Search NASA⌕ Search

SEARCH · Search NASA

Results for “motors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Flux Switching Permanent Magnet Motor with Metal Amorphous Nanocomposite Soft Magnetic Material and Rare Earth Free Permanent Magnets

The power losses in high power-density motors due to high rotational speed and/or high pole counts may be reduced adopting metal amorphous nanocomposites (MANCs) featuring low power loss and a relatively high flux density (~1.3 T). We recently proposed a flux switching permanent magnet (FSPM) motor with a rating of 2.5 kW at 1400 Hz electrical speed by incorporating low loss (< 3 W/kg at 1 kHz) FeNi-based MANC material with projected iron loss of about 5 W. The motor design allows use of rare earth-free permanent magnets. For incorporation of MANC materials, an axial flux motor where the rotor and stator core are made from a wound ribbon core has been developed. We have performed a 3-d FEA to optimize the design and built and tested a prototype demonstrating that the low loss MANC material can be used for motor applications.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Design of BLDC Motor Diagnostic Device Based on Surge Test for Phase to Ground Fault

BLDC motor is essential in the industrial world, especially it been used for an electric vehicle. The benefit of using BLDC motor is that it has high rate efficiency and low mechanical losses. However, to know the isolation condition of winding and increase reliability, it needs to be tested. With the implementation of surge test based fault detection device of BLDC motor, the condition of BLDC motor can be monitored and maintained according to analysis of its condition. The surge test method used because it is sensitive in detecting the initial damage in the isolation failure process on stator winding. A surge voltage is generated from the Cockroft-Walton and switching circuit with capacitors. The result is analyzed using Error Area Ratio (EAR). The test result shows that the higher the value of resistance and inductance, the smaller the frequency of the surge wave. When the BLDC motor in a parallel short circuit condition, the threshold value of the EAR test-reff has a minimum value of 5.28%, an average of 13.52%, and a maximum of 28.55%.

BLDC motor↗
DOE OSTI2020

Coupled Electro-Thermal Analysis of Permanent Magnet Synchronous Motor for Electric Vehicles

Permanent magnet synchronous motors (PMSM) are extensively used in electric vehicles. However, high internal heat generation and inefficient heat dissipation often limit the operational reliability, and longevity of the PMSM. Therefore, proper quantification of heat generation in electric motor and advanced embedded motor cooling techniques remain topics of immense interest. In order to accurately predict electro-magnetic performance, i.e., efficiency, component-wise heat losses and the corresponding temperature distribution of a jacket cooled machine, this paper presents a two-way iteratively coupled electro-thermal modeling framework. Finite element based software Motor-CAD has been utilized for electro-magnetic performance calculation of BMW i3 PMSM. Finite volume based computational fluid dynamics/heat transfer (CFD/HT) software ANSYS® FLUENT® has been employed to simulate the temperature distribution of the PMSM, using the electro-magnetic losses as heat input. Computed heat losses, stator, winding, rotor, and magnet temperatures are utilized as coupling parameters between the electro-magnetic and thermal models. A conventional one-way coupling algorithm has also been developed and compared to the newly proposed two-way coupling algorithm. Numerical results confirm that at high current density, one-way coupling algorithm significantly over-predicts the motor temperature compared to the two-way algorithm. A comprehensive analysis has been carried out to characterize the influences of current density, speed, and forced convection heat transfer coefficient on the heat losses, overall efficiency, and maximum temperature of the PMSM. Lastly, an efficiency map has been interpreted from the coupled electro-magnetic simulation.

42 ENGINEERING↗
DOE OSTI2025

Experiments in 3D Printing Electric Motors

This paper catalogues a series of experiments we conducted to explore how to 3D print a DC electric motor. The individual parts of the electric motor were 3D printed but assembled by hand. First, we focused on a rotor with soft magnetic properties, for which we adopted ProtoPasta TM , which is a commercial off-the-shelf PLA filament incorporating iron particles. Second, we focused on the stator permanent magnets, which were 3D printed through binder jetting. Third, we focused on the wire coils, for which we adopted a form of laminated object manufacture of copper wire. The chief challenge was in 3D printing the coils, because the winding density is crucial to the performance of the motor. We have demonstrated that DC electric motors can be 3D printed and assembled into a functional system. Although the performance was poor due to the wiring problem, we showed that the other 3D printing processes were consistent with high performance. Nevertheless, we demonstrated the principle of 3D printing electric motors.

3D printed motor↗
DOE OSTI2023

Implementation of a Metamodel-Based Optimization for the Design of a High Power Density Wound Field Traction Motor

Traction motors onboard electric vehicles (EVs) are faced with ever-increasing power density requirements and cost reduction challenges. Although permanent magnet (PM) traction motors have been favored for their potential of higher power densities, the price and supply volatility of PM materials are the major drawbacks. Instead of a single load point, the performance of a traction motor needs to be optimized over various combinations of torque and speed to represent real-world vehicular driving scenarios, which tends to be a time-consuming task with direct optimizations. In this study, as a PM-free solution, a wound field synchronous motor (WFSM) is designed and optimized using a metamodel-based approach to maximize its efficiency over a custom set of load points, while utilizing a fully per-unitized geometry template. The workflow has proven to be timesaving and the optimal design is prototyped and tested.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Construction of Photo‐Responsive Pd 2 L 4 ‐Type Nanocages based on Feringa's Second‐Generation Motor and Its Guest Binding Ability for C 60

Abstract We present the construction of a M 2 L 4 ‐type metal‐organic nanocage featuring four endohedral Feringa's motor motifs and its adaptive encapsulation towards a C 60 guest molecule. The structure of the cage, though complicated on the 1 H NMR spectrum due to the adoption of mixed ligands, was unambiguously characterized with a combination of ESI‐MS, 2D DOSY, 13 C NMR and particularly the SAXS technique. The molecular motor within the cage demonstrated similar photophysical properties to the uncoordinated one, indicating the motor's function was not compromised when it was anchored in such a confined nanospace. Furthermore, the nanocage showed good guest encapsulation ability towards C 60 , and a guest induced‐fit behavior of the cage was revealed based on the extensive SAXS analysis and molecular dynamics simulation. The adaptive motorized nanocage reported here represents one of the very few examples of integrating individual motors into a discrete nanoconfined system and offers prospects to achieve its non‐equilibrium functions.

Chemistry↗
DOE OSTI2020

Effects of blending C3-C4 alcohols on motor gasoline properties and performance of spark ignition engines: A review

Supplementing petroleum fuels with sustainable and renewable alternatives is a good option for increasing the sustainability of transportation fuels. Alcohols are particularly attractive blendstocks for spark ignition engines, mainly due to their desirable fuel properties including high octane, evaporative cooling, and reduced sooting propensity. Although the use of SI engines is widespread around the world, predominately for light duty vehicles, concerns about CO2 emissions and other sustainability issues necessitate increased engine efficiencies, reduced tailpipe pollutants, and lower lifecycle carbon emissions. The intelligent blending of C2-C4 alcohols into motor gasoline is a viable method for achieving these goals. There are a multitude of ways to produce renewable alcohols such as through fermentation from first-generation feedstocks (sugar and corn) and second-generation feedstocks (lignocellulosic biomass), or by gasification and mixed alcohol fuel synthesis routes from lignocellulosic biomass. Currently ethanol is extensively used in motor gasoline fuels worldwide and although many have proposed the use of C3 and C4 alcohols in motor gasoline as an improvement over ethanol, the higher cost of production and lack of clear definition as to their benefit over ethanol when blended into motor gasoline have led to slow acceptance into the market. In this review, special emphasis is placed on the effects of blending C3 and C4 alcohols into motor gasoline in terms of physicochemical properties, volatility behavior, and engine performance when compared to ethanol blends. Furthermore, the impact of blending C3 and C4 alcohols with gasoline on emission (particulate matter, nitrogen oxides, carbon monoxide, hydrocarbons, and unregulated oxygenates) and combustion (volumetric efficiency, thermal efficiency, fuel consumption, and cold performance) characteristics is discussed. Although there are some disagreements in the literature over the effect of alcohols predominately around the type of SI engine, i.e., port fuel injected versus direct fuel injected and engine operating mode, generally it is stated that alcohols can potentially reduce soot, unburned hydrocarbons and CO emissions while increasing thermal efficiency when proper engine configuration/calibration is used. Lastly, research that must be conducted to find the optimum combination of alcohol blends and engine configurations is highlighted and discussed.

09 BIOMASS FUELS↗
DOE OSTI2025

Enhancing EV Motor Design Through Knowledge-Based AI and Hierarchical Fuzzy Logic Model

This work presents a novel approach to optimizing electric vehicle motor design through the integration of Knowledge-Based Artificial Intelligence (KB-AI) and Hierarchical Fuzzy Logic. Traditional motor design processes are time-intensive, relying heavily on iterative simulations and domain-specific expertise. These processes are further complicated by the nonlinear relationships between key design parameters. The proposed framework addresses these challenges by systematically encoding expert knowledge from scientific literature into a fuzzy logic system, allowing for the efficient handling of complex design variables. The hierarchical fuzzy logic model reduces computational complexity by decomposing the nonlinear relationships into manageable rule sets while maintaining design accuracy. The proposed methodology was applied to the design of a 100 kW motor, yielding optimal values for key parameters. This resulted in a compact motor design with a volume of 2.2 liters, showcasing the framework’s ability to deliver high-performance, application-specific motor configurations.

Kumar, Praveen [ORNL] (ORCID:0000000291877857)↗
DOE OSTI2025

Next-Generation Electric Motors and Electromagnetic Devices (CRADA Final Report)

As part of the Cyclotron Road program, the Foli Research team investigated electric motors and other electromagnetic devices additively manufactured by depositing fine conducting wire onto a substrate. By leveraging modern motion control and efficient upstream manufacturing processes, the team explored using geometric control and turnkey production comparable to printed circuit board manufacturing, aiming at ten-fold improvements in signal density, while eliminating the material use, cost, and complexity overheads of subtractive processes at large scales. Owing to the achievable density and additive scaling, disparate components became monolithic, and disparate processes were combined with the aim of reducing development costs, uncertainties, and timelines. When applied to electric motors, this technology may enable agile manufacturing of next-generation designs, with dramatic increases in achievable power density and material utilization. Electric motors represent the single largest user of electricity in the U.S. and a critical component of decarbonized infrastructure. Despite this significance, the manufacturing of motors and other electromagnetic devices remains capital-intensive, labor-intensive, and performance-limiting. Advanced manufacturing processes were required to produce high-performance, low-cost, application-specific electric motors and electromagnetic devices to support an electrified future.

42 ENGINEERING↗
DOE OSTI2022

Fluid-powered linear motor with rotary pistons and motion rectifier and synthetic diamond bearing assemblies

A fluid-powered linear motor with rotary pistons is disclosed. An application is for a downhole motor but it could be used in other applications. Rotational pistons provide increased torque generation as the torque generated is proportional to motor length. Since downhole drills are long (generally up to a maximum length of 30 ft.), a high-torque motor can be produced using this method. A pressurized fluid is used to drive the piston assemblies to produce bit shaft power. This concept employs rotary pistons and a mechanical rectifier to convert the rotational reciprocation produced by a reciprocating rotational piston into continuous rotary motion. Integration of synthetic diamond bearing assemblies into the motor allows for reduced friction and abrasive drilling fluid compatibility.

Raymond, David W.↗
DOE OSTI2021

Design and Metamodel-Based Optimization of a High Power Density Wound Field Traction Motor

Traction motors onboard electric vehicles (EVs) are faced with ever-increasing power density requirements and cost reduction challenges. Although permanent magnet (PM) traction motors have been favored for their potential of higher power densities, the price and supply volatilities of PM materials are the major drawbacks. Instead of a single load point, the performance of a traction motor needs to be optimized over various combinations of torque and speed to represent real-world vehicular driving scenarios, which tends to be a time-consuming task with direct optimizations. In this paper, as a PM-free solution, a wound field synchronous motor (WFSM) is designed and optimized using a metamodel-based approach to maximize its efficiency over a custom set of load points, while utilizing a fully per-unitized geometry template. The workflow has proven to be timesaving and the selected design is prototyped.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Active liquid crystals powered by force-sensing DNA-motor clusters

Significance Single-molecule techniques have elucidated how isolated molecular motors generate piconewton forces with unprecedented detail. However, in diverse biological and synthetic settings, force-generating proteins collectively power nonequilibrium dynamics, including continuous large-scale rearrangements and persistent fluid flows. Characterizing motor-generated forces in these dense and dynamical environments remains a challenge. We assembled a reversible DNA-based force-sensing probe that, by an optical readout, reveals the molecular arrangements and the force loads experienced by kinesin motors. These probes provide insight into motor-generated forces that collectively power the unique dynamics of microtubule-based active nematics, a noteworthy example of an internally driven active matter system. DNA-based force probes can be extended to study forces and stresses in various synthetic systems as well as diverse cellular environments.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Comprehensive Comparative Analysis: VSI-based vs. CSI-based Motor Drive Systems with Sinusoidal Output Voltage

The emergence of wide-bandgap (WBG) power devices opens opportunities for current source inverters (CSIs) to provide a promising alternative drive configuration for motor drive applications. The sinusoidal output voltage of CSI offers significant advantages for numerous motor drive applications, including reducing the risks associated with motor terminal overvoltages and bearing discharge currents. This paper compares the performance of CSIs and voltage source inverters (VSIs) with the same performance capabilities. More specifically, sine filters are added to the VSI output terminals to match the CSI performance, and a front-end boost converter is added to the VSI to match the CSI’s voltage-boost capability. The results show that the CSI active components require 48% less volume than the VSI, combined with other performance advantages that make it an appealing candidate for some future motor drive applications.

current source inverter, motor drive system, passi↗
DOE OSTI2026

Thermal Management Solution for an Integrated Outer-Rotor Motor Drive: Opportunities and Challenges

This work highlights an integrated thermal management solution for the outer-rotor motor (ORM) drive. The integrated ORM drive utilizes water-ethylene glycol coolant for power electronics and stator cooling. Air cooling is used for rotor laminations, magnets and outer-rotor structures, and the rotor shaft. To fully understand the performance of the integrated ORM drive and thermal management coupling effects, a full drive conjugate heat transfer model has been developed to investigate coupled cooling performance of various components of the ORM drive. Various motor rotational speeds, power output scenarios, and cooling options for the integrated ORM drive have been investigated. The model estimates the operating window for the ORM drive while keeping component operating temperatures below prescribed limits. The model also highlights the importance of windage losses at higher rotational speeds for this ORM design, which involves higher rotor surface area per unit width of the rotor. Different designs are also investigated, particularly focusing on rotor cooling with air either naturally induced by rotor spin or forced airflow with the help of a blower, to circumvent challenges imposed by higher windage losses. The work highlights motor rotational speed limitations and the need for potential liquid cooling options for desired rotor performance at higher rotational speeds. Liquid cooling for the rotor may even become more critical for nonuniform rotor-stator gaps, leading to even higher and uneven windage losses across the full circumference of the motor, consequentially, more heating for the rotor.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

An Additively Manufactured Fe-3Si Stator for a High-Performance Electrical Motor

Additive manufacturing (AM) has the potential to produce novel high-performance electrical machines, enabling the direct printing of complex shapes and the simultaneous processing of multiple feedstocks in a single build. We examined the properties and functional performance of Fe-3 wt.% Si materials that were printed via selective laser melting, machined down to thin laminates, and stacked to form a stator core of a prototype brushless permanent-magnet electrical motor. Big Area Additive Manufacturing of Nd2Fe14B (NdFeB)–polyphenylene sulfide (PPS) bonded magnets was performed, with them then being magnetized and used for the rotor. The magnetic, mechanical, and electrical properties of the as-printed and various heat-treated thin laminates and the back electromotive force (EMF) of the electrical motors at different rotational speeds were measured. The thin laminates exhibit a maximum relative permeability of 7494 at an applied field of 0.8 Oe and a core loss of about 20 W/lb at 60 Hz with the maximum induction of 15 kg. In addition to the demonstration of AM printing, motor assembly, and complete characterization of printed Fe-3 wt.% Si, this report highlights the areas of improvement needed in printing technologies to achieve AM built electrical motors and the need for isotropic microstructure refinements to make the laminates appropriate for high-mechanical-strength and low-loss rotational electrical devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The Architectural Dynamics of the Bacterial Flagellar Motor Switch

The rotary bacterial flagellar motor is remarkable in biochemistry for its highly synchronized operation and amplification during switching of rotation sense. The motor is part of the flagellar basal body, a complex multi-protein assembly. Sensory and energy transduction depends on a core of six proteins that are adapted in different species to adjust torque and produce diverse switches. Motor response to chemotactic and environmental stimuli is driven by interactions of the core with small signal proteins. The initial protein interactions are propagated across a multi-subunit cytoplasmic ring to switch torque. Torque reversal triggers structural transitions in the flagellar filament to change motile behavior. Subtle variations in the core components invert or block switch operation. The mechanics of the flagellar switch have been studied with multiple approaches, from protein dynamics to single molecule and cell biophysics. The architecture, driven by recent advances in electron cryo-microscopy, is available for several species. Computational methods have correlated structure with genetic and biochemical databases. The design principles underlying the basis of switch ultra-sensitivity and its dependence on motor torque remain elusive, but tantalizing clues have emerged. This review aims to consolidate recent knowledge into a unified platform that can inspire new research strategies.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Electric Motor Thermal Management

The poster reports the accomplishments of EDT-Electric Motor Thermal Management consortium project for 2024 VTO Annual Merit Review (AMR). The overall aims of the project are to support research enabling compact, reliable, low-cost, and efficient electric machines aligned with roadmap research areas; to collaborate with ORNL, Ames, and SNL to provide motor thermal analysis support, reliability evaluation, and material measurements on related motor research at national laboratories; and collaborate with university partners including Georgia Institute of Technology and University of Wisconsin Madison to support university-led motor thermal management research efforts.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Thermal Analysis of Liquid and Air Cooling of High-Power-Density Integrated Motor Drives

Thermal management is a crucial aspect in the design of motor and drive systems. This paper introduces a coordinated cooling approach utilizing both liquid and air to enhance the integrated motor drive's power density. The proposed solution incorporates a shared water jacket to cool both the machine and power electronics, combined with forced air ventilation for the end windings and rotor. This approach is structurally simpler, less expensive, and more effective than conventional non-interacting cooling schemes. The paper addresses the modeling of key thermal features and nonlinearities including material anisotropy, contact thermal resistance, and uneven winding loss distributions. In addition, this study utilizes a more detailed model of the loss distribution among the winding turns in each slot that delivers a higher level of accuracy. Finite Element Analysis (FEA) results demonstrate the effectiveness of the integrated cooling system for efficiently cooling the designed integrated motor drive system.

42 ENGINEERING↗