SEARCH · Search NASA

Results for “plasma shape control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Characterization and controllability of radiated power via extrinsic impurity seeding in strongly negative triangularity plasmas in DIII-D

Experiments with extrinsic impurity seeding in strongly negative triangularity shapes in DIII-D achieved radiated power fractions (relative to input power) of up to ≈85% total radiation and ≈55% core radiation in steady-operating conditions. The relationship between core and total radiation was sensitive to impurity species and input power. Attempts to reach higher radiation levels via higher impurity flows resulted in radiative collapse disruptions. Nitrogen, neon, argon, and krypton were tested. Injection was by gas puffing, usually controlled by feeding back real-time estimates for core or total radiating fractions ($P_\textrm{rad} / P_\textrm{input}$). Argon and krypton were controlled by feeding back total radiating fraction, whereas neon was controlled by feeding back the core radiating fraction, due to the lower efficiency of neon as a divertor radiator. Nitrogen flows were pre-programmed. Reasonable total $P_\textrm{rad}$ control target following was achieved with argon or krypton. Control was more challenging with the neon/core radiation configuration, which was more prone to slow response and overshooting of the control target. Poor particle removal contributed to the control challenge: neon particle inventory within the last closed flux surface was roughly constant for up to 1 s (the longest duration tested) after neon injection was halted. However, separate experiments with laser-blow off of non-recycling impurities measured a short impurity confinement time, on the scale of the energy confinement time of ∼100 ms. Modeling with the Aurora impurity transport simulation matched experimental neon density profiles with full recycling (R = 1.0) and weak pumping but predicted rapid decreases in neon inventory if pumping were increased or recycling decreased. This indicates that changes outside the confined plasma (adding a well-placed pump) would improve controllability for all highly recycling species.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1982

Metals processing

The metals processing effort is directed towards improvement of performance and usefulness of materials through modification and control of shape and internal structure. Interaction of reactive gases, introduced into a plasma arc, with iron alloys were analyzed. The technology of magnesium production was assessed. The study of fast fluidized bed reactors is continued. Aspects of separation processes are being investigated. The development of high field superconducting composites for use in large magnetic fusion devices is also discussed. Processing, structure, and property relationships of superconducting materials and the substitution of precious metals in standard electrical contact and connector applications are tested. The influence of processing procedures on the structure of zircaloy and nickel base alloys with a goal of improving mechanical properties and performance is investigated. Investigation of the potential of metal insulator semiconductor junctions as photovoltaic devices is reported.

Source record↗

NASA NTRS2004

NASA Tech Briefs, February 2004

Topics include: Simulation Testing of Embedded Flight Software; Improved Indentation Test for Measuring Nonlinear Elasticity; Ultraviolet-Absorption Spectroscopic Biofilm Monitor; Electronic Tongue for Quantitation of Contaminants in Water; Radar for Measuring Soil Moisture Under Vegetation; Modular Wireless Data-Acquisition and Control System; Microwave System for Detecting Ice on Aircraft; Routing Algorithm Exploits Spatial Relations; Two-Finger EKG Method of Detecting Evasive Responses; Updated System-Availability and Resource-Allocation Program; Routines for Computing Pressure Drops in Venturis; Software for Fault-Tolerant Matrix Multiplication; Reproducible Growth of High-Quality Cubic-SiC Layers; Nonlinear Thermoelastic Model for SMAs and SMA Hybrid Composites; Liquid-Crystal Thermosets, a New Generation of High-Performance Liquid-Crystal Polymers; Formulations for Stronger Solid Oxide Fuel-Cell Electrolytes; Simulation of Hazards and Poses for a Rocker-Bogie Rover; Autonomous Formation Flight; Expandable Purge Chambers Would Protect Cryogenic Fittings; Wavy-Planform Helicopter Blades Make Less Noise; Miniature Robotic Spacecraft for Inspecting Other Spacecraft; Miniature Ring-Shaped Peristaltic Pump; Compact Plasma Accelerator; Improved Electrohydraulic Linear Actuators; A Software Architecture for Semiautonomous Robot Control; Fabrication of Channels for Nanobiotechnological Devices; Improved Thin, Flexible Heat Pipes; Miniature Radioisotope Thermoelectric Power Cubes; Permanent Sequestration of Emitted Gases in the Form of Clathrate Hydrates; Electrochemical, H2O2-Boosted Catalytic Oxidation System; Electrokinetic In Situ Treatment of Metal-Contaminated Soil; Pumping Liquid Oxygen by Use of Pulsed Magnetic Fields; Magnetocaloric Pumping of Liquid Oxygen; Tailoring Ion-Thruster Grid Apertures for Greater Efficiency; and Lidar for Guidance of a Spacecraft or Exploratory Robot.

Source record↗

DOE OSTI2023

Magnetic Energy Dissipation and γ-Ray Emission in Energetic Pulsars

Abstract Some of the most energetic pulsars exhibit rotation-modulated γ -ray emission in the 0.1–100 GeV band. The luminosity of this emission is typically 0.1%–10% of the pulsar spin-down power ( γ -ray efficiency), implying that a significant fraction of the available electromagnetic energy is dissipated in the magnetosphere and reradiated as high-energy photons. To investigate this phenomenon we model a pulsar magnetosphere using 3D particle-in-cell simulations with strong synchrotron cooling. We particularly focus on the dynamics of the equatorial current sheet where magnetic reconnection and energy dissipation take place. Our simulations demonstrate that a fraction of the spin-down power dissipated in the magnetospheric current sheet is controlled by the rate of magnetic reconnection at microphysical plasma scales and only depends on the pulsar inclination angle. We demonstrate that the maximum energy and the distribution function of accelerated pairs is controlled by the available magnetic energy per particle near the current sheet, the magnetization parameter. The shape and the extent of the plasma distribution is imprinted in the observed synchrotron emission, in particular, in the peak and the cutoff of the observed spectrum. We study how the strength of synchrotron cooling affects the observed variety of spectral shapes. Our conclusions naturally explain why pulsars with higher spin-down power have wider spectral shapes and, as a result, lower γ -ray efficiency.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2023

Spheroidization of Nd–Fe–B particles

Spherical powders are required for many advanced manufacturing techniques due to their inherent requirement of flowability, either within feed tubes or during powder spreading. As advanced manufacturing of magnets continues to develop, new production methods for feedstocks are also sought. Plasma spheroidization is a high-yield method to produce spherical Nd–Fe–B powders from irregularly shaped particles, with advantages including high throughput and a well-controlled size distribution. Highly spherical Nd–Fe–B powders with large scale production (i.e., kg) have been demonstrated using an inductively coupled thermal plasma system; however, the magnetic properties of the output powder display significant degradation. The coercivity was decreased from the initial 8 kOe (636 kA/m) of the as-received to 0.7 kOe (55 kA/m) for spheroidized powders. Microstructural investigation reveals 6% Nd depletion caused by the extreme temperatures of the plasma, leading to the formation of low-coercivity α-Fe and a subsequent decrease in energy product. In conclusion, post-spheroidization heat treatments with Nd can partially mitigate the coercivity degradation, increasing to 1.7 kOe (135 kA/m), potentially offering a pathway toward spherical powders for a range of applications.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Impact of electrode porosity architecture on electrochemical performances of 1 mm-thick LiFePO4 binder-free Li-ion electrodes fabricated by Spark Plasma Sintering

Thick electrodes with high active material loadings have been intensively studied over the last couple of decades in pursuit of achieving high energy density systems. To optimize and enhance the electrochemical performance of such electrodes, one has to control the pore morphology by, for example, varying the pore size and shape, and the level of porosity. In the present work, the fabrication of thick binder-free LiFePO4 (LFP) electrodes with two different pore sizes (12 and 20 mu m) and porosities (21 vol% and 44 vol%) using Spark Plasma Sintering (SPS) and templating approach is reported. The well-controlled porous architecture inside the thick electrodes is realized by fine-tuning experimental parameters. The impact of porosity architecture on electrochemical performance is quantified and correlated with the 3D tortuosity values determined from both micro-computed tomography and electrochemical impedance-based experimental methods. Based on the micro-computed tomography data analysis, estimated tortuosity values along X, Y, and Z axes reveal an anisotropic effect perpendicularly to the SPS compression axis (Z-direction). This is particularly profoundly observed in the samples with larger pores (20 mu m). The correlation between morphological properties and the rate capability performance is established indicating that the capacity loss happens mainly due to the Li-ion diffusion limitations.

Cathode material↗

DOE OSTI2022

Ultrabright Electron Bunch Injection in a Plasma Wakefield Driven by a Superluminal Flying Focus Electron Beam

Here, we propose a new method for self-injection of high-quality electron bunches in the plasma wakefield structure in the blowout regime utilizing a “flying focus” produced by a drive beam with an energy chirp. In a flying focus the speed of the density centroid of the drive bunch can be superluminal or subluminal by utilizing the chromatic dependence of the focusing optics. We first derive the focal velocity and the characteristic length of the focal spot in terms of the focal length and an energy chirp. We then demonstrate using multidimensional particle-in-cell simulations that a wake driven by a superluminally propagating flying focus of an electron beam can generate GeV-level electron bunches with ultralow normalized slice emittance (~30 nm rad), high current (~17 kA), low slice energy spread (~0.1%), and therefore high normalized brightness (> 10 19 A/ m 2 /rad 2 ) in a plasma of density ~10 19 cm –3 . The injection process is highly controllable and tunable by changing the focal velocity and shaping the drive beam current. Nearterm experiments at FACET II where the capabilities to generate tens of kA, < 10 fs drivers are planned, could potentially produce beams with brightness near 10 20 A / m 2 / rad 2 .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS2011

Optimization of Indium Bump Morphology for Improved Flip Chip Devices

Flip-chip hybridization, also known as bump bonding, is a packaging technique for microelectronic devices that directly connects an active element or detector to a substrate readout face-to-face, eliminating the need for wire bonding. In order to make conductive links between the two parts, a solder material is used between the bond pads on each side. Solder bumps, composed of indium metal, are typically deposited by thermal evaporation onto the active regions of the device and substrate. While indium bump technology has been a part of the electronic interconnect process field for many years and has been extensively employed in the infrared imager industry, obtaining a reliable, high-yield process for high-density patterns of bumps can be quite difficult. Under the right conditions, a moderate hydrogen plasma exposure can raise the temperature of the indium bump to the point where it can flow. This flow can result in a desirable shape where indium will efficiently wet the metal contact pad to provide good electrical contact to the underlying readout or imager circuit. However, it is extremely important to carefully control this process as the intensity of the hydrogen plasma treatment dramatically affects the indium bump morphology. To ensure the fine-tuning of this reflow process, it is necessary to have realtime feedback on the status of the bumps. With an appropriately placed viewport in a plasma chamber, one can image a small field (a square of approximately 5 millimeters on each side) of the bumps (10-20 microns in size) during the hydrogen plasma reflow process. By monitoring the shape of the bumps in real time using a video camera mounted to a telescoping 12 magnifying zoom lens and associated optical elements, an engineer can precisely determine when the reflow of the bumps has occurred, and can shut off the plasma before evaporation or de-wetting takes place.

Jones, Todd J.↗

NASA NTRS2005

Polymer based nanocomposites with nanofibers and exfoliated clay

Polymer solutions, containing clay sheets, were electrospun into nanofibers and microfibers that contained clay sheets inside. Controllable removal of polymer by plasma etching from the surface of fibers revealed the arrangement of clay. The shape, flexibility, size distribution and arrangement of clay sheets were observed by transmission and scanning electron microscopy. The clay sheets were partially aligned in big fibers with normal direction of clay sheets perpendicular to fiber axis. Crumpling of clay sheets inside fibers was observed when the fiber diameter was comparable to the lateral size of clay sheets. Single sheets of clay were observed both by catching clay sheets dispersed in water with electrospun nanofiber mats and by the deliberate removal of most of the polymer in the fibers. Thin, flexible gas barrier films, that are reasonably strong, were assembled from clay sheets and polymer nanofibers. Structure of composite films was characterized with scanning electron microscopy. Continuous film of clay sheets were physically attached to the surface of fiber mats. Spincoating film of polymer and clay sheets was reinforced by electrospun fiber scaffold. Certain alignment of clay sheets was observed in the vicinity of fibers.

Meador, Michael A.↗

DOE OSTI2025

Conceptual design of ELM control coils for the TCABR tokamak

An upgrade of the Tokamak à Chauffage Alfvén Brésilien (TCABR) is being designed to make it capable of creating a well controlled environment where the impact of resonant magnetic perturbation (RMP) fields on edge localised modes can be addressed over a wide range of (i) plasma shapes, (ii) divertor configurations, (iii) RMP coil geometries and (iv) perturbed magnetic field spectra. To this end, a unique set of in-vessel RMP coils is being designed and, in this work, their conceptual design is presented. This unique set of coils is composed of three toroidal arrays of coils on the low field side and three toroidal arrays of coils on the high field side. Each of these six toroidal arrays is composed of 18 coils thus allowing for the creation of RMP fields with toroidal mode numbers n ≤ 9 and with increased control of the poloidal mode number spectrum. To study dynamical effects of RMP fields of different toroidal mode numbers, all rotating simultaneously with different velocities, each of the 108 RMP coils will be powered independently by power supplies that can provide voltages of up to 4 kV and electric currents of up to 2 kA, with frequencies varying continuously from 0Hz up to 10kHz. A set of physical criteria were used to determine the optimal coil geometry and their respective number of turns to reduce the coil currents and voltages during operation with alternate current. Further, the conceptual design was carried out using both the vacuum approach (no plasma response) and the single-fluid response approach, which accounts for the response of a linear, single-fluid, visco-resistive plasma calculated using the M3D-C 1 code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Hybrid model predictive control techniques for safety factor profile and stored energy regulation while incorporating NBI constraints

Abstract A novel hybrid Model Predictive Control (MPC) algorithm has been designed for simultaneous safety factor ( q ) profile and stored energy ( w ) control while incorporating the pulse-width-modulation constraints associated with the neutral beam injection (NBI) system. Regulation of the q -profile has been extensively shown to be a key factor for improved confinement as well as non-inductive sustainment of the plasma current. Simultaneous control of w is necessary to prevent the triggering of pressure-driven magnetohydrodynamic instabilities as the controller shapes the q profile. Conventional MPC schemes proposed for q -profile control have considered the NBI powers as continuous-time signals, ignoring the discrete-time nature of these actuators and leading in some cases to performance loss. The hybrid MPC scheme in this work has the capability of incorporating the discrete-time actuator dynamics as additional constraints. In nonlinear simulations, the proposed hybrid MPC scheme demonstrates improved q -profile+ w control performance for NSTX-U operating scenarios.

Physics↗

NASA NTRS1982

On the flaring of cometary plasma tails

Assuming that hypersonic pressure balance with the solar wind governs the shape of plasma tails, it is found that the gas pressure of tail ions and the magnetic field strength at the flanks of the ionopause control the flaring state. The gas pressure exhibits the larger effect: for constant pressures above a certain critical value, the tail flares essentially without limit, while for smaller values the tail flares only near the head (becoming cylindrical at greater distances). The influence of the magnetic field is that the tail flares to larger distances the higher the field strength at the flanks of the ionopause. The observed variability in flaring (and the implied differences in gas pressure and magnetic field) are throught to be the result of changes in the position and shape of the sunward cometary ionopause. Insertion of reasonable comet and solar wind parameters into the pressure balance equations is found to give good agreement with the observations.

Ershkovich, A. I.↗

DOE OSTI2022

Spectral and temporal shaping of spectrally incoherent pulses in the infrared and ultraviolet

Laser–plasma instabilities (LPIs) hinder the interaction of high-energy laser pulses with targets. Simulations show that broadband spectrally incoherent pulses can mitigate these instabilities. Optimizing laser operation and target interaction requires controlling the properties of these optical pulses. We demonstrate closed-loop control of the spectral density and pulse shape of nanosecond spectrally incoherent pulses after optical parametric amplification in the infrared (∼1053 nm) and sum–frequency generation to the ultraviolet (∼351 nm) using spectral and temporal modulation in the fiber front end. The high versatility of the demonstrated approaches can support the generation of high-energy, spectrally incoherent pulses by future laser facilities for improved LPI mitigation.

47 OTHER INSTRUMENTATION↗

NASA NTRS2010

Review of Leading Approaches for Mitigating Hypersonic Vehicle Communications Blackout and a Method of Ceramic Particulate Injection Via Cathode Spot Arcs for Blackout Mitigation

Vehicles flying at hypersonic velocities within the atmosphere become enveloped in a "plasma sheath" that prevents radio communication, telemetry, and most importantly, GPS signal reception for navigation. This radio "blackout" period has been a problem since the dawn of the manned space program and was an especially significant hindrance during the days of the Apollo missions. An appropriate mitigation method must allow for spacecraft to ground control and ground control to spacecraft communications through the reentry plasma sheath. Many mitigation techniques have been proposed, including but not limited to, aerodynamic shaping, magnetic windows, and liquid injection. The research performed on these mitigation techniques over the years will be reviewed and summarized, along with the advantages and obstacles that each technique will need to overcome to be practically implemented. A unique approach for mitigating the blackout communications problem is presented herein along with research results associated with this method. The novel method involves the injection of ceramic metal-oxide particulate into a simulated reentry plasma to quench the reentry plasma. Injection of the solid ceramic particulates is achieved by entrainment within induced, energetic cathode spot flows.

Gillman, Eric D.↗

NASA NTRS2000

Currents and Flows in Distant Magnetospheres

Space scientists have explored, described, and explained the terrestrial magnetosphere for four decades. Rarely do they point out that the planetary and solar wind parameters controlling the size, shape, and activity of Earth's magnetosphere map out only a small portion of the space of dimensionless parameters that govern magnetospheric properties. With the discovery of Ganymede's magnetosphere, the range of parameters relevant to magnetospheric studies has grown by orders of magnitude. Consider the extremes of Ganymede's and Jupiter's magnetospheres. Jupiter's magnetosphere forms within a plasma flowing at super-Alfvenic speed, whereas Ganymede's forms in a sub-Alfvenic flow. The scale sizes of these magnetospheres, characterized by distances to the magnetopause of order 7x10(exp 6) km and 5x10(exp 3) km, respectively, differ by three orders of magnitude, ranging from 100 to 0.1 times the scale of Earth's magnetosphere. The current systems that control the structure and dynamics of a magnetosphere depend on specific plasma and field properties. Magnetopause currents at Ganymede differ greatly from the forms familiar for Earth and Jupiter, principally because the Mach number of the ambient plasma flow greatly influences the shape of the magnetosphere. A magnetodisk current, present at Jupiter because of its rapid rotation, is absent at Earth and Ganymede. The ring current, extensively investigated at Earth, is probably unimportant at Ganymede because the dynamical variations of the external flow are slow. The ring current is subsumed within the magnetodisk current at Jupiter. This paper describes and contrasts aspects of these and other current systems for the three bodies.

Kivelson, Margaret Galland↗

DOE OSTI2023

The influence of temperature history and flow mixing on the vapor-phase speciation of uranium oxide nanoparticles

The transport of radioactive material following a nuclear event depends heavily on fallout characteristics (e.g., composition, shape, and size), which in turn are controlled by the conditions under which the fallout forms. To this end, we use a novel plasma flow reactor (PFR) to explore how conditions including temperature history and gas mixing influence the chemical speciation and physical characteristics of uranium oxide nanoparticles. The PFR consists of a glass tube attached to an inductively coupled plasma (ICP) torch via an adaptor piece (ring flow injector) located downstream of the plasma-generating RF coil. We increase the gas flow rates from normal ICP operating conditions to higher values both upstream at the RF coil and downstream at the ring flow injector to create four distinct temperature profiles and two distinct gas flow mixing conditions (normal and higher Ar atomic ratios). Ex situ transmission electron microscopy (TEM) analysis is used to determine the crystal structure, morphology, and size distribution of the synthesized particles as a function of temperature and mixing. The particles display a striking dependence on these conditions in terms of the resulting speciation of uranium oxide: lower temperature (higher upstream) and slower cooling (normal downstream with normal Ar atomic ratio mixing) favor the formation of α-UO 3 particles, while faster cooling (higher downstream with higher Ar atomic ratio mixing) and higher temperature (normal upstream) favor the formation of UO 2 particles. The extent of gas mixing dictates particle aggregation: better mixing encourages the particles to aggregate more extensively. Here these results demonstrate the sensitivity of uranium to initial local conditions and can be used to improve our understanding of the kinetics that drive uranium speciation and ultimately inform fallout transport models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1972

Spectrocopic measurements of water vapor plasmas at high resolution: The optical transition probabilities for OH (A 2 Sigma - X 2 Pi)

Emission and absorption spectra of water vapor plasmas generated in a wall-stabilized arc at atmospheric pressure and 4 current, and at 0.03 atm and 15 to 50 A, were measured at high spatial and spectral resolution. The gas temperature was determined from the shape of Doppler-broadened rotational lines of OH. The observed nonequilibrium population distributions over the energy levels of atoms are interpreted in terms of a theoretical state model for diffusion-controlled arc plasmas. Excellent correlation is achieved between measured and predicted occupation of hydrogen energy levels. It is shown that the population distribution over the nonpredissociating rotational-vibrational levels of the A 2 Sigma state of OH is close to an equilibrium distribution at the gas temperature, although the total density of this state is much higher than its equilibrium density. The reduced intensities of the rotational lines originating in these levels yielded Boltzmann plots that were strictly linear.

Klein, L.↗

DOE OSTI2022

Investigation of core impurity transport in DIII-D diverted negative triangularity plasmas

Abstract Tokamak operation at negative triangularity has been shown to offer high energy confinement without the typical disadvantages of edge pedestals (Marinoni et al 2021 Nucl. Fusion 61 116010). In this paper, we examine impurity transport in DIII-D diverted negative triangularity experiments. Analysis of charge exchange recombination spectroscopy reveals flat or hollow carbon density profiles in the core, and impurity confinement times consistently shorter than energy confinement times. Bayesian inferences of impurity transport coefficients based on laser blow-off injections and forward modeling via the Aurora package (Sciortino et al 2021 Plasma Phys. Control. Fusion 63 112001) show core cross-field diffusion to be higher in L-mode than in H-mode. Impurity profile shapes remain flat or hollow in all cases. Inferred radial profiles of diffusion and convection are compared to neoclassical, quasilinear gyrofluid, and nonlinear gyrokinetic simulations. Heat transport is observed to be better captured by reduced turbulence models with respect to particle transport. State-of-the-art gyrokinetic modeling compares favorably with measurements across multiple transport channels. Overall, these results suggest that diverted negative triangularity discharges may offer a path to a highly-radiative L-mode scenario with high core performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗