Search NASA⌕ Search

SEARCH · Search NASA

Results for “nonlinear model reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Projection and assembly method for multibody component model reduction

The problem addressed is that of obtaining reduced-order component models for use in simulating the dynamics of a multibody system. In certain cases, nonlinear system models may be constructed using linear dynamic models for each component, but allowing large angle motion between components. Without some form of model reduction, system models constructed in this manner may be too large for use in control system design and simulation trades. This paper analyzes one method of component model reduction that allows systems level requirements (e.g., capturing the effect of body 1 reaction wheel noise on body 2 camera pointing) to aid in the selection of the reduced-order component models. Briefly stated, important modes are selected at the system level and projected onto the components, and reduced-order components are then assembled into a reduced-order system model that retains the projected modes.

Bernard, Douglas E.↗
NASA NTRS1984

Linear distributed parameter systems - Closed-loop exponential stability with a finite-dimensional controller

Theoretical results are presented which characterize the linear distributed parameter system (DPS) which can be (exponentially) stabilized by a finite-dimensional controller. This characterization relies on stabilizing subspaces and the solvability of the nonlinear asymmetric Riccati equation. Also considered are connections with the usual model reduction approaches to finite-dimensional DPS controller design.

Balas, M. J.↗
NASA NTRS1987

Nonlinear transient analysis of joint dominated structures

A residual force technique is presented that can perform the transient analyses of large, flexible, and joint dominated structures. The technique permits substantial size reduction in the number of degrees of freedom describing the nonlinear structural models and can account for such nonlinear joint phenomena as free-play and hysteresis. In general, joints can have arbitrary force-state map representations but these are used in the form of residual force maps. One essential feature of the technique is to replace the arbitrary force-state maps describing the nonlinear joints with residual force maps describing the truss links. The main advantage of this replacement is that the incrementally small relative displacements and velocities across a joint are not monitored directly thereby avoiding numerical difficulties. Instead, very small and 'soft' residual forces are defined giving a numerically attractive form for the equations of motion and thereby permitting numerically stable integration algorithms. The technique was successfully applied to the transient analyses of a large 58 bay, 60 meter truss having nonlinear joints. A method to perform link testing is also presented.

Chapman, J. M.↗
NASA NTRS1984

Fitting aerodynamic forces in the Laplace domain: An application of a nonlinear nongradient technique to multilevel constrained optimization

A technique which employs both linear and nonlinear methods in a multilevel optimization structure to best approximate generalized unsteady aerodynamic forces for arbitrary motion is described. Optimum selection of free parameters is made in a rational function approximation of the aerodynamic forces in the Laplace domain such that a best fit is obtained, in a least squares sense, to tabular data for purely oscillatory motion. The multilevel structure and the corresponding formulation of the objective models are presented which separate the reduction of the fit error into linear and nonlinear problems, thus enabling the use of linear methods where practical. Certain equality and inequality constraints that may be imposed are identified; a brief description of the nongradient, nonlinear optimizer which is used is given; and results which illustrate application of the method are presented.

Tiffany, S. H.↗
DOE OSTI2025

Perturbative model for the saturation of energetic-particle-driven modes limited by self-generated zonal modes

We present a simplified energy-conserving approach to incorporate wave–wave nonlinear effects within the framework commonly used to describe wave–particle nonlinearities. In particular, the effects of zonal mode (ZM) generation on the determination of the saturation amplitude of energetic particle (EP)-driven Alfvénic instabilities is studied. The model assumes that the zonal perturbations grow at a rate twice that of the original (pump) wave, consistent with a beat-driven (or force-driven) generation mechanism. The evolution and saturation of the mode amplitude are investigated both analytically and numerically within our reduced model assumptions, in both the collisionless and scattering-dominated regimes. These studies underscore the crucial role of sources and sinks in capturing the impact and the role of beat-driven zonal perturbations on mode evolution. In the realistic case of saturation set by sources and sinks, we discuss the role of a finite amplitude ZM in reducing microturbulent particle scattering, thus limiting the energy source for the resonant mode. We then discuss comparisons between the model’s predictions and simulation results. The model reproduces key features observed in gyrokinetic simulations as the reduction in saturated mode amplitude and the onset of wave–wave nonlinear effects as functions of mode growth rate and amplitude. Thanks to its simplicity, it can be readily implemented into codes based on reduced models, thereby improving their predictive capability for strongly driven instabilities.

Alfvén eigenmodes↗
NASA NTRS1988

Combined mechanical loading of composite tubes

An analytical/experimental investigation was performed to study the effect of material nonlinearities on the response of composite tubes subjected to combined axial and torsional loading. The effect of residual stresses on subsequent mechanical response was included in the investigation. Experiments were performed on P75/934 graphite-epoxy tubes with a stacking sequence of (15/0/ + or - 10/0/ -15), using pure torsion and combined axial/torsional loading. In the presence of residual stresses, the analytical model predicted a reduction in the initial shear modulus. Experimentally, coupling between axial loading and shear strain was observed in laminated tubes under combined loading. The phenomenon was predicted by the nonlinear analytical model. The experimentally observed linear limit of the global shear response was found to correspond to the analytically predicted first ply failure. Further, the failure of the tubes was found to be path dependent above a critical load level.

Derstine, Mark S.↗
NASA NTRS1978

Procedures for generation and reduction of linear models of a turbofan engine

A real time hybrid simulation of the Pratt & Whitney F100-PW-F100 turbofan engine was used for linear-model generation. The linear models were used to analyze the effect of disturbances about an operating point on the dynamic performance of the engine. A procedure that disturbs, samples, and records the state and control variables was developed. For large systems, such as the F100 engine, the state vector is large and may contain high-frequency information not required for control. This, reducing the full-state to a reduced-order model may be a practicable approach to simplifying the control design. A reduction technique was developed to generate reduced-order models. Selected linear and nonlinear output responses to exhaust-nozzle area and main-burner fuel flow disturbances are presented for comparison.

Seldner, K.↗
NASA NTRS1983

Alternatives for jet engine control

Tensor model order reduction, recursive tensor model identification, input design for tensor model identification, software development for nonlinear feedback control laws based upon tensors, and development of the CATNAP software package for tensor modeling, identification and simulation were studied. The last of these are discussed.

Sain, M. K.↗
DOE OSTI2024

Physics-Informed Active Learning With Simultaneous Weak-Form Latent Space Dynamics Identification

The parametric greedy latent space dynamics identification (gLaSDI) framework has demonstrated promising potential for accurate and efficient modeling of high-dimensional nonlinear physical systems. However, it remains challenging to handle noisy data. Here, to enhance robustness against noise, we incorporate the weak-form estimation of nonlinear dynamics (WENDy) into gLaSDI. In the proposed weak-form gLaSDI (WgLaSDI) framework, an autoencoder and WENDy are trained simultaneously to discover intrinsic nonlinear latent-space dynamics of high-dimensional data. Compared with the standard sparse identification of nonlinear dynamics (SINDy) employed in gLaSDI, WENDy enables variance reduction and robust latent space discovery, therefore leading to more accurate and efficient reduced-order modeling. Furthermore, the greedy physics-informed active learning in WgLaSDI enables adaptive sampling of optimal training data on the fly for enhanced modeling accuracy. The effectiveness of the proposed framework is demonstrated by modeling various nonlinear dynamical problems, including viscous and inviscid Burgers' equations, time-dependent radial advection, and the Vlasov equation for plasma physics. With data that contains 5%–10% Gaussian white noise, WgLaSDI outperforms gLaSDI by orders of magnitude, achieving 1%–7% relative errors. Compared with the high-fidelity models, WgLaSDI achieves 121 to 1779x speed-up.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Weak-Form Latent Space Dynamics Identification

This software showcases the enhanced capabilities of the Latent Space Dynamics Identification (LaSDI) algorithm through the application of the weak form, resulting in WLaSDI. WLaSDI first compresses the data, then projects it onto test functions, and subsequently learns the local latent space models. Notably, WLaSDI demonstrates significantly improved robustness to noise. Using weak-form equation learning techniques, WLaSDI achieves local latent space modeling. Compared to the standard sparse identification of nonlinear dynamics (SINDy) used in LaSDI, the variance reduction of the weak form ensures robust and precise latent space recovery, enabling fast, robust, and accurate simulations. We demonstrate the efficacy of WLaSDI against LaSDI using several common benchmark examples, including viscid and inviscid Burgers', radial advection, and heat conduction. For instance, in 1D inviscid Burgers' simulations with up to 100% Gaussian white noise, WLaSDI maintains relative errors consistently below 6%, whereas LaSDI errors can exceed 10,000%. Similarly, in radial advection simulations, WLaSDI keeps relative errors below 16%, compared to potential errors of up to 10,000% with LaSDI. Additionally, WLaSDI achieves significant speedups, such as a 140X speedup in 1D Burgers' simulations compared to the corresponding full order model.

Choi, Youngsoo↗
NASA NTRS1993

Drag reduction in channel flow using nonlinear control

Two nonlinear control schemes have been applied to the problem of drag reduction in channel flow. Both schemes have been tested using numerical simulations at a mass flux Reynolds numbers of 4408, utilizing 2D nonlinear neutral modes for goal dynamics. The OGY-method, which requires feedback, reduces drag to 60-80 percent of the turbulent value at the same Reynolds number, and employs forcing only within a thin region near the wall. The H-method, or model-based control, fails to achieve any drag reduction when starting from a fully turbulent initial condition, but shows potential for suppressing or retarding laminar-to-turbulent transition by imposing instead a transition to a low drag, nonlinear traveling wave solution to the Navier-Stokes equation. The drag in this state corresponds to that achieved by the OGY-method. Model-based control requires no feedback, but in experiments to date has required the forcing be imposed within a thicker layer than the OGY-method. Control energy expenditures in both methods are small, representing less than 0.1 percent of the uncontrolled flow's energy.

Keefe, Laurence R.↗
NASA NTRS1989

Breakdown of vertically propagating two-dimensional gravity waves forced by orography

The propagation of orographic gravity waves into an atmosphere with exponentially decreasing density is simulated with a two-dimensional, nonlinear, time-dependent numerical model. After the stationary wave is established over the mountain, the model predicts that wave breaking causes a large reduction of the vertical momentum flux in the flow, not only at levels where wave breaking is present, but also far below the lowest occurrence of overturning. More than half of the decrease in momentum flux is explained by the presence of large amplitude, downward propagating waves, which are generated in regions of wave breaking. The downward propagating waves appear almost simultaneously with overturning, and have nonzero phase speeds, suggesting a strongly nonlinear generation mechanism that depends on local wave properties. The generation of these downward propagating waves is a robust process, insensitive to mountain height, mountain width, or density scale height. These results have important implications for observational studies of orographically generated waves as well as for schemes that seek to parameterize the effects of orogoraphy in large-scale models.

Bacmeister, Julio T.↗
NASA NTRS1993

Model reduction in integrated controls-structures design

It is the objective of this paper to present a model reduction technique developed for the integrated controls-structures design of flexible structures. Integrated controls-structures design problems are typically posed as nonlinear mathematical programming problems, where the design variables consist of both structural and control parameters. In the solution process, both structural and control design variables are constantly changing; therefore, the dynamic characteristics of the structure are also changing. This presents a problem in obtaining a reduced-order model for active control design and analysis which will be valid for all design points within the design space. In other words, the frequency and number of the significant modes of the structure (modes that should be included) may vary considerably throughout the design process. This is also true as the locations and/or masses of the sensors and actuators change. Moreover, since the number of design evaluations in the integrated design process could easily run into thousands, any feasible order-reduction method should not require model reduction analysis at every design iteration. In this paper a novel and efficient technique for model reduction in the integrated controls-structures design process, which addresses these issues, is presented.

Maghami, Peiman G.↗
DOE OSTI2025

Heterogeneous Mixtures of Dictionary Functions to Approximate Subspace Invariance in Koopman Operators: Why Deep Koopman Operators Work

Abstract Koopman operators model nonlinear dynamics as a linear dynamic system acting on a nonlinear function as the state. This nonstandard state is often called a Koopman observable and is usually approximated numerically by a superposition of functions drawn from a dictionary . In a widely used algorithm, extended dynamic mode decomposition (EDMD), the dictionary functions are drawn from a fixed class of functions. Deep learning combined with EDMD has been used to learn novel dictionary functions in an algorithm called deep dynamic mode decomposition (deepDMD). The learned representation both (1) accurately models and (2) scales well with the dimension of the original nonlinear system. In this paper, we analyze the learned dictionaries from deepDMD and explore the theoretical basis for their strong performance. We explore State-Inclusive Logistic Lifting (SILL) dictionary functions to approximate Koopman observables. Error analysis of these dictionary functions show they satisfy a property of subspace approximation, which we define as uniform finite approximate closure. Typically, a Koopman dictionary’s nonlinear functions are homogeneous. In this paper, we discover that structured mixing of heterogeneous dictionary functions drawn from different classes of nonlinear functions achieve the same accuracy and dimensional scaling as the deep-learning-based deepDMD algorithm Yeung et al. ( In: 2019 American Control Conference (ACC), 2019). We specifically show this by building a heterogeneous dictionary comprised of SILL functions and conjunctive radial basis functions (RBFs). This mixed dictionary achieves similar accuracy and dimensional scaling to deepDMD with an order of magnitude reduction in parameters, while maintaining geometric interpretability. These results strengthen the viability of dictionary-based Koopman models to solving high-dimensional nonlinear learning problems.

Johnson, Charles A.↗
NASA NTRS1983

Evaluation of the effect of vibration nonlinearity on convergence behavior of adaptive higher harmonic controllers

Effect of nonlinearity on convergence of the local linear and global linear adaptive controllers is evaluated. A nonlinear helicopter vibration model is selected for the evaluation which has sufficient nonlinearity, including multiple minimum, to assess the vibration reduction capability of the adaptive controllers. The adaptive control algorithms are based upon a linear transfer matrix assumption and the presence of nonlinearity has a significant effect on algorithm behavior. Simulation results are presented which demonstrate the importance of the caution property in the global linear controller. Caution is represented by a time varying rate weighting term in the local linear controller and this improves the algorithm convergence. Nonlinearity in some cases causes Kalman filter divergence. Two forms of the Kalman filter covariance equation are investigated.

Molusis, J. A.↗
NASA NTRS2001

Data Reduction and Its Impact on Test-Analysis Correlation

A research project has been initiated to improve crash test and analysis correlation. The research has focused on two specimen types: simple metallic beams and plates; and a representative composite fuselage section. Impact tests were performed under carefully controlled conditions. In addition, the specimens were densely instrumented to enable not only correlation with finite element simulations, but to also assess the repeatability of the data. Simulations utilizing a detailed finite element model were executed in a nonlinear transient dynamic code. The results presented in this paper concentrate on the effect of several data reduction processes, to include filtering frequency and sampling rate, on the correlation accuracy.

Lyle, Karen H.↗
NASA NTRS1995

An approximate Kalman filter for ocean data assimilation: An example with an idealized Gulf Stream model

A practical method of data assimilation for use with large, nonlinear, ocean general circulation models is explored. A Kalman filter based on approximation of the state error covariance matrix is presented, employing a reduction of the effective model dimension, the error's asymptotic steady state limit, and a time-invariant linearization of the dynamic model for the error integration. The approximations lead to dramatic computational savings in applying estimation theory to large complex systems. We examine the utility of the approximate filter in assimilating different measurement types using a twin experiment of an idealized Gulf Stream. A nonlinear primitive equation model of an unstable east-west jet is studied with a state dimension exceeding 170,000 elements. Assimilation of various pseudomeasurements are examined, including velocity, density, and volume transport at localized arrays and realistic distributions of satellite altimetry and acoustic tomography observations. Results are compared in terms of their effects on the accuracies of the estimation. The approximate filter is shown to outperform an empirical nudging scheme used in a previous study. The examples demonstrate that useful approximate estimation errors can be computed in a practical manner for general circulation models.

Fukumori, Ichiro↗
NASA NTRS1994

An Approximate Kalman Filter for Ocean Data Assimilation; An Example with an Idealized Gulf Stream Model

A practical method of data assimilation for use with large, nonlinear, ocean general circulation models is explored. A Kalman filter based on approximations of the state error covariance matrix is presented, employing a reduction of the effective model dimension, the error's asymptotic steady-state limit, and a time-invariant linearization of the dynamic model for the error integration. The approximations lead to dramatic computational savings in applying estimation theory to large complex systems. We examine the utility of the approximate filter in assimilating different measurement types using a twin experiment of an idealized Gulf Stream. A nonlinear primitive equation model of an unstable east-west jet is studied with a state dimension exceeding 170,000 elements. Assimilation of various pseudo measurements is examined, including velocity, density, and volume transport at localized arrays, and realistic distributions of satellite altimetry and acoustic tomography observations. Results are compared in terms of their effects on the accuracies of the estimation. The approximate filter is shown to outperform a previous study that used an empirical nudging scheme. The examples demonstrate that useful approximate estimation errors can be computed in a practical manner for general circulation models.

['Kalman↗