Search NASA⌕ Search

SEARCH · Search NASA

Results for “multi-material physics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Surface chemistry and composition-induced variation of laser interference-based surface treatment of Al alloys

A key limitation for the use of aluminum alloys in multi-material structural components is effective surface cleaning and texturing techniques to improve the quality of structural joints. In this study, the surface and sub-surface chemistries are investigated for a novel surface treatment method using laser interferometry produced by two beams of a pulsed Nd:YAG laser. Surfaces of AA 5128 aluminum alloy were treated using a two-beam laser interference setup, enabling the structuring of the surface at length scales much less than that of the laser beam. Periodic and patterned surface structures were created by the interference power profile through ablation of deposits and debris and melting and re-solidification of the near-surface region during laser-treatment. Chemical changes to the Al alloy surface induced by laser treatment were examined in detail in this study using both x-ray photoelectron spectroscopy (XPS) and scanning Auger microanalysis (SAM) as a function of number of interfering laser shots. XPS surface analysis indicates that this laser technique is effective at cleaning aluminum surfaces. Furthermore, SAM data indicated that there is a compositional-induced variation of Mg due to laser-interference as Mg-rich areas were found in periodic interference-structured ridges.

36 MATERIALS SCIENCE↗
DOE OSTI2020

3D Cell-centered hydrodynamics with subscale closure model and multi-material remap

We extend a higher-order finite volume cell-centered hydrodynamic (CCH) formulation to include an interface-aware subscale closure model and a multi-material remap for simulating 3D compressible hydrodynamic problems within an arbitrary Lagrangian-Eulerian (ALE) framework. This CCH formulation involves a multidirectional approximate Riemann solution using quadratic polynomial reconstructions of the stress tensor and the velocity. At the subscale level, we determine pair-wise material interactions by solving a distinct approximate Riemann problem at the common interface, using the volume of fluids (VOF) method to find the interface. Material interactions are constrained to ensure smooth pressure equilibration among materials. The accuracy and robustness of the ALE method is demonstrated by simulating a suite of 3D Cartesian multi-material problems covering both gas and solid dynamics, where each test case has two or more materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

A study of adhesive bonding in metal–metal, metal–CFRP, and CFRP–CFRP material combinations under shear deformation: Fracture morphologies and damage mechanisms

Safe design of adhesive joining in multi-materials in engineered structures requires the accumulation of numerous experimental data on the failure behavior of various adhesively-bonded material combinations under different loading conditions. The deep understanding of mechanical performance, fracturing morphologies, and main damage mechanisms is also quintessential for accelerating the development of proper physics-based and multi-scale models for assisting the design. Towards this goal, this work presents a comprehensive characterization of the failure behavior of adhesively-bonded metal–metal, metal–CFRP, and CFRP–CFRP material combinations under global shear deformation via single lap shear testing. Thanks to a synergistic combination of measurement methods by using Digital Imaging Correlation (DIC) and 3D optical profilometry, adhesive features on the adherend after failure were quantified and the main progressive damage mechanisms were identified. The characterization performed in this work provides quantitative data that contributes to a better understanding of shear failure in adhesive bonding across different bi-material combinations. Finally, the obtained results have practical implications, including the potential to enhance adhesive bonding design, identify failure causes in adhesive joints, and develop or validate computational models capable of capturing the observed behavior in various adhesively-bonded materials under global shear deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Conservative remapping of material-dependent fields between possibly misaligned material regions

In this work, we propose an interpolation or remapping algorithm of material-dependent fields on polyhedral meshes where any source or target cell contains only one material. It is conservative and it preserves sharp material boundaries on the target mesh, even if the source and target regions delineating the same material are slightly misaligned. If those material regions are aligned, then the algorithm is also linearity-preserving and bounds-preserving. For a given material, it consists of a conservative field reconstruction on a target mesh part from a source mesh part associated with that material, followed by a repair step in case of misaligned boundaries. No assumption is made regarding the topology of the input meshes

36 MATERIALS SCIENCE↗
DOE OSTI2020

Volumetric analysis and mesh generation of real and artificial microstructural geometries

Producing a viable finite element mesh of realistic microstructural structural geometry is a critical step in analyzing the thermo-mechanical behavior of complex multi-material composites. Advancements in imaging technology such as micro computed tomography have allowed modelers to access high resolution mesoscale geometries for direct numerical simulation. However, converting from voxel based 3D images to usable finite element meshes has been challenging. A robust method including algorithms and software scripts for generating finite element meshes from 3D imaged microstructures is presented in this paper. It includes a routine for inserting cohesive elements around material interfaces to enable modeling of interface properties including delamination and damage. The algorithms and procedures presented in this method leverage currently available software packages for processing surface based geometry into volume based meshes. In addition to converting real geometry from physical imaging systems, algorithms for producing numerically generated and statistically equivalent microstructural geometry are also included. These artificial microstructures can be a valuable resource for modelers when physical specimens do not exist or are limited in quantity: Method establishes a workflow from voxel data to viable finite element mesh including interface information, and Includes a method for synthetic geometry generation based on metrics from real microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Surface chemistry of neutron irradiated tungsten in a high-temperature multi-material environment

Deuterium retention was measured on neutron irradiated tungsten samples where one side of the samples had a visually clean metallic luster and the opposite side appeared to have a reacted surface film. Deuterium plasma exposure and subsequent thermal desorption from the reacted surface side produced spectra with larger total deuterium desorption at lower temperatures than from the clean surface side. For neutron irradiation, these W disk samples were installed in an irradiation capsule in such a way that one side of W sample was in contact with the surface of another W sample, and the opposite side was in contact with a SiC temperature monitor. The composition of the reacted surface was investigated using X-ray photoelectron spectroscopy and showed that SiC had interdiffused into the W samples. Neutron enhanced diffusion likely contributed to this as SiC and W are stable at temperatures exceeding the irradiation temperature. Results highlight the need to consider the surface chemistry of samples in drawing conclusions on hydrogen isotope retention of W materials and also illustrate the complexity of multi-material nuclear environments expected in fusion devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Mono-material product design with bio-based, circular, and biodegradable polymers

The traditional multi-material product design of plastic products significantly complicates both existing and emerging recycling processes. Here, we discuss the concept of mono-material product design, which is based on circular and biodegradable polymers made of a single monomer, delivering tailorable properties via molecular or macromolecular engineering without changing its chemical makeup or composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Advanced supramolecular design for direct ink writing of soft materials

The exciting advancements in 3D-printing of soft materials are changing the landscape of materials development and fabrication. Among various 3D-printers that are designed for soft materials fabrication, the direct ink writing (DIW) system is particularly attractive for chemists and materials scientists due to the mild fabrication conditions, compatibility with a wide range of organic and inorganic materials, and the ease of multi-materials 3D-printing. Inks for DIW need to possess suitable viscoelastic properties to allow for smooth extrusion and be self-supportive after printing, but molecularly facilitating 3D printability to functional materials remains nontrivial. While supramolecular binding motifs have been increasingly used for 3D-printing, these inks are largely optimized empirically for DIW. Hence, this review aims to establish a clear connection between the molecular understanding of the supramolecularly bound motifs and their viscoelastic properties at bulk. Herein, extrudable (but not self-supportive) and 3D-printable (self-supportive) polymeric materials that utilize noncovalent interactions, including hydrogen bonding, host–guest inclusion, metal–ligand coordination, micro-crystallization, and van der Waals interaction, have been discussed in detail. In particular, the rheological distinctions between extrudable and 3D-printable inks have been discussed from a supramolecular design perspective. Examples shown in this review also highlight the exciting macroscale functions amplified from the molecular design. Challenges associated with the hierarchical control and characterization of supramolecularly designed DIW inks are also outlined. The perspective of utilizing supramolecular binding motifs in soft materials DIW printing has been discussed. Finally, this review serves to connect researchers across disciplines to develop innovative solutions that connect top-down 3D-printing and bottom-up supramolecular design to accelerate the development of 3D-print soft materials for a sustainable future.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Modeling atomically mixed graded density impactors

Graded density impactors (GDIs) are multi-material composite impactors used in gas gun experiments to tailor the drive conditions imparted to a sample test material. Previous graded density impactors generally rely on thin, but discrete, layers of different materials. The thinner and the greater number of layers will result in smoother compression. Taken to the limit of very thin layers would be pure material 1 at one surface, such as the front surface of an impactor, smoothly transitioning at the atomic scale to pure material 2 on the back surface. Such an impactor can initially shock, then smoothly compresses a material during a dynamic experiment. This type of experiment can serve to explore a larger region of thermodynamic space than a single or even multi-shock experiments. An overview of how graded density impactors are made is reviewed and sample results are given. Additionally, a strategy for modeling these kinds of impactors is presented. The length scales of constituent mixing are given from the experimental build through electrochemical-deposition. Equation of state models for pure constituents and their subsequent mixtures are presented. It is demonstrated that the time scales for pressure and temperature equilibration, for atomically mixed GDIs, are short enough to be a justifiable closure for the resulting multiphase flow. Furthermore, we present simulation results of dynamic shock followed by a ramp compression, utilizing a silver/gold graded density impactor, onto a tantalum sample.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Dual-energy fast neutron imaging using tunable short-pulse laser-driven sources

Here a novel dual-energy fast neutron imaging technique is presented using short-pulse laser-driven neutron sources to leverage their inherent adaptive spectral control to enable 3D volume segmentation and reconstruction. Laser-accelerated ion beams incident onto secondary targets create directional, broadband, MeV-class neutrons. Synthetic radiographs are produced of multi-material objects using ion and neutron spectra derived from analytic and numerical models. It is demonstrated that neutron images generated from small changes to the neutron spectra, controlled by altering the initial laser conditions, are sufficient to isolate materials with differing attenuation coefficients. This is first demonstrated using a simplistic combinatorial isolation method and then by employing more advanced reconstruction algorithms to reduce artifacts and generate a segmentation volume of the constituent materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Low temperature recovery of OFF-state stress induced degradation of AlGaN/GaN high electron mobility transistors

Thermal annealing is a widely used strategy to enhance semiconductor device performance. However, the process is complex for multi-material multi-layered semiconductor devices, where thermoelastic stresses from lattice constant and thermal expansion coefficient mismatch may create more defects than those annealed. We propose an alternate low temperature annealing technique, which utilizes the electron wind force (EWF) induced by small duty cycle high density pulsed current. To demonstrate its effectiveness, we intentionally degrade AlGaN/GaN high electron mobility transistors (HEMTs) with accelerated OFF-state stressing to increase ON-resistance ∼182.08% and reduce drain saturation current ∼85.82% of pristine condition at a gate voltage of 0 V. We then performed the EWF annealing to recover the corresponding values back to ∼122.21% and ∼93.10%, respectively. The peak transconductance, degraded to ∼76.58% of pristine at the drain voltage of 3 V, was also recovered back to ∼92.38%. This recovery of previously degraded transport properties is attributed to approximately 80% recovery of carrier mobility, which occurs during EWF annealing. We performed synchrotron differential aperture x-ray microscopy measurements to correlate these annealing effects with the lattice structural changes. We found a reduction of lattice plane spacing of (001) planes and stress within the GaN layer under the gate region after EWF annealing, suggesting a corresponding decrease in defect density. Application of this low-temperature annealing technique for in-operando recovery of degraded electronic devices is discussed.

Physics↗
DOE OSTI2021

Material migration in W and Mo during bubble growth and fuzz formation

Growth of helium (He) induced bubbles and fuzz in tungsten (W) and molybdenum (Mo) is investigated using samples of W films on Mo substrates and Mo films on W substrates exposed to He-containing plasma in the temperature range of 340 to 1075 K, fluence range of 1.0–14 × 10 25 He·m -2 , and incident ion energy of <50 eV. No fuzz (only up to 2 nm diameter bubbles) and no material transport occur in W films at ≤750 K, while precursors-of or fully-developed fuzz and material mixing occur in W and Mo films at ≥800 K. This suggests that fuzz forms in multi-material systems as long as one material meets the conditions for fuzz formation, namely T s / T m ~ 0.27–0.5 where T s and T m are the sample exposure and material melting temperatures, respectively. Larger He bubbles, more material mixing, and further-developed fuzz occur at higher temperature due to increased mobility of He atoms and small He clusters. Accumulation of substrate material at the surface of fuzzy W and Mo thin-film (<80 nm) samples suggests fuzz growth by material transport from the bubble layer in the bulk up to the fiber tip, likely by a two-step process: (i) diffusion of punched dislocation loops in the bulk toward the fuzz base and (ii) diffusion of adatoms along the fuzz base and fiber surface (with effective transport of adatoms upwards due to trapping of adatoms at curved surfaces of fiber tips and/or due to the continuous generation of adatoms at the fuzz base). While the bubble size and fuzz thickness increase with reduced W concentration in Mo thin-film samples at 838 K likely due to an increase in trap mutation and dislocation loop punching in Mo compared to W, the fuzz thickness decreases with reduced W concentration at 1075 K despite an increase in the bubble size likely due to slower diffusion of interstitial loops in Mo.

Physics↗
DOE OSTI2020

UNR ETI Computational Investigation (Year 2)

The LANL ASC Arbitrary Lagrange/Eulerian (ALE) code, FLAG, is being used to model experiments conducted under this grant in order to understand the physics limiting high-current conduction and thermal plasma production. This includes the effects of nonlinear magnetic diffusion (NLMD), the magnetic Rayleigh-Taylor (MRT) instability, and the electro-thermal instability (ETI). FLAG is a multi-dimensional, unstructured-grid, multi-material, multi-temperature, shockphysics code with a single-fluid, resistive magnetohydrodynamics (MHD) package. Equations-ofstate (EOS), conductivity, material-strength, and melt can be treated with a variety of analytic or tabular models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Tardigrade (Quarterly Report Q1 FY2022)

Tardigrade is an effort to create tunable thermal expansion materials for use in a ruggedized lens housing. This requires new computational algorithms to model and predict thermal performance of meta-materials composed of multiple structured base materials and void-space, along with matching and developing 3D print technology to demonstrate the housing. The project is 27 months into the 36-month plan. We are continuing effort on 3 main technical thrusts: material design algorithm development (transitioning into full 3D design), multi-material additive manufacturing process exploration, and sensor/optics design and engineering. In the last quarter, we have focused on developing the code for 3D Topology Optimization, building data sets for 2D autoencoder training, and finishing lens housing engineering for the microbolometer based test sensor. We are exploring 2 potential multi-material AM technologies, a polymer-based technique in development at LLNL and a metal SLS system produced by Aconity, called the AeroSint deposition head.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Self-Consistent Relativistic Electron Scattering using the Sherlock Scattering Model for X-ray Diagnostics

We present on a new, self-consistent, arbitrary-temperature Romberg integration scheme for modeling electron scattering in materials in a LANL Lagrangian Shock Hydro (LSH) code. Electron beam-target interactions are fundamental to a wide range of scientific and technological applications. When high-energy electron beams hit their target, they may scatter, deposit energy, or ionize the source. These processes govern the behavior and outcomes in nanotechnology manufacturing, electron microscopy, and modern X-ray diagnostics. Simulating these interactions is essential for interpreting experimental results, predicting material responses, and designing efficient tools and experiments. At Los Alamos, this is done using a LSH code, which is a multi-dimension, multi-material, massively parallel, multi-physics code used to simulate applications from asteroid impacts to electron beam interactions. By effectively and efficiently modeling the way that electrons scatter from the beam we can bolster these simulations and more accurately predict experimental outcomes. The model currently implemented in the LSH of interest is based on work by Papp and does not self-consistently preserve momentum in the slightly relativistic regime; here we adopt a model proposed by Braams and Karney and implement a Romberg integration scheme to compute the diffusion tensor. In this paper we will provide background on the Braams-Karney diffusion tensor as well as the Romberg integration scheme we employed to numerically solve for it. We will show that our integration scheme is accurate in solving for the set of scalar potentials used to re-express the diffusion tensor in differential form, and in solving for the diffusion coefficients in the larger LSH code. By using this diffusion tensor rather than the existing Papp one, and numerically integrating it with a Romberg method, we produce much more accurate, self-consistent results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Variation in surface properties as error sources in dynamic temperature measurements

Most temperature measurement methods rely upon the assumption of a single uniform source as part of the analysis in inferring an observed temperature T from the surface of a material. This is true for the radiometric and spectroscopic methods we rely upon in shock physics. However, there are obvious cases where this is a poor assumption that can cause large errors in analysis, such as the measurement of emission from a surface composed of more than one material, such as a rusted surface of Fe and Fe 2 O 3 , or a multi-material surface that could be produced through alloying methods (e.g., mokume gane) or 3D printing. Here we perform an initial examination of the effects of varied surface properties upon the analysis using idealized test data to constrain when we may have better confidence in the resulting calculations. We also examine the structures of the fits to test whether, in principle, comparing the fit with ideal gray bodies would reveal such a structure and enable the researcher to identify when a two-temperature fitting model should be used instead of a single- T model or a wavelength-dependent emissivity model.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Review on Progress, Challenges, and Prospects of Material Jetting of Copper and Tungsten

Copper (Cu) and tungsten (W) possess exceptional electrical and thermal conductivity properties, making them suitable candidates for applications such as interconnects and thermal conductivity enhancements. Solution-based additive manufacturing (SBAM) offers unique advantages, including patterning capabilities, cost-effectiveness, and scalability among the various methods for manufacturing Cu and W-based films and structures. In particular, SBAM material jetting techniques, such as inkjet printing (IJP), direct ink writing (DIW), and aerosol jet printing (AJP), present a promising approach for design freedom, low material wastes, and versatility as either stand-alone printers or integrated with powder bed-based metal additive manufacturing (MAM). Thus, this review summarizes recent advancements in solution-processed Cu and W, focusing on IJP, DIW, and AJP techniques. The discussion encompasses general aspects, current status, challenges, and recent research highlights. Furthermore, this paper addresses integrating material jetting techniques with powder bed-based MAM to fabricate functional alloys and multi-material structures. Finally, the factors influencing large-scale fabrication and potential prospects in this area are explored.

36 MATERIALS SCIENCE↗
NASA NTRS2011

ARC+(Registered Trademark) and ARC PC Welding Simulators: Teach Welders with Virtual Interactive 3D Technologies

123 Certification Inc., a Montreal based company, has developed an innovative hands-on welding simulator solution to help build the welding workforce in the most simple way. The solution lies in virtual reality technology, which has been fully tested since the early 90's. President and founder of 123 Certification Inc., Mr. Claude Choquet Ing. Msc. IWE. acts as a bridge between the welding and the programming world. Working in these fields for more than 20 years. he has filed 12 patents world-wide for a gesture control platform with leading edge hardware related to simulation. In the summer of 2006. Mr Choquet was proud to be invited to the annual IIW International Weld ing Congress in Quebec City to launch the ARC+ welding simulator. A 100% virtual reality system and web based training center was developed to simulate multi process. multi-materiaL multi-position and multi pass welding. The simulator is intended to train welding students and apprentices in schools or industries. The welding simulator is composed of a real welding e[eetrode holder (SMAW-GTAW) and gun (GMAW-FCAW). a head mounted display (HMD), a 6 degrees of freedom tracking system for interaction between the user's hands and head. as well as external audio speakers. Both guns and HMD are interacting online and simultaneously. The welding simulation is based on the law of physics and empirical results from detailed analysis of a series of welding tests based on industrial applications tested over the last 20 years. The simulation runs in real-time, using a local logic network to determine the quality and shape of the created weld. These results are based on the orientation distance. and speed of the welding torch and depth of penetration. The welding process and resulting weld bc.1d are displayed in a virtual environment with screenplay interactive training modules. For review. weld quality and recorded process values can be displayed and diagnosed after welding. To help in the le.tming process, a learning curve for each student and each Virtual Welding Class'" can be plotted, for an instructor's review or a required third party evaluation.

Choquet, Claude↗