Search NASA⌕ Search

SEARCH · Search NASA

Results for “lunar core”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

On the detectability of a metallized lunar core

Calculations are made of the expected complex electromagnetic gain of the moon using current models of the internal bulk electrical conductivity with the addition of conducting cores of varying radii. The results show that the phase of the response (gain) function is sensitive to the radius and conductivity. The gain amplitude varies in a complicated way for frequencies above (0) 10 microHz. Below this 'corner' frequency, the square of the gain amplitude varies approximately quadratically with frequency and therefore inverse quadratically with hydromagnetic wavelength in the solar wind. The addition of conducting cores alters this dependence. A 'flat' frequency independent range for the gain amplitude evolves, which is a second way, in principle, to detect a conducting core. The departure from the lambda to the -4th Rayleigh scattering law is due to a combination of the conductivity of the moon and the relative unimportance of confinement of the induced fields at the very low frequencies of interest for core detection. For some core parameters, detection is not feasible with current data, and data recording times varying from several months to centuries would be required.

Wiskerchen, M. J.↗
NASA NTRS1980

Thermal conduction in a composite circular cylinder: A new technique for thermal conductivity measurements of lunar core samples

The core sample is heated from the outside at a known rate and the rise in temperature at the surface of the core tube is measured. Because the temperature at the surface, increasing with time, is a function of the thermal properties of both the core tube and the sample, the thermal properties of the sample can be estimated by comparing the measured temperature with the theory, provided that the thermal properties of the core tube are known. Thus it is not necessary to extract the sample from the core tube to make the measurements. Neither is it necessary to insert a heater, or temperature sensor, into the sample within the core tube, as would be required if another method were applied. The sample remains intact after the measurements. The temperature change in the sample can be kept to a minimum as long as the thermal conductivity determination is possible with a reasonable precision. If the radiative method of heat transfer is chosen, the core tube will only be in mechanical contact with the sample holder and a sensor attached to the core tube to measure the surface temperature, thereby greatly reducing the possibility of disturbing the sample.

Horai, K.↗
NASA NTRS1980

Lunar core 15010/11 - Grain size, petrology, and implications for regolith dynamics

Petrographic observations of six samples from various depths show that core 15010/11 is relatively homogeneous and consists mostly of basalt fragments and minerals derived from basalts. However, it also contains an appreciable highland component nearly equally distributed among the fine-grained fraction, dark matrix breccia and identifiable highland grains, and agglutinates. Grain size data and agglutinates show that this core is not mature and does not contain a well developed reworking profile. The unusual properties of the core are thought to be a direct result of its close proximity to the rim of Hadley Rille. This location favors relatively rapid regolith erosion into the rille, produces a thin regolith, and provides an abundant supply of bedrock-derived ejecta.

Mckay, D. S.↗
NASA NTRS1984

On the Apollo subsatellite evidence for a lunar core

Two independent techniques used to infer the electrical conductivity of the interior of the Moon are discussed. The first is the measurement of an incident spectrum of electromagnetic waves in the solar wind near the Moon and the separate measurement of the incident plus reflected spectrum on the surface of the Moon. The second is the measurement of the distortion of the ambient magnetic field of the geomagnetic tail lobes by the conducting Moon. The size of the conducting region was found to be greater than 400 km in radius.

Russell, C. T.↗
NASA NTRSDate not supplied

Determining Surface Exposure Ages of Regolith Grains in Lunar Core Sample 73002 By Investigating Solar Particle Irradiation Damage

Space weathering causes the surface soils of airless bodies like the Moon to be micro-structurally and chemically altered by exposure to micrometeoroid bombardment and solar wind irradiation. These alterations accumulate in surface grains with continued residence in the uppermost millimeters of regolith. Low energy solar wind ions (largely H+ and He+) produce a layer of radiation damage as they become implanted in grain surfaces. Also present are solar energetic particle (SEP) tracks, which are nanoscale lineations within grain interiors formed by heavy, high-energy ions (mainly Fe group nuclei) penetrating up to millimeters below the surface. Recent work has determined that the width of solar wind-damaged rims on anorthite and olivine, and their respective SEP track densities are correlated with each other and with grain surface exposure age. Core sample 73002, recently released under the Apollo Next Generation Sample Analysis (ANGSA) Program, has provided an opportunity to study material collected from the light mantle formation in the Taurus-Littrow Valley during Apollo 17. The light mantle is thought to have been deposited vial and slide originating from the neighboring South Massif. Spectral analysis of bulk core soils found a plagioclase rich composition, confirming a highlands origin of the formation. Spectral profiles and ferromagnetic resonance (FMR) measurements of bulk soils sampled at cm-intervals from 73002 indicate that regolith up to~9.5 cm in depth have maturity indices consistent with longer durations of surface processing than samples deeper in the core. Thus, this upper ~9 cm layer likely represents the maximum extent of an in-situ reworking zone which may have persisted over 5 to 17million years. Here we present an analysis of grain exposure ages within the in-situ reworking zone of 73002derived from SEP track density measurements via transmission electron microscopy.

J A McFadden↗
NASA NTRS1976

Properties of the moon and its environment from lunar magnetometer measurements

Lunar analysis of data from a total of nine lunar magnetometers is described. Results obtained concerning electromagnetic, compositional, and structural properties of the lunar interior are discussed. Specific topics covered include: lunar magnetic permeability and iron abundance; limits on a highly conducting lunar core; lunar electrical conductivity; and internal structure inferred from conductivity and permeability results.

Parkin, C. W.↗
NASA NTRS1990

Lunar Polar Coring Lander

Plans to build a lunar base are presently being studied with a number of considerations. One of the most important considerations is qualifying the presence of water on the Moon. The existence of water on the Moon implies that future lunar settlements may be able to use this resource to produce things such as drinking water and rocket fuel. Due to the very high cost of transporting these materials to the Moon, in situ production could save billions of dollars in operating costs of the lunar base. Scientists have suggested that the polar regions of the Moon may contain some amounts of water ice in the regolith. Six possible mission scenarios are suggested which would allow lunar polar soil samples to be collected for analysis. The options presented are: remote sensing satellite, two unmanned robotic lunar coring missions (one is a sample return and one is a data return only), two combined manned and robotic polar coring missions, and one fully manned core retrieval mission. One of the combined manned and robotic missions has been singled out for detailed analysis. This mission proposes sending at least three unmanned robotic landers to the lunar pole to take core samples as deep as 15 meters. Upon successful completion of the coring operations, a manned mission would be sent to retrieve the samples and perform extensive experiments of the polar region. Man's first step in returning to the Moon is recommended to investigate the issue of lunar polar water. The potential benefits of lunar water more than warrant sending either astronauts, robots or both to the Moon before any permanent facility is constructed.

Angell, David↗
NASA NTRS1977

New data for the lunar 20 core and a survey of published chemical data

Lunar core samples were analyzed using a spark source mass spectrometer. The analytical results for the four zones of the Lunar 20 core suggest that the core is nonuniform with depth. The higher concentrations of Ce, Sc, Sc, Ba, La, Co, Sr, and Zr in zone 2001 may be connected with the presence in this zone of a basaltic rock type seldom seen in the other zones. That is, about half of the basaltic fragments in the large size fractions in zone 2001 are of a specific porphyritic breccia-like type. Anorthositic fragments containing a notable amount of metallic iron are basically limited to zone 2004 and probably explain the lower concentrations of Ce, Rb, Ba, La, and perhaps Co in this zone. The high concentrations of Ag and Ce found previously are confirmed. Although Ag is at nearly the same concentration in all four zones of the core, Cd in the core is the result of local enrichment. In particular, in zone 2004 the concentration of Cd may be as high as 10 ppm in a sample size of 0.01 mg.

Hubbard, N. J.↗
NASA NTRS1980

Multispectral imaging of the lunar regolith core samples - Preliminary results for 74002

Multispectral images of a lunar core segment are a new form of continuous data along the length of the core. A new laboratory arrangement was developed to obtain these images. Data processing and initial data analysis for core section 74002 were performed. The images are sensitive to variations in mineralogy and/or maturity of the soil and are easily used (1) in stratigraphic studies of the lunar regolith, (2) for sample selection of representative material, and (3) as ground truth for remote sensing studies.

Pieters, C. M.↗
NASA NTRS1977

A lunar metal core

Recent work generally supports the hypothesis of a centrally condensed lunar core. Data regarding the axial moment on the basis of laser tracking and satellite orbit analyses place an upper limit of about 500 km on an Fe core, or 700 km upon an Fe/FeS core, if differentiation in the lithosphere is ignored. Whether a metallized core exists in the moon has a profound bearing upon the question of the origin of the magnetic fields responsible for the present day magnetization on the lunar surface. Recent efforts to examine in detail signals arising from lunar induction at very low frequency are discussed. The discussion represents an extension of a study reported by Wiskerchen et al. (1976). The present data base consists of all Apollo 12 data which fulfill the requirement that the surface magnetometer be on the sunward side of the moon and at least 10 deg from the lunar optical terminator. It is found that only marginal evidence exists for a metallized core at a radius of 400 km in the moon.

Wiskerchen, M. J.↗
NASA NTRS2005

Lunar Fluid Core and Solid-Body Tides

Variations in rotation and orientation of the Moon are sensitive to solid-body tidal dissipation, dissipation due to relative motion at the fluid-core/solid-mantle boundary, and tidal Love number k2 [1,2]. There is weaker sensitivity to flattening of the core-mantle boundary (CMB) [2-5] and fluid core moment of inertia [1]. Accurate Lunar Laser Ranging (LLR) measurements of the distance from observatories on the Earth to four retroreflector arrays on the Moon are sensitive to lunar rotation and orientation variations and tidal displacements. Past solutions using the LLR data have given results for dissipation due to solid-body tides and fluid core [1] plus Love number [1-5]. Detection of CMB flattening has been improving [3,5] and now seems significant. This strengthens the case for a fluid lunar core.

Williams, J. G.↗
NASA NTRS2011

Imaging the Moon's Core with Seismology

Constraining the structure of the lunar core is necessary to improve our understanding of the present-day thermal structure of the interior and the history of a lunar dynamo, as well as the origin and thermal and compositional evolution of the Moon. We analyze Apollo deep moonquake seismograms using terrestrial array processing methods to search for the presence of reflected and converted energy from the lunar core. Although moonquake fault parameters are not constrained, we first explore a suite of theoretical focal spheres to verify that fault planes exist that can produce favorable core reflection amplitudes relative to direct up-going energy at the Apollo stations. Beginning with stacks of event seismograms from the known distribution of deep moonquake clusters, we apply a polarization filter to account for the effects of seismic scattering that (a) partitions energy away from expected components of ground motion, and (b) obscures all but the main P- and S-wave arrivals. The filtered traces are then shifted to the predicted arrival time of a core phase (e.g. PcP) and stacked to enhance subtle arrivals associated with the Moon s core. This combination of filtering and array processing is well suited for detecting deep lunar seismic reflections, since we do not expect scattered wave energy from near surface (or deeper) structure recorded at varying epicentral distances and stations from varying moonquakes at varying depths to stack coherently. Our results indicate the presence of a solid inner and fluid outer core, overlain by a partial-melt-containing boundary layer (Table 1). These layers are consistently observed among stacks from four classes of reflections: P-to-P, S-to-P, P-to-S, and S-to-S, and are consistent with current indirect geophysical estimates of core and deep mantle properties, including mass, moment of inertia, lunar laser ranging, and electromagnetic induction. Future refinements are expected following the successful launch of the GRAIL lunar orbiter and SELENE 2 lunar lander missions.

Weber, Renee C.↗
NASA NTRS2005

The Core of the Moon - Molten or Solid?

While several studies beginning in the Apollo era and continuing up to the present have tried to detect the lunar core, either geochemically, geophysically or geologically [e.g. 1, 2, 3, 4], it has so far proven somewhat elusive. The unambiguous detection of the lunar core is of prime importance as it holds the potential of distinguishing between the various theories for the formation of the Moon. The theory which currently enjoys the greatest success is the giant impact model, which has the Moon forming about 4.5 Gyr ago from the debris produced when a Mars sized proto planet collided with the proto Earth [e.g. 5, 6]. Simulations reveal that the material from which the Moon is made up contains very little iron and consequently a lunar core, if it exists, should be small.

Khan, A.↗
NASA NTRS2011

Further Constraints and Uncertainties on the Deep Seismic Structure of the Moon

The Apollo Passive Seismic Experiment (APSE) consisted of four 3-component seismometers deployed between 1969 and 1972, that continuously recorded lunar ground motion until late 1977. The APSE data provide a unique opportunity for investigating the interior of a planet other than Earth, generating the most direct constraints on the elastic structure, and hence the thermal and compositional evolution of the Moon. Owing to the lack of far side moonquakes, past seismic models of the lunar interior were unable to constrain the lowermost 500 km of the interior. Recently, array methodologies aimed at detecting deep lunar seismic reflections found evidence for a lunar core, providing an elastic model of the deepest lunar interior consistent with geodetic parameters. Here we study the uncertainties in these models associated with the double array stacking of deep moonquakes for imaging deep reflectors in the Moon. We investigate the dependency of the array stacking results on a suite of parameters, including amplitude normalization assumptions, polarization filters, assumed velocity structure, and seismic phases that interfere with our desired target phases. These efforts are facilitated by the generation of synthetic seismograms at high frequencies (approx. 1Hz), allowing us to directly study the trade-offs between different parameters. We also investigate expected amplitudes of deep reflections relative to direct P and S arrivals, including predictions from arbitrarily oriented focal mechanisms in our synthetics. Results from separate versus combined station stacking help to establish the robustness of stacks. Synthetics for every path geometry of data were processed identically to that done with data. Different experiments were aimed at examining various processing assumptions, such as adding random noise to synthetics and mixing 3 components to some degree. The principal stacked energy peaks put forth in recent work persist, but their amplitude (which maps into reflector impedance contrast) and timing (which maps into reflector depth) depend on factors that are not well constrained -- most notably, the velocity structure of the overlying lunar interior. Thus, while evidence for the lunar core remains strong, the depths of imaged reflectors have associated uncertainties that will require new seismic data and observations to constrain. These results strongly advocate further investigations on the Moon to better resolve the interior (e.g., Selene missions), for the Moon apparently has a rich history of construction and evolution that is inextricably tied to that of Earth.

Lin, Pei-Ying Patty↗
NASA NTRS2004

Lunar and Planetary Science XXXV: Lunar Geophysics: Rockin' and a-Reelin'

This document contained the following topics: The Influence of Tidal, Despinning, and Magma Ocean Cooling Stresses on the Magnitude and Orientation of the Moon#s Early Global Stress Field; New Approach to Development of Moon Rotation Theory; Lunar Core and Tides; Lunar Interior Studies Using Lunar Prospector Line-of-Sight Acceleration Data; A First Crustal Thickness Map of the Moon with Apollo Seismic Data; New Events Discovered in the Apollo Lunar Seismic Data; More Far-Side Deep Moonquake Nests Discovered; and Manifestation of Gas-Dust Streams from Double Stars on Lunar Seismicity.

Source record↗