Search NASA⌕ Search

SEARCH · Search NASA

Results for “mechanical performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Powder metallurgy processing of high strength turbine disk alloys

Using vacuum-atomized AF2-1DA and Mar-M432 powders, full-scale gas turbine engine disks were fabricated by hot isostatically pressing (HIP) billets which were then isothermally forged using the Pratt & Whitney Aircraft GATORIZING forging process. While a sound forging was produced in the AF2-1DA, a container leak had occurred in the Mar-M432 billet during HIP. This resulted in billet cracking during forging. In-process control procedures were developed to identify such leaks. The AF2-1DA forging was heat treated and metallographic and mechanical property evaluation was performed. Mechanical properties exceeded those of Astroloy, one of the highest temperature capability turbine disk alloys presently used.

Evans, D. J.↗
NASA NTRS1978

Performance degradation mechanisms and modes in terrestrial photovoltaic arrays and technology for their diagnosis

Accelerated life-prediction test methodologies have been developed for the validation of a 20-year service life for low-cost photovoltaic arrays. Array failure modes, relevant materials property changes, and primary degradation mechanisms are discussed as a prerequisite to identifying suitable measurement techniques and instruments. Measurements must provide sufficient confidence to permit selection among alternative designs and materials and to stimulate widespread deployment of such arrays. Furthermore, the diversity of candidate materials and designs, and the variety of potential environmental stress combinations, degradation mechanisms and failure modes require that combinations of measurement techniques be identified which are suitable for the characterization of various encapsulation system-cell structure-environment combinations.

Noel, G. T.↗
NASA NTRS1980

Determination of efficiencies, loss mechanisms, and performance degradation factors in chopper controlled dc vehical motors. Section 2: The time dependent finite element modeling of the electromagnetic field in electrical machines: Methods and applications

The time dependent solution of the magnetic field is introduced as a method for accounting for the variation, in time, of the machine parameters in predicting and analyzing the performance of the electrical machines. The method of time dependent finite element was used in combination with an also time dependent construction of a grid for the air gap region. The Maxwell stress tensor was used to calculate the airgap torque from the magnetic vector potential distribution. Incremental inductances were defined and calculated as functions of time, depending on eddy currents and saturation. The currents in all the machine circuits were calculated in the time domain based on these inductances, which were continuously updated. The method was applied to a chopper controlled DC series motor used for electric vehicle drive, and to a salient pole sychronous motor with damper bars. Simulation results were compared to experimentally obtained ones.

Hamilton, H. B.↗
NASA NTRS2006

Advances in Hot-Structure Development

The National Aeronautics and Space Administration has actively participated in the development of hot structures technology for application to hypersonic flight systems. Hot structures have been developed for vehicles including the X-43A, X-37, and the Space Shuttle. These trans-atmospheric and atmospheric entry flight systems that incorporate hot-structures technology are lighter weight and require less maintenance than those that incorporate parasitic, thermal-protection materials that attach to warm or cool substructure. The development of hot structures requires a thorough understanding of material performance in an extreme environment, boundary conditions and load interactions, structural joint performance, and thermal and mechanical performance of integrated structural systems that operate at temperatures ranging from 1500 C to 3000 C, depending on the application. This paper will present recent advances in the development of hot structures, including development of environmentally durable, high temperature leading edges and control surfaces, integrated thermal protection systems, and repair technologies. The X-43A Mach-10 vehicle utilized carbon/carbon (C/C) leading edges on the nose, horizontal control surface, and vertical tail. The nose and vertical and horizontal tail leading edges were fabricated out of a 3:1 biased, high thermal conductivity C/C. The leading edges were coated with a three-layer coating comprised of a SiC conversion of the C/C, followed by a CVD layer of SiC, followed by a thin CVD layer of HfC. Work has also been performed on the development of an integrated structure and was focused on both hot and warm (insulated) structures and integrated fuselage/tank/TPS systems. The objective was to develop integrated multifunctional airframe structures that eliminate fragile external thermal-protection systems and incorporate the insulating function within the structure. The approach taken to achieve this goal was to develop candidate hypersonic airframe concepts, including structural arrangement, load paths, thermal-structural wall design, thermal accommodation features, and integration of major components, optimize thermalstructural configurations, and validate concepts through a building block test program and generate data to improve and validate analytical and design tools.

Rivers, H. Kevin↗
NASA NTRSDate not supplied

The Effect of Fiber-Angle Fidelity on the Linear Response of Tow-steered Composite Plates

Composite laminate tailoring is traditionally performed by uniformly changing the in-plane ply orientation to obtain the desired mechanical performance. The emergence of tow-steered plies, where the fibers follow a prescribed curvilinear path, have increased the tailorability of composite laminates. However, characterizing the behavior of tow-steered laminates using finite element analysis is challenging because additional, and often numerous, orientation definitions may be required. The additional orientation definitions detrimentally increase the computational cost and hinder the use of advanced analysis techniques, such as Monte Carlo or uncertainty quantification, in the design process. To reduce computational cost without adversely affecting mechanics-based performance, the results of a parametric study that was used to investigate the effects of fiber-angle fidelity, element size, and tow-steered radius-of-curvature on various loading scenarios for tow-steered composite plates are presented. The three loading scenarios that were analyzed using finite element analysis included an axial tension load, an applied constant through-thickness-direction pressure load, and an axial compression load. Results for mechanics-based metrics of interest are presented and discussed for each loading scenario. Little sensitivity (less than one percent difference) to the effect of fiber-angle fidelity is observed in the mechanics-based metrics until the coarse-end of the considered range. Sensitivity to element size generally dominates the observed results for the mechanics-based metrics. Notable reductions in the preprocessing time are observed for increasingly coarse element size and fiber-rounding parameters. The preprocessing times decreased up to three orders of magnitude from a few thousand seconds to a few seconds without loss of accuracy in the mechanics-based metrics. Such increased computational performance is of particular interest to the structural design and analysis communities that may be conducting large counts of finite-element analyses, such as in other parametric studies, Monte-Carlo analyses, uncertainty quantification, or tow-steered optimization.

tow-steered composites↗
NASA NTRS1999

Teleoperation, Telerobotics

In a general sense, teleoperator devices enable human operators to remotely perform mechanical actions that usually are performed by the human arm and hand.

applications↗
NASA NTRSDate not supplied

Advanced Supersonic Parachute Inflation Research Experiment 2 (ASPIRE2) Flight Mechanics and Parachute Performance

The Advanced Supersonic Parachute Inflation Re-search Experiment-2 (ASPIRE2) program consists of a sounding rocket flight test to be launched at Wallops Flight Facility (WFF) in 2025. This effort seeks to qualify the supersonic parachute for the Sample Retrieval Lander (SRL) under the Mars Sample Return (MSR) program, building off the successes of its predecessor program, ASPIRE, which launched in both 2017 and 2018. The conops for the ASPIRE2 mission are shown in Figure 1 relative to its predecessor. While the ASPIRE pro-gram qualified a 21.5 m diameter disk-gap band parachute deployed at Mach 1.7, the SRL parachute will be increased to 24 m in diameter and target a Mach 2.1 parachute deployment condition, the largest diameter supersonic parachute deployed at the highest Mach number to date. These requirements are driven by the increased landing mass of the sample retrieval lander, which is roughly a 50% increase over that of the Mars2020 entry vehicle. These changes necessitate ASPIRE2 to certify the parachute performance under similar deployment conditions. This work will cover the 6-DoF para-chute model implementation and flight mechanics performance for the ASPIRE2 campaign and discuss how these results will impact the design of the test article. The ASPIRE2 trajectory is simulated using a multi-body flight dynamics tool, Program to Optimize Simulated Trajectories II (POST2). This work will summarize both the flight mechanics and parachute modeling (from payload separation until splashdown) and performance for this mission. Various design trades will be assessed such as para-chute tuning parameters as well as vehicle center of gravity location.

Evan Roelke↗
NASA NTRS1979

Development and evaluation of an ablative closeout material for solid rocket booster thermal protection system

A trowellable closeout/repair material designated as MTA-2 was developed and evaluated for use on the Solid Rocket Booster. This material is composed of an epoxy-polysulfide binder and is highly filled with phenolic microballoons for density control and ablative performance. Mechanical property testing and thermal testing were performed in a wind tunnel to simulate the combined Solid Rocket Booster trajectory aeroshear and heating environments. The material is characterized by excellent thermal performance and was used extensively on the Space Shuttle STS-1 and STS-2 flight hardware.

Patterson, W. J.↗
NASA NTRS1986

Sulfone/Ester Polymers Containing Pendent Ethynyl Groups

Two processes make high-performance polymers resistant to solvents, without compromising mechanical characteristics. Polymers show improved solvent resistance while retaining high toughness, thermoformability, and mechanical performance. Multistep process involves conversion of pendent bromo group to ethynyl group, while direct process involves reacting hydroxy-terminated sulfone oligomers or polymers with stoichiometric amount of 5-(4-ethynylphenoxy) isophthaloyl chloride. Applications for new polymers include adhesives, composite resin matrices, moldings, ultrafiltration membranes, protective coatings, and such electrical insulators as thin films for microelectronic circuitry.

Hergenrother, P. M.↗
NASA NTRS1997

Solar and Magnetic Attitude Determination for Small Spacecraft

During the Phase B development of the NASA New Millennium Program (NMP) Earth Orbiter-1 (EO-1) spacecraft, detailed analyses were performed for on-board attitude determination using the Sun and the Earth's magnetic field. This work utilized the TRMM 'Contingency Mode' as a starting point but concentrated on implementation for a small spacecraft without a high performance mechanical gyro package. The analyses and simulations performed demonstrate a geographic dependence due to diurnal variations in the Earth magnetic field with respect to the Sun synchronous, nearly polar orbit. Sensitivity to uncompensated residual magnetic fields of the spacecraft and field modeling errors is shown to be the most significant obstacle for maximizing performance. Performance has been evaluated with a number of inertial reference units and various mounting orientations for the two-axis Fine Sun Sensors. Attitude determination accuracy using the six state Kalman Filter executing at 2 Hz is approximately 0.2 deg, 3-sigma, per axis. Although EO-1 was subsequently driven to a stellar-based attitude determination system as a result of tighter pointing requirements, solar/magnetic attitude determination is demonstrated to be applicable to a range of small spacecraft with medium precision pointing requirements.

Woodham, Kurt↗
NASA NTRS2010

Comparison of Autoclave and Out-of-Autoclave Composites

The National Aeronautics and Space Administration (NASA) Exploration Systems Mission Directorate initiated an Advanced Composite Technology Project through the Exploration Technology Development Program in order to support the polymer composite needs for future heavy lift launch architectures. As an example, the large composite dry structural applications on Ares V inspired the evaluation of autoclave and out-of-autoclave (OOA) composite materials. A NASA and industry team selected the most appropriate materials based on component requirements for a heavy lift launch vehicle. Autoclaved and OOA composites were fabricated and results will highlight differences in processing conditions, laminate quality, as well as initial room temperature thermal and mechanical performance. Results from this study compare solid laminates that were both fiber-placed and hand-laid. Due to the large size of heavy-lift launch vehicle composite structures, there is significant potential that the uncured composite material or prepreg will experience significant out-life during component fabrication. Therefore, prepreg out-life was a critical factor examined in this comparison. In order to rigorously test material suppliers recommended out-life, the NASA/Industry team extended the out-time of the uncured composite prepreg to values that were approximately 50% beyond the manufacturers out-time limits. Early results indicate that the OOA prepreg composite materials suffered in both composite quality and mechanical property performance from their extended out-time. However, the OOA materials performed similarly to the autoclaved composites when processed within a few days of exposure to ambient "shop" floor handling. Follow on studies evaluating autoclave and OOA aluminum honeycomb core sandwich composites are planned.

Sutter, James K.↗
NASA NTRS2023

3D Printed TiO 2 Negative Electrodes for Sodium-Ion and Lithium-ion Batteries using Vat Photopolymerization

Additive manufacturing, also called 3D printing, represents a unique approach to develop three dimensional shape-conformable batteries with enhanced electrodes, specific surface area, improved ion diffusion, and power. For the first time, the formulation of a composite photocurable resin loaded with battery electrochemically active components was designed to feed a vat photopolymerization (VPP) 3D printer. In direct alignment with NASA’s Artemis mission goals to develop sustainable lunar energy storage infrastructure necessary to support long-term human operations, TiO 2 was here selected as an active material for the negative electrode for sodium-ion and lithium-ion batteries due to its abundance on the lunar surface. The TiO 2 loading in the composite photocurable resin and in the resulting VPP-printed negative electrode was increased as high as possible to enhance the electrochemical performance, while simultaneously ensuring the printability and acceptable mechanical strength for sample handling. The effect of thermal post-processing on the electrical, electrochemical and mechanical performance is reported. Finally, a configurational study is implemented to identify the impact of two different electrode designs (cubic and gyroid lattice unit cells) on the electrochemical performance. This work addresses the difficulties related to the introduction of solid particles within a VPP photocurable resin and the need for a compromise between the electrochemical performances and printability to obtain fully functional VPP-printed electrodes.

sodium-ion battery↗
NASA NTRS1989

Near-field testing of the 15-meter hoop-column antenna

A 15-m-diameter antenna was tested to verify that dimensional tolerances for acceptable performance could be achieved and to verify structural, electromagnetic, and mechanical performance predictions. This antenna utilized the hoop column structure, a gold plated molybdenum mesh reflector, and 96 control cables to adjust the reflector conformance with a paraboloid. The dimensional conformance of the antenna structure and surface was measured with metric camera and theodolites. Near field pattern data were used to assess the electromagnetic performance at five frequencies from 2.225 to 11.6 GHz. The reflector surface was adjusted to greatly improve electromagnetic performance with a finite element model and the surface measurements. Measurement results show that antenna surface figure and adjustments and electromagnetic patterns agree well with predictions.

Schroeder, Lyle C.↗
NASA NTRS1992

Novel matrix resins for composites for aircraft primary structures, phase 1

The objective of the contract is the development of matrix resins with improved processability and properties for composites for primarily aircraft structures. To this end, several resins/systems were identified for subsonic and supersonic applications. For subsonic aircraft, a series of epoxy resins suitable for RTM and powder prepreg was shown to give composites with about 40 ksi compressive strength after impact (CAI) and 200 F/wet mechanical performance. For supersonic applications, a thermoplastic toughened cyanate prepreg system has demonstrated excellent resistance to heat aging at 360 F for 4000 hours, 40 ksi CAI and useful mechanical properties at greater than or equal to 310 F. An AB-BCB-maleimide resin was identified as a leading candidate for the HSCT. Composite panels fabricated by RTM show CAI of approximately 50 ksi, 350 F/wet performance and excellent retention of mechanical properties after aging at 400 F for 4000 hours.

Woo, Edmund P.↗
NASA NTRS2001

Phenylethynyl Terminated Arylene Ether Oxadiazole and Triazole Oligomers and Their Cured Polymers

Several novel phenylethynyl terminated arylene ether oligomers containing oxadiazole and triazole rings were prepared as part of an effort to develop high performance polymers with an attractive combination of properties (e.g. processability and mechanical performance) for future NASA applications. The oligomers displayed low melt viscosities and good solubilities. Thin films cast from solutions of the oligomers and cured for one hour at 350 C in air gave good tensile properties. Titanium to titanium (6Al-4V) tensile shear specimens were readily fabricated and provided moderate strengths. The chemistry and properties of these new materials are discussed.

Thompson, C. M.↗
NASA NTRS1972

Lubricant selection for gear designers

Guide for gear designers, consisting of theory, calculations, charts, curves and references, explains lubrication requirements for gears to insure maximum performance. Mechanical and service variables are considered in order to obtain optimum gear performance under severe operating conditions.

Townsend, D. P.↗
NASA NTRS1996

Brush Seals for Cryogenic Applications: Performance, Stage Effects, and Preliminary Wear Results in LN2 and LH2

Brush seals are compliant contacting seals and have significantly lower leakage than labyrinth seals in gas turbine applications. Their long life and low leakage make them candidates for use in rocket engine turbopumps. Brush seals, 50.8 mm (2 in.) in diameter with a nominal 127-micron (0.005-in.) radial interference, were tested in liquid nitrogen (LN2) and liquid hydrogen (LH2) at shaft speeds up to 35,000 and 65,000 rpm, respectively, and at pressure drops up to 1.21 MPa (175 psid) per brush. A labyrinth seal was also tested in liquid nitrogen to provide a baseline. The LN2 leakage rate of a single brush seal with an initial radial shaft interference of 127 micron (0.005 in.) measured one-half to one-third the leakage rate of a 12-tooth labyrinth seal with a radial clearance of 127 micron (0.005 in.). Two brushes spaced 7.21 micron (0.248 in.) apart leaked about one-half as much as a single brush, and two brushes tightly packed together leaked about three-fourths as much as a single brush. The maximum measured groove depth on the Inconel 718 rotor with a surface finish of 0.81 micron (32 microinch) was 25 micron (0.0010 in.) after 4.3 hr of shaft rotation in liquid nitrogen. The Haynes-25 bristles wore approximately 25 to 76 micron (0.001 to 0.003 in.) under the same conditions. Wear results in liquid hydrogen were significantly different. In liquid hydrogen the rotor did not wear, but the bristle material transferred onto the rotor and the initial 127 micron (0.005 in.) radial interference was consumed. Relatively high leakage rates were measured in liquid hydrogen. More testing is required to verify the leakage performance, to validate and calibrate analysis techniques, and to determine the wear mechanisms. Performance, staging effects, and preliminary wear results are presented.

Proctor, Margaret P.↗