SEARCH · Search NASA

Results for “membrane viscosity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

51 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Direct ink writing of shear exfoliated two-dimensional nanomaterial- elastomeric multifunctional nanocomposite

Direct ink writing (DIW) of polymer nanocomposites with high loadings of two-dimensional (2D) nanofillers (graphene and hexagonal boron nitride (hBN)) is challenging because of potential clogging, use of hazardous solvents, and agglomeration. Here, in this work, a shear exfoliation and sieving method to prepare DIW ink with high loading of nanofillers produced from low-cost bulk layered materials such as graphite and bulk hBN powder for successful DIW printing without the use of any solvents, binders, or plasticizers. The single-step exfoliation technique resulted in a composite with substantial layer reduction along the c-axis, as confirmed by SEM, TEM, XRD, and Raman analysis. Incorporating exfoliated graphene (40 wt%) increased viscosity by ∼6 orders of magnitude due to enhanced particle–matrix interactions, leading to pronounced yield stress behavior and a yield stress of approximately 1598 Pa, which enabled excellent shape retention during extrusion. Using the DIW technique, porous structures such as desalination membranes, self-sensing bone scaffolds, thermal management coating, and serpentine strain sensors were fabricated. When tested in a direct contact membrane distillation setup, the fabricated membrane demonstrated a promising permeate flux of 21.85 Lm −2 h −1 and a salt rejection of 74.3 %. The fabricated serpentine sensor exhibited stable signal variations under cyclic tensile loading, with a working range of 0–200 % strain and a maximum gauge factor of 43,735. A cell culture test using the printed bone scaffold demonstrated promising cell attachment and proliferation. The DIW printed hBN nanocomposite exhibited reversible shape change under heat, demonstrating potential 4D printing capability and efficient thermal management when exposed to high heat or flame.

Desalination↗

DOE OSTI2024

Amine functionalized supported ionic liquid membranes (SILMs) for CO 2 /N 2 separation

Supported ionic liquid membranes (SILMs), containing aprotic N-heterocyclic anion ionic liquids (AHA ILs) in an inorganic inert support, exhibit CO 2 /N 2 permselectivity values as high as 640 at 35.0 °C and 0.03 bar CO 2 , which represents conditions similar to post-combustion carbon capture (PCCC) from a natural gas power plant. A Fickian model fit to the experimental data estimates CO 2 permeability at direct air capture (DAC) conditions of 10,400 barrer and a CO 2 /N 2 permselectivity of 4000 for the best performing IL, triethyl(octyl)phosphonium 4-bromopyrazolide ([P 2228 ][4-BrPyra]). The most important criterion for high selectivity is a large equilibrium constant for binding between the IL and CO 2 , which results in high CO 2 solubility. ILs with smaller molar volumes and with no fluoroalkyl chains enhance N 2 rejection. As a result, low viscosity and high IL molar density also enhance CO 2 /N 2 permselectivity and CO 2 permeance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Random Walks and Sticky Surfaces: Single-Molecule Measurements of Solute Diffusion in Ethanol/Water-Filled Anodic Alumina Nanopores

Nanoporous anodic aluminum oxide (AAO) membranes are now being explored for use in advanced chemical separations, including in the dehydration of biofuels such as ethanol. Optimization of membrane performance requires an in-depth understanding of how solvent mixtures and solutes behave under nanoconfinement. In this work, the diffusion of rhodamine B (RhB) dye through 10 nm and 20 nm AAO nanopores filled with a series of ethanol/water mixtures (0 - 33% water) is explored by fluorescence correlation spectroscopy (FCS). RhB was found to diffuse through the pores by two distinct mechanisms with mean diffusion coefficients, $D_f$ and $D_s$, reflecting fast and slow diffusive motions, respectively, with values that differ by nearly two orders of magnitude. Further, both $D_f$ and $D_s$ increased with pore size and were significantly smaller than $D_b$, the RhB diffusion coefficient in bulk liquid. Mean $D_f$ values follow a composition-dependent trend that closely mimics the viscosity dependence of $D_b$. Additional slowing of fast RhB diffusion is attributed to both hydrodynamic drag and electrostatic interactions with the nanopore surface. The mean $D_s$ values exhibit a different trend with increasing water content, revealing an increase in $D_s$ and a decrease in the contributions of slow diffusion to the observed dynamics. The fluorescence time transient data used in the analysis show that the slow diffusion process is strongly hindered and likely involves frequent adsorption of RhB to the pore surfaces. These results provide new insights into the detailed molecular-level mechanisms of mass transport in nanoporous AAO membranes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Adsorption and Solvation Modulate Rhodamine B Diffusion in Ethanol/Water-Filled Anodic Alumina Nanopores

Confinement of solvents and solutes within nanoporous materials frequently leads to the emergence of unique mass transport behaviors that, once fully understood, may lead to improved chemical separations. Here, the diffusion of Rhodamine B (RhB) dye within 10 and 20 nm diameter anodic aluminum oxide (AAO) nanopores filled with binary ethanol/water mixtures is investigated. Mixture compositions spanning from pure ethanol to pure water are employed. The results of confocal fluorescence correlation spectroscopy studies reveal that RhB diffusion occurs by a two-component mechanism comprising composition-dependent fast and slow motions, characterized by diffusion coefficients D f and D s . The results are consistent with those of previous studies performed under more limited conditions [J. Phys. Chem. C, 2023, 127, 411-420]. The fast component scales with mixture viscosity and is assigned to hindered bulk-like diffusion in central pore regions. Slow diffusion likely involves adsorption of RhB to the pore surface and may be described by a desorption mediated mechanism. The occurrence of RhB adsorption to the AAO surface is verified at the single-molecule level by wide-field fluorescence imaging of membrane cross-sectional surfaces. Unique composition dependent trends in the autocorrelation amplitude and in D s that mimic bulk RhB solubility are revealed. D s is found to be smallest in pure ethanol and pure water and largest in intermediate mixtures. These results suggest that RhB surface adsorption is strongest in the pure liquids and weakest in mixtures of intermediate composition, where the dye is least soluble, and most soluble, respectively. As a result, molecular dynamics simulations reveal that a water layer appears on the pore surface under most conditions, while RhB is solvated primarily by ethanol. The composition dependence of RhB diffusion is concluded to reflect its solvation dependent interactions with the pore walls.

36 MATERIALS SCIENCE↗

NASA NTRS2026

Designing a Propylene-Glycol Coolant Servicer System for Gateway’s Internal Active Thermal Control System

A human spacecraft ATCS—especially one using single-phase coolant loops exposed to cabin atmospheric conditions—requires periodic degassing and refilling to support long-duration missions of 15 to 30 years. During initial fill operations, system maintenance, gas permeation, and quick-disconnect mating or de-mating, small amounts of gas can gradually enter the coolant system over time. This can lead to degraded heat transfer performance, pump cavitation, and potentially pump vapor lock if a significant gas volume accumulates over time. Additionally, system leaks and routine fluid sampling can gradually reduce accumulator volumes to unacceptable levels, requiring periodic refills. In more severe cases, catastrophic changes in fluid composition may necessitate emergency draining, refilling, and degassing to ensure continued system functionality. These risks were identified and mitigated on the ISS ITCS through the development of a dual-membrane degasser ORU and a Fluid Servicer System ORU for coolant refilling. These systems were developed for the fully water-based ISS ITCS Coolant[1]. The Gateway space station, the first permanent human habitat in lunar orbit, uses a propylene-glycol/water coolant mixture, which has significantly different fluid properties compared to pure water. Because microgravity degassing technologies are sensitive to fluid surface tension and viscosity, existing ISS hardware is not suitable for servicing a propylene-glycol-based TCS. Unlike the ISS, the Gateway will operate in a higher-radiation environment and must meet stricter mass constraints due to its location outside of low earth orbit. This Government Furnished Equipment (GFE) flight hardware project aims to develop a lightweight, radiation-resistant Coolant Servicer System (CSS) capable of degassing and refilling Gateway’s propylene-glycol water-based IATCS.

Propylene Glycol Water↗

NASA NTRS2026

Designing a Propylene-Glycol Coolant Servicer System for Gateway’s Internal Active Thermal Control System

Propylene Glycol Water↗

DOE OSTI2025

Supported ionic liquid membranes (SILMs) with exceptional selectivity and permeability for dilute CO 2 separations

Supported ionic liquid membranes (SILMs), containing phosphonium ionic liquids with aprotic N-heterocyclic anions (AHA ILs) in an inert inorganic support, were tested under both dry and humidified (40 % RH) mixed-gas conditions down to 420 ppm CO 2 in N 2 at 35 °C. In the dry case, the best performing IL, triethyl(octyl)phosphonium 4-bromopyrazolide ([P 2228 ][4-BrPyra]) exhibited mixed-gas CO 2 permeabilities and CO 2 /N 2 permeability selectivities as high as 26,800 barrer and 7,000, respectively. In the presence of humidity, the CO 2 permeability and CO 2 /N 2 selectivity increased to 49,100 barrer and 13,200, respectively, and these are the highest reported combination in the literature. Humidity amplifies CO 2 permeabilities and CO 2 /N 2 permeability selectivities through increases in CO 2 capacity due to bicarbonate formation and through faster mobility of the mobile carrier from decreased viscosity. Furthermore, N 2 permeability stayed roughly invariant in the presence of humidity, likely from competing effects of viscosity reduction and lower N 2 solubility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Dry electrodes with a printed cellulose–graphene ink for low-profile strain sensors in electromyography

Dihydrolevoglucosenone, commonly known as Cyrene, is a renewable and fully biodegradable cellulose-waste derived, environmentally friendly solvent, presenting a non-toxic alternative to N-methyl-2-pyrrolidone (NMP). Currently, solution-based processing of graphene and other similar van der Waals solids favor toxic solvents such as NMP, limiting their use for biosensing. However, with the use of Cyrene, bio-compatible printable devices are possible, and studies have already demonstrated its use in temperature and other biosensing methods through screen-printing. Screen-printing unfortunately often requires masks that constrain the minimum acquirable feature size to be above hundreds of centimeters and wastes material, adding to process complexity and cost. Conversely, inkjet-printing is an attractive alternative for the maskless patterning of hierarchically assembled structures, with micron length scales attainable. Graphene's high conductivity positions it ideally for long-wear sensors such as dry electrodes or respiration monitors. Here, we demonstrate the potential of Cyrene-based graphene inks through few-layer inkjet printing on flexible substrates for the first time, to produce non-toxic conductors toward a strain-mediated mechanism for biosensing, used to detect bodily motion for wearable electronics. The challenges overcome in this study include engineering ink chemistry and printing parameters such that Cyrene's relatively high viscosity compared to typical inkjet solvents, still allows for droplet ejection in a conventional material printer, yielding well-resolved clean line-edges in contrast to other solvents that exhibit diffuse line-edges possibly from stray droplets and ink-splashing. Temperature-dependent transport measurements on the inkjet-printed Cyrene-based graphene films showed the conductivity to be largely temperature-invariant but at lower temperatures below 100 K, conductivity decreased, likely as a result of increased inter-membrane separation arising from thermal contraction. Additionally, temperature-dependent Raman spectroscopy showed the red-shift in the G-band, 2D-band and D-band peaks, as temperature increased. As a result, by validating flexion motion detection of the proximal interphalangeal joint demonstrated in this study, our work is the first of its kind to successfully additively manufacture inkjet-printed Cyrene-based graphene strain sensors on flexible substrates for bio-sensing and wearables.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Effect of Dispersion Medium Composition and Ionomer Concentration on the Microstructure and Rheology of Fe–N–C Platinum Group Metal-free Catalyst Inks for Polymer Electrolyte Membrane Fuel Cells

In this paper, we present an investigation of the microstructure and rheological behavior of catalyst inks consisting of Fe–N–C platinum group metal-free catalysts and a perfluorosulfonic acid ionomer in a dispersion medium (DM) of water and 1-propanol ( n PA). The effects of the ionomer-to-catalyst (I/C) ratio and weight percentage of water (H 2 O %) in the DM on the ink microstructure were studied. Steady-shear and dynamic-oscillatory-shear rheology, in combination with synchrotron X-ray scattering, was utilized to understand interparticle interactions and the level of agglomeration of the inks. In the absence of the ionomer, the inks were significantly agglomerated, approaching a gel-like microstructure for catalyst concentrations as low as 2 wt %. The effect of H 2 O % in the DM on particle agglomeration was found to vary with particle concentration. In concentrated inks (≥2 wt % catalyst), increasing H 2 O % was found to increase agglomeration because of the hydrophobic nature of the catalysts. In dilute inks (<1 wt % catalyst), the trend was reversed with increasing H 2 O %, suggesting that electrostatic interactions are dominating the behavior. In inks with 5 wt % catalyst, the addition of an ionomer was found to significantly stabilize the catalyst against agglomeration. Maximum stability was observed at 0.35 I/C for all DM H 2 O % studied. At high ionomer concentrations (I/C > 0.35), interesting differences were observed between n PA-rich inks (H 2 O % ≤ 50%) and H 2 O-rich (82% H 2 O) inks. The n PA-rich inks remained predominantly stable—ink viscosity only weakly increased with I/C and the Newtonian behavior was maintained for I/C up to 0.9. In contrast, the H 2 O-rich inks exhibited a significant increase in viscoelasticity with increasing I/C, suggesting flocculation of the catalyst by the ionomer. These differences suggest that the nature of the interactions between the ionomer and catalyst is highly dependent on the H 2 O % in the DM.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Slot-die-coating operability windows for polymer electrolyte membrane fuel cell cathode catalyst layers

Roll-to-roll (R2R) slot-die coating of polymer electrolyte membrane fuel cell (PEMFC) catalyst layers represents a scalable deposition method for producing 10–20 m 2 ·min -1 of catalyst-coated gas diffusion layers (GDLs). This high-throughput production technique will help lower the cost of PEMFC catalyst layers. The uniformity of the wet layer applied by slot die deposition is affected by process parameters such as substrate speed, vacuum pressure applied at the upstream meniscus, gap between the slot die lips and substrate, ink rheology, and other ink and substrate properties. The set of conditions for producing a defect-free coating with a dilute ink typically requires little to no upstream vacuum pressure, so suitable operating conditions can be found easily through trial and error and operator intuition. However, the higher viscosity of more concentrated inks dramatically shifts the range of settings that result in a homogeneous coating to higher vacuum levels, which are harder to find through hit or miss. A predictive model showing the range of operable conditions decreases material wastage inherent in experimentally searching for suitable parameters. In this study, the defect-free coating parameter window is explored experimentally and theoretically for two concentrations of PEFC cathode inks. Both a full capillary hydrodynamic model and a computationally cheaper viscocapillary model successfully predict the experimentally determined coating window within the experimental and model uncertainty limits for inks with 5.3 wt% and 12.0 wt% solids ink while maintaining the 0.1 mg Pt ·cm -2 Pt areal loading target. Here, this paper demonstrates a viable pathway for meeting the $30/kW net ultimate cost target of the United States Department of Energy (U.S. DOE) Hydrogen Fuel Cells Technologies Office (HFTO). The concentrated ink lowers the thermal energy and capital expenditure (CapEx) budget of the coating process by decreasing the amount of time, energy, and floorspace required for drying the coating.

25 ENERGY STORAGE↗

DOE OSTI2021

Toward Optimizing Electrospun Nanofiber Fuel Cell Catalyst Layers: Polymer–Particle Interactions and Spinnability

We investigate the effect of the poly(acrylic acid) (PAA) carrier polymer concentration on the microstructure and rheological properties of catalyst inks for electrospun polymer–electrolyte membrane fuel-cell catalyst layers. Characterization of an ink microstructure using oscillatory shear rheology showed that the catalyst particles (platinum on carbon) are significantly agglomerated in the absence of PAA or an ionomer. Both the ionomer and PAA promoted the stability of the particles against agglomeration via electrosteric stabilization by adsorbing onto the particle surface. Increasing the PAA concentration increased the stability of the particles (or reduced the agglomerated structure) due to increasing PAA coverage onto the free surface area of the particles. However, beyond a certain increase in concentration, PAA was found to predominantly remain as an excess free polymer in the ink due to an insufficient free/available surface area on the particles for further PAA coverage. Extensional rheology measurements demonstrated that PAA enhances the extensional viscosities of the inks. Consequently, increasing the PAA concentration in the ink promoted the evolution of uniform nanofibers. However, beyond a certain concentration, a significant increase in the shear viscosities of the inks led to defective fiber morphologies because of the onset of flow instabilities. Electrochemical performance comparisons between catalyst layers with different PAA concentrations showed maximum performance at the PAA concentration that led to the least agglomerated structure of the catalyst, most uniform fiber morphologies, and low concentrations of free (non-adsorbing) PAA in the electrode. These results provide a rationale for optimization of electrospun catalyst nanofibers for both spinnability and electrochemical performance.

25 ENERGY STORAGE↗

DOE OSTI2022

Surface fluctuating hydrodynamics methods for the drift-diffusion dynamics of particles and microstructures within curved fluid interfaces

Here we introduce fluctuating hydrodynamics approaches on surfaces for capturing the drift-diffusion dynamics of particles and microstructures immersed within curved fluid interfaces of spherical shape. We take into account the interfacial hydrodynamic coupling, traction coupling with the surrounding bulk fluid, and thermal fluctuations. For fluid-structure interactions, we introduce Immersed Boundary Methods (IBM) and related Stochastic Eulerian-Lagrangian Methods (SELM) for curved surfaces. We use these approaches to investigate the statistics of surface fluctuating hydrodynamics and microstructures. For velocity autocorrelations, we find characteristic power-law scalings $τ^{-1}, τ^{-2}$, and plateaus can emerge. This depends on the physical regime associated with the geometry, surface viscosity, and bulk viscosity. This differs from the characteristic $τ^{-3/2}$ scaling for bulk three dimensional fluids. We develop theory explaining these observed power-laws associated with time-scales for dissipation within the fluid interface and coupling to the surrounding fluid. We then use our introduced methods to investigate a few example systems and roles of hydrodynamic coupling and thermal fluctuations including for the kinetics of passive particles and active microswimmers in curved fluid interfaces.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2021

Incorporation and Assembly of a Light-Emitting Enzymatic Reaction into Model Protein Condensates

Eukaryotic cells partition enzymes and other cellular components into distinct subcellular compartments to generate specialized biochemical niches. A subclass of these compartments form in the absence of lipid membranes, via liquid-liquid phase separation of proteins to form biomolecular condensates or “membraneless organelles” such as nucleoli, stress granules, and P-bodies. Because of their ability to form compartments from simple starting materials, membraneless organelles are an attractive target for engineering new functionalities in both living cells and protocells. In this work, we demonstrate incorporation of novel enzymatic activity in protein coacervates with a light-generating enzyme, NanoLuc, to produce bioluminescence. Using condensates comprised of the disordered RGG domain of C. elegans LAF-1, we show functionalization of condensates with enzymatic activity in vitro and that localization to protein coacervates enhances the assembly and activity of split enzymes. To build condensates that function as light emitting reactors, we designed a NanoLuc enzyme flanked by RGG domains. Furthermore, the resulting condensates concentrated NanoLuc by 10-fold over bulk solution and display significantly increased net reaction rates. We further show that condensate viscosity impacts light emission due to diffusion-limited behavior. By splitting NanoLuc enzyme into its constituent components, we demonstrate that NanoLuc activity can be reconstituted via co-condensation. Further, we demonstrate control of the spatial localization of enzyme within condensates by targettng NanoLuc to the surface of in vitro condensates. Collectively, this work demonstrates that membraneless organelles can be endowed with localized enzymatic activity, and that this activity can be spatially and temporally controlled via enzyme reconstitution and design of protein surfactants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Determining the impacts of venoarterial extracorporeal membrane oxygenation on cerebral oxygenation using a one-dimensional blood flow simulator

Venoarterial extracorporeal membrane oxygenation (VA-ECMO) is a mechanical system that provides rapid and short-term support for patients with cardiac failure. In many patients, pulmonary function is also impaired, resulting in poorly-oxygenated cardiac outflow competing against well-oxygenated VA-ECMO outflow, a condition known as North-South syndrome. North-South syndrome is a primary concern because of its potential to cause cerebral hypoxia, which has a critical influence on neurological complications often seen in this patient population. In order to reduce ischemic neurological complications, it is important to understand how clinical decisions regarding VA-ECMO parameters influence blood oxygenation. In our work, we studied the impacts of flow rate and cannulation site on oxygenation using a one-dimensional (1D) model to simulate blood flow. Our model was initially tested by comparing blood flow results to those observed from experimental work in VA-ECMO patients. The 1D model was combined with a two-phase flow model to simulate oxygenation. Additionally, the influence of various other clinician-tunable parameters on oxygenation in the common carotid arteries (CCAs) were tested, including, blood viscosity, cannula position within the insertion artery, heart rate, and systemic vascular resistance (SVR), as well as geometrical changes such as arterial radius and length. Our results indicated that blood oxygenation to the brain strongly depended on the cannula insertion site and the VA-ECMO flow rate with a weaker but potentially significant dependence on arterial radius. During femoral cannulation, VA-ECMO flow rates greater than ~4.9 L/min were needed to perfuse the CCAs. However, axillary and central cannulation began to perfuse the CCAs at significantly lower flow (~1 L/min). These results may help explain the incidence of cerebral hypoxia in this patient population and the common need to change cannulation strategies during treatment to address this clinical problem. While this work describes patient-averaged results, determining these relationships between VA-ECMO parameters and cerebral hypoxia is an important step towards future work to develop patient-specific models that clinicians can use to improve outcomes.

1D blood flow↗

DOE OSTI2023

Bead–Spring Simulation of Ionomer Melts—Studying the Effects of Chain-Length and Associating Group Fraction on Equilibrium Structure and Extensional Flow Behavior

Ionomers are associative polymers with diverse applications ranging from selective membranes and high-performance adhesives to abrasion- and chemical-resistant coatings, insulation layers, vacuum packaging, and foamed sheets. Within equilibrium melt, the ionic or associating groups are known to form thermally reversible, associative clusters whose presence can significantly affect the system’s mechanical, viscoelastic, and transport properties. It is, thus, of great interest to understand how to control such clusters’ size distribution, shape, and stability through the designed choice of polymer architecture and the ionic groups’ fraction, arrangement, and interaction strength. In this work, we represent linear associating polymers using a Kremer–Grest type bead–spring model and perform large-scale MD simulations to explore the effect of polymer chain-length (l) and fraction (f s ) of randomly placed associating groups on the size distribution and stability of formed clusters. We consider different chain-lengths (below and above entanglement), varying fractions of associating groups (represented by ‘sticky’ beads) between 5 and 20%, and a fixed sticky–sticky nonbond interaction strength of four times that between regular non-associating beads. For all melts containing associating groups the equilibrium structure factor S(q) displays a signature ionomer peak at low wave vector q whose intensity increases with increasing f s and l. The average cluster size Nc increases with f s . However, the effect of chain-length on Nc appears to be pronounced only at higher values of f s . Under extensional flows, the computed stress (and viscosity) is higher at higher f s and l regardless of strain rate. Beyond a critical strain rate, we observe fragmentation of the associative clusters, which has interesting effects on the stress/viscous response.

36 MATERIALS SCIENCE↗