SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This is the required paper summarizing the poster presentation material to be presented at The 25th European Microelectronics & Packaging Conference (EMPC 2025) (16 – 18 September 2025). The paper will be associated with the conference presentation in the conference proceedings
Coal tar is a condensed and recovered by-product of the coking of metallurgical coal for steel production. The heaviest fraction of distilled coal tar is an isotropic pitch largely used as a binder in the manufacturing of carbonaceous electrodes for primary aluminum smelting and in electric arc furnaces. Coal tar pitch offers high carbon yield upon carbonization. In this project, a process to convert the domestically sourced isotropic coal tar pitch, containing very low particulates (QI = 0.32 wt.%), to form flow-domain mesophase pitch amenable for melt spinning into precursor (green) fibers for carbon fiber, was developed and optimized. The final reproducible processing developed is reviewed in this report, along with several characterizations of the mesophase pitch. A final definition of the characteristics of a ‘spinnable’ mesophase pitch is presented. With this mesophase pitch, reproducible and stable multifilament melt spinning was developed, producing green fiber tows with filament diameters of approximately 20 m. The multifilament melt spinning was the most challenging aspect of the project and required the most effort. The best practices learned from this project for melt spinning are reviewed in this report. Once spun, the green fibers were oxidatively stabilized, carbonized and graphitized under inert gas atmosphere to form the final carbon fibers. Given the relatively high softening point of the mesophase pitch, no issues of interfilament fusion were observed during batch oxidation, and subsequent batch carbonization and graphitization went smoothly in all cases. An ~ 80 wt.% conversion of the green fiber mass to final carbon fiber was achieved. After graphitization, the carbon fibers showed high tensile moduli (most were ~ 600 GPa, or 87 Msi) consistent with commercially-available high-performance pitch-based carbon fiber. However, tensile strength and strain to failure were comparatively low. Further work to reduce defects in and on the fiber surfaces would increase these properties. SEM imaging of the graphitic fiber textures is presented herein. Rudimentary composites were fabricated from the carbon fibers and characterized showing similar modulus to baseline composites fabricated with commercial carbon fiber. Finally, a basic economic analysis was done showing the potential to increase the value of the isotropic coal tar pitch by up to 13.6 to 136 times based on a carbon fiber value of $\$$5/lb to $\$$50/lb, respectively. Moreover, the site case study suggests that the coal tar from the single integrated steel mill could supply production of up to 16 kt/yr of carbon fiber. Finally, a technological gap analysis was done which shed light on remaining technical challenges. These challenges included: recovery and utilization of condensates from the mesophase pitch processing, further advancing and increasing stability of the multifilament melt spinning processing, optimization of the oxidation processing, defect reduction for increased carbon fiber strength, and the development of a weaving process towards carbon fiber fabrics. To maximize the coal value chain, the primary objectives of this project were to (a) develop and scale efficient processing technology for producing melt-spinnable mesophase pitch from isotropic coal tar pitch, (b) clarify and simplify tedious continuous fiber processing technologies (particularly multifilament melt spinning of mesophase pitch) towards the efficient production of high performance carbon fiber, and (c) demonstrate and characterize representative composite parts derived from the final carbon fiber. Immense progress was made on all 3 objectives and is detailed in this report.
Coal is a versatile energy resource and was a driver of the industrial revolution that transformed the economies of Europe and North America and the trajectory of civilization. In this work, a technoeconomic analysis was performed for a coal-to-carbon-fiber manufacture process developed at the University of Kentucky’s Center for Applied Energy Research. According to this process, coal, with decant oil as the solvent, was converted to mesophase pitch via solvent extraction, and the mesophase pitch was subsequently converted to carbon fiber. The total cost to produce carbon fibers from coal and decant oil via the solvent extraction process was estimated to be $\$$11.50/kg for 50,000-tow pitch carbon fiber with a production volume of 3750 MT/year. The estimated carbon fiber cost was significantly lower than the current commercially available PAN-based carbon fiber price ($\$$20–$\$$30/kg). With decant oil recycling rates of 50% and 70% in the solvent extraction process, the manufacturing cost of carbon fiber was estimated to be $\$$9.90/kg and $\$$9.50/kg of carbon fiber, respectively. A cradle-to-gate energy assessment revealed that carbon fiber derived from coal exhibited an embodied energy of 510 MJ/kg, significantly lower than that of conventionally produced carbon fiber from PAN. This notable difference is primarily attributed to the substantially higher conversion rate of coal-based mesophase pitch fibers into carbon fiber, surpassing PAN fibers by 1.6 times. These findings indicate that using coal for carbon fiber production through solvent extraction methods could offer a more energy-efficient and cost-competitive alternative to the traditional PAN based approach.
This report documents activities carried out by Oak Ridge National Laboratory and by Ramaco Carbon LLC under CRADA project NFE-20-08273 entitled “Coal to Carbon Fibers.” This project’s main objective was the demonstration of commercially relevant utilization of coal as a precursor for high-value-added products, such as carbon fibers. The specific objectives included the following: • Deploy a production platform for the conversion of coal into carbon fibers in a way that utilizes preexisting base technologies and accelerates the commercialization of coal to carbon fibers. • Rapid deployment and utilization of versatile conversion test beds for accommodating preexisting base technologies for both the conversion of coal-to-pitch (proven donor solvent liquefaction techniques) and conversion of pitch-to-fiber (proven melt spun and melt blown techniques). Results from the generation of an isotropic pitch from a subbituminous coal through the low severity direct coal liquefaction process are presented. Carbon fibers were produced from this isotropic pitch through melt spinning and melt blowing.
The aim of this project is to reduce the cost of Type IV, carbon fiber (CF) composite overwrap compressed gas storage tanks by reducing the cost of CF and CF composites. The project team worked to reduce the cost of CF by exploring and testing opportunities for a low-cost alternative precursor material for CF production to supplant market-dominant and costly polyacrylonitrile (PAN). Concurrently, the team aimed to reduce the cost of the tanks at the composite level by improving the interfacial adhesion between the fibers and the matrix resin through the incorporation of low-cost nanoparticles recycled from waste materials, which would reduce the volume of costly CF required to achieve the same tank performance. At the end of the first year, the project team selected mesophase pitch as the primary precursor candidate from a field of materials based on the superior mechanical performance and cost-saving potential. During the second year, the team produced CFs derived from mesophase pitch achieving an average tensile strength of 365.6 ksi and average tensile modulus of 40.74 Msi. Facility availability for spinning and converting these fibers at greater scale has hindered scale-up demonstration, but the team has identified opportunities to conduct this work in the near term. Cost modeling shows that these mesophase pitch-derived CFs can be up to 40% less expensive than PAN-derived CFs due to the lower cost of the feedstock material, higher throughput, greater conversion yield, and lower cost spinning method and compared to PAN. Additionally, the team has demonstrated at lab-scale that nanoparticle coating CFs can significantly increase the interfacial shear strength and load transfer efficiency of CFs in a matrix. Single filament pull-out testing showed a 27% average increase in max interfacial shear strength due to this coating. A continuous method of applying these coatings to a tow of CF has been developed for scale-up. 26 m tows of coated CFs were produced using this system and formed into composite ring samples for ASTM ring burst testing. Issues with the testing protocol have limited assessment of these results. A prototype Type IV tank was designed to meet ANSI HGV2 standards, and the design criteria set out by DOE, using the CF properties developed by the team paired with a proprietary resin matrix, a polyamide liner, and aluminum end bosses. The tank weighs 153.1 kg and with a total capacity of 5.8 kg H2 (5.6 kg usable), which yields a gravimetric capacity of 1.17 kWh/kg. Cost modeling predicts that the tank will have a projected cost of $15.73/kWh. Tank performance modeling does not include considerations for fiber-matrix load transfer efficiency improvements offered by nanoparticle coating method.
Here, this study presents theoretical formulations to evaluate the fundamental parameters and performance characteristics of a bottom-raised oscillating surge wave energy converter (OSWEC) device. Employing a flat plate assumption and potential flow formulation in elliptical coordinates, closed-form equations for the added mass, radiation damping, and excitation forces/torques in the relevant pitch-pitch and surge-pitch directions of motion are developed and used to calculate the system's response amplitude operator and the forces and moments acting on the foundation. The model is benchmarked against numerical simulations using WAMIT and WEC-Sim, showcasing excellent agreement. The sensitivity of plate thickness on the analytical hydrodynamic solutions is investigated over several thickness-to-width ratios ranging from 1:80 to 1:10. The results show that as the thickness of the benchmark OSWEC increases, the deviation of the analytical hydrodynamic coefficients from the numerical solutions grows from 3% to 25%. Differences in the excitation forces and torques, however, are contained within 12%. While the flat plate assumption is a limitation of the proposed analytical model, the error is within a reasonable margin for use in the design space exploration phase before a higher-fidelity (and thus more computationally expensive) model is employed. A parametric study demonstrates the ability of the analytical model to quickly sweep over a domain of OSWEC dimensions, illustrating the analytical model's utility in the early phases of design.
Multi-material joining of lightweight structures is essential to reduce vehicle weight for more energy savings and less greenhouse gas emission. However, mismatch of thermal expansion coefficient for dissimilar materials during the paint baking process can induce part distortion and joint failure for adhesive bonding. Here, in the present work, a thermomechanical model based on contact mechanics and large deformation theory was developed for dissimilar high-strength Al alloy and steel components to study the distortion mechanism and influential factors of the residual gap. The established model was used to optimize joint conditions, such as pitch distance and part geometry. When a weld pitch is shorter than 100 mm, the maximum gap between Al and steel part can be greatly reduced to 0.1 mm, and the local stress and plastic strain around the joint during the oven heating and cooling cycle are also substantially reduced compared with the long pitch case (900 mm). The numerical modeling results revealed that a comparable bending stiffness ratio between the steel and Al cross sections is critical to the minimization of gap and distortion under paint baking condition. Digital image correlation technique was used to measure the overall part distortion and local strain distribution that were used to validate the model prediction. Weld bonding (adhesive bonding with friction bit joining) process was successfully employed to join Al to steel component without gap opening in adhesive after the paint baking and cooling.
Pixel tracking detectors at upcoming collider experiments will see unprecedented charged-particle densities. Real-time data reduction on the detector will enable higher granularity and faster readout, possibly enabling the use of the pixel detector in high-rate online event selection, such as the ATLAS or CMS first-level trigger systems. This data reduction can be accomplished with a neural network (NN) in the readout chip bonded with the sensor that recognizes and rejects tracks with low transverse momentum (p T ) based on the geometrical shape of the charge deposition (“cluster”). To design viable detectors for deployment, the dependence of the NN as a function of the sensor geometry, external magnetic field, irradiation, and noise must be understood. In this paper, we present first studies of the efficiency and data reduction for planar pixel sensors exploring these parameters. For the CMS HL-LHC sensor geometry, we obtain a signal efficiency of (91.9 ± 0.7)% and a data reduction of (29.7 ± 1.0)%. A smaller sensor pitch in the bending direction improves the p T discrimination, but a larger pitch can be partially compensated with detector thickness. Any accumulated radiation damage also changes the cluster shape, reducing the signal efficiency compared to the baseline by approximately 30–60% in absolute terms, but nearly all of the performance can be recovered through retraining of the network and updating the weights. Finally, the impact of noise was investigated, and retraining the network on noise-injected datasets was found to maintain performance within 6% of the baseline network trained and evaluated on noiseless data. •ASIC-compatible track-momentum classifier is robust in realistic detector conditions.•About 90% signal efficiency and 30% data reduction per layer for CMS HL-LHC geometry.•Single-layer signal efficiency increases for smaller pixel pitch or thicker sensors.•Performance with noise or after radiation damage mostly recovered by retraining.
In this work, laser ablation of Si electrode surfaces is utilized to provide localized strain relief during the Solid State Prealkylation of Electrode Architectures (SPEAR) process, in addition to volumetric expansion relief in the form of free volume channels across the electrode. A hexagonal mesh patterning was employed via laser ablation, where the hexagonal diameter (pitch) was varied from 250 to 1000 µm. It was demonstrated that these channels serve as expansion voids, accommodating the increase in electrode thickness observed during SPEAR and preventing cracking at the electrode surface. Optical microscopy and Raman mapping confirm that Li diffusion is the rate-limiting solid-state process, requiring a 24 h rest period to achieve homogeneous LixSi alloying through the electrode bulk. Electrochemical evaluations in full cells show that a 1000 μm pitch pattern yields a high initial discharge capacity of 2485 mA h g–1 and 86.4% capacity retention after 80 cycles, whereas smaller pitches (<500 μm) result in lithium plating at 4.1 V in full cells paired with NMC 811 due to excessive current collector exposure from the ablation process. XPS analysis reveals that the laser treatment modifies the electrode surface by increasing the Si–O and C–O species, changing the SEI composition observed via an increase in fluorophosphates upon cycling.
Electromagnetic Ion Cyclotron (EMIC) wave scattering has been proved to be responsible for the fast loss of both radiation belt (RB) electrons and ring current (RC) protons. However, its role in the concurrent dropout of these two co–located populations remains to be quantified. In this work, we study the effect of EMIC wave scattering on both populations during the 27 February 2014 storm by employing the global physics–based RAM–SCB model. Throughout this storm event, MeV RB electrons and 100s keV RC protons experienced simultaneous dropout following the occurrence of intense EMIC waves. By implementing data–driven initial and boundary conditions, we perform simulations for both populations through the interplay with EMIC waves and compare them against Van Allen Probes observations. Notably, the results indicate that by including EMIC wave scattering loss, especially by the He–band EMIC waves, the model aligns closely with data for both populations. Additionally, we investigate the simulated pitch angle distributions (PADs) for both populations. Including EMIC wave scattering in our model predicts a 90° peaked PAD for electrons with stronger losses at lower pitch angles, while protons exhibit an isotropic PAD with enhanced losses at pitch angles above 40°. Furthermore, our model predicts considerable precipitation of both particle populations, predominantly confined to the afternoon to midnight sector (12 hr < MLT < 24 hr) during the storm's main phase, corresponding closely with the presence of EMIC waves.
The objective of Phase III of the Offshore Code Comparison Collaboration, Continued, with Correlation and unCertainty (OC6) project was to validate the accuracy of aerodynamic load predictions by offshore wind modeling tools for a floating offshore wind turbine as it experiences large surge-translational and pitch-rotational motion, as would occur during normal operation. The test data considered were generated at Politecnico di Milano – a wind tunnel with a robotic excitation system to emulate wave loading on the wind turbine. Testing was performed using a scaled version of the DTU 10-MW reference model, and motion was prescribed as harmonic oscillations in the surge and pitch directions, independently. A variety of models were examined in the project, performing a three-way validation between engineering-level tools, higher-fidelity tools, and measurement data from two wind tunnel experimental campaigns. The Load Cases (LC) considered in this testing are as follows: LC 1.X - Steady Wind LC 2.X - Unsteady Wind - Surge Motion LC 3.X - Unsteady Wind - Pitch Motion Details on the results of the OC6 Phase III campaign can be found in the following reference: Bergua R., et al. OC6 project Phase III: validation of the aerodynamic loading on a wind turbine rotor undergoing large motion caused by a floating support structure, Wind Energ. Sci., 8, 465–485, https://doi.org/10.5194/wes-8-465-2023, 2023.
Campaign I of the Floating Offshore-wind Controls Advanced Laboratory Experimental Program (FOCAL) aims to generate a dataset enabling the validation of aerodynamic performance of a scaled turbine mounted on a rigid tower in a fixed condition. The turbine considered in the FOCAL testing campaigns is the IEA-Wind 15MW Reference Wind Turbine. This scaled model is capable of simulating advanced blade-pitch control strategies in a high-quality wind field. The turbine is fully instrumented to record a variety of parameters in real time such as structural loads and dynamics. The test data considered was generated at the University of Maine's Harold Alfond Wind and Wave (W2) testing facility. The Load Cases (LC) considered in this testing campaign are as follows: LC 1.X - Constant wind and blade-pitch with varying rotor speeds LC 2.X - Constant wind and rotor speed with varying blade-pitch LC 3.X - Varying wind with active closed-loop control Detailed properties on the modeled system are found in the following reference: Lenfest E., Floating Offshore-wind Controls Advanced Laboratory (FOCAL) Experimental Program - Campaign I: 1:70 Model-scale Testing of the IEA-Wind 15MW Reference Turbine. UMaine ASCC Report Number 23-40-1183. Details on the results of the verification and validation are found in the following reference: Mendoza, Nicole et al., "Verification and Validation of Model-Scale Turbine Performance and Control for the IEA Wind 15 MW Reference Wind Turbine," Energies, vol. 15, no. 20, 2022, https://doi.org/10.3390/en15207649.
The twist-bend nematic liquid crystal phase is a three-dimensional fluid in which achiral bent molecules spontaneously form an orientationally ordered, macroscopically chiral, heliconical winding of a ten nanometer-scale pitch in the absence of positional ordering. Here, the structure of the twist-bend phase of the bent dimer CB7CB and its mixtures with 5CB is characterized, revealing a hidden invariance of the self-assembly of the twist-bend structure of CB7CB, such that over a wide range of concentrations and temperatures, the helix pitch and cone angle change as if the ground state for a pitch of the TB helix is an inextensible heliconical ribbon along the contour formed by following the local molecular long axis (the director). Remarkably, the distance along the length for a single turn of this helix is given by 2πR mol , where R mol is the radius of bend curvature of a single all-trans CB7CB molecule. This relationship emerges from frustrated steric packing due to the bent molecular shape: space in the fluid that is hard to fill attracts the most flexible molecular subcomponents, a theme of nanosegregation that generates self-assembled, oligomer-like correlations of interlocking bent molecules in the form of a brickwork-like tiling of pairs of molecular strands into duplex double-helical chains. At higher temperatures in the twist-bend phase, the cone angle is small, the director contour is nearly along the helix axis z, and the duplex chains are sequences of biaxial elements formed by overlapping half-molecule pairs, with an approximately 45° rotation of the biaxis between each such element along the chain.
Abstract This work demonstrates that the electrodeposition of highly stressed films on compliant ribbons is a robust process to obtain helical structures with excellent mechanical stability and potentially high thermal and electrical conductance. Electrodeposition on end‐tethered ribbons alters their axial and bending stiffness while imparting mechanical stress to drive the formation of a helix with a microscale diameter and pitch in a controlled and scalable manner. The process generates helices with diameters and pitches between 80 and 200 µm and lengths as large as several millimeters. The approach is amenable to parallel processing a large number of 3D structures on any substrate, including large‐area semiconductor wafers. This phenomenon is explained in terms of the change of stress gradients as material is added. Applications of the fabricated helices include antennas, metamaterials, and slow‐wave structures in frequency ranges not previously attainable.
Ocean observation buoys require relatively small amounts of power, yet traditionally necessitate costly resupply trips for battery replacement. With the offshore location of the buoys and small power requirements, wave energy may be an effective solution for providing consistent and reliable power to support the buoy instrumentation. The US National Science Foundation Ocean Observatories Initiative (OOI) includes arrays of point absorber-like buoy systems used for ocean observation that have been deployed at multiple locations including the Southern Mid-Atlantic Bight. A study is currently underway to design a pitch resonator wave energy converter to supplement existing renewable energy generation for powering observation instrumentation. This paper details field measurements from surface moorings of the OOI Coastal Pioneer Array, which informs the subsequent development of a numerical model for the moored observation system. The model is developed in Wave Energy Converter Simulator (WEC-Sim), which leverages the Simscape multibody solver within the MATLAB/Simulink framework and linear potential flow theory to simulate the hydrodynamic interactions and multibody dynamics in 6 degrees of freedom. Multiple tuning variables are considered to produce a model for the system that matches well with empirical data (about 8% error). In conclusion, the WEC-Sim model will serve as a platform for integrating the pitch resonator wave energy converter concept and deployment preparation (detailed design including power take-off and control systems, response evaluation, etc.).
Here, this article presents a collaborative research campaign under the OC7 project on refining the engineering modeling approach for hydrodynamic viscous drag and damping on floating wind platforms, focusing on the adjustment of hydrodynamic drag and damping coefficients for different sea states. The participant simulation results show significant improvements over the previous OC6 project in predicting the low-frequency resonance motion under nonoperational conditions. The improvements are mainly due to enhanced modeling, including the adoption of wave stretching, and directly tuning the coefficients to measured platform motion in waves instead of free decay. For accurate predictions of mean- and slow-drift motion, the better performing models use a decreasing column splash zone drag coefficient and increasing surge damping/drag with increasing wave height. The model tuning for heave and pitch resonance shows less consistency. Generally, both quadratic drag and additional heave or pitch damping are needed for accurate predictions. Alternatively, a quadratic drag formulation with velocity filtering for the rectangular pontoons leads to improved predictions without additional damping. This model is also potentially more predictive, requiring minimal adjustment to its parameters for different conditions.
Resists that enable high-throughput and high-resolution patterning are essential in driving the semiconductor technology forward. The ultimate patterning performance of a resist in lithography is limited because of the trade-off between resolution, line-width roughness, and sensitivity; improving one or two of these parameters typically leads to a loss in the third. As the patterned feature sizes approach angstrom scale, the trade-off between these three metrics becomes increasingly hard to resolve and calls for a fundamental rethinking of the resist chemistry. Low-molecular-mass monodispersed metal-containing resists of high atom economy can provide not only very high resolution but also very low line-width roughness without sacrificing sensitivity. Here we describe a modular metal-containing resist platform (molecular mass <500 Da) where a molecular resist consists of just two components: a metal and a radical initiator bonded to it. This simple system not only is amenable to high-resolution electron beam lithography (EBL) and extreme ultraviolet lithography (EUVL) but also unites them mechanistically, giving a consolidated perspective of molecular and chemical processes happening during exposure. Irradiation of the resist leads to the production of secondary electrons that generate radicals in the initiator bonded to metal. This brings about an intramolecular rearrangement and causes solubility switch in the exposed resist. We demonstrate record 1.9–2.0 nm isolated patterns and 7 nm half-pitch dense line-space features over a large area using EBL. With EUVL, 12 nm half-pitch line-space features are shown at a dose of 68 mJ/cm 2 . In both of these patterning techniques, the line-width roughness was found to be ≤2 nm, a record low value for any resist platform, also leading to a low-performance trade-off metric, Z factor, of 0.6 × 10 –8 mJ·nm 3 . With the ultimate resolution limited by instrumental factors, potential patterning at the level of a unit cell can be envisaged, making low-molecular-mass resists best poised for angstrom-scale lithography.
Motional Stark effect polarimetry is a key diagnostic for plasma fusion research since its usage on PBX-M. The MSE diagnostic measures the radial magnetic pitch angle profile in a plasma from a neutral beam by observation of Stark split D-alpha emission from atoms excited by collision with ions and electrons in the plasma. The pitch angle measurement is used with equilibrium reconstruction codes to determine the q-profile for studies of plasma stability, confinement, and transport. Historically, the algorithm was used in a post-processing fashion. The goal of our work was to apply this method in real time and pass the results to the plasma control system computer for real-time equilibrium reconstruction and control.