SEARCH · Search NASA
Results for “numerics”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An Experimental and Numerical Investigation to Characterize the Low-Temperature Heat Release in Stoichiometric and Lean Combustion
This work reports on an experimental and modeling study on the low-temperature heat release (LTHR) characteristics for three RON 90 binary blends (n-heptane blended with isooctane, toluene and ethanol) in a Cooperative Fuel Research (CFR) engine at lean and stoichiometric conditions that are representative of homogeneous charge compression ignition (HCCI) and spark-ignition (SI) end-gas combustion conditions, respectively. An analysis of the end-gas temperature-pressure (T-P) trajectories was performed to identify the intake conditions leading to similar T-P trajectories between the two lambdas for each fuel blend. A heat release analysis was then conducted for the identified cases, where fuel-to-fuel differences in LTHR were identified and found to be sensitive to the operating condition. Simulations were conducted for these cases using a recently updated chemical kinetic model and a 0-D engine model, where good qualitative and reasonable quantitative agreements in LTHR were obtained. Sensitivity analysis was also performed directly on the rates of LTHR, to understand the controlling chemical reactions of LTHR, providing further insights into the fuel-to-fuel differences. The results demonstrate the significant promoting effect of n-heptane on LTHR rates, while inhibiting effects were seen for ethanol and toluene. Also highlighted was the importance of H atom abstraction reactions from the chemistry of each fuel component, which could lead to contradictory fuel behavior depending on the locations of the H site of the abstraction reaction due to the different ensuing pathways for the primary fuel radicals.
Numerical simulation of the hot-tail runaway electron production mechanism using CQL3D and comparison with Smith–Verwichte analytical model
Abstract The hot-tail mechanism of runaway electron (RE) production (Harvey et al 2000 Phys. Plasmas 7 4590) is the primary source of RE in the case of rapidly cooling tokamak plasma. Quantifying this mechanism is very important as it can provide most of the post-thermal-quench (TQ) current, or a seed current for the secondary source of RE through the avalanche mechanism. An analytic model which omits pitch-angle scattering is often used in literature for estimating the hot-tail RE density (Smith and Verwichte 2008 Phys. Plasmas 15 072502). In the present study, we use the CQL3D bounce-averaged Fokker–Planck code (Harvey and McCoy 1992 Proc. IAEA Technical Committee Meeting on Advances in Simulation and Modeling of Thermonuclear Plasmas p 527) to test the limits of validity of the model. In particular, we examine the cases of Z = 1 and Z = 18 ions, for sets of different initial temperature, density, electric field and the characteristic time of temperature decay. We show that for Z = 1 plasma, the ratio of RE density computed by CQL3D to that estimated from the model is within 0.6–6.0 in studied cases. For the Z = 18 case, this factor is systematically a much smaller number, typically 0.02–0.6. We suggest a simple correction to the model that narrows down the range of this ratio to 0.3–3.8 in all of the cases, including Z = 1 and Z = 18 plasmas.
Experimental and Numerical Investigation of a Miniature Additively Manufactured Vortex Tube
Ranque–Hilsch vortex tubes are simple devices that can produce a cooling effect using compressed air. A key advantage of vortex tubes is the lack of moving solid parts; however, their efficiencies are relatively low. The present study focuses on the development of a miniature variable-diameter tube using additive manufacturing. A metal-based 3D printing technique was utilized to fabricate this vortex tube monolithically. Computational fluid dynamics simulations employing software STAR-CCM + with a compressible Reynolds-Averaged Navier–Stokes (RANS) approach and the elliptic-blending lag k-epsilon turbulence model have been applied to model thermofluid processes inside the vortex tube, to good agreement with the experiment. In conclusion, a temperature decrease of 13.3 °C and a cooling power of approximately 4 W were experimentally achieved with a pressure ratio of 4 in the air at normal conditions. This result shows promise for the goal of utilizing additive manufacturing to design and build complex-geometry vortex tubes intended for use with cryogenic fluids.
Estimates of Southern Hemispheric Gravity Wave Momentum Fluxes across Observations, Reanalyses, and Kilometer-Scale Numerical Weather Prediction Model
Abstract Gravity waves (GWs) are among the key drivers of the meridional overturning circulation in the mesosphere and upper stratosphere. Their representation in climate models suffers from insufficient resolution and limited observational constraints on their parameterizations. This obscures assessments of middle atmospheric circulation changes in a changing climate. This study presents a comprehensive analysis of stratospheric GW activity above and downstream of the Andes from 1 to 15 August 2019, with special focus on GW representation ranging from an unprecedented kilometer-scale global forecast model (1.4 km ECMWF IFS), ground-based Rayleigh lidar (CORAL) observations, modern reanalysis (ERA5), to a coarse-resolution climate model (EMAC). Resolved vertical flux of zonal GW momentum (GWMF) is found to be stronger by a factor of at least 2–2.5 in IFS compared to ERA5. Compared to resolved GWMF in IFS, parameterizations in ERA5 and EMAC continue to inaccurately generate excessive GWMF poleward of 60°S, yielding prominent differences between resolved and parameterized GWMFs. A like-to-like validation of GW profiles in IFS and ERA5 reveals similar wave structures. Still, even at ∼1 km resolution, the resolved waves in IFS are weaker than those observed by lidar. Further, GWMF estimates across datasets reveal that temperature-based proxies, based on midfrequency approximations for linear GWs, overestimate GWMF due to simplifications and uncertainties in GW wavelength estimation from data. Overall, the analysis provides GWMF benchmarks for parameterization validation and calls for three-dimensional GW parameterizations, better upper-boundary treatment, and vertical resolution increases commensurate with increases in horizontal resolution in models, for a more realistic GW analysis. Significance Statement Gravity wave–induced momentum forcing forms a key component of the middle atmospheric circulation. However, complete knowledge of gravity waves, their atmospheric effects, and their long-term trends are obscured due to limited global observations, and the inability of current climate models to fully resolve them. This study combines a kilometer-scale forecast model, modern reanalysis, and a coarse-resolution climate model to first compare the resolved and parameterized momentum fluxes by gravity waves generated over the Andes, and then evaluate the fluxes using a state-of-the-art ground-based Rayleigh lidar. Our analysis reveals shortcomings in current model parameterizations of gravity waves in the middle atmosphere and highlights the sensitivity of the estimated flux to the formulation used.
Experimental and Numerical Study on the Effect of Nitric Oxide on Autoignition and Knock in a Direct-Injection Spark-Ignition Engine
We report Nitric Oxide (NO) can significantly influence the autoignition reactivity and this can affect knock limits in conventional stoichiometric SI engines. Previous studies also revealed that the role of NO changes with fuel type. Fuels with high RON (Research Octane Number) and high Octane Sensitivity (S = RON – MON (Motor Octane Number)) exhibited monotonically retarding knocklimited combustion phasing (KL-CA50) with increasing NO. In contrast, for a high-RON, low-S fuel, the addition of NO initially resulted in a strongly retarded KL-CA50 but beyond the certain amount of NO, KL-CA50 advanced again. The current study focuses on same high-RON, low-S Alkylate fuel to better understand the mechanisms responsible for the reversal in the effect of NO on KLCA50 beyond a certain amount of NO. Experiments were conducted to measure the responses of KL-CA50 and trace-autoignition CA50, the latter being indicative of CA50 at which end-gas autoignition starts to become measurable from the apparent heat-release rate. Chemical-kinetics simulations were conducted to reveal the role of NO for end-gas autoignition, with a specific focus on sequential autoignition in a thermally stratified end-gas. The simulation results reveal that the magnitude of low-temperature heat release (LTHR) generally increases with NO. However, the relative importance of NO for enhancing LTHR diminishes when the LTHR inherent to a fuel’s chemistry is strong, such as at lower temperatures in a thermal boundary layer. This rendered more uniform LTHR within a hypothetical thermal boundary and led to a more sequential (i.e. slower) autoignition event. It was also revealed that a change in compression ratio influences the importance of intermediate-temperature heat release (ITHR) due to changes of the temperature-pressure history of the end-gas. Together with the condition where end-gas autoignition occurs more sequentially, the shorter time spent in LTHR and ITHR regime can counter the increase in autoignition reactivity at high NO levels and allow KLCA50 to advance
Investigation of Numerical Schemes for Direct Numerical Simulations of Supersonic Turbulent Boundary Layers
No abstract available
Testing GPU Numerics: Finding Numerical Differences Between NVIDIA and AMD GPUs
Explore the source record for details and available documents.
The Analysis and Design of Low Boom Configurations Using CFD and Numerical Optimization Techniques
The use of computational fluid dynamics (CFD) for the analysis of sonic booms generated by aircraft has been shown to increase the accuracy and reliability of predictions. CFD takes into account important three-dimensional and nonlinear effects that are generally neglected by modified linear theory (MLT) methods. Up to the present time, CFD methods have been primarily used for analysis or prediction. Some investigators have used CFD to impact the design of low boom configurations using trial and error methods. One investigator developed a hybrid design method using a combination of Modified Linear Theory (e.g. F-functions) and CFD to provide equivalent area due to lift driven by a numerical optimizer to redesign or modify an existing configuration to achieve a shaped sonic boom signature. A three-dimensional design methodology has not yet been developed that completely uses nonlinear methods or CFD. Constrained numerical optimization techniques have existed for some time. Many of these methods use gradients to search for the minimum of a specified objective function subject to a variety of design variable bounds, linear and nonlinear constraints. Gradient based design optimization methods require the determination of the objective function gradients with respect to each of the design variables. These optimization methods are efficient and work well if the gradients can be obtained analytically. If analytical gradients are not available, the objective gradients or derivatives with respect to the design variables must be obtained numerically. To obtain numerical gradients, say, for 10 design variables, might require anywhere from 10 to 20 objective function evaluations. Typically, 5-10 global iterations of the optimizer are required to minimize the objective function. In terms of using CFD as a design optimization tool, the numerical evaluation of gradients can require anywhere from 100 to 200 CFD computations per design for only 10 design variables. If one CFD computation requires an hour of computational time on a Cray computer, one can see that the use of constrained numerical optimization quickly becomes impractical.Hence, in order to practically couple a numerical design optimization technique with a CFD method, the CFD method must be extremely efficient with running times on the order of only minutes. The CFD Euler code developed under NASA sponsorship and referred to as MIM3D-SB for the most part fulfills these efficiency requirements. Analysis of wing- body configurations can be computed in a matter of a few minutes. The present study will concentrate on the feasibility of the use of this CFD code in conjunction with a numerical design optimization technique for the sonic boom reduction of candidate HSCT configurations. A preliminary supersonic aircraft design system has been established that utilizes the numerical design optimization code NPSOL developed at Stanford University coupled with the supersonic NUM3D-SB CFD code. Many questions still need to be answered in regard to using CFD and numerical optimizers as design tools. There are difficulties related to both the CFD codes and the numerical optimizers. Numerical optimizers can converge to a local minima rather than a global minima. This behavior is largely a function of the initial guess in the design space. The optimizer also is searching for a minimum of the function in terms of its derivative without any regard to the actual function value. Numerically (i.e. CFD) determined gradients can also generate spurious numerical local minima. In addition, for the sonic boom problem, grid fineness will also determine the accuracy of the final design solution. Design optimization methods work well on problems defined by continuous objective functions. The sonic boom signature design problem is not necessarily defined by a continuous objective function. The signature can have a variety of shapes; i.e. from N-wave to multiple shocks. The far-field or ground signature may not transition continuously from one shape to another and hence, may exhibit discontinuous behavior. This is also a source of difficulty in using design optimization methods.In the following sections, several low boom and one reference aircraft configuration will be analyzed to predict their sonic boom signature characteristics. Modifications to some of these designs will also be presented to demonstrate the feasibility of using CFD as a design tool and to demonstrate the feasibility of designing shaped sonic boom signatures. Design modifications to some configurations will be presented to demonstrate the feasibility of achieving shaped signatures with reduced levels and not necessarily to represent realistic or aerodynamically efficient design modifications. Fuselage volume or camber are used as design variables in order to have a minimal effect on the primary wing aerodynamics. The paper will also seek to demonstrate whether a hybrid or ramped signature is feasible to achieve. For the low-boom configurations, the CFD predicted signatures will be compared qualitatively to their MLT design signatures.
Computational general relativistic force-free electrodynamics: II. Characterization of numerical diffusivity
Scientific codes are an indispensable link between theory and experiment; in (astro-)plasma physics, such numerical tools are one window into the universe’s most extreme flows of energy. The discretization of Maxwell’s equations – needed to make highly magnetized (astro)physical plasma amenable to its numerical modeling – introduces numerical diffusion. It acts as a source of dissipation independent of the system’s physical constituents. Understanding the numerical diffusion of scientific codes is the key to classifying their reliability. It gives specific limits in which the results of numerical experiments are physical. We aim at quantifying and characterizing the numerical diffusion properties of our recently developed numerical tool for the simulation of general relativistic force-free electrodynamics by calibrating and comparing it with other strategies found in the literature. Our code correctly models smooth waves of highly magnetized plasma. We evaluate the limits of general relativistic force-free electrodynamics in the context of current sheets and tearing mode instabilities. We identify that the current parallel to the magnetic field (j ∥ ), in combination with the breakdown of general relativistic force-free electrodynamics across current sheets, impairs the physical modeling of resistive instabilities. We find that at least eight numerical cells per characteristic size of interest (e.g., the wavelength in plasma waves or the transverse width of a current sheet) are needed to find consistency between resistivity of numerical and of physical origins. High-order discretization of the force-free current allows us to provide almost ideal orders of convergence for (smooth) plasma wave dynamics. The physical modeling of resistive layers requires suitable current prescriptions or a sub-grid modeling for the evolution of j ∥ .
A simple and effective five-equation two-phase numerical model for liquid-vapor phase transition in cavitating flows
Numerical difficulties, notably the non-monotonic behavior of the Wood speed of sound and the volume fraction positivity, associated with the reduced five-equation two-phase flow model of Kapila et al. (2001) [A.K. Kapila, R. Menikoff, J.B. Bdzil, S.F. Son, D.S. Stewart, 2001. Two-phase modeling of deflagration-to-detonation transition in granular materials: reduced equations, Physics of Fluids 13(10), 3002–3024] have been resolved in the past through the introduction of a frozen speed of sound and an algebraic approach for mechanical relaxation afforded by a pressure non-equilibrium six-equation model proposed by [R. Saurel, F. Petitpas, R.A. Berry, 2009. Simple and efficient relaxation methods for interfaces separating compressible fluids, cavitating flows and shocks in multiphase mixture, J. Comput. Phys. 228, 1678–1712]. By contrast, it is explored and demonstrated in this work that these difficulties can in fact still be resolved within the numerical scheme for solving the reduced five-equation model by numerically replacing the Wood speed of sound for the estimates of wave speeds in the approximate Riemann solver HLLC with the monotonic mixture speed of sound for a transport five-equation model. For shock interface (artificial mixture separating pure or nearly pure fluids) interaction problems, with the apparent advantage of monotonic behavior of the speed of sound in the interface, the effect of the numerical replacement is also confined to the interface. Differences other than the behavior of the speed of sound within the interface in the solutions due to the replacement diminish with increasing resolution when reasonable solution can be obtained with Wood speed of sound. For cavitating/expansion problems in physical fluid mixture, it is pointed out and explained why acoustics in the numerical solutions still propagate at the Wood speed of sound (therefore consistent with the reduced five-equation model) even though in some cases a much higher speed of sound like the numerical replacement above for solving the reduced five-equation model or the frozen speed of sound for solving a six-equation model is used for the estimates of wave speeds in the HLLC scheme. A variant of the five-equation two-phase flow model by Saurel et al. (2008) [R. Saurel, F. Petitpas, R. Abgrall, 2008. Modelling phase transition in metastable liquids: application to cavitating and flashing flows, J. Fluid Mech. 607, 313–350] is then constructed for liquid-vapor phase transition in cavitating flows. The relaxation toward thermo-chemical equilibrium during phase transition is achieved by solving a simple system of algebraic equations for the equilibrium state variables for better efficiency, following Pelanti and Shyue (2014) [M. Pelanti, K.-M. Shyue, 2014. A mixture-energy-consistent six-equation two-phase numerical model for fluid with interfaces, cavitation and evaporation waves. J. Comput. Phys. 259, 331–357]. Therefore, the current model retains both the simplicity afforded by the five-equation model and the efficiency of the algebraic relaxation solver. An alternative algebraic approach for handling the non-conservative term (the so-called K∇ · u term) in the reduced five-equation model for mechanical equilibrium of a liquid-vapor mixture is also explored by enforcing the thermal equilibrium at the same time. Finally, numerical results of sample tests in both one and two dimensions in the literature as well as that in three dimensions demonstrate the effectiveness and ability of the proposed model to simulate cavitating flows. An interesting mechanism of shock generation by acoustics in water due to phase transition is then found by the numerical simulations.
Quantification of Physical and Numerical Mixing in a Coastal Ocean Model Using Salinity Variance Budgets
Numerical mixing, the spurious mixing primarily generated by the discretization of advection, is often significant in estuarine and coastal models due to sharp, energetic fronts. In this study, we compare on- and offline estimates of numerical mixing in a submesoscale-resolving realistic simulation of the ocean state over the Texas-Louisiana continental shelf. While offline estimates of numerical mixing differ from online estimates, offline methods may be the only analysis available. This study offers insight into the differences between the on- and offline methods. We use two methods to estimate numerical mixing offline, based on salinity squared $s^2$ and volume-mean salinity variance $s^{\prime^2}$. Numerical mixing estimated from the $s^{\prime^2}$ budget is generally within 60\% of the magnitude for the online method but captures the temporal variability well. However, the $s^2$ budget compares poorly due to larger truncation errors associated with the tendency and advection terms, which can be reduced by increasing the model output frequency. We also investigate the effects of horizontal resolution on numerical mixing using a two-way nested grid. The volume-integrated numerical mixing constitutes 57\% of the bulk physical mixing -- the mixing prescribed by the turbulence closure scheme -- in the coarse model and may exceed the physical mixing by half an order of magnitude. We find that numerical mixing is reduced by 35\% on average in the nested model, less than expected based on scaling of the numerical mixing for an upwind advection scheme, likely due to new dynamical processes that emerge in the nested simulation.
An Evaluation of Size-Resolved Cloud Microphysics Scheme Numerics for use with Radar Observations Part II: Condensation and Evaporation
Accurate numerical modeling of clouds and precipitation is essential for weather forecasting and climate change research. While size-resolved (bin) cloud microphysics models predict particle size distributions without imposing shapes, results are subject to artificial size distribution broadening owing to numerical diffusion associated with various processes. Whereas Part 1 addressed collision-coalescence, here we investigate numerical diffusion that occurs in solving condensation and evaporation. In a parcel model framework, all of the numerical schemes examined converge to one solution of condensation and evaporation as the mass grid is refined, and the advection-based schemes are recommended over the reassigning schemes. Including Eulerian vertical advection in a column limits the convergence to some extent, but that limitation occurs at a sufficiently fine mass grid, and the number of iterations in solving vertical advection should be minimized to reduce numerical diffusion. Insubstantial numerical diffusion in solving condensation can be amplified if collision-coalescence is also active, which in turn can be substantially diminished if turbulence effects on collision are incorporated. Large-eddy simulations of a drizzling stratocumulus field reveal that changes in moments of Doppler spectra obtained using different mass grids are consistent with those obtained from the simplified framework, and that spectral moments obtained using a mass grid designed to effectively reduce numerical diffusion are generally closer to observations. Notable differences between the simulations and observations still exist, and our results suggest a need to consider whether factors other than numerical diffusion in the fundamental process schemes employed can cause such differences.
Machine Learned Empirical Numerical Integrator from Simulated Data
Recently, a number of state-of-the-art surrogate machine learning (ML) models have been designed for global weather and climate prediction, which have been trained using reanalysis data products. Reanalysis data products are constructed using numerical model simulations that combine numerical integration of partial differential equations and parameterization schemes. These products are typically only archived and made available using coarsened spatial and temporal resolutions. This study explores the impact of the numerical generation methods used to produce the training datasets and the temporal resolution of those datasets on machine learning surrogate models. Using the nonlinear vector autoregression (NVAR) machine as an explainable ML technique, simple dynamical systems are emulated with ML models trained on data produced by three classical numerical integration schemes. NVAR is validated as a skillful ML method, capable of producing accurate predictions and, more importantly, reconstructing both the underlying dynamics and the numerical integration scheme used to generate the training data. However, the machine fails to generalize predictions on unseen test data generated by different numerical integration schemes, despite the underlying dynamical system being the same. This result provides a word of caution for the growing field of machine learning emulation of weather and climate dynamics. Furthermore, we illustrate using NVAR that training on temporally coarsened data may increase the required complexity of ML models and potentially introduce new numerical challenges. Finally, we discover that empirical integration schemes with arbitrary time-stepping sizes can be constructed directly from the data, which implies a potential for the development of empirical numerical integration schemes.