Rapid laser reactive sintering of BaCe0.7Zr0.1Y0.1Yb0.1O3-δ electrolyte for protonic ceramic fuel cells
Not Available
Mu, Shenglong↗
SEARCH · Search NASA
Results for “laser sintering”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Rapid Laser Reactive Sintering for Sustainable and Clean Preparation of Protonic Ceramics
Not Available
08 HYDROGEN↗
Laser-based three-dimensional manufacturing technologies for rechargeable batteries
Laser three-dimensional (3D) manufacturing technologies have gained substantial attention to fabricate 3D structured electrochemical rechargeable batteries. Laser 3D manufacturing techniques offer excellent 3D microstructure controllability, good design flexibility, process simplicity, and high energy and cost efficiencies, which are beneficial for rechargeable battery cell manufacturing. In this review, notable progress in development of the rechargeable battery cells via laser 3D manufacturing techniques is introduced and discussed. The basic concepts and remarkable achievements of four representative laser 3D manufacturing techniques such as selective laser sintering (or melting) techniques, direct laser writing for graphene-based electrodes, laser-induced forward transfer technique and laser ablation subtractive manufacturing are highlighted. Finally, major challenges and prospects of the laser 3D manufacturing technologies for battery cell manufacturing will be provided.
25 ENERGY STORAGE↗
Keyhole-mode Microscopy Dataset for Laser Powder-bed Fusion Modeling
Laser powder-bed fusion (LPBF) is an additive manufacturing (AM) technology that uses high-power sintering lasers to precisely construct metal designs. Material is accumulated by selectively sintering regions of a metal powder layer to a growing structure underneath forming a 3D geometry. Certain conditions make fusion in this process to operate in "keyhole-mode," characterized by targeted materials evaporating as plasma. While keyhole-mode operations can produce deeper molten pools than that observed in "conduction-mode", this mode of operation is often undesirable, as its molten regions can collapse on themselves, encapsulating metal vapors and forming cavities. The formation of such cavities negatively affects strength and consistency of the fused materials. To identify and avoid these detrimental effects of keyhole-mode operation, considerable data collection and analysis regarding this mode of operation is needed. Therefore, under the support of the "Open Data Initiative," Lawrence Livermore National Lab is releasing a dataset for analysis of this keyhole effect, and the conditions which transition operation from conduction-mode to keyhole-mode melting. This dataset consists of 600+ micrographs from laser powder-bed single track runs, with differing cross-section angles and input parameters, operating under both normal and keyhole mode operations. This journal documents the collection, organization, and usage of this dataset.
36 MATERIALS SCIENCE↗
Predicting Selective Laser Printing Print Quality of Polymer Powders through Melt Flow Index
Selective Laser Sintering (SLS) uses a precisely controlled laser to fuse polymer powder to build complex 3D shapes. While SLS covers a wide application space, the processing knowledge of polymer powder is limited, restricting the number of commercial powders available. This study serves to expand the processing knowledge of polypropylene and polyethylene in parallel with a “mature” SLS feedstock, nylon, through melt flow index (MFI) characterization. Differential Scanning Calorimetry (DSC) was used to explore the sintering window of the polymers. Polyethylene and polypropylene exhibited a relatively narrow sintering window between 4 – 5 °C, whereas the sintering window of nylon was much wider, between 23 – 24 °C. This suggests that the print quality between polyethylene and polypropylene would be similar; however, X-ray computed tomography revealed a higher volume of print defects, voids, and de lamination in polyethylene than in polypropylene. MFI analysis provided additional insight into the difference in print quality, as the MFI of polyethylene was 7.16 g/10 min, 9.95 g/10 min for polypropylene, and 17.23 g/10 min for nylon. MFI is inversely correlated to melt viscosity, and a low melt viscosity is desired for proper coalescing between the layers and particles. These results suggest that MFI is a promising tool, in conjunction with traditional thermal analysis, for screening candidate powder feedstocks for SLS and optimization of print parameters for novel powders.
36 MATERIALS SCIENCE↗
Establishing a process-structure-property-performance framework for SLS additive manufacturing through integrated multiscale modeling
This study presents a comprehensive suite of high-fidelity computational models that integrate multiscale and multiphysics simulations to capture the full Selective Laser Sintering (SLS) additive manufacturing process—from initial melting and solidification to mechanical response under external loads. Process simulations are linked with mechanical analysis through Representative Volume Elements (RVEs), establishing a process-structure–property-performance framework. The interaction between laser light and polyamide 12 (PA12) powder is modeled, accounting for laser characteristics and the optical, thermal, and geometrical properties of the powder. The heat source is incorporated into a heat transfer model, coupled with crystallization kinetics and densification models to predict material density and crystallinity. The porosity distribution from the densification model and crystallinity interpolated from experimental data are used to construct the RVEs. A multi-mechanism constitutive model is then calibrated using mechanical tests to predict the stress–strain response. Simulation results show good agreement with experimental data in terms of porosity, crystallinity, and mechanical performance when sufficient laser power (62 W or higher) is used. This research supports the inverse design of 3D-printed structures by introducing a high-fidelity framework that combines multiscale and multiphysics modeling with experimental calibration for predictive and performance-driven additive manufacturing.
SLS↗
Utilization of Additive Manufacturing for the Rapid Prototyping of C-Band Radiofrequency Loads
Additive manufacturing is a versatile technique that shows promise in providing quick and dynamic manufacturing for complex engineering problems. Research has been ongoing into the use of additive manufacturing for potential applications in radiofrequency (RF) component technologies. Here, we present a method for developing an effective prototype load produced from 316L stainless steel on a direct metal laser sintering machine. The model was tested using simulation software to verify the validity of the design. The load structure was manufactured by an online digital manufacturing company, showing the viability of using easily accessible tools to manufacture RF structures. The produced load was able to produce an S11 value of −22.8 dB at a C-band frequency of 5.712 GHz while under a vacuum. In a high-power test, the load was able to terminate a peak power of 8.1 MW. The discussion includes future applications of the present method and how it will help to improve the implementation of future accelerator concepts.
36 MATERIALS SCIENCE↗
Radio Frequency Properties of a 3D Printed Klystron Circuit
The manufacturing of active RF devices like klystrons is dominated by expensive and time-consuming cycles of machining and brazing. In this article, we characterize the RF properties of X-band klystron cavities and an integrated circuit manufactured with a novel additive manufacturing process. Parts are 3D printed in 316 L stainless steel with direct metal laser sintering, electroplated in copper, and brazed in one simple braze cycle. Stand-alone test cavities and integrated circuit cavities were measured throughout the manufacturing process. The un-tuned cavity frequency varies by less than 5% of the intended frequency, and Q factors reach above 1200. A tuning study was performed, and unoptimized tuning pins achieved a tuning range of 138 MHz without compromising Q. Klystron system performance was simulated with as-built cavity parameters and realistic tuning. Together, these results show promise that this process can be used to cheaply and quickly manufacture a new generation of highly integrated high power vacuum devices.
3D printing↗
A Sustainability-Based Expert System for Additive Manufacturing and CNC Machining
The objective of this research study is to develop a set of expert systems that can aid metal manufacturing facilities in selecting binder jetting, direct metal laser sintering, or CNC machining based on viable products, processes, system parameters, and inherent sustainability aspects. For the purposes of this study, cost-effectiveness, energy, and auxiliary material usage efficiency were considered the key indicators of manufacturing process sustainability. The expert systems were developed using the knowledge automation software Exsys Corvid ® V6.1.3. The programs were verified by analyzing and comparing the sustainability impacts of binder jetting and CNC machining during the fabrication of a stainless steel 316L component. According to the results of this study, binder jetting is deemed to be characterized by more favorable indicators of sustainability in comparison to CNC machining, considering the fabrication of components feasible for each technology.
36 MATERIALS SCIENCE↗
Experimental Characterization of an Additively Manufactured Inconel 718 Heat Exchanger for High-Temperature Applications
This work presents the experimental results of a novel, air-to-air, additively manufactured manifold-microchannel heat exchanger with straight fins on both sides. The heat exchanger was made of Inconel 718 using a direct metal laser sintering technique. The overall core size of the heat exchanger was 94 mm × 87.6 mm × 94.4 mm, with a fin thickness of 0.220 mm on both the hot and cold sides. The heat exchanger was tested with pressurized nitrogen gas at 300 °C and 340 kPa for the hot side, while air at an ambient condition was used for the cold side. An overall heat transfer of 276 W/m2K was obtained for Reynolds number values of 132 and 79 for the cold and hot sides, respectively. A gravimetric heat transfer density (Q/m∆T) of 4.7–6.7 W/kgK and a volumetric heat transfer density (Q/V∆T) of 6.9–9.8 kW/m3K were recorded for this heat exchanger with a coefficient of performance value that varied from 42 to 52 over the operating conditions studied here. The experimental pressure drop results were within 10% of the numerical values, while the corresponding heat transfer results were within 17% of the numerical results, mainly due to imperfections in the fabrication process. Despite this penalty, the performance of the tested heat exchanger was superior to the conventional plate-fin heat exchangers: more than 60% of improvements in both gravimetric and volumetric heat transfer densities were recorded for the entire range of experimental data.
42 ENGINEERING↗
Neutron Characterization of 3D Printed Gas Turbine Alloy With Internal Cooling Structure
The objective of this research work is to investigate the residual strains induced by the presence of a exit hole and internal hollow geometry present in a 3D printed IN718 similar to that seen in a gas turbine blade. The specimens were manufactured with an internal hollow structure that ended with an exit hole, and fabricated by direct metal laser sintering additive manufacturing technique. Using this technique, metal powder was melted by a laser source and rapidly cooled to form the part layer by layer. Rapid heating and cooling generate large thermal gradients and residual stresses in the 3D printed material. To be aligned with industry standards, specimens were heat-treated to relieve most of the residual stresses as well as to investigate whether IN718 still preserved a nonhomogeneous stress state after the thermal treatment. Roughness and microstructure analysis was performed to understand the heat-treated sample properties. To investigate the volumetric residual strain, the neutron diffraction technique was used with a definite neutron wavelength. Bragg’s law was used to determine lattice spacing. Interplanar lattice spacing and stress-free state lattice spacings were measured to calculate the strains. Residual strains were measured in the x and y direction to understand the impact of the presence of a exit hole and internal hollow geometry. The results of volumetric residual strain in the x and y directions showed no significant variations in the distribution of the strain due to the presence of a hollow structure as well as the exit hole. Overall, no significant stress concentration was observed in the heat treated sample. Sample geometry, instrumentation for neutron diffraction, and material properties are discussed in detail in this paper.
Raju, Nandhini↗
"Sintering" Models and In-Situ Experiments: Data Assimilation for Microstructure Prediction in SLS Additive Manufacturing of Nylon Components
Selective laser sintering methods are workhorses for additively manufacturing polymer-based components. The ease of rapid prototyping also means it is easy to produce illicit components. It is necessary to have a data-calibrated in-situ physical model of the build process in order to predict expected and defective microstructure characteristics that inform component provenance. Toward this end, sintering models are calibrated and characteristics such as component defects are explored. This is accomplished by assimilating multiple data streams, imaging analysis, and computational model predictions in an adaptive Bayesian parameter estimation algorithm. From these data sources, along with a phase-field model, bulk porosity distributions are inferred. Model parameters are constrained to physically-relevant search directions by sensitivity analysis, and then matched to predictions using adaptive sampling. Using this feedback loop, data-constrained estimates of sintering model parameters along with uncertainty bounds are obtained.
3D printing, Additive Manufacturing, polymer, sint↗
Dry Printing Pure Copper with High Conductivity and Adhesion for Flexible Electronics
Additive manufacturing of functional devices on various rigid and flexible substrates is rising rapidly due to their design flexibility, rapid manufacturing, and lower cost. Current printing technologies are ink-based and focused on printing silver (Ag) as conductive lines due to its matured ink formulation process, low sintering temperature, ease of printing, and low oxidation rate. However, Ag is the 68th most abundant element on Earth, while copper (Cu) is the 25th, making it much cheaper (>100×) while having a comparable conductivity to Ag. Therefore, printing Cu has become technologically and economically more attractive than Ag. Nevertheless, Cu printing is still a significant challenge in ink-based printing methods due to the higher sintering temperature relative to the glass-transition temperature of most flexible substrates, the higher oxidation rate, the challenging ink formulation process, and ink stability concerns. Here, we demonstrate printing highly conductive Cu on flexible polyimide substrates using a dry printing technique. Cu nanoparticles (~3–30 nm) are generated by on-demand laser ablation of a solid Cu target inside the printer head and under argon background gas. These Cu nanoparticles are then transported through a nozzle and onto the substrate, where they are laser-sintered in real time. The argon gas plays three critical roles in laser plume condensation for nanoparticle generation, transport, and sheath gas to avoid oxidation during sintering. The sintered nanoparticles thus show high electrical conductivity and mechanical stability under static and cyclic tests. Our dry printing technique can potentially revolutionize how electronic devices and sensors are additively manufactured for earth and space applications.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Zirconium-diboride silicon-carbide composites: A review
Zirconium diboride (ZrB 2 ) and silicon carbide (SiC) composites have long been of interest since it was observed that ZrB 2 improved the thermal shock resistance of SiC. However, processing of these materials can be difficult due to high and different sintering temperatures and differences in the thermodynamic stability of each material. ZrB 2 –SiC composites have been processed in a variety of ways including hot-pressing, spark-plasma sintering, reactive melt infiltration, pack cementation, chemical vapor deposition, chemical vapor infiltration, stereolithography, direct ink writing, selective laser sintering, electron beam melting, and binder jet additive manufacturing. Each manufacturing method has its own pros and cons. This review serves to summarize more than 60 years of research and provide a coherent resource for the variety of methods and advancements in development of ZrB 2 –SiC composites.
36 MATERIALS SCIENCE↗
Additive manufacturing of silicon carbide for nuclear applications
Additive manufacturing (AM) is a rapidly evolving technology being considered for nuclear applications. A special focus on AM to fabricate nuclear-grade silicon carbide (SiC) is explored in this paper. First, we present currently available AM processing options for SiC. AM methods commonly used for other ceramics, in which the feedstocks are forms of polymers, powders, and/or reactive chemical vapors, are also applicable to SiC. SiC phases are formed by pyrolysis of pre-ceramic polymer, direct reaction of powder precursors, sintering of SiC powders, or chemical vapor deposition/infiltration. Second, we discuss how the different microstructures of SiC materials fabricated by various processing methods affect their behavior in nuclear environments. Third, we discuss state-of-the-art AM technologies for the fabrication of relatively pure SiC, which show great potential to retain its strength under neutron irradiation: (1) binder jet printing followed by chemical vapor infiltration, (2) laser chemical vapor deposition, and (3) selective laser sintering of SiC powders.
36 MATERIALS SCIENCE↗
Optical fields in porous polylactide matrices
Optical fields induced by laser light inside porous polymer matrices (scaffolds) under stimulating effect on cells are investigated. The spectra of light scattering coefficients and anisotropy factors of porous polylactide scaffolds in the visible and near-IR ranges are determined by numerical simulation based on experimental data obtained using a double integrating sphere. Studies are conducted for dry and wet scaffolds fabricated by supercritical fluid foaming and surface-selective laser sintering. The Monte Carlo method is used to calculate the fluence rate distribution under the assumptions of the Henyey – Greenstein phase scattering function and the model phase function of scattering on spherical cavities. It is shown that th e fluence rate distribution mainly depends on the scattering coefficient and the mean cosine of the deflection angle (g-factor). The results obtained are of great practical importance for tissue engineering based on the use of polymeric porous scaffolds with cells to replace tissue defects; they can be used to determine the dose range for laser stimulation of cells. (paper)
72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
Structural integrity of additively manufactured stainless steel with cold sprayed barrier coating under combined cyclic loading
Integration of metal additive manufacturing (AM) and cold spray (CS) technologies provide an unprecedented opportunity to manufacture coated material systems with complex geometrical features. The application of these material systems in functionally critical components requires adequate structural integrity, particularly in the presence of cyclic loading. This article researches the multiaxial fatigue (axial-torsional cyclic loading) behavior of a coated material system consisting of 15Cr-5Ni precipitation-hardening stainless steel (15-5 PH SS) substrate additively manufactured by direct metal laser sintering with a layer of chromium carbide nickel (CrC-Ni) barrier coating deposited by CS. The influence of AM and CS-induced residual stresses on fatigue performance of test specimens was thoroughly studied. Additionally, the effect of surface roughness and processes induced defects were considered to explain the crack growth mechanism. Stresses assessed by synchrotron X-ray diffraction indicated a substantial accumulation of residual stresses, particularly in the outer surface of the as-fabricated 155 PH SS specimens. The state of residual stress was changed notably following the deposition of CrC-Ni coating in the axial, hoop, and radial directions of the fatigue test specimen. Also, CS deposition of CrC-Ni coating caused significant improvement in the surface quality of the additively manufactured components. Fatigue test results indicated, CS deposition of CrC-Ni substantially enhances the fatigue life of the AM-produced 15-5 PH SS substrate in all loading conditions, particularly in the high cycle fatigue regime. The improvement in the fatigue life of the specimens with coating was associated with a reduction in equivalent residual stress at the substrate surface and improvement in the specimens' surface condition (i.e., reduced surface roughness). The fractographic analysis of the specimen indicated the cracks tend to initiate in the surface of both as-fabricated and cold-sprayed specimens. However, the mechanism of crack growth changed notably following the deposition of CrC-Ni coating. The cracks tended to propagate in the planes parallel or with a small deviation from the build layers of the AM-produced specimens. On the other hand, deposition of CrC-Ni coating increased the deviation of crack growth plane from the build layers of the substrate.
36 MATERIALS SCIENCE↗
Shock compression behavior of stainless steel 316L octet-truss lattice structures
Lattice structures offer desirable mechanical properties for applications of energy absorption and impact mitigation but limited research has been carried out on their shock compression behavior. In this work, the shock compression behavior of stainless steel 316L (SS316L) octet-truss lattice structures was investigated through experimental techniques and numerical simulations. Plate impact experiments with high-speed imaging were conducted at impact velocities of 270 – 390 m/s on lattice specimens with 5x5x10 unit cell geometries additively manufactured (AM) using direct metal laser sintering. High-speed imaging together with digital image correlation was used to extract full-field measurements and define a two-wave structure consisting of an elastic wave and planar compaction (shock) wave which propagated along the impact direction. A linear shock velocity versus particle velocity relation was found to approximate the measurements with a unit slope and a linear fit constant equal to the crushing speed. Furthermore, the shock velocity versus particle velocity relation, full-field measurements, and elastic limit together with the Eulerian form of the Rankine-Hugoniot jump conditions were used to find relations for the stress and internal energy behind the shock. Stress behind the shock increased with relative density and particle velocity, and specific internal energy converged to a single curve similar to that of bulk AM SS316L. Explicit finite element analysis using the Johnson-Cook constitutive model demonstrated similar shock behavior observed in experiments and a linear shock velocity versus particle velocity relation and corresponding Hugoniot calculations were found to be in agreement with experimental results. Numerical simulations confirmed negligible effects of exterior versus interior measurements and further validated the application of one-dimensional shock theory.
42 ENGINEERING↗