SEARCH · Search NASA

Results for “mesoscale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Slow Wake Recovery and Low Turbulence Behind Wind Farms Parameterized in Mesoscale Simulations

Numerical weather prediction (NWP) and climate models equipped with wind-farm parameterizations (WFPs) can simulate cluster wake effects affecting downstream wind farms in both onshore and offshore environments. This study evaluates wake recovery behind a wind farm represented by the NWP-WFP approach in the Weather Research and Forecasting (WRF) model using either the Fitch et al. (2012) or Ma et al. (2022a, b) WFPs. Results are benchmarked against large-eddy simulations (LES) of an idealized offshore wind farm with aligned and staggered layouts under neutral atmospheric stability. Near-farm wake recovery is underestimated in NWP-WFP simulations due to its representation on a coarse mesoscale grid. This limitation leads to slow wake recovery through two interconnected mechanisms: (i) spatial gradients in the wind velocity field are weaker compared to LES and (ii) turbulence kinetic energy (TKE) remains low not because of excessive dissipation but due to insufficient shear production caused by these weakened gradients. For the scenario considered here, a wind-speed bias develops in the near-farm wake and persists into the far wake. Differences between the NWP-WFP simulations and LES emerge within a short distance downstream of the farm exit, where the mesoscale simulations recover too slowly. This reduced recovery contributes approximately 0.15-0.50 m s-1 to the near-farm wind-speed bias. The bias established in this region is not subsequently compensated for downstream but instead propagates into the far wake, where wind-speed differences of approximately 0.4-0.6 m s-1 remain up to 50 km downstream. Higher-resolution mesoscale simulations partially reduce this bias. Increasing turbine-added TKE or including subgrid wake effects provides additional improvement, but neither fully addresses the underlying cause. The slow wake recovery is not caused by limitations of the WFPs themselves, as it also occurs outside their region of influence, and adding subgrid wake effects does not significantly impact recovery. Rather, the slow wake recovery is a consequence of mesoscale flow representation. This behavior is not limited to regions downstream of the wind farm but is less visible within the farm, where wake recovery occurs simultaneously with turbine-induced momentum extraction. These results highlight the need for improved representations of wake recovery both within and downstream of wind farms. While enhanced subgrid modeling, shear-driven TKE production, and refined WFP formulations may improve intra-farm dynamics, accurately capturing near-farm wake recovery downstream remains challenging, as WFPs do not act in this region.

17 WIND ENERGY↗

NASA NTRS1976

Interactive applications of satellite observations and mesoscale numerical models

The impact of numerical weather prediction (NWP) and satellite meteorology on operational weather forecasting has become overwhelming in the past few years. The paper looks toward the merger of these technologies in making short range 6-18 h forecasts through the use of mesoscale NWP models. A short-range (2-18 h) mesoscale forecast system envisioned for the near future is described that includes four components: hydrodynamic numerical models, large-scale and mesoscale; satellites, polar orbiting for high latitudes and geostationary for low latitudes; mesoclimatology, derived in large part from satellite data; and special-purpose simple models and empirical relations. It is important that the components of the forecast system be developed in parallel rather than in series if the system is to be completed within five years. There is enough evidence to substantiate the revolution in the mesoscale weather prediction in the next five years.

Kreitzberg, C. W.↗

NASA NTRS1981

A mesoscale sixth-order numerical modelling system

A numerical simulation system is currently under development for NASA which is intended to improve the modeling of subsynoptic and mesoscale adjustments associated with cyclogenesis, severe storm development and atmospheric transport processes. The model utilizes a standard hydrostatic sigma-p coordinate primitive equation set, with x,y-space differencing accurate to eighth order. A three-step dynamic initialization procedure is employed between the analysis of real-time data and grid interpolation. Results of an 18-hour simulation during which synoptic scale cyclogenesis, subsynoptic scale jet streak adjustments, mesoscale convergence zones and tornadic storms were observed have shown the present model to have the potential for simulating the fine-scale structure of features associated with cyclogenesis and intense squall-line development. The mesoscale model was also found to produce less truncation than the NWS LFM model, although a frictionless version of the mesoscale model somewhat overdeepens and overaccelerates features.

Kaplan, M. L.↗

NASA NTRS1984

The mesoscale stability of entrainment into cloud-topped mixed layers

The Lilly-type models for stratocumulus-capped mixed layers are shown to allow for a mesoscale instability in which mesoscale fluctuations of buoyancy and humidity are reinforced in phase by entrainment. In a model of an AMTEX mixed layer, this mesoscale instability has a maximum growth rate of about 0.00002 per sec at wavelengths 30 times the depth of the mixed layer. The instability is able to account for the existence and broad scale of the stratiform cloud patterns known as mesoscale cellular convection.

Fiedler, B. H.↗

NASA NTRS1985

Use of observational and model-derived fields and regime model output statistics in mesoscale forecasting

Various empirical and statistical weather-forecasting studies which utilize stratification by weather regime are described. Objective classification was used to determine weather regime in some studies. In other cases the weather pattern was determined on the basis of a parameter representing the physical and dynamical processes relevant to the anticipated mesoscale phenomena, such as low level moisture convergence and convective precipitation, or the Froude number and the occurrence of cold-air damming. For mesoscale phenomena already in existence, new forecasting techniques were developed. The use of cloud models in operational forecasting is discussed. Models to calculate the spatial scales of forcings and resultant response for mesoscale systems are presented. The use of these models to represent the climatologically most prevalent systems, and to perform case-by-case simulations is reviewed. Operational implementation of mesoscale data into weather forecasts, using both actual simulation output and method-output statistics is discussed.

Forbes, G. S.↗

NASA NTRS1985

Simulation of mesoscale convective response

Results are reported from a transfer of thermodynamic and dynamic data downscale from a two-dimensional mesoscale model to a two-dimensional cloud model and a subsequent examination of the differential convective response of the cloud model to a mesoscale structure. The mesoscale model included a high resolution PBL formulation, with convective forces expressed in a profile of exchange coefficients over the height of the PBL and the magnitude of the surface heat flux. Account was also taken of forcing by long- and short-wave radiation, surface forcing by the surface energy budget, the terrain shape, and possible wave reflection at the top boundary. The slab-symmetric cloud model possessed subgrid-scale features, five types of moisture terms, and a subroutine for accretion processes. The mesoscale environment was observed to have a significant impact on convective response, i.e., the vertical velocity and the cloud water. Various factors which were not included in the study and which must be considered are discussed.

Mcnider, R. T.↗

NASA NTRS1986

Initialization of a mesoscale model with satellite derived temperature profiles

The abilities of rawinsonde data and Tiros-N satellite derived temperature profile data to depict mesoscale precipitation accumulation are evaluated. Four mesoscale simulations using combinations of temperature, low-level wind, and low-level wind initialization were performed with the limited area mesoscale prediction system (LAMPS) model. Comparisons of the simulations with operational LFM forecast accumulations reveal that the LAMPS model simulations provide a better depiction of the observed precipitation accumulation than the LFM forecasts, and the satellite temperature profiles produce better mesoscale precipitation accumulation forecasts than the rawinsonde temperature data.

Kalb, Michael W.↗

NASA NTRS1987

Short range forecasting of sea breeze generated thunderstorms at the Kennedy Space Center: A real-time experiment using a primitive equation mesoscale numerical model

The operational efficiency of using guidance from a mesoscale numerical model to improve sea breeze thunderstorm forecasts at and around the Shuttle landing strip was assessed. The Prognostic Three-Dimensional Mesoscale (P3DM) model, developed as a sea breeze model, reveals a strong correlation between regions of mesoscale convergence and the triggering of sea breeze convection thunderstorms. The P3DM was modified to generate stability parameters familiar to the operational forecaster. In addition to the mesoscale fields of wind, vertical motion, moisture, temperature, a stability indicator, a combination of model-predicted K and Lifted Indices and the maximum grid cell vertical motion, were proposed and tested. Results of blind tests indicate that a forecaster, provided with guidance derived from model output, could improve local thunderstorm forecasts.

Lyons, Walter A.↗

NASA NTRS1988

Diabatic initialization for a mesoscale model simulation experiment

A mesoscale model simulation of a 'surrogate' atmosphere designed for the evaluation of adiabatic initialization and moisture enhancement techniques is briefly described. The simulation provides mesoscale precipitation rates and associated diabatic heating fields which are known exactly and are internally consistent within the context of the model. The advantage of this approach is that a numerical model can easily serve as a source of mesoscale data in the usual absence of internally consistent mesoscale observed data sets.

Kalb, Michael W.↗

NASA NTRS1988

Use of VAS data to diagnose the mesoscale environment of convective storms

The utility of VISSR Atmospheric Sounder (VAS) retrieval datasets for mesoscale analysis is explored. A detailed mesoscale air mass analysis method is presented in which VAS soundings, satellite imagery, and conventional surface data are used to diagnose mesoscale differences in air mass character. Comparisons are made with radiosonde observations of the same air mass differences. A mesoscale air mass analysis is presented with a discussion of the role that the various air masses play in subsequent convective development. In a second technique, several VAS-derived thermodynamic parameters, such as positive and negative buoyant energy, are shown to be well suited to operational forecasting of convective storm development and evolution. The derivation of these parameters and their applications in forecasting are illustrated.

Zehr, Raymond M.↗

NASA NTRS1993

Mesoscale disturbances in the tropical stratosphere excited by convection - Observations and effects on the stratospheric momentum budget

Aircraft temperature and pressure measurements as well as satellite imagery are used to establish the amplitudes and the space and time scale of potential temperature disturbances over convective systems. A conceptual model is proposed for the generation of mesoscale gravity waves by convection. The momentum forcing that a reasonable distribution of convection might exert on the tropical stratosphere through convectively excited mesoscale gravity waves of the observed amplitudes is estimated. Aircraft measurements show that presence of mesoscale disturbances in the lower stratospheric temperature, disturbances that appear to be associated with underlying convection. If the disturbances are convectively excited mesoscale gravity waves, their amplitude is sufficient that their breakdown in the upper stratosphere will exert a zonal force comparable to but probably smaller than the planetary-scale Kelvin waves.

Pfister, Leonhard↗

NASA NTRS1993

Examples of data assimilation in mesoscale models

The keynote address was the problem of physical initialization of mesoscale models. The classic purpose of physical or diabatic initialization is to reduce or eliminate the spin-up error caused by the lack, at the initial time, of the fully developed vertical circulations required to support regions of large rainfall rates. However, even if a model has no spin-up problem, imposition of observed moisture and heating rate information during assimilation can improve quantitative precipitation forecasts, especially early in the forecast. The two key issues in physical initialization are the choice of assimilating technique and sources of hydrologic/hydrometeor data. Another example of data assimilation in mesoscale models was presented in a series of meso-beta scale model experiments with and 11 km version of the MASS model designed to investigate the sensitivity of convective initiation forced by thermally direct circulations resulting from differential surface heating to four dimensional assimilation of surface and radar data. The results of these simulations underscore the need to accurately initialize and simulate grid and sub-grid scale clouds in meso- beta scale models. The status of the application of the CSU-RAMS mesoscale model by the NOAA Forecast Systems Lab for producing real-time forecasts with 10-60 km mesh resolutions over (4000 km)(exp 2) domains for use by the aviation community was reported. Either MAPS or LAPS model data are used to initialize the RAMS model on a 12-h cycle. The use of MAPS (Mesoscale Analysis and Prediction System) model was discussed. Also discussed was the mesobeta-scale data assimilation using a triply-nested nonhydrostatic version of the MM5 model.

Carr, Fred↗

NASA NTRS1994

Mesoscale roughness of Venus

The global distribution of multi-kilometer (approx. 9 km) length scale 'roughness' (hereafter mesoscale roughness or MR) on Venus can be estimated from the Magellan global altimetry dataset (GxDR) and then compared with MR data derived for Earth from 5' ETOP5 data and for Mars (from USGS Mars DTM dataset). The mesoscale roughness parameter (MR) represents the RMS variance in meters of the actual planetary surface topography relative to the best fitting tangent plane defined on the basis of a 3x3 pixel sliding window. The best-fit plane was computed using a least-squares solution which minimizes delta H, the sum of the squares of the differences between the 9 local elevation values (H(sub i)), and the elevation of best-fit plane at the same grid location. Using the best-fit plane and delta H, we have computed the RMS 'roughness' var(delta R), where this parameter is always minimized on the basis of its calculation using least squares. We have called this 'ruggedness' parameter the Mesoscale Roughness (MR) because it is directly related to the high-frequency variance of topography after mesoscale slopes and tilts (i.e., for Venus, the baseline over which MR is computed (dx) is approx. 8.8 km and dx for Earth is approx. 9.3 km) are removed. As such, MR represents the degree to which a planetary surface is more rugged than approximately 10 km scale facets or tilts. It should not be confused with the radar 'RMS Roughness' parameter computed at 0.1 to 10 m length scales on the basis of the Magellan radar altimeter echo. We will use our MR parameter to investigate the global ruggedness properties of Venus as they relate to geological provinces and in comparison with the spatial pattern of MR for Earth and Mars.

Garvin, J. B.↗

NASA NTRS1996

Workstation-Based Real-Time Mesoscale Modeling Designed for Weather Support to Operations at the Kennedy Space Center and Cape Canaveral Air Station

This paper describes the capabilities and operational utility of a version of the Mesoscale Atmospheric Simulation System (MASS) that has been developed to support operational weather forecasting at the Kennedy Space Center (KSC) and Cape Canaveral Air Station (CCAS). The implementation of local, mesoscale modeling systems at KSC/CCAS is designed to provide detailed short-range (less than 24 h) forecasts of winds, clouds, and hazardous weather such as thunderstorms. Short-range forecasting is a challenge for daily operations, and manned and unmanned launches since KSC/CCAS is located in central Florida where the weather during the warm season is dominated by mesoscale circulations like the sea breeze. For this application, MASS has been modified to run on a Stardent 3000 workstation. Workstation-based, real-time numerical modeling requires a compromise between the requirement to run the system fast enough so that the output can be used before expiration balanced against the desire to improve the simulations by increasing resolution and using more detailed physical parameterizations. It is now feasible to run high-resolution mesoscale models such as MASS on local workstations to provide timely forecasts at a fraction of the cost required to run these models on mainframe supercomputers. MASS has been running in the Applied Meteorology Unit (AMU) at KSC/CCAS since January 1994 for the purpose of system evaluation. In March 1995, the AMU began sending real-time MASS output to the forecasters and meteorologists at CCAS, Spaceflight Meteorology Group (Johnson Space Center, Houston, Texas), and the National Weather Service (Melbourne, Florida). However, MASS is not yet an operational system. The final decision whether to transition MASS for operational use will depend on a combination of forecaster feedback, the AMU's final evaluation results, and the life-cycle costs of the operational system.

Manobianco, John↗

NASA NTRS2002

The Impact of TRMM Data on Numerical Forecast of Mesoscale Systems

The impact of surface rainfall data derived from the TRMM Microwave Image (TMI) on the numerical forecast of mesoscale systems is evaluated. A series of numerical experiments are performed that assimilate TMI rainfall data into the Penn State University/National Centers for Atmospheric Research (PSU/NCAR) Mesoscale Model version 5 (MM5) using a four-dimensional variational data assimilation (4DVAR) technique. Experiments are conducted incorporating TMI rainfall data into the mesoscale model to improve hurricane initialization. It is found that assimilation of rainfall data into the model is beneficial in producing a more realistic eye and rain bands and also helps to improve the intensity forecast for the hurricane. Further 4DVAR experiments are performed on mesoscale convective systems (MCSs). Detailed results and related issues will be presented during the conference.

Pu, Zhao-Xia↗

NASA NTRS2003

Diabatic Initialization of Mesoscale Models in the Southeastern United States: Can 0 to 12h Warm Season QPF be Improved?

It is well known that numerical warm season quantitative precipitation forecasts lack significant skill for numerous reasons. Some are related to the model--it may lack physical processes required to realistically simulate convection or the numerical algorithms and dynamics employed may not be adequate. Others are related to initialization-mesoscale features play an important role in convective initialization and atmospheric observation systems are incapable of properly depicting the three-dimensional stability structure at the mesoscale. The purpose of this study is to determine if a mesoscale model initialized with a diabatic initialization scheme can improve short-term (0 to 12h) warm season quantitative precipitation forecasts in the Southeastern United States. The Local Analysis and Prediction System (LAPS) developed at the Forecast System Laboratory is used to diabatically initialize the Pennsylvania State University/National center for Atmospheric Research (PSUNCAR) Mesoscale Model version 5 (MM5). The SPORT Center runs LAPS operationally on an hourly cycle to produce analyses on a 15 km covering the eastern 2/3 of the United States. The 20 km National Centers for Environmental Prediction (NCEP) Rapid Update Cycle analyses are used for the background fields. Standard observational data are acquired from MADIS with GOES/CRAFT Nexrad data acquired from in-house feeds. The MM5 is configured on a 140 x 140 12 km grid centered on Huntsville Alabama. Preliminary results indicate that MM5 runs initialized with LAPS produce improved 6 and 12h QPF threat scores compared with those initialized with the NCEP RUC.

Lapenta, William M.↗

NASA NTRS2004

GMS-based"Future Time" Rainfall Data Assimilation for Mesoscale Weather Prediction over Korean Peninsula and Future Prospects with GPM Satellite Measurements

This study examines the use of satellite-derived nowcasted (short-term forecasted) rainfall over 3-hour time periods to gain an equivalent time increment in initializing a nonhydrostatic mesoscale model used for predicting convective rainfall events over the Korean peninsula. Infrared (IR) window measurements from the Japanese Geostationary Meteorological Satellite (GMS) are used to specify latent heating for a spinup period of the model - but in future time -- thus initializing in advance of actual time in the framework of a prediction scenario. The main scientific objective of the study is to investigate the strengths and weaknesses of this approach insofar as data assimilation, in which the nowcasted assimilation data are derived independently of the prognostic model itself. Although there have been various recent improvements in formulating the dynamics, thermodynamics, and microphysics of mesoscale models, as well as computer advances which allow the use of high resolution cloud-resolving grids and explicit latent heating over regional domains, spinup remains at the forefront of unresolved mesoscale modeling problems. In general, non-realistic spinup limits the skill in predicting the spatial-temporal distribution of convection and precipitation, primarily in the early hours of a. forecast, stemming from standard prognostic variables not representing the initial diabatic heating field produced by the ambient convection and cloud fields. The long-term goal of this research is to improve short-range (12-hour) quantitative precipitation forecasting (QPF) over the Korean peninsula through the use of innovative data assimilation methods based on geosynchronous satellite measurements. As a step in th~s direction, a non-standard data assimilation experiment in conjunction with GMS-retrieved nowcasted rainfall information introduced to the mesoscale model is conducted. The 3-hourly precipitation forecast information is assimilated through nudging the associated diabatic heating during the early stages of a forecast period. This procedure is expected to enhance details in the moisture field during model integration, and thus improve spinup performance, assuming the errors in the future time latent heating data ate less than intrinsic model background errors.

Smith, Eric A.↗

NASA NTRS2007

The Impact of Microphysics on Intensity and Structure of Hurricanes and Mesoscale Convective Systems

During the past decade, both research and operational numerical weather prediction models, e.g. Weather Research and Forecast (WRF) model, have started using more complex microphysical schemes originally developed for high-resolution cloud resolving models (CRMs) with a 1-2 km or less horizontal resolutions. WRF is a next-generation mesoscale forecast model and assimilation system that has incorporated modern software framework, advanced dynamics, numeric and data assimilation techniques, a multiple moveable nesting capability, and improved physical packages. WRF model can be used for a wide range of applications, from idealized research to operational forecasting, with an emphasis on horizontal grid sizes in the range of 1-10 km. The current WRF includes several different microphysics options such as Purdue Lin et al. (1983), WSM 6-class and Thompson microphysics schemes. We have recently implemented three sophisticated cloud microphysics schemes into WRF. The cloud microphysics schemes have been extensively tested and applied for different mesoscale systems in different geographical locations. The performances of these schemes have been compared to those from other WRF microphysics options. We are performing sensitivity tests in using WRF to examine the impact of six different cloud microphysical schemes on precipitation processes associated hurricanes and mesoscale convective systems developed at different geographic locations [Oklahoma (IHOP), Louisiana (Hurricane Katrina), Canada (C3VP - snow events), Washington (fire storm), India (Monsoon), Taiwan (TiMREX - terrain)]. We will determine the microphysical schemes for good simulated convective systems in these geographic locations. We are also performing the inline tracer calculation to comprehend the physical processes (i.e., boundary layer and each quadrant in the boundary layer) related to the development and structure of hurricanes and mesoscale convective systems.

Tao, Wei-Kuo↗