Search NASA⌕ Search

SEARCH · Search NASA

Results for “nuclear fuel processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Development of an L-Edge X-ray Absorbance Spectrometer for Monitoring Dissolver Solutions in H-Canyon

Savannah River National Laboratory has developed a monitor to measure plutonium and uranium concentrations in solutions of dissolved nuclear fuel. The monitor will be installed in the sample aisle location for the 6.3D Dissolver in the Savannah River Site’s H-Canyon and used in support of the electrolytic dissolution such as Fast Critical Assembly fuel. The monitor is based on the atomic absorbance of x-rays. Elements are differentiated by the appearance of absorbance features at specific energies of the x-ray spectrum that correspond to L-edge transitions of inner core electrons. Hence, the technique is called L-Edge X-Ray Absorbance Spectroscopy (L-XRAS). The technique is suitable for nuclear fuel processing due to its relative insensitivity to other components of the dissolver solution, such as nitric acid, transition metals (Fe, Cr, Ni, Mn) such as those from stainless steel, particulates, and catalysts and additives. The instrumentation consists of a commercially available x-ray source and detector, a sample cell designed to interface with the airlift sampler associated with H-Canyon Tank 6.3D, and a stainless steel enclosure. SRNL wrote instrument control software and developed chemometric models to interpret x-ray intensity spectra and estimate analyte concentrations and uncertainties in real time.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Covalency in Actinide Compounds

Covalency in actinides has emerged as a resounding research topic on account of the technological importance in separating minor actinides from lanthanides for spent nuclear fuel processing, and utilization of their distinct bonding properties has been realized as a route towards overcoming this challenge. Because of the limited radial extent of the 4f orbitals, there is almost no 4f electron participation in bonding in lanthanides; this is not the case for the actinides, which have extended 5f orbitals that are capable of overlapping with ligand orbitals, although not to the degree of overlap as in the d orbitals of transition metals. In this concept paper, we provide a general description of covalency in actinide compounds. After introducing two main approaches to enhance covalency, either by exploiting increased orbital overlap or decreasing energy differences between the orbitals causing orbital energy degeneracy, we show the current state of the field using several examples from the recent literature. Here, we will conclude by proposing the use of actinide chalcogenides as a convenient auxiliary tool to study covalency in actinide compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Pronounced Pressure Dependence of Electronic Transitions for Americium Compared to Isomorphous Neodymium and Samarium Mellitates

The mellitate ion is relevant in spent nuclear fuel processing and is utilized as a surrogate for studying the interactions of f elements with humic acids. A wealth of different coordination modes gives the potential for diverse structural chemistry across the actinide series. In this study, an americium mellitate, 243 Am 2 [(C 6 (COO – ) 6 ](H 2 O) 8 ·2H 2 O (1-Am), has been synthesized and characterized using structural analysis and spectroscopy at ambient and elevated pressures. 1-Am was then compared to isomorphous neodymium (1-Nd) and samarium (1-Sm) mellitates via bond-length analysis and pressure dependence of their Laporte-forbidden f → f transitions. Results show that the pressure dependence of the f → f transitions of 1-Am is significantly greater than that observed in 1-Nd and 1-Sm, with average shifts of 21.4, 4.7, and 3.6 cm –1 /GPa, respectively. Finally, this greater shift found in 1-Am shows further evidence that the 5f orbitals are more affected than the 4f orbitals when pressure is applied to isostructural compounds.

Actinides↗
DOE OSTI2022

An Overview in the Development of a Multi-Sensor Data Science System for Monitoring a Solvent Extraction Process

To enhance nuclear nonproliferation stewardship, Idaho National Laboratory is building the Beartooth nuclear fuel cycle processing test bed. The Beartooth test bed will allow researchers the opportunity to study nuclear fuel processing operations including the use of centrifugal contactors in solvent extraction processes. The test bed is designed to support data collection and machine learning to monitor process operations. As part of this project, researchers will study data collected from a host of sensors that have not been typically used to monitor solvent extraction processes such as vibration, acoustic, colormetric, and thermal measurement data. The goal of this research is to employ machine learning and data analytics to study the confluence of signals collected from both traditionally and non-traditionally used sensors to provide operator process awareness and discover process anomalies. An overview of planned sensors and experiments that will focus on signal discovery will be presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

An Overview in the Development of a Multi-Sensor Data Science System for Monitoring a Solvent Extraction Process

To enhance nuclear nonproliferation stewardship, Idaho National Laboratory is building the Beartooth nuclear fuel cycle processing test bed. The Beartooth test bed will allow researchers the opportunity to study nuclear fuel processing operations including the use of centrifugal contactors in solvent extraction processes. The test bed is designed to support data collection and machine learning to monitor process operations. As part of this project, researchers will study data collected from a host of sensors that have not been typically used to monitor solvent extraction processes such as vibration, acoustic, colormetric, and thermal measurement data. The goal of this research is to employ machine learning and data analytics to study the confluence of signals collected from both traditionally and non-traditionally used sensors to provide operator process awareness and discover process anomalies. An overview of planned sensors and experiments that will focus on signal discovery will be presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Phosphate-Based Approaches for Dechlorination and Treatment of Salt Waste from Electrochemical Processing of Used Nuclear Fuel: A Perspective on Recent Work

Phosphate-based reagents are being considered by the U.S. Department of Energy (DOE) Office of Nuclear Energy to process halide salt-based nuclear wastes for stabilization prior to disposal. As evidenced by the Experimental Breeder Reactor-II (EBR-II) project, electrochemical processing (pyroprocessing) can be employed to recover uranium and other actinides for reintegration into the nuclear fuel cycle from metallic fuels. The resultant salt-based wastes generated from electrochemical processing of EBR-II fuel contains fission products within a LiCl–KCl eutectic salt that necessitate appropriate disposal. This paper provides an overview of recent efforts to support halide-based salt waste treatment for disposition, as well as a basis for comparison with other related efforts in salt waste treatment through salt partitioning initiatives. The U.S. DOE has selected a phosphate waste form reference material for further investigation and longer-term studies.

electrorefiner↗
DOE OSTI2026

A Coincident CdTe Detector Array for Enhanced Nuclear Process Monitoring

Nuclear fuel cycle aqueous separation processes desire improved real-time material characterization and process monitoring techniques; gamma coincidence spectroscopy has the potential to meet this need in these high throughput and high radiation environments based on its ability to reduce background noise, thereby enhancing detection limits and improving isotopic identification accuracy. A detector array composed of three CdTe detectors was designed to surround a chemical processing pipe in a reprocessing facility and evaluate the feasibility of passively assaying the nuclear materials flowing though this measurement point. This array uses commercial off the shelf components that are radiation hard and highly efficiency at low energies relevant to actinide photon signatures. Detector efficiency characterizations, coincidence detection, and potential configuration improvements are presented here.

Good, Erin C.↗
DOE OSTI2022

Multi-Sensor Data Acquisition System for Process Monitoring

Idaho National Laboratory is building a new nuclear fuel cycle test bed. This fuel cycle test bed named “Beartooth” will give researchers the opportunity to study the nuclear fuel cycle process. The process operations include the use of centrifugal contactors and process flow for the purification of special nuclear material recovery in used fuel. This new research facility has the need to use non-traditional measurement sensors to determine the state-of-health of the solvent extraction process. These non-traditional sensors can also enhance nuclear nonproliferation supervision and other activities. The non-traditional sensors include accelerometers, acoustic, current, flow, colorimetric, temperature, pH and conductivity. The challenge behind deploying all these sensors, is the need for fast and reliable data collection. The data acquisition system (DAQ) needs to be capable of recording up to 12 accelerometers and/or acoustic microphones simultaneously at rates up to 12.8 kSamples/second/channel. This requires the need for a strong architecture and data collection solution. This summary identifies the system architecture, DAQ, and sensors needed to support non-traditional measurements in a solvent extraction process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Development of a Nuclear Fuel Dissolution Monitor Based on Raman Spectroscopy

The processing of spent nuclear fuel and other nuclear materials is a critical component of nuclear material management with implications for global security. The first step of fuel processing is dissolution, with several charges of fuel sequentially added to a batch of solvent. The incomplete dissolution of a charge precludes the addition of the next charge. As the dissolution takes place in a heated, highly corrosive and radiological vessel, direct monitoring of the process is not possible. We discuss the use of Raman spectroscopy to indirectly monitor dissolution through an analysis of the gaseous emissions from the dissolver. Challenges associated with the implementation of Raman spectroscopy include the composition and physical characteristics of the offgas stream and the impact of operating conditions. Nonetheless, we observed that NO2 concentrations serve as a reliable indicator of process activity and correlate to the amount of fuel material that remains undissolved. These results demonstrate the promise of the method for monitoring nuclear material dissolution.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Update on Full-Scale Retrieval and Transfer System Testing for Pneumatic Conveyance of High-Level Calcine Waste - 20241

The Idaho National Laboratory processed spent nuclear fuel from 1953 to 1994. The process used solvent extraction to separate uranium, resulting in a liquid waste. A calcination process was used to convert the liquid waste to a high-level radioactive solid powder, referred to as calcine. The calcine is stored in stainless steel bins contained within concrete vaults called the Calcined Solids Storage Facilities. There are a total of seven CSSFs. The Calcine Retrieval Project is tasked with retrieving the calcine from the bins of CSSF 1 and pneumatically transferring it to the bins of CSSF 6. CSSF 1 was constructed to be a final calcine repository with no forethought of retrieval. It represents the greatest technical hurdle to calcine extraction of all the CSSFs. The challenges inherent with accessing the calcine, safely extracting it, and securely transporting it are copious and complex. Once the calcine is removed from CSSF1, that facility may be closed, reducing the footprint of waste storage at the INL. The same process for removing Calcine from CSSF1 may then be utilized to remove the calcine from the remaining CSSFs for final treatment and transport to a long-term storage facility. To overcome these inherent challenges with accessing CSSF 1 and extracting the calcine in a timely manner, a full-scale integrated mockup has been constructed. The mockup includes a full-size model of a concentric group of bins from CSSF 1 and a storage vessel representing CSSF 6. All essential elements of the transport design are represented in the Mockup, including motive and makeup air supply (air compressor), a replica of the CSSF6 cyclone, pre-filter, HEPA filter, vacuum pump, and retrieval control devices. Construction on the Mockup was completed in 2018 and testing began in February 2019. It has already proven very beneficial to the CRP. Experience in running the Mockup have aided in the development of retrieval and transport methodologies and the selection of process parameter values. It has also uncovered some unforeseen technological challenges and will continue to be valuable to the testing team as these hurdles are overcome and the process is proven effective. Operations personnel have also benefitted from its use as a training tool and will continue to use the Mockup as a simulator to reproduce problems encountered during extraction and transfer of Calcine from CSSF 1. The knowledge gained during this process will also be of continued benefit as future work is done to remove various types of calcine from the remaining CSSFs. The methodology of safe and secure transfer of radioactive material may be of benefit to others throughout the U.S. Department of Energy complex. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

MPACT Safeguards Modeling: FY25 Update

Sandia National Laboratories develops and maintains several open-source software packages to support material accountancy analyses. This includes the Material Accountancy Performance Indicator Toolkit (MAPIT), the Fissile Facility Flow Modeler (F3M) and the Separation and Safeguards Performance Model Library (SSPM-L). MAPIT is responsible for performing statistical safeguards analyses on bulk and itemized data from nuclear fuel cycle facilities and can operate on real or synthetic data. MAPIT is the only open-source software for such analyses. F3M is a library of modules, built in MATLAB Simulink, that contain pre made blocks to represent different generic fuel cycle processes. These blocks can be used together in a modular fashion to represent and simulate nuclear fuel cycle processes with the goal of improving facility-level accountancy during the design phase. F3M is also an open-source library. Finally, the SSPM-L library is a series of completed models built from F3M. The library includes facility models such as a generic PUREX facility and a fuel fabrication facility. The SSPM-L library is not open source, but is available to collaborators with a relevant use case. These tools include modeling and simulation pipelines to simulate nuclear fuel cycle facilities and the underlying software needed to simulate measurement uncertainty and perform statistical analyses. Together, these tools can perform end-to-end nuclear material accountancy analyses. This report documents the various improvements made to these tools in FY25. Specifically, we added new statistical test, new statistical modeling capabilities, new fuel cycle facility models, and launched a new open-source model component library.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Isotopic Characterization of HALEU from EBR-II Driver Fuel Processing

Provide the isotopic characteristics of the High Assay Low Enriched Uranium (HALEU) product recovered during the used nuclear fuel treatment operations occurring at Idaho National Laboratory. Revision one of this document (TEV-3537 Rev 1) provides isotopic characterization for material that has been recast using the drip cast crucible gravity casting technique used to transform traditional EBR-II uranium ingots into regulus.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗