SEARCH · Search NASA

Results for “motion estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Edgewise Structural Damping of a 2.8-MW Land-Based Wind Turbine Rotor Blade

Modern wind turbines push the predictive capabilities of state-of-the-art aero-servo-elastic tools. The existing limitations hide across the numerical tool chain and can result in serious issues, such as missing aeroelastic instabilities during the design phase. Structural damping is an input that is usually hard to estimate, but also has a major impact on the turbine behavior. In this paper, we discuss an experiment that aims to accurately quantify the structural damping characterizing the edgewise modes of modern wind turbine blades. The experiment is carried out on a 2.8-MW land-based wind turbine and features a fast yaw actuation that induces an edgewise motion on one of the three blades. The Covariant-subspace system identification (Cov-SSI) method is then used to post-process the blade root moment to estimate the short-term edgewise structural damping. Despite limitations of the Cov-SSI method, which consistently under-predicts the absolute values of damping, we observe that structural damping decreases across the first three blade edgewise modes, which is different from the stiffness-proportional damping model that assumes that structural damping increases with the modes. This paper argues that a stiffness-proportional damping model, which is implemented in most aeroelastic tools, is therefore not conservative and might hide aeroelastic instabilities that can instead appear in the field.

17 WIND ENERGY↗

DOE OSTI2024

A Vision–based Robust $\mathcal{H}$ ∞ Gain Scheduling Longitudinal and Lateral Following Controller for Autonomous Vehicles on Urban Curved Roads

Implementing advanced driver assistance systems (ADAS) in congested and intricate urban traffic scenarios poses significant challenges. To address the frequent stop–and–go motions exhibited by autonomous vehicles (AVs) navigating urban roads with changes in curvature, we propose a vision–based robust $\mathcal{H}$ ∞ adaptive cruise control system (ACC) for longitudinal control, plus a lane keeping assist system (LKAS) for lateral control. For the vision-based ACC, a weighted probability objective function for the vehicle following behavior is formulated. We incorporate $\mathcal{H}$ ∞ performance and gain scheduling techniques to mitigate the impact of uncertainty in visual sensor measurements. Furthermore, the optimal time headway is scheduled based on the velocity to ensure traffic flow efficiency and safety during the vehicle following process. For the LKAS, we introduce a road curvature estimation method that integrates lane and vehicle dynamics information to obtain the lateral and heading offsets. Next, the design criterion of the observer–based robust gain scheduling lateral motion controller is established by linear matrix inequality (LMI). Here, a series of experiments conducted within a camera–in–loop platform validate the proposed method.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2024

Differentiable vertex fitting for jet flavor tagging

This work explores the use of differentiable programming to integrate domain knowledge, in the form of domain specific software, into neural networks to develop scientific machine learning systems. We propose a differentiable vertex fitting algorithm that estimates the crossing point of multiple curves. In the high energy physics setting, these curves are defined by particle equations of motion and the crossing point represents the origin of particle production. This differentiable vertex fitting algorithm can be seamlessly integrated into neural networks, and we show its utility and efficacy in the high energy physics application of the classification of jets, i.e., collimated streams of particles in particle detectors whose originating parent particle we aim to classify. We demonstrate how differentiable vertex fitting can be integrated into larger transformer-based models for jet flavor tagging and show improvements in heavy flavor jet classification when compared to baseline models. Published by the American Physical Society 2024

Smith, Rachel E. C. (ORCID:0000000335851262)↗

DOE OSTI2024

Temporal Explosion Source Processes of Declared Nuclear Tests in the Democratic People’s Republic of Korea

In this work we highlight a preliminary temporal source analysis of the six declared Democratic People's Republic of Korea (DPRK) nuclear tests. We use regional seismic data to estimate relative source time functions (RSTFs) via iterative time-domain deconvolution (Ammon, 2006; Pippin, 2022) of vertical-component ground motions recorded within 2000 km of the source region. Since RSTFs are ideally independent of site and propagation effects, their amplitude spectrum is equivalent to the source spectral ratio, but they also retain phase information. We compare observed RSTFs (in the time and frequency domains) with synthetic RSTFs derived from the Mueller & Murphy (1971) explosion source model. The resolution of these time functions varies, however, we generally obtain high-quality results within the limitations of the recording broadband instrumentation. The results indicate that this method effectively preserves source time-history information that can be used for temporal analysis of remote nuclear explosions. This preliminary analysis is intended to assess the viability of using time-domain deconvolution methods for extracting temporal source information.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

DOE OSTI2025

Three-Dimensional Heat Flux and Thermal Analysis of Angled Tungsten Samples on DIII-D

ITER-grade tungsten and dispersoid-strengthened tungsten samples with the top surface angled at ~15° towards the incident plasma flux were exposed to 9 H-mode discharges with edge-localized modes (ELMs) in the lower divertor of DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Surface damage included cracking and flaking of material on the two samples farthest away from the plasma strike point, and significant melting of the two samples closest to the strike point. Heat flux and thermal analysis tools new to DIII-D have been applied to better understand this material response and to help optimize the exposure conditions for future experiments. SMITER field-line tracing simulations based on IRTV data and EFIT equilibria estimate an average inter-ELM perpendicular heat flux, 𝑞⊥,𝑖nter−𝐸LM , on the angled surfaces of 10.1 – 19.6 MW/m² for a majority of the 9 discharges, increasing to 15.6 – 24.5 MW/m² for the single, higher-power shot where samples melted. Fast camera data showed shallow intra-ELM melting and re-solidification, which transitioned to bulk inter-ELM melting with melt motion in the 𝐽⃗ 𝑥 𝐵⃗ direction. About 50% of the protruding volume of the most affected sample was displaced via melt-motion. SIERRA thermal modeling software was able to reproduce an onset time of melting consistent with fast camera data and final sample conditions, within < 200 ms. Maximum surface temperatures of 3122 K and 2787 K are estimated for the samples farthest away from the strike point, while the closest samples achieve melting at 4067 ms and 4750 ms into the ~5000 ms plasma exposure. A +10% increase in both the SMITER 𝑞⊥,𝑖nter−𝐸LM calculations and the estimated ELM heat loads 𝑞⊥, 𝐸LM was required to achieve this result, which is within the uncertainty of the diagnostic data but likely accounts for non-ideal geometry effects plus other physics uncertainties not included in this first iteration of modeling. This work provided valuable estimates of the 3D temperature evolution to help better understand the observed surface morphology and internal recrystallization of samples, which are discussed in detail in a complementary manuscript [1]. Benchmarking efforts with more diagnosed DIII-D experiments are underway to further refine the SMITER and SIERRA models for DiMES. Future use of these tools will enable researchers to precisely target heat flux exposure conditions in DIII-D to test, but not exceed, the thermomechanical limitations of novel plasma-facing materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Performance assessment of near-fault buildings subjected to physics-based simulated earthquake ground motions with fling step

The effects of the co-seismic static offset (known as fling step) and associated velocity pulses on civil structures have been difficult to study because the static offset is typically removed during the processing of earthquake ground motion records. Simulated ground motions contain fling features and require no processing; therefore, they create new opportunities for representing fling features in seismic hazard analysis and assessing their influence on the seismic demands on near-fault structures. We use physics-based fault rupture simulations to study the characteristics of ground motions with fling step and the sensitivity of the near-fault structural demands to strong fling features. We uncover that simulated ground motions with a large fling step tend to have higher spectral intensity than those without a fling step at the same rupture distance, especially at periods longer than 2 s. As a result, the structural demands on flexible buildings tend to be the most sensitive to the fling features. Statistical analysis suggests that the ground motion spectral shape (represented by spectral accelerations at multiple periods) is—in most cases—a sufficient predictor of the structural demands on near-fault low-rise and mid-rise buildings at locations that are susceptible to strong fling effects. Finally, ground motion record selection experiments reveal that representing the spectral shape features at periods that are most relevant to a given structure may be an effective strategy to reduce the bias in the estimated demands on near-fault long-period structures when the available database of records is considered deficient in fling features.

Fling step↗

DOE OSTI2025

Bulk Motions in the Black Hole Jet Sheath as a Candidate for the Comptonizing Corona

Abstract Using two-dimensional general relativistic resistive magnetohydrodynamic simulations, we investigate the properties of the sheath separating the black hole jet from the surrounding medium. We find that the electromagnetic power flowing through the jet sheath is comparable to the overall accretion power of the black hole. The sheath is an important site of energy dissipation as revealed by the copious appearance of reconnection layers and plasmoid chains. About 20% of the sheath power is dissipated between 2 and 10 gravitational radii. The plasma in the dissipative sheath moves along a nearly paraboloidal surface with transrelativistic bulk motions dominated by the radial component, whose dimensionless 4-velocity is ∼1.2 ± 0.5. In the frame moving with the mean (radially dependent) velocity, the distribution of stochastic bulk motions resembles a Maxwellian with an “effective bulk temperature” of ∼100 keV. Scaling the global simulation to Cygnus X-1 parameters gives a rough estimate of the Thomson optical depth across the jet sheath, ∼0.01–0.1, and it may increase in future magnetohydrodynamic simulations with self-consistent radiative losses. These properties suggest that the dissipative jet sheath may be a viable “coronal” region, capable of upscattering seed soft photons into a hard, nonthermal tail, as seen during the hard states of X-ray binaries and active galactic nuclei.

Sridhar, Navin (ORCID:0000000255199550)↗

DOE OSTI2024

Timber Harvesting Economics in Early Commercial Thinning and Group Selection Prescriptions

Forest management decisions that consider both short- and long-term objectives are becoming more challenging and costly, due to market uncertainty, labor shortages, and the evolving forest industry. Under such unpredictable circumstances, a better understanding of the production economics of various silvicultural prescriptions is crucial in implementing sound forest management activities. The objectives of this study were to: a) estimate stump to landing productivity and cost for Early Commercial Thinning (ECT) and Group Selection (GS) prescriptions; and b) compare the harvest system cost ($/PMH) using machine rate and PATH (Planning and Analysis in Timber Harvesting) methods. Detailed time-motion studies were conducted in the spruce-fir forest of Northern Maine, USA, during the summer of 2019. The results, as expected, indicated the harvesting costs were 23% higher for ECT (21.08 $/m3) compared to GS (16.32 $/m3). The average productivity of the harvester and forwarder were reduced by 15 and 37%, respectively, for ECT compared to GS. The estimated harvesting system cost ($/PMH) was 4% higher as indicated by PATH compared to machine rate method. Higher operational productivity in GS can be attributed to the larger volume of logs, and shorter travel loaded distance than ECT. These findings can help forest managers make more informed decisions while implementing appropriate silvicultural prescriptions under varying conditions based on management objectives and market conditions.

Forestry↗

DOE OSTI2026

Constraining the Galactic bar using the M92 stellar stream

Stellar streams are excellent probes of the gravitational potential in which they evolve. In the Milky Way (MW), globular cluster (GC) streams are routinely used to infer properties about time-dependent perturbations of the underlying potential. This implies that streams with Galactocentric radii small enough to be perturbed by the MW bar should offer constraints on it, such as its pattern speed, which currently has a wide range of values reported in the literature and is important when studying stellar kinematics. The GC M92 has a small pericentre and should be affected by the bar. It has a diffuse stellar stream, but confirming stream members has previously been hindered by a lack of spectroscopic data. In this paper, we use Dark Energy Spectroscopic Instrument (DESI) observations together with photometric and astrometric data to obtain spectroscopic members of the M92 stream for the first time. We identify a clear spatial distribution and gradients in distance moduli, proper motions, and radial velocities that confirm the stream's existence. We compare the observed stream to mock streams generated in different barred potentials and estimate the MW bar's pattern speed $Î©= 29.1^{+0.7}_{-0.4}$ km s$^{-1}$ kpc$^{-1}$ and $\dot Î©= 0.7^{+3.5}_{-2.3}$ km s$^{-1}$ kpc$^{-1}$ Gyr$^{-1}$. This is the first time a stellar stream is used to probabilistically infer these bar properties, and it opens up an exciting realm of inner Galactic potential characterisation using stellar streams.

Byström, Amanda [Edinburgh U., Inst. Astron.] (ORC↗

DOE OSTI2025

Atomistic Investigation of Plastic Deformation and Dislocation Motion in Uranium Mononitride

Uranium mononitride (UN) is a promising advanced nuclear fuel due to its high thermal conductivity and high fissile density. However, many aspects of its mechanical behavior, particularly at reactor-relevant conditions, remain unclear. In this study, molecular dynamics (MD) simulations were employed to investigate the deformation behavior and dislocation motion in UN. We found that the Kocevski potential predicts the principal slip system as $\frac{1}{2}$ $\langle110\rangle${110}, aligning with experimental data. On the other hand, the Tseplyaev potential predicts slip to primarily occur on $\frac{1}{2}$ $\langle110\rangle${111}. MD simulations of stress–strain behavior were used to estimate the nanoindentation hardness, revealing that the Kocevski potential accurately predicts hardness even though it fails to model dynamic plasticity. Complete dislocation mobility functions have been fitted for the edge and screw dislocations in both the thermally activated and phonon-drag regimes. The 300 K linear mobility of the edge dislocation using the Tseplyaev potential was found to be 817 Pa -1 ·s -1 , whereas that of the screw dislocation using the Kocevski potential was found to be 4546 Pa -1 ·s -1 . At intermediate stresses, we observed that the subsonic steady-state motion of the edge dislocation in UN is intermittently interrupted by velocity jumps, reaching the average sound velocity. Finally, the threshold Schmid stress is calculated as 179–197 MPa, which gives an upper-limit estimate of the uniaxial yield stress of polycrystalline UN of 548–603 MPa. These findings, including the fitted dislocation mobility function, provide essential input for future plasticity and dislocation dynamics models of nuclear fuels.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Simplified Approximations of Direct Cumulus Entrainment and Detrainment

Abstract In recent years, direct calculations of simulated cumulus entrainment and detrainment have facilitated new physical insights into these highly elusive but critically important processes. However, these calculations require substantial computational resources that may limit their widespread usage. To facilitate such calculations, two simplified approximations of direct cumulus entrainment and detrainment are examined herein. The first approximation, termed the “semidirect” method, follows a standard bulk approach but makes more realistic assumptions about the sources of entrained and detrained air near the cloud edges. In contrast, the second approximation (the “projection” method) uses the governing equations of motion to project whether grid points near the cloud edge will entrain or detrain as the mean cloud ascends by one grid point. Verification exercises using large-eddy simulations reveal that both methods generally agree better with corresponding direct entrainment/detrainment estimates than the traditional bulk formulation, with the projection method outperforming the semidirect method. The two methods can be used in a synergistic fashion, with the semidirect method helping to optimize the projection method, to suit a wide range of applications. Because the latter incorporates the essential dynamics of entrainment and detrainment at the local scale, it can be used to gain physical insight into the causal mechanisms regulating these complex processes.

Meteorology & Atmospheric Sciences↗

DOE OSTI2025

Observation of Electromagnetic Transients in a Nb3Sn 4-layer Dipole Mirror Magnet

During testing of the Stress Managed Cosine-Theta dipole mirror magnet SMCTM1, magnet quenches were observed following large voltage spikes in the half-coil voltage taps which preceded normal quench initiation. Following some recent work at CERN measuring power current converter transients in relation to flux jumps, an additional differential current probe was added to the magnet instrumentation. Measurements of this probe, as well as the half coil voltage taps show a fast and substantial current change preceding the quench, hinting at coil motion. A simple model based on relative shift of the inner and outer layer coils was developed which suggests the magnitude of coil shift events is on the estimated relative coil shift from the magnet constraint conditions. The behavior is shown to be reversible and characteristic of stick-slip.

Krave, Steven [Fermilab] (ORCID:0000000217521457)↗

DOE OSTI2025

A quality-agnostic combinatoric cost estimation model for large-format directed energy deposition metal additive manufacturing

Directed energy deposition (DED) additive manufacturing (AM) processes are amenable to synergistic combination into multi-process AM systems due to similar requirements for automation and energy sources. This work analyzes the economic performance of such DED AM systems from a quality-agnostic combinatoric standpoint with a model that calculates lowest-cost system combinations based on part geometry and process performance metrics. Common DED AM systems research focuses on a single process and does not consider the process, system, and application in the context of all possible system combinations (e.g., the combined set of process selection(s), motion system(s), and process hardware), leading to limited applicability of the resulting DED AM systems to cost-sensitive components such as those found in energy generation applications. The model developed herein incorporates the capital, material, and energy costs associated with DED AM system combinations into a predictive tool for estimating part and system cost, the output of which is intended to guide deployment of finite research and development resources towards DED AM system combinations with the lowest costs and greatest likelihood of economic impact. The DED AM systems identified by this framework may enable domestic production of the large conventionally cast and forged components necessary for energy generation.

Shanafield, Alexandra [ORNL]↗

DOE OSTI2024

Capturing many-body correlation effects with quantum and classical computing

Theoretical descriptions of excited states of molecular systems in high-energy regimes are crucial for supporting and driving many experimental efforts at light source facilities. However, capturing their complicated correlation effects requires formalisms that provide a hierarchical infrastructure of approximations. These approximations lead to an increased overhead in classical computing methods and, therefore, decisions regarding the ranking of approximations and the quality of results must be made on purely numerical grounds. The emergence of quantum computing methods has the potential to change this situation. Here, in this study, we demonstrate the efficiency of the quantum phase estimator (QPE) in identifying core-level states relevant to x-ray photoelectron spectroscopy. We compare and validate the QPE predictions with exact diagonalization and real-time equation-of-motion coupled-cluster formulations, which are some of the most accurate methods for states dominated by collective correlation effects.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2025

In-Situ Synchrotron X-Ray Diffraction of Ultrasonic Microstructural Refinement During Solidification in a Commercial Al–Si–Mg Alloy

This study reports the first use of in-situ synchrotron X-ray diffraction (SXRD) to study the effects of ultrasonic melt processing (USMP) on phase and grain size evolution during solidification in a commercial Al–Si–Mg casting alloy. USMP is a technique that, when applied to aluminum as it solidifies, can be used to refine the local microstructure of large-scale castings. Analysis of the in-situ SXRD data to estimate the average grain size of primary α-Al grains during USMP demonstrates that USMP slows the growth rate of α-Al grains and reduces grain size by 36 pct. Furthermore, there is also evidence that USMP causes the primary α-Al grains to move relative to the X-ray beam; such motion increases the probability of primary α-Al grains colliding and fragmenting. This movement becomes constrained at the onset of the Al–Si binary eutectic, suggesting that USMP ceases to effectively refine the microstructure once the Al–Si binary eutectic begins to form. Complementary laboratory-scale X-ray diffraction (XRD) data were used to correlate the lattice parameters of the α-Al and Si (D-A4) phases with temperature to estimate cooling rate during solidification. Thus, this study can guide the design of novel castings with spatially distributed fine-grained regions produced using local ultrasonic processing.

Aluminum Alloys↗

DOE OSTI2026

From observation to replication: machine-learning-driven quantification and replication of fine-scale fish kinematics and behavior

Long-term quantification of fish behavior is essential for aquatic ecology, wildlife telemetry, and biomechanical device development. However, the observation duration required to obtain reliable behavioral and kinematic metrics remains unclear, and few tools exist to physically reproduce natural swimming motion for controlled experimentation. We address these challenges by developing a generalizable framework that models behavioral reliability (Spearman–Brown reliability index) as a function of observation duration and derives metric-specific monitoring thresholds. Using juvenile white sturgeon (Acipenser transmontanus) as a case study, we demonstrate that the minimum duration needed for reliable estimates varies substantially across kinematic features: to exceed a reliability of 0.8, total distance traveled requires 12 days, average curvature (mm?¹) 15 days, tail-beat frequency (Hz) 8 days, and average speed (body length/s) 17 days. We further bridge digital analysis and physical testing by developing a hardware-in-the-loop simulator that reconstructs machine-learning-derived swimming kinematics with high fidelity (correlation coefficient 0.98–0.99, RMSE 1.22–1.27 mm over a 5-minute segment). This platform enables realistic, repeatable motion stimuli for evaluating aquatic sensing technologies and bio-integrated devices under controlled conditions. Together, these contributions provide a scalable approach for designing long-term behavioral studies and a data-driven connection between ecological observation and robotic experimentation.

Hwang, SungJoo↗

DOE OSTI2024

Stellar Metallicities from DECam $u$-band Photometry: A Study of Milky Way Ultra-Faint Dwarf Galaxies

We conducted an in-depth analysis of candidate member stars located in the peripheries of three ultra-faint dwarf (UFD) galaxy satellites of the Milky Way: Boötes I (Boo1), Boötes II (Boo2), and Segue I (Seg1). Studying these peripheral stars has previously been difficult due to contamination from the Milky Way foreground. We used $u$-band photometry from the Dark Energy Camera (DECam) to derive metallicities to efficiently select UFD candidate member stars. This approach was validated on Boo1, where we identified both previously known and new candidate member stars beyond five half-light radii. We then applied a similar procedure to Boo2 and Seg1. Our findings hinted at evidence for tidal features in Boo1 and Seg1, with Boo1 having an elongation consistent with its proper motion and Seg1 showing some distant candidate stars, a few of which are along its elongation and proper motion. We find two Boo2 stars at large distances consistent with being candidate member stars. Using a foreground contamination rate derived from the \emph{Besan\c{c}on} Galaxy model, we ascribed purity estimates to each candidate member star. We recommend further spectroscopic studies on the newly identified high-purity members. Our technique offers promise for future endeavors to detect candidate member stars at large radii in other systems, leveraging metallicity-sensitive filters with the Legacy Survey of Space and Time and the new, narrow-band Ca HK filter on DECam.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2026

Ecological Insights from Transferable Plant Biomass Mapping across the Arctic using High-resolution Structure-from-Motion and LiDAR Data

Warmer temperatures, permafrost thaw, and increased wildfire activity are driving rapid ecological change across the Arctic, significantly altering plant productivity and aboveground biomass (AGB). These rapid changes highlight the urgent need to improve monitoring of vegetation dynamics in the Earth’s northern ecosystems, where high spatiotemporal heterogeneity occurs at scales finer than those captured by traditional satellite observations. The growing use of Unoccupied Aerial Systems (UASs) presents an opportunity to overcome this limitation. Yet, the diversity of UAS platforms, sensors, and data collection and processing workflows presents challenges for developing standardized, generalizable approaches. To address this challenge, we compiled 672 AGB plots co-located with 183 UAS-based Structure-from-Motion (SfM) or Light Detection and Ranging (LiDAR) surveys collected across the Arctic. Here, we: (1) evaluated the generalizability of UAS-derived canopy structure derived from high-resolution SfM and LiDAR for estimating AGB, (2) assessed scaling errors and their sources in two recent satellite-based AGB products derived from Landsat and MODIS, and (3) demonstrated the use of high-resolution AGB maps to quantify biomass variation across tundra plant functional types (PFTs) and to monitor post-fire recovery. Our results show that both SfM and LiDAR accurately captured AGB and its variability across tundra PFTs using a Random Forest (RF) model (overall RMSE: 0.336 kg/m2), with mapping performance varying slightly by region and data source. Using UAS-derived AGB maps as a benchmark, we identified systematic biases in satellite-derived AGB products, largely attributable to the magnitude of AGB and structural heterogeneity within coarse-resolution pixels. Applying our model to repeat UAS surveys following a tundra fire on Seward Peninsula, we observed rapid AGB recovery in non-shrub patches, with biomass recovering to pre-fire levels within 2 years. In contrast, shrub patches recovered more slowly, with AGB gains continuing over 2–4 years through both in-patch growth and lateral expansion (via dispersal) into remaining burned areas. Overall, these findings demonstrate the generalizability of UAS-based SfM and LiDAR data for estimating tundra AGB and highlight the potential of our approach to be broadly applied to generate high-quality AGB data for ecological monitoring and model benchmarking across the Arctic.

Yang, Daryl [ORNL] (ORCID:0000000317057823)↗