Search NASA⌕ Search

SEARCH · Search NASA

Results for “metallography”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Interface stability of ultrasonic additively manufactured Zircaloy-4 during hydrothermal corrosion

Simulated pressurized water reactor conditions (330 °C, 15.6 MPa, ~20 ppb oxygen) without irradiation were used to investigate the hydrothermal corrosion behavior of ultrasonic additively manufactured Zircaloy-4 up to 1000 h. X-ray computed tomography allowed for visualization of defects from processing and their progression after corrosion experiments. The specimens were found to have clear variability in the mass change data, compared to typical wrought Zircaloy-4 specimens. The variation in the mass change after exposure was attributed to weld defects connected to the specimen surface which allowed ingress of oxidant into the samples. Defects visualized by computed tomography were found via metallography and characterized. In conclusion, ultrasonic additively manufactured Zircaloy-4 was found to have comparable corrosion behavior as wrought Zircaloy-4 for specimens which did not have clear surface defects along weld interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ synchrotron diffraction and modeling of non-equilibrium solidification of a MnFeCoNiCu alloy

The solidification mechanism and segregation behavior of laser-melted Mn 35 Fe 5 Co 20 Ni 20 Cu 20 was firstly investigated via in situ synchrotron x-ray diffraction at millisecond temporal resolution. The transient composition evolution of the random solid solution during sequential solidification of dendritic and interdendritic regions complicates the analysis of synchrotron diffraction data via any single conventional tool, such as Rietveld refinement. Therefore, a novel approach combining a hard-sphere approximation model, thermodynamic simulation, thermal expansion measurement and microstructural characterization was developed to assist in a fundamental understanding of the evolution of local composition, lattice parameter, and dendrite volume fraction corresponding to the diffraction data. This methodology yields self-consistent results across different methods. Via this approach, four distinct stages were identified, including: (I) FCC dendrite solidification, (II) solidification of FCC interdendritic region, (III) solid-state interdiffusion and (IV) final cooling with marginal diffusion. It was found out that in Stage I, Cu and Mn were rejected into liquid as Mn 35 Fe 5 Co 20 Ni 20 Cu 20 solidified dendritically. During Stage II, the lattice parameter disparity between dendrite and interdendritic region escalated as Cu and Mn continued segregating into the interdendritic region. After complete solidification, during Stage III, the lattice parameter disparity gradually decreases, demonstrating a degree of composition homogenization. The volume fraction of dendrites slightly grew from 58.3 to 65.5%, based on the evolving composition profile across a dendrite/interdendritic interface in diffusion calculations. Postmortem metallography further confirmed that dendrites have a volume fraction of 64.7 ± 5.3% in the final microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2025

FAST Irradiations, Postirradiation Examinations, and Modeling of U-Mo for Light Water Reactor Applications

Many next generation light water reactor (LWR) concepts, such as mobile small modular reactors, are seeking to use smaller core dimensions than conventional reactor types. Smaller reactor cores require an increase in fissile material to maintain reactivity. For non-proliferation purposes, enrichment increases are limited to less than 20% (high assay low enriched uranium, [HALEU]) and so higher uranium density fuels than UO 2 must be considered. To this end, uranium-molybdenum alloys were tested using the Fission Accelerated Steady-state Test (FAST) approach. The experiment test matrix is focused on identifying the temperature transition between low swelling and high fission gas retention to break away swelling and low fission gas retention. This paper documents the results of irradiation tests and post-irradiation examinations (PIE) including neutron radiography, rodlet profilometry, fission gas collection analysis, and optical metallography. The results of these tests showed that unconstrained U-Mo fuels (solid, Na-bonded rodlets) have a swelling threshold between 400-450°C with minimal fission gas release below this point. Higher temperature solid fuel showed microstructural zoning with small pore networks while lower temperature solid fuels have a uniform microstructure with large pore networks. U-Annular Mo fuels where swelling had some self-constraint imposed upon it, were shown to have much reduced swelling compared to their solid counterparts as well as very low fission gas release for irradiation temperatures up to 500°C. These initial results show that the use of U-Mo in constrained fuel geometries could be used as a high uranium density HALEU fuel for LWRs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Microstructural Evolution During a Solid State Tube Pinch Weld of Type 304l Stainless Steel

Microstructure development is examined for a specialized spot weld that is used as a solid-state closure process for austenitic stainless steel tubing, referred to as pinch welding. In order to elucidate the microstructural evolution of the weld, a series of test welds were made at nominal conditions using tubing and production like components. These pinch welds normally terminate after twelve cycles of a 60 Hz AC weld process. In this study, production tubes were welded from one to twelve cycles and the microstructure and weld variables after each individual weld cycle number were characterized using radiography and optical metallography. Two electrochemical etchants were used to highlight different microstructural features. The study revealed that: (1) this type pinch weld is largely complete after about six cycles of 60 Hz AC current, half the weld time utilized; (2) the resistance, deformation, and closure length approach “steady-state” conditions after six cycles; and (3) both oxalic and nitric acid electrolytic etchants are useful for highlighting specific microstructural attributes of type 304 L stainless steel. Finally, two distinct microstructural regions can be identified for these welds: the edge of the weld, which is driven by concentrated deformation, recrystallization, and grain growth, and the center region, which is more typical of forge welding and micro-asperity breakdown followed by diffusion and grain-growth.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Corrosion Studies of Pine-Derived Bio-Oil and Heavy Fuel Oil Blends

To reduce the amount of greenhouse gas produced from the combustion of petroleum fuels, renewable liquid fuels are needed. Pyrolysis of biomass provides a means to produce liquid fuels to displace current petroleum products. However, common ferrous alloys are susceptible to high corrosion rates when exposed to bio-oil. This study analyzes the effects of blending bio-oil derived from loblolly pine with heavy fuel oil added to reduce corrosion of common structural alloys. Laboratory corrosion studies of six different blends of bio-oil/heavy fuel oil were performed for 1,000 hours at 50°C. Chemical characterization was also performed to determine the total acid content of each blend. Post-exposure characterizations such as changes in weight, X-ray diffraction, dye penetrant testing, and metallography were performed to provide more insight into the corrosion mechanism of bio-oil/heavy fuel oil blends. We hypothesized that the corrosion rates of ferrous alloys would increase with an increase in bio-oil concentration. The results of these characterization and corrosion studies confirmed this hypothesis and will be reported.

09 BIOMASS FUELS↗
DOE OSTI2020

Status of the Characterization of DEs from the Full Circumference Examination of the Inner Container Closure Weld Region (FY2020)

One of the main focus areas of the 3013 Surveillance Program is a thorough evaluation of the inner container closure weld region (ICCWR) opened for destructive examination (DE). As part of the protocol to investigate the corrosion in the ICCWR a laser confocal microscope (LCM) is used to perform close visual examination of the surface and measurements of corrosion features on the surface. DE containers from FY13 through FY16 were screened with three candidates selected for full circumference evaluation (FCE) according to the ICCWR examination protocol, During the FCE, FY16 DE05 and FY15 DE07 showed suspect major corrosion events, FY16 DE05 Section C2 shows two crack-like features, identified as Denebola and Draco. Both features are located at the boundary of Zone 2 and Zone 3. Consequently, Section C2 of FY16 DE05 was selected for examination by serial metallography at Savannah River National Laboratory (SRNL). For FY15 DE07 the suspect corrosion events were observed on Sections Cl and C2. Section Cl shows one crack-like feature, identified as Acrux. Section C2 shows three crack-like features, identified as Bellatrix, Cursa Minor and Cursa Major. Unlike Acrux and Bellatrix, which are located at the boundary of Zone 2 and Zone 3, Cursa Minor and Cursa Major are located in Zone 2. Sections Cl and C2 of FY15 DE07 were sent to Los Alamos National Laboratory (LANE) for characterization by X-Ray Tomography (XRT).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Examination of Intergranular Crack on SC0234

The microstructure of the SC0234 weld was evaluated per DA-SPEC-01067, ''General Purpose Heat Source (GPHS) Plutonium-238 Dioxide Fueled Clad Product Specification'' and it was determined that the weld microstructure conformed to the quality requirements. During the examination of weld cross section, the metallographic analysis revealed the presence of a surface crack. Prior visual examination per RPS-TA55-303 had not revealed the crack, nor did the surface photography performed per RPS-TA55-302. The presence of the crack does not violate any of the product specifications called out on DA-SPEC-01067. Although there is a well-documented history of weld hot crack susceptibility in the early development of the DOP-26 iridium alloy, a surface crack such as this had not been documented during welding at Los Alamos. In the interest of better understanding the cause; the product engineer/program recommended further examination of the crack. This report discusses the examination of the crack found in the weld cross section of simulant clad SC0234. Metallography, Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy techniques (EDS) where used in the analysis of the crack and the surrounding weld microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Post Examination of Candidate NpO 2 Targets for 238 Pu Production

Four targets composed of sintered NpO 2 pellets enclosed in Zircaloy cladding were irradiated in the High Flux Isotope Reactor for 2 to 4 cycles to determine if an oxide pellet and Zircaloy cladding would be usable candidates for 238 Pu production. The pellets were sintered to a high fraction of theoretical density (TD) and melt wires were placed in small holes that had been drilled in the center of selected pellets to determine if the pellet centers exceeded desirable operating temperatures. After irradiation, the targets were punctured to determine the internal target pressure and the fission gas release. None of the targets had excessive pressure, and fission gas release was in the range of 4 to 38%. The targets were then cut into segments for radiochemical analysis, and metallography (MET) mounts were created to examine the pellet microstructure and to search for the melt wires to determine if they had melted. Three of the four targets resulted in successful MET mounts; the two-cycle pellets were too friable to be handled. No signs of pellet melting were noted, and unfortunately, none of the melt wires could be recovered. The results indicate that this pellet/clad design offers a practical option for 238 Pu production.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Discovering SPP Thermomechanical Pathways

Final report for SPPSi project in Thrust One Friction extrusion is a thermomechanical process that combines conventional extrusion with the action of a rotating die. The plastic deformation of the material being sheared and extruded is the primary source of process heat and it produces strain distributions unlike those resulting from conventional extrusion. This paper proposes an improved strain analysis that evaluates three main strain components in a series of rate-controlled friction extrusions in which the steady state was achieved. Cylindrical AA1100 extrusion billets with two embedded markers were extruded to wire with a 10:1 diametral reduction. The shape change of the embedded markers was determined via serial, transverse sectioning and quantitative metallography of the extruded wires. Three mutually orthogonal strain components (longitudinal, circumferential, and radial) were calculated at different positions along each extruded wire from the marker's shape change. The development of strain from the initial transient to the steady state is discussed. The variation of the steady-state strain with different process parameters is correlated with the die advance per revolution.

42 ENGINEERING↗
DOE OSTI2022

Creep and Fatigue Characterization of High Strength Alloy Thin Sections in Advanced CO2 Heat Exchangers

The objective of this work was to characterize and model elevated temperature creep and fatigue behavior for thin sheet and foil forms of gamma-prime strengthened alloys in wrought form and as-processed folded and brazed constructions. This work was motivated by the demanding temperature and pressure service conditions of the GEN3 Concentrated Solar Power (CSP) and supercritical CO2 (sCO2) power cycle working fluid. More specifically, the possibility of leveraging the superior creep strength of gamma-prime alloys in folded-fin and brazed-plate heat exchanger constructions. Gamma-prime alloys represent a step-change in raw-material strength over solid-solution strengthened alloys. And the folded-fin and brazed-plate heat exchanger architecture is lightweight and leverages cost-effective material stock forms. The investigation contained two parallel paths. (1) The first is referred to as a fundamental investigation where Oak Ridge National Laboratory conducts uniaxial creep testing on thin sheet and foil in wrought form. This effort aimed to serve as a benchmark against a relatively sparse existing database and a baseline comparison for path number 2. (2) The second path is referred to as the practical investigation where Brayton Energy manufactures plate-fin heat exchangers and performs pressurized creep and fatigue testing. This effort aimed to de-risk heat exchanger manufacturing process for service under sCO2 CSP conditions. A total of 14 uniaxial creep tests were completed using Haynes 282 thin sheet and foil. A variety of heat treatments were specified to coincide with path number 2. Baseline metallography of test samples and creep strength performance are contained. Benchmarks relatively to existing thick-form Haynes 282 are made, as well as to other thin-form Nickel-based superalloys. Description of a wrought-form modeling approach for thin gamma-prime alloys is also discussed. A total of 11 pressurized creep and fatigue tests were completed successfully with Haynes 282 heat exchanger prototypes. Manufacturing processing details, testing details, testing results, and failure analysis are discussed. Additionally, creep modeling techniques to predict failure are discussed, and modeling to support technological-to-market. In conclusion, Haynes 282 foils were demonstrated to yield rupture two-to-three orders of magnitude higher than Haynes 230 foils under similar conditions. And the manufactured heat exchanger prototypes demonstrated strength similar to the wrought constituents. Both of which contribute to elevated performance potential or cost savings in practice. Discussion is included.

14 SOLAR ENERGY↗
DOE OSTI2024

Using Additive Manufacturing to Repair Gas Turbine Hot Section Components

Ni-based superalloys are used in the hot sections of gas turbine engines due to their excellent high temperature performance. During service the material degrades due to exposure at high temperature and mechanical loads. Hence, utility provides often inspect, service, and repair components in gas turbine engines to ensure safe operation. A major challenge, however, is that the most heat-resistant alloys are generally considered ‘non-weldable’ rendering them difficult to repair via welding operations. In these cases components are often scrapped and then replaced by parts which must be re-manufactured. This burdens utilities with additional cost and supply chain issues can result in long term outages or reduced operating limtis. In this work EPRI and ORNL investigated a proposed repair strategy for gas turbine hot section components. Hot section superalloy GTD-111 was selected as a candidate repair material system and AM material ABD-900 the repair material. Sandwich structures were fabricated via electron beam melting additive manufacturing (EBM-AM) producing tensile bars with gage sections consisting of dissimilar ABD-900 / GTD-111 / ABD-900 material. Metallography revealed that the interface exhibited no deleterious phases or processing defeats. Creep rupture experiments on heat treated material demonstrates that the emulated repair coupons exhibit creep resistance between GTD-111 and ABD-900. This study demonstrates that the proposed EBM-AM repair strategy presents a viable opportunity towards enabling AM repair of gas turbine engine components.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Using Additive Manufacturing to Repair Gas Turbine Hot Section Components

Ni-based superalloys are used in the hot sections of gas turbine engines due to their excellent high temperature performance. During service the material degrades due to exposure at high temperature and mechanical loads. Hence, utility provides often inspect, service, and repair components in gas turbine engines to ensure safe operation. A major challenge, however, is that the most heat-resistant alloys are generally considered ‘non-weldable’ rendering them difficult to repair via welding operations. In these cases components are often scrapped and then replaced by parts which must be re-manufactured. This burdens utilities with additional cost and supply chain issues can result in long term outages or reduced operating limits. In this work EPRI and ORNL investigated a proposed repair strategy for gas turbine hot section components. Hot section superalloy GTD-111 was selected as a candidate repair material system and AM material ABD-900 the repair material. Sandwich structures were fabricated via electron beam melting additive manufacturing (EBM-AM) producing tensile bars with gage sections consisting of dissimilar ABD-900 / GTD-111 / ABD-900 material. Metallography revealed that the interface exhibited no deleterious phases or processing defeats. Creep rupture experiments on heat treated material demonstrates that the emulated repair coupons exhibit creep resistance between GTD-111 and ABD-900. This study demonstrates that the proposed EBM-AM repair strategy presents a viable opportunity towards enabling AM repair of gas turbine engine components.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Dissimilar metal joining of Ti-6Al-4V and Inconel 625

The dissimilar joining of Ti-6Al-4V and Inconel 625 by using a suitable interlayer shows potential design flexibility by avoiding the brittle intermetallic phases from direct welding. These phases include NiTi , NiTi 2 , and Ni 3 Ti . The objective of this work is to facilitate laser welding of Ti-6Al-4V and Inconel 625 through a vanadium interlayer to form an intermetallic free, strong, and corrosion resistant joint. Vanadium was chosen based on binary phase diagram solubilities, literature, and theoretical CalPhaD calculations in PanDat. Laser welding was systematically explored from based on beam mode, offset, power, and scan speed. Varied parameters include laser power from 325 to 650 watts, laser scan speed from 80 to 160 in/min, and beam offset up to a ¼ of the beam diameter. Parameters were chosen based on previous dissimilar joining research and those found in the literature. Metallography, including optical and scanning electron microscopy, was used to analyze the weld chemical composition, grain structure, and defects through both the fusion and heat affected zones. The results and discussion will examine the relationship between process parameters, microstructure, and observed weld defects. Our findings will not only assess the weldability of vanadium and Inconel 625 but also establish a transferable framework for studying other dissimilar material combinations, providing valuable insights for future research in this field.

36 MATERIALS SCIENCE↗
DOE OSTI2022

EDEN Tube Interface Characterization Report

In 2022 Eden Radioisotopes and Los Alamos National Laboratory entered into a Creative Research and Development Agreement (CRADA) leveraging the metallography capabilities of the Characterization and Special Projects Team of Sigma-2 at LANL. EDEN identified a need to characterize the condition of metallic interfaces within their product created at different pressure conditions to see which processing parameters achieved interfaces within specifications for intended use. A total of 4 samples were sent to the Characterization Projects team and 3 were later sent to another facility (MST-7) where Micro CT was performed.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Progress Report on SFR Metallic Fuel Data Qualification

This report summarizes the progress of SFR metallic fuel qualification related activities, which are focused on providing quality assurance relevant information applicable to experiments irradiated during the Integral Fast Reactor (IFR) program. An overview of the metallic fuel performance data and the associated databases, including the EBR-II Fuels Irradiation & Physics Database (FIPD), Out-of-Pile Transient Database (OPTD), and TREAT Experimental Relational Database (TREXR) is included. The legacy data in the databases, including as-built, post-irradiation examination (PIE), operating parameters, and out-of-pile experiment post-test data are introduced. The SFR metallic fuel Quality Assurance Program Plan (QAPP) and its implementation to qualify these legacy data is described in detail. Important PIE data QA documents and the specifications of seven types of PIE measurements (contact profilometry, laser profilometry, neutron radiography, gamma scan, fission gas release fission gas chemistry, and metallography) are provided. Examples of the implementation of the QAPP to qualify each of those types of PIE data are provided.

Mo, Kun [Argonne National Laboratory (ANL), Argonn↗
DOE OSTI2024

Enhancing NDE Reliability for Grade 91 Steel Welds: Ultrasonic Imaging and Microstructural Correlations

Ensuring the integrity of Grade 91 (9Cr-1Mo-V) steel welds is vital for the safe and reliable operation of fossil fuel–fired and nuclear power plants. Here, this study applies an imaging technique for the ultrasonic characterization of two Grade 91 steel welds created with cold metal transfer and flux-cored arc welding processes. Ultrasonic immersion testing in the through-transmission configuration was employed to generate shear waves, which helped identify the weld metal, heat-affected zone, and base metal regions. These weld microstructures were also correlated to their ultrasonic images using metallography, ultrasonic amplitude, hardness measurements, and grain size. The findings from this study can assist practitioners in developing new nondestructive evaluation technologies, improving the inspection reliability of creep strength–enhanced ferritic steel welds by potentially identifying weld microstructure regions susceptible to creep-type failures.

Grade 91 steel↗
DOE OSTI2023

Post irradiation examination of a uranium-zirconium hydride TRIGA fuel element

Low-enriched (LEU) U-ZrH fuel, with a 235 U content less than 20% of the total uranium, is being evaluated for possible use in different types of reactors, including space nuclear systems, light water reactors (LWRs) and micro-reactors. As a result, it is beneficial to better understand the macrostructural and microstructural changes that occur in this fuel during irradiation. This paper reports the results of the post irradiation examination of an LEU U-ZrH fuel element (30 wt.% U, <20% 235 U) using neutron radiography, precision gamma scanning, chemical analysis, optical metallography and scanning electron microscopy combined with energy dispersive spectroscopy and wavelength dispersive spectroscopy, where the fuel element was irradiated in a Training, Research, Isotope, General Atomics (TRIGA) reactor. Results of microstructural characterization indicated some dehydriding and cracking of the U-ZrH fuel occurred during irradiation; an axial and radial burnup gradient existed in the fuel during irradiation, as measured by gamma scanning and chemical analysis; negligible microstructural changes transpired during irradiation, based on comparison of irradiated and as-fabricated U-ZrH fuel microstructures; and, negligible, fission product-rich, phases could be resolved in a U-ZrH fuel that was irradiated to a calculated 20% depletion of 235 U.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Impact of Hydrogen Combustion on the Oxidation-induced Degradation of Heavy-duty Diesel Engine Piston Materials

High temperature ferritic-martensitic steels are candidate materials for heavy-duty diesel engine pistons. The envisioned transition to hydrogen blended fuels is expected to alter the post-combustion atmosphere in the engines, primarily resulting in a higher water vapor content (> 20 vol%) and potentially higher exhaust gas temperatures. The oxidation resistance of existing and newly developed alloys will be a critical life-limiting mechanism under these conditions. In the present work, the oxidation behavior of candidate piston alloys was evaluated in air+10 vol.% H2O and air+30 vol.% H2O at 700°C. Thermal cyclic (1h cycle) exposures were conducted for two variants of commercial UNSS42200 ferritic-martensitic steel and two developmental alloy steels for up to 300h. The developmental alloys each have similar compositions but with one containing elevated Cu levels of 3 wt.%, A significant reduction in resistance to breakaway oxidation was observed for the commercial alloys in the higher water vapor atmosphere. Microstructural characterization (optical metallography, scanning electron microscopy and electron microprobe analysis) revealed the formation of thick Fe-rich oxides even for the high Cr (~12 wt.%) steels after an initial stage of protective oxidation with MnCr-rich spinels. The impact of the evaporation-induced loss of Cr on the time and temperature dependent compositional changes in the alloys was correlated with experimental findings. For the developmental alloys, Cu additions appear to play a role in significantly reducing oxidation kinetics in air+30 vol.% H2O at 700°C.

Pillai, Rishi [ORNL] (ORCID:0000000243688197)↗