Search NASA⌕ Search

SEARCH · Search NASA

Results for “low temperature electrolytes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Extending the low-temperature operation of sodium metal batteries combining linear and cyclic ether-based electrolyte solutions

Nonaqueous sodium-based batteries are ideal candidates for the next generation of electrochemical energy storage devices. However, despite the promising performance at ambient temperature, their low-temperature (e.g., < 0 °C) operation is detrimentally affected by the increase in the electrolyte resistance and solid electrolyte interphase (SEI) instability. Here, to circumvent these issues, we propose specific electrolyte formulations comprising linear and cyclic ether-based solvents and sodium trifluoromethanesulfonate salt that are thermally stable down to –150 °C and enable the formation of a stable SEI at low temperatures. When tested in the Na||Na coin cell configuration, the low-temperature electrolytes enable long-term cycling down to –80 °C. Via ex situ physicochemical (e.g., X-ray photoelectron spectroscopy, cryogenic transmission electron microscopy and atomic force microscopy) electrode measurements and density functional theory calculations, we investigate the mechanisms responsible for efficient low-temperature electrochemical performance. We also report the assembly and testing between –20 °C and –60 °C of full Na||Na 3 V 2 (PO 4 ) 3 coin cells. The cell tested at –40 °C shows an initial discharge capacity of 68 mAh g –1 with a capacity retention of approximately 94% after 100 cycles at 22 mA g –1 .

25 ENERGY STORAGE↗
DOE OSTI2020

Low-temperature paddlewheel effect in glassy solid electrolytes

Glasses are promising electrolytes for use in solid-state batteries. Nevertheless, due to their amorphous structure, the mechanisms that underlie their ionic conductivity remain poorly understood. Here, ab initio molecular dynamics is used to characterize migration processes in the prototype glass, 75Li2S–25P2S5. Lithium migration occurs via a mechanism that combines concerted motion of lithium ions with large, quasi-permanent reorientations of PS4 3- anions. This latter effect, known as the ‘paddlewheel’ mechanism, is typically observed in high temperature crystalline polymorphs. In contrast to the behavior of crystalline materials, in the glass paddlewheel dynamics contribute to Lithium-ion mobility at room temperature. Paddlewheel contributions are confirmed by characterizing spatial, temporal, vibrational, and energetic correlations with Lithium motion. Furthermore, the dynamics in the glass differ from those in the stable crystalline analogue, γ-Li3PS4, where anion reorientations are negligible and ion mobility is reduced. These data imply that glasses containing complex anions, and in which covalent network formation is minimized, may exhibit paddlewheel dynamics at low temperature. Consequently, these systems may be fertile ground in the search for new solid electrolytes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Sintering protonic zirconate cells with enhanced electrolysis stability and Faradaic efficiency

The emerging applications of steam electrolysis and electrochemical synthesis at 300–600 °C set stringent requirements on the stability of protonic ceramic cells, which cannot be met by Ce-rich electrolytes. A promising candidate is Ce-free BaZr 0.8 Y 0.2 O 3–δ , but its usage has long been hindered due to the high sintering temperatures required for protonic devices. Here we resolved the issue through a co-sintering process, in which the shrinkage stress of a readily sinterable support layer helps to densify the pure BaZr 0.8 Y 0.2 O 3–δ electrolyte membrane at low temperatures. This approach eliminates Ce and harmful sintering aids in the dense zirconate electrolyte membrane, thereby enhancing the Faradaic efficiency and electrochemical stability, especially under harsh operating conditions. Here, the protonic zirconate cells have exceptional performance and demonstrate stable high-steam pressure electrolysis up to 0.7 atm steam pressure, –2 A cm –2 current density and over 800 h of dynamic operation at 600 °C. Our processing breakthrough enables stabilized protonic cells for demanding applications in future energy infrastructure.

25 ENERGY STORAGE↗
DOE OSTI2021

Energy Arbitrage: Comparison of Options for use with LWR Nuclear Power Plants

Arbitrage is the opportunistic buying and selling of a commodity during local pricing valleys and peaks respectively to maximize economic value. This report evaluates options for energy arbitrage integrated with existing light water reactor (LWR) nuclear power plants (NPPs) where nuclear energy could be stored in a variety of forms and later recovered to generate electrical power during periods when grid electricity demand and pricing are high. The forms of energy storage examined in this report include the potential value of batteries, hydrogen, and thermal energy storage for coupling with nuclear power. Various large demand response options are also analyzed, including the production of liquid nitrogen via air separation and liquefaction, liquefaction of hydrogen, compressed hydrogen, and the cryogenic capture of CO2. Demand response refers to dispatchable loads that can cycle up or down depending on-grid electricity demand to aid in balancing the grid. Large demand response options could dispatch to aid nuclear power stations in avoiding power turndowns by providing an alternate disposition for electrical energy by producing marketable products (e.g., liquid nitrogen, hydrogen, or captured CO2). Static conditions were chosen and analyzed in this report for each option. Dynamic operation or optimization of energy arbitrage or demand response are out of scope for this report. The analysis is based on storage systems with discharge capacities of 500 MW for which various durations of storage and costs of charging (electricity cost) are examined. While the value of thermal energy to an industrial user for flexible plant operations has been previously proven as a business case, this report evaluates costs of hydrogen energy storage and leading thermal energy storage options, and large demand response loads that could be integrated with LWRs in comparison to utility-scale battery storage for use of off-peak nuclear energy. Compilation of this information will be used by the Idaho National Laboratory (INL) RAVEN/HERON systems integration and economics tool to evaluate thermal energy dispatch to industrial users. Relative ranking of energy storage options was done using a levelized cost of storage (LCOS) metric which calculates a rough breakeven cost for the system, taking into account the capital and operating costs as well as the revenue from arbitrage. Table ES1 below shows the LCOS for each of the energy storage options considered. First, in the table, lithium iron (Fe) phosphate batteries are listed as the base case for comparison against the other options. Next is hydrogen storage where most of the hydrogen analyses assumed the hydrogen to be produced using solid oxide electrolytic cell (SOEC) high temperature steam electrolysis (HTSE). The others used existing models of polymer electrolyte membrane (PEM) low temperature electrolysis to produce hydrogen. HTSE performance parameters and costs were taken from existing INL models. Various means were assumed to convert the hydrogen to electricity, including PEM fuel cells (FCs) and a gas turbine mixed in a 30 vol% mixture with natural gas. Physical storage (pressure vessels) and geological storage (natural underground features) were used to store the hydrogen as noted. Geological storage is more economical, but the locations are limited because of the requirement for pre-existing geological formations that will support storage. Thermal energy storage (TES) options were also analyzed including electro-thermal energy storage (ETES) and four different liquid sensible heat TES storage media as noted (Hitec, Hitec XL, Therminol-66, and Dowtherm A). The ETES process considered was modified using existing public documentation on an Echogen process and uses a separate supercritical CO2 charge and discharge cycle with sand as the heat storage media.

25 ENERGY STORAGE↗
DOE OSTI2023

Electrolyte design for Li-ion batteries under extreme operating conditions

The ideal electrolyte for the widely used LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811)||graphite lithium-ion batteries is expected to have the capability of supporting higher voltages (≥4.5 volts), fast charging (≤15 minutes), charging/discharging over a wide temperature range (±60 degrees Celsius) without lithium plating, and non-flammability. No existing electrolyte simultaneously meets all these requirements and electrolyte design is hindered by the absence of an effective guiding principle that addresses the relationships between battery performance, solvation structure and solid-electrolyte-interphase chemistry. Here we report and validate an electrolyte design strategy based on a group of soft solvents that strikes a balance between weak Li+-solvent interactions, sufficient salt dissociation and desired electrochemistry to fulfil all the aforementioned requirements. Remarkably, the 4.5-volt NMC811||graphite coin cells with areal capacities of more than 2.5 milliampere hours per square centimetre retain 75 per cent (54 per cent) of their room-temperature capacity when these cells are charged and discharged at -50 degrees Celsius (-60 degrees Celsius) at a C rate of 0.1C, and the NMC811||graphite pouch cells with lean electrolyte (2.5 grams per ampere hour) achieve stable cycling with an average Coulombic efficiency of more than 99.9 per cent at -30 degrees Celsius. The comprehensive analysis further reveals an impedance matching between the NMC811 cathode and the graphite anode owing to the formation of similar lithium-fluoride-rich interphases, thus effectively avoiding lithium plating at low temperatures. Additionally, this electrolyte design principle can be extended to other alkali-metal-ion batteries operating under extreme conditions.

25 ENERGY STORAGE↗
DOE OSTI2020

Roll-to-roll production of catalyst coated membranes for low-temperature electrolyzers

Here we demonstrate a roll-to-roll (R2R) process for direct coating of anode catalyst layers on a polymer electrolyte membrane for low-temperature water electrolysis. To develop this process, we studied catalyst ink formulation, ink-membrane interactions, and coating quality. The catalyst inks were a mixture of iridium oxide (IrO2) and Nafion in a water and alcohol dispersion medium. The type of alcohol (methanol, ethanol, propanols) and water-to-alcohol ratio were varied to determine their influence on membrane swelling, dispersion quality, and coatability. Interactions of the ink dispersion medium with the membrane were characterized using sessile-drop contact-angle measurements. These measurements show that the ratio of water to alcohol has a strong influence on how rapidly the dispersion media is absorbed by the membrane. Rheology of the catalyst inks was measured to understand the microstructure of the catalyst particles in the ink. This analysis found that 1-propanol leads to better dispersion of the IrO2 particles than ethanol. Small-scale coating samples were prepared to understand coating uniformity and formation of irregularities. Subsequently, two water/1-propanol ratios (90:10 and 75:25) were down-selected for large-scale R2R slot die coating. The R2R catalyst-coated membrane (CCM) coating process increased catalyst layer production throughput by over 500x compared to our standard lab-scale spray coating. The CCMs obtained from this process were tested as single-cell membrane electrode assemblies. They exhibited a cell voltage of 1.91 V at a current density of 2 A/cm2, which is comparable to spray-coated CCMs. In conclusion, the work presented here demonstrates a continuous, scalable manufacturing process that eliminates the need for the decal transfer step typically used in CCM production.

42 ENGINEERING↗
DOE OSTI2024

Trace LiBF 4 Enabling Robust LiF-Rich Interphase for Durable Low-Temperature Lithium-Ion Pouch Cells

Lithium-ion batteries (LIBs) with electrolytes containing lithium tetrafluoroborate (LiBF 4 ) can achieve large capacity retention under low temperature, but the accompanying rapid capacity decay inhibits commercialization. Here, in this study, the impact of LiBF 4 as a supplemental salt to LiPF 6 is systematically investigated using low ethylene carbonate (EC)-content electrolytes, along with a low-melting-point cosolvent. It is found that rational adjustment of the amount of LiBF 4 could not only regulate the interactions of anions and solvents in Li + solvation sheaths but also tune the composition and morphology of solid electrolyte interphase (SEI). It is worth noting that electrolytes with trace amount of LiBF 4 (0.05 M) show synergetic interaction between PF 6 - and Li + and decreased interaction between EC and Li + , achieving a dense and LiF-rich SEI, which enables a 200 mAh pouch cell with less gas generation, long-lived cycling, and higher low-temperature capacity, simultaneously. This work provides new insight into utilizing trace LiBF 4 for stable interface construction of durable low-temperature LIBs.

25 ENERGY STORAGE↗
DOE OSTI2021

High Performance SrFe 0.2 Co 0.4 Mo 0.4 O 3–δ Ceramic Anode Supported Low-Temperature SOFCs

The development of alternative ceramic anodes for low-temperature solid oxide fuel cells (LT-SOFCs) is essential to overcome the inherent challenges such as redox instability and coking associated with Ni-based cermet anodes. Moreover, due to the large electrolyte ohmic loss at low temperature, it is critical to developing an electrode supported cell that allows electrolyte thickness reduction. Here we successfully demonstrated a high performance SrFe 0.2 Co 0.4 Mo 0.4 O 3–δ (SFCM) ceramic anode supported LT-SOFC with a peak power density of 730 mW cm –2 and 300 mW cm –2 at ambitious low temperatures of 550 °C and 450 °C, respectively, in humidified H 2 . The new anode material SFCM exhibits exceptional conductivity of over 30 S cm –1 at 450 °C in humidified H 2 , providing essential current collection capability as an anode backbone appropriate for the infiltration of Ni-gadolinia doped ceria (GDC) electrocatalysts. Compared to conventional Ni-cermet anodes, the nano-sized Ni-GDC particles in our SFCM based electrode significantly improves the cell stability in hydrocarbon gases. We demonstrated a stable long-term operation over a period of 380 h in CH 4 –containing gas mixtures at 450 °C with a voltage degradation rate of 4% per 1000 h at a constant current of 0.2 A*cm –2 . Furthermore, our results demonstrate a high performance ceramic anode with high stability for low temperature operation.

25 ENERGY STORAGE↗
DOE OSTI2023

Selecting the Optimal Fluorinated Ether Co-Solvent for Lithium Metal Batteries

To guide the selection of a suitable fluorinated ether (FE) co -solvent for lithium metal batteries, it is crucial to understand the relationship between the organic structures of the FEs and the electrochemical performance of an FE-containing electrolyte. In this work, 1,1,2,2-tetrafluoro-1-(2,2,2-trifluoroethoxy)ethane (FEE), 1,1,2,2-tetrafluoro-3-(1,1,2,2-tetrafluoroethoxy)-propane (TTE), and 1,2-bis(1,1,2,2-tetrafluoroethoxy)ethane (OFDEE) were chosen as representative FE co-solvents because of their distinct structural properties. The structure-activity relationship between the FEs and the electrochemical performance of Li||LiNi 0.6 Mn 0.2 Co 0.2 O 2 (Li||NMC622) cells was correlated and quantified by Fourier-transform infrared and multi-dimensional nuclear magnetic resonance techniques. Sand's model was also employed to assess the extent of lithium dendrite formation in the cells using various FE electrolytes. The cycling performance of Li||NMC622 cells using different FE co-solvents follows the order FEE > TTE > OFDEE. Further, since the direct measurement of Sand's time is difficult, we introduced relative Sand's time to probe the diffusion behavior of each electrolyte, and the results showed that the best performance was obtained in the electrolyte with the longest relative Sand's time. Moreover, the lithium metal cell using the electrolyte with FEE co-solvent showed similar capacity retention compared with the baseline electrolyte at room temperature, but it demonstrated significantly improved low-temperature performance. The results indicate that FEE is a promising co-solvent candidate for improving the low-temperature performance of lithium metal batteries because it possesses not only non-solvating behavior but also very low viscosity and non-flammability. The advanced electrolyte LiPF 6 -FEC-DMC-FEE enables very stable cycling of lithium metal batteries at various temperatures.

25 ENERGY STORAGE↗
DOE OSTI2024

Electrolyte Design for NMC811||SiO x -Gr Lithium-Ion Batteries with Excellent Low-Temperature and High-Rate Performance

The use of high-nickel NMC811 cathode and SiO x -Gr anode can greatly improve the overall energy densities of lithium-ion batteries. However, the unfavorable solid electrolyte interphase (SEI) layer generated from the decomposition of EC-based electrolytes lead to the poor cycling stability of NMC811||SiO x -Gr cells. Here we report an electrolyte design of 1.5 M LiPF 6 dissolved in FEC/MA/BN 2:2:6 by volume, which can form thin, robust, and homogeneous SEI layer to greatly improve the charge transfer at the electrode-electrolyte interface. Importantly, the designed electrolyte shows an outstanding low temperature performance that it can deliver a capacity of 123.3 mAh g –1 after 50 cycles at −20 °C with a current density of 0.5 C, overwhelming the standard EC-based electrolyte (1.2 M LiPF 6 EC/EMC 3:7 by volume) with a capacity of 35.7 mAh g –1 . The electrolyte also has a superior rate performance that it achieves a capacity of 122.5 mAh g −1 at a high current density of 10 C. Moreover, the LTE electrolyte holds the great potential of extreme fast-charging ability because of the large part of CC contribution in the CCCV charging model at high charging current densities.

Electrochemistry↗
DOE OSTI2022

Tailored Solvation and Interface Structures by Tetrahydrofuran-Derived Electrolyte Facilitates Ultralow Temperature Lithium Metal Battery Operations

Ineffectiveness of Li-ion batteries (LIBs) in cold climates hinders electronics to work in various conditions including frigid environments, despite high demands. Given that intrinsic properties of LIB materials cause this problem, optimized cell chemistries ultimately are required for low-temperature usage. In this study, Li-metal batteries (LMBs) composed of a Li-metal anode (LMA) stabilized by a localized high-concentration electrolyte (LHCE) are found to significantly enhance low-temperature performance. The LHCE allows the LMA to have compact and regular deposition and excellent plating/stripping efficiency at sub-zero temperatures. The LHCE produces an inorganic-rich solid-electrolyte interphase with larger amounts of Li 2 O/LiF interfaces, dominance of ion aggregates in Li + solvation, and enhanced Li + transport, which can greatly improve the LMA stability. LMB full cells based on LiNi 0.8 Co 0.1 Mn 0.1 O 2 cathodes with the tailored electrolyte show high retentions of 75 and 64 % at -20 and -40 °C, respectively. Furthermore, the LMB configuration retains its charge-discharge capability even at -60 °C.

25 ENERGY STORAGE↗
DOE OSTI2024

A Carbonyl and Azo-Based Polymer Cathode for Low-Temperature Na-Ion Batteries

Due to flexible structure tunability and abundant structure diversity, redox-active polymers are promising cathode materials for developing affordable and sustainable Na-ion batteries (NIBs). However, polymer cathodes still suffer from low capacity, poor cycle life, and sluggish reaction kinetics. Herein, we designed and synthesized a polymer cathode material bearing carbonyl and azo groups as well as extended conjugation structures in the repeating units. The polymer cathode exhibited exceptional electrochemical performance in NIBs in terms of high capacity, long lifetime, and fast kinetics. When coupled with a low-concentration electrolyte, it shows superior performance at low temperatures down to -50 °C, demonstrating great promise for low-temperature battery applications. Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) were employed to study the reaction mechanism, interphase structure, and morphological evolution, confirming reversible redox reactions between azo/carbonyl groups in the polymer and Na + /electrons, a NaF-rich interphase, and high structure stability upon cycling. In conclusion, this work provides an effective approach to developing high-performance polymer cathodes for affordable, sustainable, and low-temperature NIBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Methyl Carbamate-Lithium Salt Deep Eutectic Electrolyte for Lithium-Ion Batteries

Deep eutectic electrolytes (DEEs) represent a burgeoning field in electrolytes for energy storage applications. Compared to the more conventionally studied Li-ion electrolyte systems, these electrolytes offer numerous advantages, such as high ion concentration, costs, lower temperature operation, and safety. In this work, the formation of a novel eutectic electrolyte based on lithium salts and methyl carbamate was reported. These DEEs were formed via mixing lithium salts and low-cost methyl carbamate at ratios varying from 1:2 to 1:5 (mol:mol). Here, the DEE formed from methyl carbamate and lithium hexafluorophosphate (LiPF 6 ) at a 1:5 molar ratio generated a 4V stability window and a 25°C conductivity of up to 3.16E –3 S cm –1 . The DEE formed from methyl carbamate and lithium bis(trifluoromethane)sulfonimide (LiTFSI) at a 1:5 molar ratio generated a 3.2 V stability window and a 25°C conductivity of up to 2.87E –3 S cm –1 . The LiPF 6 DEE also demonstrated a discharge capacity of 128 mAh g –1 after 50 cycles with 93% discharge capacity retention at moderate cycling rates of 0.5C in a lithium titanate (LTO)/lithium iron phosphate (LFP) full cell. These results demonstrate the potential for methyl carbamate to generate eutectics from lithium salts and offer alternative electrolytes for use in low-temperature Li-ion battery applications.

25 ENERGY STORAGE↗
DOE OSTI2024

Shape Matters: Understanding the Effect of Electrode Geometry on Cell Resistance and Chemo-Mechanical Stress

Rechargeable batteries that incorporate shaped three-dimensional electrodes have been shown to have increased power and energy densities when compared to a conventional geometry, i.e. a planar cathode and anode that sandwich an electrolyte. Electrodes can be shaped to enable a higher active material loading, while keeping ion transport distances small. However, the relationship between electrical and mechanical performance of shaped electrodes remains poorly understood. Many electrode designs have been explored, where the electrodes are individually shaped or intertwined, and advances in manufacturing and shape/topology optimization have made such designs a reality. Here, we explore sinusoidal half cells and interdigitated full cells. First, we use a simple electrostatics model to understand the cell resistance as a function of shape. Here we focus on low-temperature conditions, where the electrolyte conductivity decreases relative to that of the electrode; here, LiPF 6 EC:DMC electrolyte and MnO 2 electrode are considered. Next, we use a chemo-mechanics model to examine the stress that arises due to intercalation-driven volume expansion. We show that shaped electrodes provide a significant reduction in resistance in low-temperature conditions, however, they exhibit unfavorable stress concentrations. Overall, we find that the fully interdigitated electrodes may provide the best balance with respect to this resistance-stress trade-off.

25 ENERGY STORAGE↗
DOE OSTI2024

Low‐Temperature and High‐Rate Rechargeable Aluminum Batteries Enabled by Ternary Eutectic Electrolytes

Abstract Rechargeable aluminum batteries (RABs) have garnered extensive scientific attention as a promising alternative chemistry due to the inherent advantages associated with aluminum (Al) metal anodes, including their high theoretical capacities, cost‐effectiveness, environmental friendliness, and inherent non‐flammable properties. Nonetheless, the practical energy density of RABs is constrained by the electrolytes that support lower operational voltage windows. Herein, we report a ternary eutectic electrolyte composed of 1‐ethyl‐3‐methylimidazolium chloride ([C 2 C 1 im]Cl):1‐butyl‐3‐methylimidazolium chloride ([C 4 C 1 im]Cl):aluminum chloride (AlCl 3 ) for the application of RABs. The electrolyte exhibits a high operational potential window (~3 V vs. Al/Al 3+ on SS 316) and high ionic conductivity (~8.3 mS cm −1 ) while exhibiting only a low temperature glass transition at −65 °C suitable for all‐climate conditions. Al||graphene nanoplatelets cell delivers a high capacity of ~117 mAh/g, and ~43 mAh/g at a very high current densities of 1 A/g and 5 A/g, respectively. The cells render a reversible capacity of 20 mAh/g at −20 °C and 17 mAh/g at −40 °C, indicating their suitability for operation under extreme environmental conditions. We comprehensively evaluated the design and optimization of carbon paper‐based battery systems. The ternary eutectic electrolyte demonstrates exceptional electrochemical performance, thus signifying its substantial potential for utilization in high‐performance energy storage systems in all climates.

Vadthya, Raju↗
DOE OSTI2022

Investigation of the Electrode-Electrolyte Interphase in Ester-Based Electrolytes in NCM523/Graphite Cells

The use of methyl acetate (MA) and methyl propionate (MP) as co-solvents in carbonate/LiPF 6 electrolytes have been investigated in LiNi 0.5 Co 0.2 Mn 0.3 O 2 (NCM523)/graphite cells to improve electrochemical performance at low temperature (−20 °C). Consistent with previous investigations, improved low temperature performance was observed with all electrolyte formulations containing esters. Detailed ex situ surface analysis of the surface films generated with the ester-based electrolytes containing electrolyte additives reveal significant changes to the SEI on graphite upon cycling at moderately elevated temperature (45 °C). In the presence of vinylene carbonate (VC) lithium plating is observed upon cycling at low temperature (−20 °C) which leads to a thicker solid electrolyte interface (SEI) upon cycling at 45 °C. Incorporation of fluoroethylene carbonate (FEC) as an electrolyte additive results in the generation of a thin SEI and alters the structure of the surface film on the NCM523 cathode resulting in stable cycling over a wide temperature range.

Rodrigo, Nuwanthi D. (ORCID:0000000343129536)↗