Search NASA⌕ Search

SEARCH · Search NASA

Results for “oxide coatings”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Thermal Properties of Oxides With Magnetoplumbite Structure for Advanced Thermal Barrier Coatings

Oxides having magnetoplumbite structure are promising candidate materials for applications as high temperature thermal barrier coatings because of their high thermal stability, high thermal expansion, and low thermal conductivity. In this study, powders of LaMgAl11O19, GdMgAl11O19, SmMgAl11O19, and Gd0.7Yb0.3MgAl11O19 magnetoplumbite oxides were synthesized by citric acid sol-gel method and hot pressed into disk specimens. The thermal expansion coefficients (CTE) of these oxide materials were measured from room temperature to 1500 C. The average CTE value was found to be approx.9.6x10(exp -6)/C. Thermal conductivity of these magnetoplumbite-based oxide materials was also evaluated using steady-state laser heat flux test method. The effects of doping on thermal properties were also examined. Thermal conductivity of the doped Gd0.7Yb0.3MgAl11O19 composition was found to be lower than that of the undoped GdMgAl11O19. In contrast, thermal expansion coefficient was found to be independent of the oxide composition and appears to be controlled by the magnetoplumbite crystal structure. Thermal conductivity testing of LaMgAl11O19 and LaMnAl11O19 magnetoplumbite oxide coatings plasma sprayed on NiCrAlY/Rene N5 superalloy substrates indicated resistance of these coatings to sintering even at temperatures as high as 1600 C.

Bansal, Narottam P.↗
NASA NTRS1985

Thermal barrier coating life prediction model

This is the first report of the first phase of a 3-year program. Its objectives are to determine the predominant modes of degradation of a plasma sprayed thermal barrier coating system, then to develop and verify life prediction models accounting for these degradation modes. The first task (Task I) is to determine the major failure mechanisms. Presently, bond coat oxidation and bond coat creep are being evaluated as potential TBC failure mechanisms. The baseline TBC system consists of an air plasma sprayed ZrO2-Y2O3 top coat, a low pressure plasma sprayed NiCrAlY bond coat, and a Rene'80 substrate. Pre-exposures in air and argon combined with thermal cycle tests in air and argon are being utilized to evaluate bond coat oxidation as a failure mechanism. Unexpectedly, the specimens pre-exposed in argon failed before the specimens pre-exposed in air in subsequent thermal cycles testing in air. Four bond coats with different creep strengths are being utilized to evaluate the effect of bond coat creep on TBC degradation. These bond coats received an aluminide overcoat prior to application of the top coat to reduce the differences in bond coat oxidation behavior. Thermal cycle testing has been initiated. Methods have been selected for measuring tensile strength, Poisson's ratio, dynamic modulus and coefficient of thermal expansion both of the bond coat and top coat layers.

Hillery, R. V.↗
NASA NTRS1980

Preliminary study of a solar selective coating system using black cobalt oxide for high temperature solar collectors

Black cobalt oxide coatings were deposited on thin layers of silver or gold which had been deposited on oxidized stainless steel substrates. The reflectance properties of these coatings were measured at various thicknesses of cobalt oxide for integrated values of the solar and infrared spectrum. The values of absorptance and emittance were calculated from the measured reflectance values before and after exposure in air at 650 C for 1000 hours. Also, these cobalt oxide/noble metal/oxide diffusion barrier coatings have absorptances greater than 0.90 and emittances of approximately 0.20 even after about 1000 hours at 650 C.

Mcdonald, G.↗
NASA NTRSDate not supplied

Measuring the Wear and Abrasive Resistance of Air Plasma Sprayed Aluminum Oxide for Lunar Exploration

Lunar regolith, especially finer dust particles traveling at high velocities, can cause significant wear and abrasive damage to structural components that ensure a prolongated presence on the surface of the Moon. With the absence of an atmosphere and lower gravity than on Earth, regolith particles maintain high velocities at large distances from where they were generated, for example next to lunar landers. Wear-resistant ceramic and ceramic composite materials can improve the durability of spacecraft components during long missions on the Moon’s surface. Aluminum oxide coatings are lightweight, have multifunctional properties, and have high strength including high hardness and wear resistance. These properties can help improve the durability of structures used in space exploration. Air plasma sprayed (APS) aluminum oxide coatings have demonstrated the potential to protect critical structures. This study investigated the abrasive wear resistance of APS aluminum oxide coatings via Taber abrasion experiments. Taber abrasion offers the advantage of quantifying the abrasive wear behavior of particles with different shapes on a surface. In this work, an abrasive wheel made of silicon carbide was utilized to evaluate wear properties of specimens progressively over 5000 cycles. This experiment focused on testing two series of specimens to determine whether a bond coat composed of nickel, chromium, aluminum, and yttrium (NiCrAlY) improved the protective behavior of the APS aluminum oxide coating. The specimens varied in topcoat thickness and were made with and without an approximately 100 µm bond coat layer. The mass of the specimens was measured at 400 cycles, 800 cycles, 3800 cycles, and 5000 cycles. Increasing thickness was found to result in higher wear for samples with and without a bond coat. Increased mass loss in samples with a bond coat was observed indicating a need for further studies on the overall impact of the use of a bond coat on the protective behavior of the coatings. To continue designing wear resistant coatings for structural protection in space missions, the multifunctional properties of the APS aluminum oxide coating will be studied. Future experiments will determine whether the APS aluminum oxide coating can protect the structures from other aspects of the harsh space environment, such as extreme temperature variations and ionizing radiation.

aluminum oxide↗
NASA NTRS1980

Preliminary study of a solar selective coating system using black cobalt oxide for high temperature solar collectors

Black cobalt oxide coatings (high solar absorptance layer) were deposited on thin layers of silver or gold (low emittance layer) which had been previously deposited on oxidized (diffusion barrier layer) stainless steel substrates. The reflectance properties of these coatings were measured at various thicknesses of cobalt for integrated values of the solar and infrared spectrum. The values of absorptance and emittance were calculated from the measured reflectance values, before and after exposure in air at 650 C for approximately 1000 hours. Absorptance and emittance were interdependent functions of the weight of cobalt oxide. Also, these cobalt oxide/noble metal/oxide diffusion barrier coatings have absorptances greater than 0.90 and emittances of approximately 0.20 even after about 1000 hours at 650 C.

Mcdonald, G.↗
NASA NTRS1961

Investigation of Oxidation-Resistant Coatings on Graphite and Molybdenum in Two Arc-Powered Facilities

A number of leading-edge specimens of ATJ graphite and 0.5-percent titanium-molybdenum alloy were tested in a 6-inch subsonic low-pressure arc-powered tunnel and a 1,500-kw subsonic arc jet to determine the effectiveness of several refractory coatings in preventing the oxidation of these materials. The results indicate that the siliconized coating for the ATJ graphite and the W-2 and Durak MG coatings for the titanium-molybdenum alloy provide adequate protection at temperatures up to 3,000 F for the durations of the tests in these facilities, approximately 70 seconds in the arc tunnel and approximately 10 minutes in the arc jet. Weight losses (less than one-half of 1 percent) experienced by a few of the coated specimens indicate that tests of longer duration in these environments may prove deleterious and that the stability of these coatings may be depreciated under the low-pressure environmental conditions encountered during reentry.

Peters, Roger W.↗
NASA NTRS1981

A new diffusion-inhibited oxidation-resistant coating for superalloys

A concept for enhanced protection of superalloys consists of adding an oxidation- and diffusion-resistant cermet layer between the superalloy and the outer oxidation-resistant metallic alloy coating. Such a duplex coating was compared with a physical-vapor-deposited (PVD) NiCrAlY coating in cyclic oxidation at 1150 C. The substrate alloy was MA 754 - an oxide-dispersion-strengthened superalloy that is difficult to coat. The duplex coating, applied by plasma spraying, outperformed the PVD coating on the basis of weight change and both macroscopic and metallographic observations.

Gedwill, M. A.↗
NASA NTRS1985

Oxidation protection coatings for polymers

A polymeric substrate is coated with a metal oxide film to provide oxidation protection in low Earth orbital environments. The film contains about 4 volume percent polymer to provide flexibility. A coil of polymer material moves through an ion beam as it is fed between reels. The ion beam first cleans the polymer material surface and then sputters the film material from a target onto this surface.

Mirtich, M. J.↗
NASA NTRS1986

Apparatus for producing oxidation protection coatings for polymers

A polymeric substrate is coated with a metal oxide film to provide oxidation protection in low Earth orbital environments. The film contains about 4 volume percent polymer to provide flexibility. A coil of polymer materials moves through an ion beam as it is fed between reels. The ion beam first cleans the polymer material surface and then sputters the film material from a target onto this surface.

Mirtich, M. J.↗