Search NASA⌕ Search

SEARCH · Search NASA

Results for “on-board estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

On-board communication for active-control transport aircraft

An investigation of active control communications sponsored by the NASA Langley Research Center is summarized. Particular attention is given to comparative architectures, for which a common set of requirements is generated as a baseline. Most of the requirements are aircraft functional in nature, such as stability and command augmentation, structural load relief, flight path control, flight control linkage, flight monitoring, management, navigation, engine control, and ground communication; the time element, the hazard environment, and the communications capacity estimation are also important factors. The architectures involve several communication technologies, including dedicated links, broadcast busing, and multiplex busing. The multiplex bus system provides the greatest flexibility and installation efficiency. A future homogeneous network system is also proposed, which would be fault and damage tolerant and would, with advanced technology, avoid the problems of designing a very large and flight critical multiplex bus system.

Brock, L. D.↗

Maximum likelihood failure detection techniques applied to the shuttle orbiter reaction control subsystem

A technique for on-board detection and identification of hard failures and leaks of the shuttle orbiter reaction control subsystem jets, during the orbital flight phase, is presented. The method uses gimbal angle and linear accelerometer measurements from the orbiter inertial measurement unit and requires no additional hardware. Extended Kalman filters with residual traps are employed for state estimation, and generalized likelihood ratio tests for jet failure identification. Rigid body simulation results indicate identification times of less than 2 seconds for hard jet failures and less than 70 seconds for jet leaks.

Deckert, J. C.↗

Dust distribution of Comet Halley from the Giotto radio science experiment

Measurements from the Giotto radio science experiment representing the Doppler frequency shift and the intensity level of the X-band downlink signal of the Giotto spacecraft during its encounter with comet Halley are shown. Continuous data reception was maintained throughout the encounter. The Doppler shift measured within a time interval of 100 sec is due to drag effects in the cometary atmosphere causing a deceleration of the spacecraft. The total change of velocity of Giotto is 23.2 cm/sec resulting in a best estimate of 0.32 g for the total cometary mass impacting Giotto during the Halley flyby. A dust jet structure for the inner coma of comet Halley is derived. Several sharply confined dust jets are distinguishable; for the most prominent one, characteristic properties are deduced. Features of this jet structure are shown to correlate with measurements from on-board Giotto experiments and with Earth-based observations.

Edenhofer, P.↗

F-8C adaptive control law refinement and software development

An explicit adaptive control algorithm based on maximum likelihood estimation of parameters was designed. To avoid iterative calculations, the algorithm uses parallel channels of Kalman filters operating at fixed locations in parameter space. This algorithm was implemented in NASA/DFRC's Remotely Augmented Vehicle (RAV) facility. Real-time sensor outputs (rate gyro, accelerometer, surface position) are telemetered to a ground computer which sends new gain values to an on-board system. Ground test data and flight records were used to establish design values of noise statistics and to verify the ground-based adaptive software.

Hartmann, G. L.↗

Navigation simulator for the Space Tug vehicle

A general simulation program (GSP) for state estimation of a nonlinear space vehicle flight navigation system is developed and used as a basis for evaluating the performance of a Space Tug navigation system. An explanation of the iterative guidance mode (IGM) guidance law, derivation of the dynamics, coordinate frames and state estimation routines are given in order to clarify the assumptions and approximations made. A number of simulation and analytical studies are used to demonstrate the operation of the Tug system. Included in the simulation studies are (1) initial offset vector parameter study; (2) propagation time vs accuracy; (3) measurement noise parametric study and (4) reduction in computational burden of an on-board implementable scheme. From the results of these studies, conclusions and recommendations concerning future areas of practical and theoretical work are presented.

Colburn, B. K.↗

Recovery of thrust magnitude from minitrack data for the SERT-2 spacecraft

An estimation of the thrust magnitude of the Space Electric Rocket Test (SERT) engine is obtained. This estimation is based on changes in the SERT-2 spacecraft orbit as determined from tracking data by using a revised definitive orbit determination system which includes the effect of thrust upon the motion of a spacecraft in general and the SERT-2 satellite in particular. The results of these computations are found to be in good agreement with values of acceleration as determined by an on-board accelerometer. A discussion of the mathematical model used to obtain the numerical results is also presented.

Jones, E. M.↗

Processing on-board optical data for planetary approach navigation.

The Mariner 9 spacecraft's science television camera provided an optical navigation experiment with TV pictures containing images of Mars' natural satellites against star backgrounds. Required TV image data and spacecraft engineering data were extracted from the spacecraft telemetry stream in this near-real time experiment designed to validate the navigation content of spacecraft-based optical data. This paper discusses the computer programs developed to prepare optical data for use in a navigation filter. Ground and in-flight calibration allowed pointing knowledge of better than 6 arc seconds. System performance during Mars approach was excellent, leading to extremely accurate trajectory estimates. The experiment provides a basis for the design of equivalent systems for future missions.

Acton, C. H., Jr.↗

Digital adaptive controllers for VTOL vehicles. Volume 1: Concept evaluation

A digital self-adaptive flight control system was developed for flight test in the VTOL approach and landing technology (VALT) research aircraft (a modified CH-47 helicopter). The control laws accept commands from an automatic on-board guidance system. The primary objective of the control laws is to provide good command-following with a minimum cross-axis response. Three attitudes and vertical velocity are separately commanded. Adaptation of the control laws is based on information from rate and attitude gyros and a vertical velocity measurement. The final design resulted from a comparison of two different adaptive concepts--one based on explicit parameter estimates from a real-time maximum-likelihood estimation algorithm, the other based on an implicit model reference adaptive system. The two designs were compared on the basis of performance and complexity.

Hartmann, G. L.↗

Flight data processing with the F-8 adaptive algorithm

An explicit adaptive control algorithm based on maximum likelihood estimation of parameters has been designed for NASA's DFBW F-8 aircraft. To avoid iterative calculations, the algorithm uses parallel channels of Kalman filters operating at fixed locations in parameter space. This algorithm has been implemented in NASA/DFRC's Remotely Augmented Vehicle (RAV) facility. Real-time sensor outputs (rate gyro, accelerometer and surface position) are telemetered to a ground computer which sends new gain values to an on-board system. Ground test data and flight records were used to establish design values of noise statistics and to verify the ground-based adaptive software. The software and its performance evaluation based on flight data are described

Hartmann, G.↗

Equations and approximations involved in computing vertical wind velocities from superpressure balloon data

Superpressure, or constant-level, balloons have long been used to obtain horizontal wind velocities in the atmosphere. This paper presents equations which can be used to evaluate omega, the vertical wind component in pressure coordinates, from on-board pressure and temperature sensors. These equations take into account the short-term displacements of a balloon from its equilibrium density level, and thus they do not assume that the balloon precisely maintains constant density. The longer-term and larger-amplitude diurnal oscillations in balloon level, and also an approximation used in deriving the vertical velocity equations, are both discussed in some detail. These equations can be used to obtain quantitative estimates of omega if reasonable estimates of the ambient lapse rate could be obtained.

Banta, R. M.↗

On the determination and investigation of the terrestrial ionospheric refractive indices using GEOS-3/ATS-6 satellite-to-satellite tracking data

When the radio link between two satellites (GEOS-3/ATS-6) is intercepted by the earth's ionosphere and neutral atmosphere, a change in the Doppler frequency results. Travel through the atmosphere causes the Doppler phase to be advanced in the ionosphere's portion and retarded in the neutral portion of the atmosphere. Analysis of the shortening and lengthening of the phase of the Satellite-to-Satellite Tracking (SST) data that passed within 40-700 km above the earth's surface during its ATS-6 to GEOS-3 to ATS-6 path, caused by the atmosphere, results in refractivity versus height profiles. The SST Doppler data were used directly to adjust the GEOS-3 orbit. Perturbation from the Moon, Sun and a 15th order/degree earth gravity field were included in the orbit solution. This orbit was continued through the occultation period and a model ionosphere was estimated by a least-square adjustment of the Chapman ionosphere parameters from the SST data residuals. The refractivity profile obtained by this model ionosphere was compared to a refractivity profile obtained by a direct integral inversion of the SST data residuals. Systematic differences between the 2 methods were caused by orbital errors, which propagated into the solution. The SST data yielded refractive index profiles in a novel economical manner because no additional or special on-board equipment were required.

Liu, A. S.↗

Terminal guidance and navigation for comet and asteroid rendezvous

A terminal guidance and navigation scheme developed in earlier work was modified and evaluated for a solar electric propulsion rendezvous mission to comet Encke. The scheme is intended for autonomous, on-board use. The guidance algorithm is based on optimal control theory and minimizes the time integrated square of thrust acceleration. The navigation algorithm employs a modified Kalman filter set in measurement variables. Random sequences were generated to simulate measurement errors, and the evaluation was conducted with detailed numerical computations which include actual motions of spacecraft and comet. The evaluations showed that the scheme attains rendezvous and maintains station after rendezvous within less than 10 km for estimated best measurements and within less than 100 km for estimated worst measurements. The measurements required are angles, range, and range rate. Angles and range appear to be absolutely necessary; range rate is not as strong a measurement type, and further modifications of the filter will allow a scheme that does not require the rate measurements.

Bennett, A. G.↗

ATS-1/ATS-3 dual satellite navigation study

A study which illustrated the feasibility of implementing an on-board aircraft navigation system based on using the ATS-1 and ATS-3 satellites, the modified Omega Position Location Equipment (OPLE) Control Center, and a suitable aircraft terminal was conducted. The report provides: (1) a consideration of the problems of satellite navigation and an objective definition of the optimum system under the constraints of its specified components, (2) a description of the necessary modifications to the OPLE Control Center, the design of an aircraft terminal, and the design of ground reference terminals, and (3) an outline of an experiment plan and an estimate of the cost to be expected in conducting the program.

Hoover, W. M.↗

On-board processing satellite network architecture and control study

The market for telecommunications services needs to be segmented into user classes having similar transmission requirements and hence similar network architectures. Use of the following transmission architecture was considered: satellite switched TDMA; TDMA up, TDM down; scanning (hopping) beam TDMA; FDMA up, TDM down; satellite switched MF/TDMA; and switching Hub earth stations with double hop transmission. A candidate network architecture will be selected that: comprises multiple access subnetworks optimized for each user; interconnects the subnetworks by means of a baseband processor; and optimizes the marriage of interconnection and access techniques. An overall network control architecture will be provided that will serve the needs of the baseband and satellite switched RF interconnected subnetworks. The results of the studies shall be used to identify elements of network architecture and control that require the greatest degree of technology development to realize an operational system. This will be specified in terms of: requirements of the enabling technology; difference from the current available technology; and estimate of the development requirements needed to achieve an operational system. The results obtained for each of these tasks are presented.

Campanella, S. Joseph↗

On-board processing satellite network architecture and control study

For satellites to remain a vital part of future national and international communications, system concepts that use their inherent advantages to the fullest must be created. Network architectures that take maximum advantage of satellites equipped with onboard processing are explored. Satellite generations must accommodate various services for which satellites constitute the preferred vehicle of delivery. Such services tend to be those that are widely dispersed and present thin to medium loads to the system. Typical systems considered are thin and medium route telephony, maritime, land and aeronautical radio, VSAT data, low bit rate video teleconferencing, and high bit rate broadcast of high definition video. Delivery of services by TDMA and FDMA multiplexing techniques and combinations of the two for individual and mixed service types are studied. The possibilities offered by onboard circuit switched and packet switched architectures are examined and the results strongly support a preference for the latter. A detailed design architecture encompassing the onboard packet switch and its control, the related demand assigned TDMA burst structures, and destination packet protocols for routing traffic are presented. Fundamental onboard hardware requirements comprising speed, memory size, chip count, and power are estimated. The study concludes with identification of key enabling technologies and identifies a plan to develop a POC model.

Campanella, S. Joseph↗

On-board processing for future satellite communications systems: Satellite-Routed FDMA

A frequency division multiple access (FDMA) 30/20 GHz satellite communications architecture without on-board baseband processing is investigated. Conceptual system designs are suggested for domestic traffic models totaling 4 Gb/s of customer premises service (CPS) traffic and 6 Gb/s of trunking traffic. Emphasis is given to the CPS portion of the system which includes thousands of earth terminals with digital traffic ranging from a single 64 kb/s voice channel to hundreds of channels of voice, data, and video with an aggregate data rate of 33 Mb/s. A unique regional design concept that effectively smooths the non-uniform traffic distribution and greatly simplifies the satellite design is employed. The satellite antenna system forms thirty-two 0.33 deg beam on both the uplinks and the downlinks in one design. In another design matched to a traffic model with more dispersed users, there are twenty-four 0.33 deg beams and twenty-one 0.7 deg beams. Detailed system design techniques show that a single satellite producing approximately 5 kW of dc power is capable of handling at least 75% of the postulated traffic. A detailed cost model of the ground segment and estimated system costs based on current information from manufacturers are presented.

Berk, G.↗

Systematic uncertainties in the measurement of the neutron lifetime using the Lunar Prospector neutron spectrometer

The lifetime of free neutrons measured in the laboratory has a longstanding disparity of ≈9 s. A space-based technique has recently been proposed to independently measure the neutron lifetime using interactions between the galactic cosmic rays and a low atmosphere planetary body. This technique has not produced competitive results yet due to constraints of nonoptimized data that contain large systematic errors. We use data from the neutron spectrometer on-board NASA's Lunar Prospector, and study two large systematics in the measurement of neutron lifetime: the lunar subsurface temperature and the lunar surface composition. We use the HeCd and HeSn neutron spectrometer data when the spacecraft was in a highly elliptical orbit during the orbit insertion period. We report the neutron lifetime using four different models that each have different choices of surface temperature and composition. The 5° [Prettyman et al ., J. Geophys. Res.: Planets 111, 2005JE002656 (2006)] and 2° [Wilson et al., Phys. Rev. C 104, 045501 (2021)] rebinned maps result in 777.6±11.7 s and 739.6±10.8 s, respectively. For the 20° map (Prettyman et al., 2006), constant equatorial and a latitude-dependent temperature model result in 738.6±10.8 s and 767.3±11.2 s, respectively. Increasing the complexities of the models accounting for the systematic effects increase the measured lifetime. However, the reported measurements are not competitive with the laboratory results due to large unaccounted systematics resulting from nonoptimized measurements and modeling assumptions. This work serves as a study of systematic uncertainties for future neutron lifetime measurements using the space-based technique. We estimate the effect on the lifetime from the choice of temperature model to be to be 28.7 ±15.5 s, and choice of compositional map (for 20° and 5° maps) to be 10.3 ±12.2 s.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Transit Rider/Travel Behavior Inventory Survey - Minneapolis-St. Paul Metro - 1990

The 1990 transit on-board survey aimed to update the 1988 survey, which was conducted as part of the Preliminary Engineering Study for the Hennepin County Light Rail Transit System. The 1988 study received Regional Transit Board funding, and survey results could be applied to a mode split model for projecting ridership on the proposed Light Rail Transit System. However, this survey was designed with the 1990 Travel Behavior Inventory in mind. The intention had been to update the 1988 survey in 1990 to be compatible with the 1990 Travel Behavior Inventory data. The results of the 1990 survey were used primarily to create a table of observed transit trips between each of the 1,200 traffic analysis zones in the region. This trip table was used to calibrate a new mode split model, which estimated future year travel by mode. The 1990 update survey focused on new routes and routes that had changed significantly since 1988. To preserve compatibility with the 1988 survey, the same survey questionnaire card was used, together with the same survey procedures for data collection. The procedures randomly sampled bus patrons during the transit trip, asking key questions about the patron and the transit trip. The survey card was intended for patrons to fill out quickly so it could be completed during the transit trip. The questions focused on conditions that have proven over time to significantly influence ridership. In all, a total of 20,126 valid survey records were processed. Adding surrogate trips, the survey data file is composed of a total of 27,159 trip records . About 10% of the records were filled out by persons who had answered more than one questionnaire.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗