damage has been developed to simulate the non-linear response of laminates under plane stress states. The model is used to compare the predicted behavior of various laminate lay-ups to experimental data from the literature by looking at the degradation of axial modulus and Poisson s ratio of the laminates. The influence of residual curing stresses and in-situ effect on the predicted response is also investigated. It is shown that predictions of the combined damage/plasticity model, in general, correlate well with the experimental data. The test data shows that there are two different mechanisms that can have opposite effects on the degradation of the laminate Poisson s ratio which is captured correctly by the damage/plasticity model. Residual curing stresses are found to have a minor influence on the predicted response for the cases considered here. Some open questions remain regarding the prediction of damage onset.

Schuecker, Clara↗
NASA NTRS1989

Mechanics of unsymmetric laminates

Theoretical models describing the mechanical behavior of fiber-reinforced composite laminates are developed analytically and demonstrated. The curing of composite structures and the out-of-plane shapes of unsymmetric laminates are discussed and illustrated with photographs; the derivation of the governing equations is outlined; numerical results for typical laminates are presented in graphs; and particular attention is given to stability considerations and the effects of material properties, laminate thickness, aspect ratio, and stacking sequence.

Hyer, M. W.↗
NASA NTRS2000

A Shell/3D Modeling Technique for the Analysis of Delaminated Composite Laminates

A shell/3D modeling technique was developed for which a local solid finite element model is used only in the immediate vicinity of the delamination front. The goal was to combine the accuracy of the full three-dimensional solution with the computational efficiency of a shell finite element model. Multi-point constraints provided a kinematically compatible interface between the local 3D model and the global structural model which has been meshed with shell finite elements. Double Cantilever Beam, End Notched Flexure, and Single Leg Bending specimens were analyzed first using full 3D finite element models to obtain reference solutions. Mixed mode strain energy release rate distributions were computed using the virtual crack closure technique. The analyses were repeated using the shell/3D technique to study the feasibility for pure mode I, mode II and mixed mode I/II cases. Specimens with a unidirectional layup and with a multidirectional layup were simulated. For a local 3D model, extending to a minimum of about three specimen thicknesses on either side of the delamination front, the results were in good agreement with mixed mode strain energy release rates obtained from computations where the entire specimen had been modeled with solid elements. For large built-up composite structures the shell/3D modeling technique offers a great potential for reducing the model size, since only a relatively small section in the vicinity of the delamination front needs to be modeled with solid elements.

Krueger, Ronald↗
NASA NTRS2001

A Shell/3D Modeling Technique for the Analyses of Delaminated Composite Laminates

A shell/3D modeling technique was developed for which a local three-dimensional solid finite element model is used only in the immediate vicinity of the delamination front. The goal was to combine the accuracy of the full three-dimensional solution with the computational efficiency of a plate or shell finite element model. Multi-point constraints provided a kinematically compatible interface between the local three-dimensional model and the global structural model which has been meshed with plate or shell finite elements. Double Cantilever Beam (DCB), End Notched Flexure (ENF), and Single Leg Bending (SLB) specimens were modeled using the shell/3D technique to study the feasibility for pure mode I (DCB), mode II (ENF) and mixed mode I/II (SLB) cases. Mixed mode strain energy release rate distributions were computed across the width of the specimens using the virtual crack closure technique. Specimens with a unidirectional layup and with a multidirectional layup where the delamination is located between two non-zero degree plies were simulated. For a local three-dimensional model, extending to a minimum of about three specimen thicknesses on either side of the delamination front, the results were in good agreement with mixed mode strain energy release rates obtained from computations where the entire specimen had been modeled with solid elements. For large built-up composite structures modeled with plate elements, the shell/3D modeling technique offers a great potential for reducing the model size, since only a relatively small section in the vicinity of the delamination front needs to be modeled with solid elements.

Krueger, Ronald↗
NASA NTRS1988

A model for predicting damage dependent damping in laminated composites

A constitutive model has been developed for predicting the dynamic properties of composite beams which accounts for the influence of microstructural damage. The model assumes the damage state to be fixed. The model can account for both the damping increase and stiffness loss due to microstructural damage. Damage dependent material constants obtained from a baseline data set can be used to predict damping changes for several composite layups. The validity of the model has been verified by comparing the experimental results to model predictions for crossply laminates with a variety of stacking sequences.

Kalyanasundaram, S.↗
NASA NTRS1993

Theory Of Damping In Composite Laminates

Integrated mathematical model predicts vibration-damping properties of laminated fiber/matrix composite material from micromechanical level to laminate level. Model accounts simultaneously for wider, more realistic variety of laminate configurations and physical phenomena, including asymmetrically oriented plies, anisotropic fiber damping properties, hygral and thermal effects, and coupling among hygral, thermal, and mechanical effects.

Saravanos, D. A.↗
NASA NTRS2013

Cohesive Modeling of Transverse Cracking in Laminates with a Single Layer of Elements per Ply

This study aims to bridge the gap between classical understanding of transverse cracking in cross-ply laminates and recent computational methods for the modeling of progressive laminate failure. Specifically, the study investigates under what conditions a finite element model with cohesive X-FEM cracks can reproduce the in situ effect for the ply strength. It is shown that it is possible to do so with a single element across the thickness of the ply, provided that the interface stiffness is properly selected. The optimal value for this interface stiffness is derived with an analytical shear lag model. It is also shown that, when the appropriate statistical variation of properties has been applied, models with a single element through the thickness of a ply can predict the density of transverse matrix cracks

VanDerMeer, Frans P.↗
NASA NTRS1989

Predictions of Poisson's ratio in cross-ply laminates containing matrix cracks and delaminations

A damage-dependent constitutive model for laminated composites has been developed for the combined damage modes of matrix cracks and delaminations. The model is based on the concept of continuum damage mechanics and uses second-order tensor valued internal state variables to represent each mode of damage. The internal state variables are defined as the local volume average of the relative crack face displacements. Since the local volume for delaminations is specified at the laminate level, the constitutive model takes the form of laminate analysis equations modified by the internal state variables. Model implementation is demonstrated for the laminate engineering modulus E(x) and Poisson's ratio nu(xy) of quasi-isotropic and cross-ply laminates. The model predictions are in close agreement to experimental results obtained for graphite/epoxy laminates.

Harris, Charles E.↗
NASA NTRS1975

Fatigue of notched fiber composite laminates. Part 1: Analytical model

A description is given of a semi-empirical, deterministic analysis for prediction and correlation of fatigue crack growth, residual strength, and fatigue lifetime for fiber composite laminates containing notches (holes). The failure model used for the analysis is based upon composite heterogeneous behavior and experimentally observed failure modes under both static and fatigue loading. The analysis is consistent with the wearout philosophy. Axial cracking and transverse cracking failure modes are treated together in the analysis. Cracking off-axis is handled by making a modification to the axial cracking analysis. The analysis predicts notched laminate failure from unidirectional material fatique properties using constant strain laminate analysis techniques. For multidirectional laminates, it is necessary to know lamina fatique behavior under axial normal stress, transverse normal stress and axial shear stress. Examples of the analysis method are given.

Mclaughlin, P. V., Jr.↗
NASA NTRS1993

Response of automated tow placed laminates to stress concentrations

In this study, the response of laminates with stress concentrations is explored. Automated Tow Placed (ATP, also known as Fiber Placement) laminates are compared to conventional tape layup manufacturing. Previous tensile fracture tests on fiber placed laminates show an improvement in tensile fracture of large notches over 20 percent compared to tape layup laminates. A hierarchial modeling scheme is presented. In this scheme, a global model is developed for laminates with notches. A local model is developed to study the influence of inhomogeneities at the notch tip, which are a consequence of the fiber placement manufacturing technique. In addition, a stacked membrane model was developed to study delaminations and splitting on a ply-by-ply basis. The results indicate that some benefit with respect to tensile fracture (up to 11 percent) can be gained from inhomogeneity alone, but that the most improvement may be obtained with splitting and delaminations which are more severe in the case of fiber placement compared to tape layup. Improvements up to 36 percent were found from the model for fiber placed laminates with damage at the notch tip compared to conventional tape layup.

Cairns, Douglas S.↗
NASA NTRS1987

A finite element model for sound transmission through laminated composite plates

The finite element method is used to model the noise transmission through unstiffened and stiffened laminated composite panels of finite size into a closed cavity. Plate and acoustic finite elements are coupled and the frequencies of the coupled modes are determined. The model is then used to calculate the noise reduction of the panel. Results are compared to experimental values obtained at the NASA Langley Research Center. The purpose of this paper is to demonstrate the use of finite elements to model, for noise transmission calculations, complex structures, such as a stiffened composite panel or a composite panel with windows.

Ramakrishnan, J. V.↗
NASA NTRS2002

Nodal Constraint, Shear Deformation and Continuity Effects Related to the Modeling of Debonding of Laminates, Using Plate Elements

The effects of several critical assumptions and parameters on the computation of strain energy release rates for delamination and debond configurations modeled with plate elements have been quantified. The method of calculation is based on the virtual crack closure technique (VCCT), and models of the upper and lower surface of the delamination or debond that use two-dimensional (2D) plate elements rather than three-dimensional (3D) solid elements. The major advantages of the plate element modeling technique are a smaller model size and simpler configurational modeling. Specific issues that are discussed include: constraint of translational degrees of freedom, rotational degrees of freedom or both in the neighborhood of the debond front, shear deformation assumptions; and continuity of material properties and section stiffness in the vicinity of the debond front. Where appropriate, the plate element analyses are compared with corresponding two-dimensional plane strain analyses.

Glaessgen, E. H.↗