Search NASA⌕ Search

SEARCH · Search NASA

Results for “pillar compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

49 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Dislocation-graphene interactions in Cu/graphene composites and the effect of boundary conditions: a molecular dynamics study

Here, in this paper, systematic molecular dynamics simulations were employed to study dislocation-graphene interactions in Cu/graphene systems using two carefully selected configurations: (i) edge dislocations in the pileup interacting with graphene during nanoindentation and (ii) complex dislocations interacting with graphene in compression of layered nanopillars. The intrinsic and extrinsic size effects were investigated with respect to varying the Cu lamella thickness and pillar sizes, revealing an anomalous extrinsic size effect: the smaller, the weaker. To understand which boundary conditions are physically consistent, both free and periodic graphene were considered. It was seen that edge dislocations in the pileup continuously transmitted across the free graphene through Cu/graphene interfacial sliding and graphene reorientation, whereas transmission was very difficult for periodic graphene as its in-plane deformation was required. In compression of Cu/graphene nanopillars, the strengthening effect of free graphene was found to be less obvious than that of the periodic case, which could be attributed to free graphene edges acting as dislocation sources after the compressed Cu overflowed the graphene sheet from all directions. We therefore conclude that the strengthening effect of periodic graphene inclusions appears to be overestimated, such that free graphene should be more appropriate.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Amorphization and Plasticity of Olivine During Low-Temperature Micropillar Deformation Experiments

Experimentally quantifying the viscoplastic rheology of olivine at the high stresses and low temperatures of the shallow lithosphere is challenging due to olivine's propensity to deform by brittle mechanisms at these conditions. In this study, we use microscale uniaxial compression tests to investigate the rheology of an olivine single crystal at room pressure and temperature. Pillars with nominal diameters of 1.25 μm were prepared using a focused ion beam milling technique and were subjected to sustained axial stresses of several gigapascal. The majority of the pillars failed after dwell times ranging from several seconds to a few hours. However, several pillars exhibited clear evidence of plastic deformation without failure after 4–8 hr under load. The corresponding creep strain rates are estimated to be on the order of 10-6 to 10 -7 s -1 . The uniaxial stresses required to achieve this deformation (4.1–4.4 GPa) are in excellent agreement with complementary data obtained using nanoindentation techniques. Scanning transmission electron microscopy observations indicate that deformation occurred along amorphous shear bands within the deformed pillars. Electron energy loss spectroscopy measurements revealed that the bands are enriched in Fe and depleted in Mg. We propose that inhomogeneities in the cation distribution in olivine concentrate stress and promote the amorphization of the Fe-rich regions. Finally, the time dependence of catastrophic failure events suggests that the amorphous bands must grow to some critical length scale to generate an unstable defect, such as a shear crack.

58 GEOSCIENCES↗
DOE OSTI2023

Method for micromolding a polymeric membrane having a pore array

A method for micro-molding a polymeric membrane and including pouring a predetermined volume of curable polymer unto a micro-fabricated mold having a post array with pillars, and overlaying the polymer with a support substrate. A spacer, such as a rubber spacer, is placed in contact with the support substrate and a force is applied to an exposed side of the spacer to compress the support substrate and the polymer together. While applying the force, the polymer is cured on the mold for a predetermined time period and at a predetermined temperature to form a polymeric membrane having a pore array with a plurality of pores corresponding to the plurality of pillars of the post array. The polymeric membrane is removed from the support substrate.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mechanical properties and deformation mechanisms of single crystal Mg micropillars subjected to high-strain-rate C-axis compression

Here, the mechanical properties and deformation mechanisms of single crystal magnesium under c-axis quasi-static and high-strain rate compressions are investigated through in situ scanning electron microscope (SEM) experiments and post-mortem transmission electron microscope (TEM) characterization. The findings revealed that ductility and high rates of hardening are preserved for pillars as large as 15 μm. Furthermore, rate effects result in a mild increase in flow stress with plastic deformations controlled primarily by the slip of type dislocations. Importantly and in contrast to other literature reports, plastic deformation occurs in the absence of twining. As the strain increases and plastic deformation exceeds about 4%, crystal rotation activates basal slip, <$\mathrm{a}$> type dislocations, resulting in a more rate independent flow stress. TEM observation on micropillars compressed at a strain rate of 250/s, revealed the activation of {${11}$$\bar{2}$$\bar{2}$} < $\bar{1}$$\bar{1}23$ > slip systems and high mobility of screw dislocations as major contributors to plastic strains in excess of 10% without fracture. These findings are relevant to the design of lightweight materials used in transportation systems, e.g., selection of material grain size. Moreover, the experimental data here reported provides the materials science community with a unique opportunity to validate discrete dislocation dynamics (DDD) formulations employed in multiscale design of materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evidence for a High Temperature Whisker Growth Mechanism Active in Tungsten during In Situ Nanopillar Compression

A series of nanopillar compression tests were performed on tungsten as a function of temperature using in situ transmission electron microscopy with localized laser heating. Surface oxidation was observed to form on the pillars and grow in thickness with increasing temperature. Deformation between 850 °C and 1120 °C is facilitated by long-range diffusional transport from the tungsten pillar onto adjacent regions of the Y2O3-stabilized ZrO2 indenter. The constraint imposed by the surface oxidation is hypothesized to underly this mechanism for localized plasticity, which is generally the so-called whisker growth mechanism. The results are discussed in context of the tungsten fuzz growth mechanism in He plasma-facing environments. The two processes exhibit similar morphological features and the conditions under which fuzz evolves appear to satisfy the conditions necessary to induce whisker growth.

36 MATERIALS SCIENCE↗
NASA NTRS2012

Fabrication of a Silicon Backshort Assembly for Waveguide-Coupled Superconducting Detectors

The Cosmology Large Angular Scale Surveyor (CLASS) is a ground-based instrument that will measure the polarization of the cosmic microwave background to search for evidence for gravitational waves from a posited epoch of inflation early in the Universe s history. This measurement will require integration of superconducting transition-edge sensors with microwave waveguide inputs with excellent control of systematic errors, such as unwanted coupling to stray signals at frequencies outside of a precisely defined microwave band. To address these needs we present work on the fabrication of micromachined silicon, producing conductive quarter-wave backshort assemblies for the CLASS 40 GHz focal plane. Each 40 GHz backshort assembly consists of three degeneratively doped silicon wafers. Two spacer wafers are micromachined with through-wafer vias to provide a 2.04 mm long square waveguide delay section. The third wafer terminates the waveguide delay in a short. The three wafers are bonded at the wafer level by Au-Au thermal compression bonding then aligned and flip chip bonded to the CLASS detector at the chip level. The micromachining techniques used have been optimized to create high aspect ratio waveguides, silicon pillars, and relief trenches with the goal of providing improved out of band signal rejection. We will discuss the fabrication of integrated CLASS superconducting detector chips with the quarter-wave backshort assemblies.

Crowe, Erik J.↗
NASA NTRS2012

Fabrication of Silicon Backshorts with Improved Out-of-Band Rejection for Waveguide-Coupled Superconducting Detectors

The Cosmology Large Angular Scale Surveyor (CLASS) is a ground-based instrument that will measure the polarization of the cosmic microqave background to search for gravitational waves form a posited epoch of inflation early in the universe's history. This measurement will require integration of superconducting transition-edge sensors with microwave waveguide inputs with good conrol of systematic errors, such as unwanted coupling to stray signals at frequencies outside of a precisely defined microwave band. To address these needs we will present work on the fabrication of silicon quarter-wave backshorts for the CLASS 40GHz focal plane. The 40GHz backshort consists of three degeneratively doped silicon wafers. Two spacer wafers are micromachined with through wafer vins to provide a 2.0mm long square waveguide. The third wafer acts as the backshort cap. The three wafers are bonded at the wafer level by Au-Au thermal compression bonding then aligned and flip chip bonded to the CLASS detector at the chip level. The micromachining techniques used have been optimized to create high aspect ratio waveguides, silicon pillars, and relief trenches with the goal of providing improved out of band signal rejection. We will discuss the fabrication of integrated CLASS superconducting detectors with silicon quarter wave backshorts and present current measurement results.

Crowe, Erik J.↗
NASA NTRS2013

Towards Probablistic Assessment of Hypobaric Decompression Sickness Treatment

INTRODUCTION: Pressure, oxygen (O2), and time are the pillars to effective treatment of decompression sickness (DCS). The NASA DCS Treatment Model links a decrease in computed bubble volume to the resolution of a symptom. The decrease in volume is realized in two stages: a) during the Boyle's Law compression and b) during subsequent dissolution of the gas phase by the O2 window. METHODS: The cumulative distribution of 154 symptoms that resolved during repressurization was described with a log-logistic density function of pressure difference (deltaP as psid) associated with symptom resolution and two other explanatory variables. The 154 symptoms originated from 119 cases of DCS during 969 exposures in 47 different altitude tests. RESULTS: The probability of symptom resolution [P(symptom resolution)] = 1 / (1+exp(- (ln(deltaP) - 1.682 + 1.089×AMB - 0.00395×SYMPTOM TIME) / 0.633)), where AMB is 1 when the subject ambulated as part of the altitude exposure or else 0 and SYMPTOM TIME is the elapsed time in min from start of the altitude exposure to recognition of a DCS symptom. The P(symptom resolution) was estimated from computed deltaP from the Tissue Bubble Dynamics Model based on the "effective" Boyle's Law change: P2 - P1 (deltaP, psid) = P1×V1/V2 - P1, where V1 is the computed volume of a spherical bubble in a unit volume of tissue at low pressure P1 and V2 is computed volume after a change to a higher pressure P2. V2 continues to decrease through time at P2, at a faster rate if 100% ground level O2 was breathed. The computed deltaP is the effective treatment pressure at any point in time as if the entire deltaP was just from Boyle's Law compression. DISCUSSION: Given the low probability of DCS during extravehicular activity and the prompt treatment of a symptom with options through the model it is likely that the symptom and gas phase will resolve with minimum resources and minimal impact on astronaut health, safety, and productivity.

Conkin, J.↗
DOE OSTI2020

Understanding Charge Storage in Hydrated Layered Solids MOPO 4 (M = V, Nb) with Tunable Interlayer Chemistry

Hydrated layered solids are interesting charge storage hosts with potentially high electrochemical activity and interlayer tunability. Although it is often possible to tune their interlayer distance by a pillaring strategy, the poor electrochemical stability of such artificial structures remains a major issue in device operation. Here we investigate the charge storage properties of MOPO 4 (M = V, Nb) hydrates with a nanosheet morphology to understand the influence of the interlayer environment on cycling stability, as well as ion selectivity. While in hydrated VOPO 4 interlayer H 2 O molecules act as compressible springs to enable fast Li-/Na-ion transport kinetics and reasonable structural reversibility, NbOPO 4 layers with bridging PO 4 groups serving as permanent linkers exhibit highly stable cyclability for Li-ions, owing to a zero-volume-change ion transport process. However, the latter suffers from a much larger migration energy barrier for Na-ions. Lastly, our findings not only highlight a structurally intriguing material system, but also provide insights into reviving materials with an originally unstable interlayer chemical environment, and shed light on the design principles for creating electrochemically stable charge storage hosts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Femtosecond damage experiments and modeling of broadband mid-infrared dielectric diffraction gratings

High peak and average power lasers with high wall-plug efficiency, like the Big Aperture Thulium (BAT) laser, have garnered tremendous attention in laser technology. To meet the requirements of the BAT laser, we have developed low-dispersion reflection multilayer dielectric (MLD) gratings suitable for compression of high-energy pulses for operations at 2 micron wavelength. We carried out 10000-on-1 damage tests to investigate the fluence damage thresholds of the designed MLD gratings and mirrors, which were found between 100-230 mJ/cm 2 . An ultrashort pulsed laser (FWHM = 53 fs, λ = 1.9 μ m) operating at 500 Hz was used in the serpentine raster scans. The atomic force microscope images of the damage sites show blister formation of the underlying layers at lower fluences but ablation of the grating pillars at higher fluences. We simulated the dynamic electronic excitation in the MLD optics with a finite-difference in the time domain approach in 2D. The simulation results agree well with the LIDT measurements and the observed blister formation. This model is able to evaluate the absolute LIDT of MLD gratings.

42 ENGINEERING↗
NASA NTRS2019

Continuous Electrode Inertial Electrostatic Confinement Fusion

The NIAC Phase I project on Inertial Electrostatic Confinement was a continuation of early stage research that was funded by an NSTRF. The student on the project, Andrew Chap, was funded by the NSTRF from Fall 2013 through the Summer of 2017, and then was funded on the NIAC through the completion of his PhD. A significant amount of work targeting the plasma confinement physics was the focus of his NSTRF, and over the course of that effort he developed a number of analyses and computational tools that leveraged GPU parallelization. A detailed discussion of these models can be found in his dissertation, which has been included as Appendix D in this report. As a requirement for the NSTRF, Andrew's full dissertation was submitted at the end of the program.Having developed the computational tools, a substantial amount of simulation and analyses leveraging those tools were conducted during the Fall of 2017, under the auspices of the NIAC funded research. Much of this work targeted optimization of the confinement fields, investigating their structure and the possible advantages of having them be time-varying. The results of these simulations can also be found in Appendix D.One of the main results from this research is that the density of ions electrostatically confined within the system can indeed be increased by several orders of magnitude by optimizing the radial potential distribution, and by dynamically varying these fields to maintain compressed ion bunches. An electron population can also be confined within the core by a static radial cusped magnetic field,which helps to support a greater ion density within the core. The issue with the confinement mechanism is that as the ion densities are increased toward fusion-relevant levels, the electrostatic forces generated by the confined electron population become so great that the ions are no longer energetic enough to leave the device core. As their excursions into the outer channels are diminished, the mechanism that is used to maintain their non-thermal velocity distributions becomes ineffective, and eventually the ions become fully confined within the core, where they thermalize. A possible fix to the problem comes by discarding the active ion control (a main pillar of the concept)but retaining the structure of the permanent magnet confinement of the electron population. Such cusped field confinement has been the focus of other IEC approaches (e.g. Polywell), but the high transparency of the permanent magnet structure lends itself to better ion extraction and power conversion (a second pillar of the concept). The question then becomes whether any influence on the ion evolution within the core can be achieved to slow the thermalization of the ions. Such approaches have been studied in highly idealized analytic models, but face major criticisms within the literature. While this is a possible path forward, the uncertainty in the approach did not warrant committing NIAC Phase II resources to investigating the concept at this time.

Sedwick, Raymond↗
NASA NTRSDate not supplied

A New Era of H-O-C-S Magma Solubility Modeling: Better, Faster, Stronger

H 2 O, CO 2 , and S are the most abundant volatiles in magmatic systems and are critical to understanding magma storage, phase equilibria, and volcanic eruptions. Models that consider all three of these components, however, may not allow for critical examination and adjustment of assumptions underlying the model, or provide benchmark testing or extensible interfaces. Thus, understanding why models produce different results can be challenging. We have gathered authors of established (D-Compress) and recent (VolFe, EVo, Sulfur_X, MAGEC) H-O-C-S volatile solubility models to work together to understand how and why our models diverge. We present a series of benchmark basalt degassing scenarios revealing that often understated model assumptions such as fO 2 buffer equations, fO 2 -Fe 3+ /ΣFe relationships, and even major element normalization routines have outsized effects on model results. All models consider S 2- and S 6+ melt species but with different approaches to sulfate/sulfide capacities, partition coefficients, and species fugacities, leading to divergence in the evolution of modeled gas compositions, melt S and Fe speciation, and fO 2 , with the extent of divergence depending on melt composition. Such scenarios enable meaningful intercomparison of existing models and lay the groundwork for a user-friendly yet powerful solubility modeling framework. Given our wealth of existing solubility literature, we suggest that the field of magmatic volatiles should focus now on the creation of modern tools and the modular implementation of existing model equations or methods, and that the evaluation of code usability, transparency, and benchmarking should be codified pillars of the peer-review process. As an example of such an endeavor, we present early work coupling these sulfur solubility models with VESIcal, an extensible and rigorously tested python library containing seven existing H 2 O-CO 2 solubility models. VESIcal includes the ability to extract, edit, and even interchange assumptions underlying any model. For example, users may combine or swap separately published H 2 O, CO 2 , and S models, as well as underlying model choices, such as Equations of State and redox models.

volatiles in magmas↗
NASA NTRS2004

Bubble Combustion

A method of energy production that is capable of low pollutant emissions is fundamental to one of the four pillars of NASA s Aeronautics Blueprint: Revolutionary Vehicles. Bubble combustion, a new engine technology currently being developed at Glenn Research Center promises to provide low emissions combustion in support of NASA s vision under the Emissions Element because it generates power, while minimizing the production of carbon dioxide (CO2) and nitrous oxides (NOx), both known to be Greenhouse gases. and allows the use of alternative fuels such as corn oil, low-grade fuels, and even used motor oil. Bubble combustion is analogous to the inverse of spray combustion: the difference between bubble and spray combustion is that spray combustion is spraying a liquid in to a gas to form droplets, whereas bubble combustion involves injecting a gas into a liquid to form gaseous bubbles. In bubble combustion, the process for the ignition of the bubbles takes place on a time scale of less than a nanosecond and begins with acoustic waves perturbing each bubble. This perturbation causes the local pressure to drop below the vapor pressure of the liquid thus producing cavitation in which the bubble diameter grows, and upon reversal of the oscillating pressure field, the bubble then collapses rapidly with the aid of the high surface tension forces acting on the wall of the bubble. The rapid and violent collapse causes the temperatures inside the bubbles to soar as a result of adiabatic heating. As the temperatures rise, the gaseous contents of the bubble ignite with the bubble itself serving as its own combustion chamber. After ignition, this is the time in the bubble s life cycle where power is generated, and CO2, and NOx among other species, are produced. However, the pollutants CO2 and NOx are absorbed into the surrounding liquid. The importance of bubble combustion is that it generates power using a simple and compact device. We conducted a parametric study using CAVCHEM, a computational model developed at Glenn, that simulates the cavitational collapse of a single bubble in a liquid (water) and the subsequent combustion of the gaseous contents inside the bubble. The model solves the time-dependent, compressible Navier-Stokes equations in one-dimension with finite-rate chemical kinetics using the CHEMKIN package. Specifically, parameters such as frequency, pressure, bubble radius, and the equivalence ratio were varied while examining their effect on the maximum temperature, radius, and chemical species. These studies indicate that the radius of the bubble is perhaps the most critical parameter governing bubble combustion dynamics and its efficiency. Based on the results of the parametric studies, we plan on conducting experiments to study the effect of ultrasonic perturbations on the bubble generation process with respect to the bubble radius and size distribution.

Corrigan, Jackie↗