Search NASA⌕ Search

SEARCH · Search NASA

Results for “organic particles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Observationally constrained analysis on the distribution of fine- and coarse-mode nitrate in global models

Nitrate plays an important role in the Earth system and air quality. A key challenge in simulating the life cycle of nitrate aerosol in global models is to accurately represent mass size distribution of nitrate aerosol. In this study, we evaluate the performance of the Energy Exascale Earth System Model version 2 (E3SMv2) and the Community Earth System Model version 2 (CESM2), along with Aerosol Comparisons between Observations and Models (AeroCom) phase III models, in simulating spatial distribution of fine-mode nitrate, the mass size distribution of fine- and coarse-mode nitrate, and the gas–aerosol partitioning between nitric acid gas and nitrate, using long-term ground-based observations and measurements from multiple aircraft campaigns. We find that most models underestimate the annual mean PM 2.5 (particulate matter with diameter less than 2.5 µm) nitrate surface concentration averaged over all sites. The observed nitrate PM 2.5 / PM 10 and PM 1 / PM 4 ratios are influenced by the relative contribution of fine sulfate or organic particles and coarse dust or sea salt particles. Overall, the ground-based observations give an annual mean surface nitrate PM 2.5 / PM 10 ratio of 0.7. Most models underestimate the annual mean PM 2.5 / PM 10 ratio in all regions. There are large spreads in the modeled nitrate PM 1 / PM 4 ratios, which span the full range from 0 to 1. Most models underestimate the surface molar ratio of nitrate to total inorganic nitrate averaged across all sites. Our study indicates the importance of gas–aerosol partition parameterization and the simulation of dust and sea salt in correctly simulating the mass size distribution of nitrate.

Nitrate↗
DOE OSTI2024

Capturing the Relative‐Humidity‐Sensitive Gas–Particle Partitioning of Organic Aerosols in a 2D Volatility Basis Set

Abstract Aerosol water affects the physicochemical properties and mass concentration of organic aerosols (OA), but it is typically omitted by air quality, weather, and climate models. We compare two classes of simplified models to estimate the OA water uptake and gas–particle partitioning of organic compounds. One class uses a single‐hygroscopicity‐parameter (κ) approach while the other is based on the reduced‐complexity Binary Activity Thermodynamics (BAT) model. We show that a BAT‐based two‐dimensional volatility basis set (VBS) model always predicts a higher OA mass concentration at elevated relative humidity (RH), for example, ∼16% at 80% RH, than any variation of theκ‐based method considered—even when BAT‐VBS predicts a lower water uptake. The main reason being that the BAT‐VBS model captures variations in effective saturation mass concentration of organics (C*) with RH, a feature that other VBS methods lack. The BAT‐VBS framework offers an efficient, RH‐sensitive treatment for reduced‐complexity OA modeling.

Geology↗
DOE OSTI2020

Complex plant-derived organic aerosol as ice-nucleating particles – more than the sums of their parts?

Quantifying the impact of complex organic particles on the formation of ice crystals in clouds remains challenging, mostly due to the vast number of different sources ranging from sea spray to agricultural areas. In particular, there are many open questions regarding the ice nucleation properties of organic particles released from terrestrial sources such as decaying plant material. In this work, we present results from laboratory studies investigating the immersion freezing properties of individual organic compounds commonly found in plant tissue and complex organic aerosol particles from vegetated environments, without specifically investigating the contribution from biological particles, which may contribute to the overall ice nucleation efficiency observed at high temperatures. To characterize the ice nucleation properties of plant-related aerosol samples for temperatures between 242 and 267 K, we used the Aerosol Interaction and Dynamics in the Atmosphere (AIDA) cloud chamber and the Ice Nucleation SpEctrometer of the Karlsruhe Institute of Technology (INSEKT), which is a droplet freezing assay. Individual plant components (polysaccharides, lignin, soy and rice protein) were mostly less ice active, or similarly ice active, compared to microcrystalline cellulose, which has been suggested by recent studies to be a proxy for quantifying the primary cloud ice formation caused by particles originating from vegetation. In contrast, samples from ambient sources with a complex organic matter composition (agricultural soils and leaf litter) were either similarly ice active or up to 2 orders of magnitude more ice active than cellulose. Of all individual organic plant components, only carnauba wax (i.e., lipids) showed a similarly high ice nucleation activity as that of the samples from vegetated environments over a temperature range between 245 and 252 K. Hence, based on our experimental results, we suggest considering cellulose as being representative for the average ice nucleation activity of plant-derived particles, whereas lignin and plant proteins tend to provide a lower limit. In contrast, complex biogenic particles may exhibit ice nucleation activities which are up to 2 orders of magnitude higher than observed for cellulose, making ambient plant-derived particles a potentially important contributor to the population of ice-nucleating particles in the troposphere, even though major uncertainties regarding their transport to cloud altitude remain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The potential role of organics in new particle formation and initial growth in the remote tropical upper troposphere

Abstract. Global observations and model studies indicate that new particle formation (NPF) in the upper troposphere (UT) and subsequent particles supply 40 %–60 % of cloud condensation nuclei (CCN) in the lower troposphere, thus affecting the Earth's radiative budget. There are several plausible nucleation mechanisms and precursor species in this atmospheric region, which, in the absence of observational constraints, lead to uncertainties in modeled aerosols. In particular, the type of nucleation mechanism and concentrations of nucleation precursors, in part, determine the spatial distribution of new particles and resulting spatial distribution of CCN from this source. Although substantial advances in understanding NPF have been made in recent years, NPF processes in the UT in pristine marine regions are still poorly understood and are inadequately represented in global models. Here, we evaluate commonly used and state-of-the-art NPF schemes in a Lagrangian box model to assess which schemes and precursor concentrations best reproduce detailed in situ observations. Using measurements of aerosol size distributions (0.003 < Dp < 4.8 µm) in the remote marine troposphere between ∼0.18 and 13 km altitude obtained during the NASA Atmospheric Tomography (ATom) mission, we show that high concentrations of newly formed particles in the tropical UT over both the Atlantic and Pacific oceans are associated with outflow regions of deep convective clouds. We focus analysis on observations over the remote Pacific Ocean, which is a region less perturbed by continental emissions than the Atlantic. Comparing aerosol size distribution measurements over the remote Pacific with box model simulations for 32 cases shows that none of the NPF schemes most commonly used in global models, including binary nucleation of sulfuric acid and water (neutral and ion-assisted) and ternary involving sulfuric acid, water, and ammonia, are consistent with observations, regardless of precursor concentrations. Through sensitivity studies, we find that the nucleation scheme among those tested that is able to explain most consistently (21 of 32 cases) the observed size distributions is that of Riccobono et al. (2014), which involves both organic species and sulfuric acid. The method of Dunne et al. (2016), involving charged sulfuric acid–water–ammonia nucleation, when coupled with organic growth of the nucleated particles, was most consistent with the observations for 5 of 32 cases. Similarly, the neutral sulfuric acid–water–ammonia method of Napari (2002), when scaled with a tuning factor and with organic growth added, was most consistent for 6 of 32 cases. We find that to best reproduce both nucleation and growth rates, the mixing ratios of gas-phase organic precursors generally need to be at least twice that of SO2, a proxy for dimethyl sulfide (DMS). Unfortunately, we have no information on the nature of oxidized organic species that participated in NPF in this region. Global models rarely include organic-driven nucleation and growth pathways in UT conditions where globally significant NPF takes place, which may result in poor estimates of NPF and CCN abundance and contribute to uncertainties in aerosol–cloud–radiation effects. Furthermore, our results indicate that the organic aerosol precursor vapors may be important in the tropical UT above marine regions, a finding that should guide future observational efforts.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Impact of Urban Pollution on Organic-Mediated New-Particle Formation and Particle Number Concentration in the Amazon Rainforest

A major challenge in assessing the impact of aerosols on climate change is to understand how human activities change aerosol loading and properties relative to the pristine-preindustrial baseline. Here we combine chemical transport simulation and field measurements to investigate the effect of anthropogenic pollution from an isolated metropolis on particle number concentration over the preindustrial-like Amazon rainforest through various new-particle formation (NPF) mechanisms and primary particle emissions. To represent organic-mediated NPF, we employ a state-of-the-art model that systematically simulates the formation chemistry and thermodynamics of extremely low volatility organic compounds as well as their roles in NPF processes, and further update the model to improve organic NPF simulations under human-influenced conditions. Results show that urban pollution from the metropolis increases particle number concentration by a factor of 5–25 over the downwind region (within 200 km from city center) compared to background conditions. Overall, our model indicates that NPF contributes over 70% of the total particle number in the downwind region except immediately adjacent to the sources. Among different NPF mechanisms, the ternary NPF involving organics and sulfuric acid overwhelmingly dominates. The improved understanding of particle formation mechanisms will help better quantify anthropogenic aerosol forcing from pristine-preindustrial times to present day.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Measurement report: Role of organic coating and chemical composition on ice nucleation potential of atmospheric particles in European Arctic

Understanding the ice nucleation (IN) potential of Arctic aerosols is critical for predicting their influence on cloud formation and water cycles in this vulnerable region. This study investigates the role of particle composition, organic coatings, and aerosol sources in modulating ice nucleating particle (INPs) abundance across five aerosol samples collected at the Gruvebadet Observatory Station in Ny-Ålesund, Svalbard. The IN potential of Arctic aerosol particles was studied by investigating chemical, morphological, and INP abundance measurements. Single-particle analyses revealed distinct differences in mixing state, organic volume fraction (OVF), and organic coating morphology across samples. OVF distributions were linked to particle origin, with marine-influenced Na-rich particles often exhibiting thin organic coatings, while long-range transported particles showed thicker organic coatings. Biogenic contributions, though variable, were linked to heat-sensitive INPs, suggesting a role for labile biological macromolecules under certain meteorological conditions. Spearman rank correlation analysis between particle composition and immersion-mode INP concentrations at two freezing temperatures indicated that organic-rich and Na-rich particles were positively associated with enhanced INP abundance. However, discrepancies in INP abundance were observed for particles with thicker organic coatings, where the morphological configuration of the organic material may play a role. The results highlight that Arctic INP variability is governed not only by chemical composition but also by the morphological configuration of organic material, which can either enhance or inhibit ice nucleation depending on its abundance, distribution, thickness, and mixing state. These findings underscore the combined influence of source regions, atmospheric processing, and organic–inorganic interactions in shaping Arctic aerosol freezing behavior.

Lata, Nurun Nahar [Pacific Northwest National Labo↗
DOE OSTI2022

Solid organic-coated ammonium sulfate particles at high relative humidity in the summertime Arctic atmosphere

The ability of atmospheric aerosols to impact climate through water uptake and cloud formation is fundamentally determined by the size, composition, and phase (liquid, semisolid, or solid) of individual particles. Particle phase is dependent on atmospheric conditions (relative humidity and temperature) and chemical composition and, importantly, solid particles can inhibit the uptake of water and other trace gases, even under humid conditions. Particles composed primarily of ammonium sulfate are presumed to be liquid at the relative humidities (67 to 98%) and temperatures (–2 to 4 °C) of the summertime Arctic. Under these atmospheric conditions, we report the observation of solid organic-coated ammonium sulfate particles representing 30% of particles, by number, in a key size range (<0.2 µm) for cloud activation within marine air masses from the Arctic Ocean at Utqiagvik, AK. The composition and size of the observed particles are consistent with recent Arctic modeling and observational results showing new particle formation and growth from dimethylsulfide oxidation to form sulfuric acid, reaction with ammonia, and condensation of marine biogenic sulfate and highly oxygenated organic molecules. Aqueous sulfate particles typically undergo efflorescence and solidify at relative humidities of less than 34%. Therefore, the observed solid phase is hypothesized to occur from contact efflorescence during collision of a newly formed Aitken mode sulfate particle with an organic-coated ammonium sulfate particle. With declining sea ice in the warming Arctic, this particle source is expected to increase with increasing open water and marine biogenic emissions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Elucidating the Influence of Metal Surface Composition on Organic Adsorbate Binding Using Active Particle Dynamics

The adsorption strengths of organic compounds on metal surfaces are sensitive to the metal composition, and they play a central role in many catalytic reactions, helping to control the coverage of the reactant and altering the overall reaction rate. While adsorption energies are straightforward to measure and calculate in vacuum and gas-phase environments, adsorption energetics can be dramatically altered by the presence of solvent in liquid-phase reactions. However, the effects of metal composition on binding strengths in a liquid environment are less well understood, primarily due to the difficulty of accurate in situ measurements of organic binding on metal surfaces in the liquid phase. Here, we utilize the motion of active particles in water to probe the adsorption energies of an organic adsorbate (furfural) on a range of metal surfaces (pure Pd, pure Pt, and four PdAu alloy compositions) to elucidate the effect of metal composition. Janus particles with catalytic caps of particular metal compositions all exhibited active motion resulting from consumption of H 2 O 2 ; adsorbate binding was inferred through the decrease in the velocity of active motion and was modeled by a Langmuir adsorption isotherm. The measured adsorption affinities were used to extract the adsorption enthalpy of furfural on the different metals. The Pd surface was found to bind furfural more strongly than the Pt surface by some 10 kJ/mol. Furthermore, the adsorption of furfural on the alloys was found to increase monotonically in magnitude with Pd content. As a result, the data reported herein aid the development of accurate understanding of organic adsorption in the presence of solvent and the role of the metal surface in tuning adsorption strengths to optimize catalytic processes in the liquid phase.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Monolayer organic thin films as particle-contamination–resistant coatings

Abstract Three organic monolayers coatings were developed and tested for their effectiveness to increase cleaning efficiency of attached microscale particles by air flows. The experiments were performed using silica substrates coated with these organic thin films and subsequently exposed to stainless-steel and silica microparticles as a model of contamination. Laser-induced–damage tests confirmed that the coatings do not affect the laser-induced–damage threshold values. The particle exposure results suggest that although the accumulation of particles is not significantly affected under the experimental conditions used in this work, the coated substrates exhibit significantly improved cleaning efficiency with a gas flow. A size-distribution analysis was conducted to study the adsorption and cleaning efficiency of particles of different sizes. It was observed that larger size (> 5-μm) particles can be removed from coated substrates with almost 100% efficiency. It was also determined that the coatings improve the cleaning efficiency of the smaller particles (≤ 5 μm) by 17% to 30% for the stainless steel metal and 19% to 38% for the silica particles.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Non-Reciprocity, Metastability, and Dynamic Reconfiguration in Co-Assembly of Active and Passive Particles

Living organisms often exhibit non-reciprocal interactions where the forces acting on the objects are not equal in magnitude or opposite in direction. The combination of reciprocal and non-reciprocal interactions between synthetic building blocks remains largely unexplored. Here, out-of-equilibrium assemblies of non-motile isotropic passive and metal-patched motile active particles are formed by overlapping bulk interactions with directed self-propulsion. An external alternating current (AC) electric field generates concurrent dipolar and induced-charge electrophoretic forces between the particles which are evaluated using microscopy. The interaction force measurements allow to determine the degree of reciprocity in interactions, which is tunable by designing the active particle and its trajectory. While linearly-propelled active particles evade assembly with passive particles, helically propelled active particles form active-passive clusters with dynamic reconfiguration and long-lived metastability. Large clusters display programmable fluctuations and reconfigurability by controlling the fraction of active particles. The study establishes principles of integrating reciprocal and non-reciprocal interactions in guided colloidal assembly of reconfigurable metastable structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Phase Transitions in Organic and Organic/Inorganic Aerosol Particles

The phase state of aerosol particles can impact numerous atmospheric processes, including new particle growth, heterogeneous chemistry, cloud condensation nucleus formation, and ice nucleation. In this article, the phase transitions of inorganic, organic, and organic/inorganic aerosol particles are discussed, with particular focus on liquid-liquid phase separation (LLPS). The physical chemistry that determines whether LLPS occurs, at what relative humidity it occurs, and the resultant particle morphology is explained using both theoretical and experimental methods. The known impacts of LLPS on aerosol processes in the atmosphere are discussed. Finally, potential evidence for LLPS from field and chamber studies is presented. By understanding the physical chemistry of the phase transitions of aerosol particles, we will acquire a better understanding of aerosol processes, which in turn impact human health and climate.

Chemistry↗
DOE OSTI2023

Correlating the Viscosity and Rate of Water Diffusion in Semisolid Gel-Forming Aerosol Particles

Aerosol particles are known to exist in highly viscous amorphous states at a low relative humidity and temperature. The slow diffusion of molecules in viscous particles impacts the uptake and loss of volatile and semivolatile species and the rate of heterogeneous chemistry. Recent work has demonstrated that in particles containing organic molecules and salts, the formation of two-phase gel states is possible, leading to observations of rigid particles that resist coalescence. The way that molecules diffuse and transport in gel systems is not well-characterized. In this work, we use an electrodynamic balance to levitate sample particles containing a range of organic compounds in mixtures with calcium chloride and measure the rate of water diffusion. Particles of the pure organics have been shown to form viscous amorphous states, while in mixtures with divalent salts, coalescence measurements have revealed the apparent solidification of particles, consistent with the formation of a gel state facilitated by ion–molecule interactions. We report in several cases that water transport can actually be increased in the rigid gel state relative to the pure compound that forms a viscous state under similar conditions. These measurements reveal the limitations of using viscosity as a metric for predicting molecular diffusion and that the gel structure that forms is a much stronger controlling factor in the rate of diffusion. In conclusion, this underscores the need for diffusion measurements as well as a deeper understanding of noncovalent molecular assembly that leads to supramolecular structures in aerosol particles.

organic-inorganic mixtures↗
DOE OSTI2021

Engineering the Si Anode Interface via Particle Surface Modification: Embedded Organic Carbonates Lead to Enhanced Performance

Si nanoparticles (SiNPs) are recognized as a promising anode material for next-generation high-energy lithium-ion batteries. However, due to the more stringent requirements resulting from severe volume change, the solid-electrolyte interphase (SEI) on SiNPs plays a critical role in determining their cycling performance. Engineering the interface for higher stability has become an effective yet challenging approach to accommodate the deterioration of the silicon anode from the repeated lithiation/delithiation process. Herein, we report a novel approach of engineering a covalently bonded organic monolayer of ethylene carbonates onto the surface of the SiNPs that can help form a sturdy SEI. Finally, this molecule-level surface modification provides an effective approach to enable high-energy lithium-ion batteries with Si anodes.

25 ENERGY STORAGE↗