SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
PEO restructures water near the polymer, reducing free volume and slowing local water.
Abstract Metal oxide‐based photoelectrodes for solar water splitting often utilize nanostructures to increase the solid‐liquid interface area. This reduces charge transport distances and increases the photocurrent for materials with short minority charge carrier diffusion lengths. While the merits of nanostructuring are well established, the effect of surface order on the photocurrent and carrier recombination has not yet received much attention in the literature. To evaluate the impact of pore ordering on the photoelectrochemical properties, mesoporous CuFe 2 O 4 (CFO) thin film photoanodes were prepared by dip‐coating and soft‐templating. Here, the pore order and geometry can be controlled by addition of copolymer surfactants poly(ethylene oxide)‐ block ‐poly(propylene oxide)‐ block ‐poly(ethylene oxide) (Pluronic® F‐127), polyisobutylene‐ block ‐poly(ethylene oxide) (PIB‐PEO) and poly(ethylene‐ co ‐butylene)‐ block ‐poly(ethylene oxide) (Kraton liquid™‐PEO, KLE). The non‐ordered CFO showed the highest photocurrent density of 0.2 mA/cm 2 at 1.3 V vs. RHE for sulfite oxidation, but the least photocurrent density for water oxidation. Conversely, the ordered CFO presented the best photoelectrochemical water oxidation performance. These differences can be understood on the basis of the high surface area, which promotes hole transfer to sulfite (a fast hole acceptor), but retards oxidation of water (a slow hole acceptor) due to electron‐hole recombination at the defective surface. This interpretation is confirmed by intensity‐modulated photocurrent (IMPS) and vibrating Kelvin probe surface photovoltage spectroscopy (VKP‐SPS). The lowest surface recombination rate was observed for the ordered KLE‐based mesoporous CFO, which retains spherical pore shapes at the surface resulting in fewer surface defects. Overall, this work shows that the photoelectrochemical energy conversion efficiency of copper ferrite thin films is not just controlled by the surface area, but also by surface order.
Cracks in catalyst layers (CLs) are a potential source of long-term failure in a fuel cell membrane electrode assembly (MEA). While modifications to the CL ink formulation can affect the degree of cracking, these changes may lead to lower initial performance than their cracked analogues due to the established link between formulation and performance. In this work, we explored the use of polymeric additives to mitigate CL cracks. Small quantities of poly (acrylic acid), poly (ethylene oxide), poly (methyl methacrylate), or poly (vinyl alcohol) - 5 wt% relative to ionomer mass - were added to the ink prior to its final mixing. Poly (vinyl alcohol) resulted in crack-free CLs, whereas the other polymers resulted in CLs with similar crack percentages as the control CL. Through a combination of transmission electron microscopy, X-ray computed tomography, and infrared spectroscopy, we ascribed the crack-mitigating mechanism of poly (vinyl alcohol) to its ability to hydrogen-bond with Nafion, the ion conducting polymer binder in the catalyst ink. Initial performance of this non-cracked electrode exhibited nearly identical electrochemical behavior to its cracked counterpart, demonstrating that PVA additives successfully reduce cracks while maintaining cell initial performance.
Poly(ethylene carbonate/ethylene oxide) P(EC/EO) copolymer was synthesized from EC monomer as a new matrix component of solid polymer electrolytes (SPEs), and the correlation between polymer dynamics and ionic conductivity in the P(EC/EO)-based SPEs at various lithium salt weight fractions (w Li ) was investigated by dielectric spectroscopy, rheology, and molecular dynamics (MD) simulations. With the addition of lithium salt, the molecular motions at various scales (i.e., from local to segmental and global motion scales) were found to change as follows: (i) the local motion of P(EC/EO) was slightly accelerated, and at w Li ≥ 0.22, it was separated into two relaxation modes, one faster and the other slower than that of P(EC/EO), (ii) the segmental motion of P(EC/EO) became significantly slower with the addition of lithium salt, and (iii) the global terminal relaxation became slightly slower with the increase of w Li . Thus, the motion of P(EC/EO) at various scales in SPEs changed with different trends with increasing lithium salt. It was also found that the temperature dependence of the ionic conductivity was described by a Vogel–Fulcher–Tammann-type function, which was correlated with the segmental motion, as is known in other SPE systems. Furthermore, from MD simulations, lithium ions are coordinated with the EC units more likely and with a closer distance than EO units in P(EC/EO), and the coordination number of oxygens around one lithium ion was estimated as 6–7 at the distance of 0.30 nm. Here, these results suggest that the coordination structure of the oxygens around the lithium ion is slightly disrupted due to the presence of EC units compared to the chelating structure of pure PEO electrolytes.
Hybrid organic-inorganic block copolymer electrolytes are of interest to enable batteries containing lithium metal anodes. The conductive block is a standard polymer electrolyte of poly(ethylene oxide) and the mechanically rigid block is an inorganic poly(acryloisobutyl polyhedral oligomeric silsesquioxane) polymer. Here, in this paper, we compare a poly(acryloisobutyl polyhedral oligomeric silsesquioxane)-b-poly(ethylene oxide)-b-poly(acryloisobutyl polyhedral oligomeric silsesquioxane) (POSS-PEO-POSS) triblock copolymer and a poly(ethylene oxide)-b- poly(acryloisobutyl polyhedral oligomeric silsesquioxane) (PEO-POSS) diblock copolymer mixed with lithium bis(trifluoromethanesulfonyl)imide salt. We have experimentally measured the limiting current density in lithium symmetric cells containing hybrid organic-inorganic electrolytes at 90 °C. The cells were polarized at a large range of applied current density. The diblock copolymer electrolyte exhibited a clear plateau in cell potential at all current densities below the limiting current density. At low applied current density, the triblock copolymer electrolyte also exhibited a clear plateau in cell potential. At currents approaching the limiting current density, the triblock copolymer electrolyte exhibited an underdamped potential profile. The cell potential did not reach a plateau at current densities above the limiting current in both systems. The diblock and triblock copolymer electrolytes were fully characterized using electrochemical methods to determine the ionic conductivity, cation current fraction, salt diffusion coefficient, and open circuit voltage as a function of salt concentration. Cell potential and salt concentration as functions of position in the cell at various current densities were calculated using Newman's concentrated solution theory. The theoretical limiting current density was calculated to be the current density at which salt is depleted at the cathode. We see quantitative agreement between experimental measurements and theoretical predictions for the limiting current density in the diblock copolymer electrolyte which has an ordered structure at all salt concentrations, while the experimental limiting current density is lower than the theoretical prediction for the triblock copolymer electrolyte, which exhibits a disordered morphology at high salt concentrations.
A simple approach was developed to computationally construct a polymer dataset by combining simplified molecular-input line-entry system (SMILES) strings of a targeted polymer backbone and a variety of molecular fragments. This method was used to create 14 polymer datasets by combining seven polymer backbones and molecules from two large molecular datasets (MOSES and QM9). Polymer backbones that were studied include four polydimethylsiloxane (PDMS) based backbones, poly(ethylene oxide) (PEO), poly(allyl glycidyl ether) (PAGE), and polyphosphazene (PPZ). The generated polymer datasets can be used for various cheminformatics tasks, including high-throughput screening for gas permeability and selectivity. This study utilized machine learning (ML) models to screen the polymers for CO2/CH4 and CO2/N2 gas separation using membranes. Several polymers of interest were identified. Here the results highlight that employing an ML model fitted to polymer selectivities leads to higher accuracy in predicting polymer selectivity compared to using the ratio of predicted permeabilities.
Single-ion conducting polymer blends (SICPBs) have demonstrated exceptional electrochemical performance as solid-state battery electrolytes; however, their nanoscale morphology and thermodynamic behavior remain unexplored. In this work, we investigate blends composed of deuterated poly(ethylene oxide) and poly[lithium sulfonyl(trifluoromethane sulfonyl)imide methacrylate], dPEO/P(LiMTFSI), and report the first experimental study of the nanostructures of charge-neutral polymer blends using small-angle neutron scattering (SANS) and small-angle X-ray scattering (SAXS). Despite the macroscopic miscibility indicated by a single glass-transition temperature, SANS and SAXS results reveal disordered, charge-correlated nanostructures that are strongly influenced by blend composition and temperature. At low concentrations of charge polymer, the scattering is dominated by concentration fluctuations, and the random phase approximation is applied to extract values of the Flory–Huggins interaction parameter, χ SC . At higher charged polymer content, concentration fluctuations are suppressed, and a correlation model is used to characterize the nanostructures of the charge correlations. We find that the structures of the charge correlations are highly dependent on blend composition─consistent with predictions from Sing’s self-consistent field theory-liquid state models. Understanding these features is essential for uncovering the ion transport mechanism that leads to improved electrochemical performance previously reported in SICPB systems.
Dendrites and dead lithium formation over prolonged cycling have long been challenges that hinder the safe implementation of metallic Li anodes. In this study, we employ polymer-stabilized liquid metal nanoparticles (LM-P NPs) of eutectic gallium indium (EGaIn) to create uniform Li nucleation sites enabling homogeneous lithium electrodeposition. Block copolymers of poly(ethylene oxide) and poly(acrylic acid) (PEO-b-PAA) were grafted onto the EGaIn surface, forming stabilized, well-dispersed NPs. Using a scalable spray coating approach, LM-P NPs were fabricated on copper current collectors, providing lithiophilic PEO sites and interactive carboxyl groups to guide Li deposition. The Li-EGaIn alloying process greatly reduced the Li + diffusion barrier, enabling fast Li transport through the coating layer, resulting in decreased nucleation overpotential. Therefore, about five times lower Li nucleation overpotential was obtained on the LM-P modified Cu with an optimal composition of the polymers than the bare Cu substrates. DFT computations was used to reveal the binding properties between the LM-P layer and Li. Due to the regulated Li plating/stripping process, as-obtained 30 μm Li anodes paired with LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM8 11 ) with a negative/positive electrode capacity (N/P) ratio ~ 10 exhibited stable cycling performance at 0.5C for over 250 cycles, with an average Coulombic efficiency of 99.55%. Ultrathin Li (1 μm) anodes with an N/P ratio ~ 0.6 were also demonstrated in Li|LiFePO 4 cells, which examined the stabilization of Li by LM-P NPs and monitored practical loadings of Li anodes that are close to anode-free systems.
This work aims to develop a detailed mechanistic understanding of the role of a graft polymer architecture on lithium ion (Li + ) transport in poly(ethylene oxide)-based polymer electrolytes. Specifically, we compare Li + transport in poly-(ethylene oxide) (PEO) versus poly(oligo oxyethylene methacrylate) (POEM) polymers doped with lithium bis( trifluoromethanesulfonyl) (LiTFSI) salts, using both experimental electrochemical characterization and molecular dynamics (MD) simulations. Furthermore, our results indicate that POEM exhibits a range of relaxation processes that cannot be interpreted solely in terms of glass-transition temperature (T g ) effects. Due to its side-chain architecture, the segmental relaxation of POEM is nonuniform across ether oxygens (EOs) and shows a more pronounced sensitivity to temperature above T g compared to PEO. Moreover, POEM also exhibits a nonuniform Li + coordination behavior, in which Li + is primarily solvated by two different chains in POEM, compared to a single chain in PEO. Li + transport in POEM occurs via two events with distinct characteristic times: a fast intrachain hopping along side chains and a slow interchain hopping between side chains. Taken together, the relaxation processes and ion transport mechanisms identified in POEM provide useful insights into design of more effective solid polymer electrolytes.
The design and engineering of composite materials is one strategy to satisfy the materials needs of systems with multiple orthogonal property requirements. In the case of rechargeable batteries with lithium metal anodes, the system requires a separator with fast lithium ion transport and good mechanical strength. In this work, we focus on the system polystyrene-block-poly(ethylene oxide) (SEO) with bis(trifluoromethane)sulfonimide lithium salt (LiTFSI). Ion transport occurs in the salt-containing poly(ethylene oxide)-rich domains. Mechanical rigidity arises due to the glassy nature of polystyrene (PS). If we assume that the salt does not interact with the PS-rich domains, we can describe ion transport in the electrolyte by three transport parameters (ionic conductivity, κ, salt diffusion coefficient, D, and cation transference number, t + 0 ) and a thermodynamic factor, T f . By systematically varying the volume fraction of the conducting phase, Φ c between 0.29 and 1.0, and chain length, N between 80 and 8000, we elucidate the role of morphology on ion transport. We find that κ is the strongest function of morphology, varying by three full orders of magnitude, while D is a weaker function of morphology. To calculate t + 0 and T f , we measure the current fraction, ρ + , and the open circuit potential, U, of concentration cells. We find that ρ + and U follow universal trends as a function of salt concentration, regardless of chain length, morphology, or Φ c , allowing us to calculate t + 0 for any SEO/LiTFSI or PEO/LiTFSI mixture when κ and D are known. Finally, the framework developed in this paper enables predicting the performance of any block copolymer electrolyte in a rechargeable battery.
This paper reports synthesis, structure, and properties of novel hybrid solid polymer electrolytes (SPE's) consisting of organically modified aluminosilica (OM-ALSi), formed within a poly(ethylene oxide)-in-salt (Li triflate) phase. To alter the structure and properties we fused functionalized silanes containing poly(ethylene oxide) (PEO) tails or CN groups.
Block polyethers comprised of poly(propylene oxide) (PPO) and poly(ethylene oxide) (PEG or PEO) segments form the basis of ABA-type PEO-b-PPO-b-PEO poloxamer materials. The inverse architecture with an internal hydrophilic PEO segment flanked by hydrophobic blocks can be difficult to prepare with control of architecture by use of traditional anionic polymerization. These oxyanionic polymerizations are plagued by chain-transfer-to-monomer side reactions that occur with substituted epoxides such as propylene oxide (PO). Herein, we report a new method for the preparation of block polymers through a controlled polymerization involving a N-Al Lewis adduct catalyst and an aluminum alkoxide macroinitiator. The Lewis pair catalyst was able to chain-extend commercial PEO macroinitiators to prepare di-, tri-, and pentablock polyethers with low dispersity and reasonable monomer tolerance. Chain extension was confirmed using size exclusion chromatography and diffusion ordered nuclear magnetic resonance spectroscopy. In conclusion, the resulting block polymers were additionally analyzed with small-angle X-ray scattering to correlate the morphology to molecular architecture.
We report on the nanoscale assembly of poly(lactic acid)-b-poly(ethylene oxide)-b-poly(lactic acid) (PLA-PEO-PLA) triblock copolymers in water, focusing on the effect of stereochemistry, where the PLA blocks are statistical copolymers of l-lactide and d-lactide with l/d ratios of 100/0, 95/5, 90/10, 85/15, 75/25, and 50/50. Small-angle neutron scattering (SANS) shows a nearly constant d-spacing as concentration varies in triblock systems with l/d ratios of 90/10 and 95/5, which we attribute to inhomogeneity in the structure of these gels, supported by previous USANS and confocal microscopy studies. The SANS data fit well to a core-shell ellipsoid form factor model with a hard-sphere structure factor. Polymeric micelles with l/d ratios from 75/25 to 85/15 displayed very high aggregation numbers, consistent with a strong interaction between PLA chains and the enhanced storage modulus observed in rheological studies of these systems. While the 90/10 and 95/5 samples showed lower aggregation numbers, their SANS profiles shows close spacing between micelles, which may promote a high fraction of intermicellar bridging chains, also consistent with a higher storage modulus. Overall, these results provide insight into the micellar assembly behavior of block copolymers with a crystallizable block, and indicate that tuning stereochemistry of PLA-based block copolymers is an effective means of modifying micellar properties for specific applications.
Here, we study the phase behavior of a triblock organic–inorganic hybrid copolymer, poly(polyhedral oligomeric silsesquioxane)-b-poly(ethylene oxide)-b-poly(polyhedral oligomeric silsesquioxane) (POSS-PEO-POSS)/lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt mixture, as a function of temperature. The polymer exhibits a lamellar morphology both in the neat state and in the presence of salt. However, the average grain size increases substantially when the electrolyte is heated above 113 °C. The grain structure of this sample changes reversibly with temperature, that is, smaller grains reappear when the electrolyte is cooled below 113 °C. While annealing block copolymers at high temperatures often leads to an increase in the grain size, this change is generally irreversible. The reason for the reversible change in the grain structure of the POSS-PEO-POSS/LiTFSI electrolyte is discussed. The ionic conductivity of the electrolyte also exhibits reversible changes in this temperature window. Knowledge of the grain structure is crucial for understanding ion transport in nanostructured electrolytes.
Abstract Carbon dioxide (CO 2 ) has been linked to many deleterious health effects, and it has also been used as a proxy for building occupancy measurements. These applications have created a need for low-cost and low-power CO 2 sensors that can be seamlessly incorporated into existing buildings. We report a resonant mass sensor coated with a solution-processable polymer blend of poly(ethylene oxide) (PEO) and poly(ethyleneimine) (PEI) for the detection of CO 2 across multiple use conditions. Controlling the polymer blend composition and nanostructure enabled better transport of the analyte gas into the sensing layer, which allowed for significantly enhanced CO 2 sensing relative to the state of the art. Moreover, the hydrophilic nature of PEO resulted in water uptake, which provided for higher sensing sensitivity at elevated humidity conditions. Therefore, this key integration of materials and resonant sensor platform could be a potential solution in the future for CO 2 monitoring in smart infrastructure.
Pluronic block copolymers, composed of poly(ethylene oxide) (PEO) and poly(propylene oxide) (PPO) in a triblock structure (PEO–PPO–PEO), are well known for their amphiphilic character and ability to self‐assemble into micelles in aqueous solution. The addition of ionic liquids (ILs) can further modulate the core–shell structures of these copolymers, influencing their stability, critical micellization temperature, and size. However, fully atomistic simulations often become prohibitively expensive due to the size and complexity of these systems. In this work, coarse‐grained simulations using a minimal implicit‐solvent model were performed to examine how two classes of ILs, namely, 1‐alkyl‐3‐methylimidazolium ([C n C 1 im]) and 1‐alkyl‐3‐methylpyrrolidinium ([C n C 1 pyrr]), change the micellization of Pluronic block copolymers in aqueous solution. The effects of IL concentration and alkyl group length were investigated, and the model greatly improved the efficiency of simulating large‐scale micelle systems. Furthermore, the numerical simulations are qualitatively compared with experimental investigations. Our results show that adding ILs expands the micelle core by embedding IL tails among the PPO blocks, thereby increasing overall micelle size. Less polar ILs generally induce more pronounced micellar growth. However, the effect of IL tail length on conformation and micellar packing is non‐monotonic. Up to moderate chain lengths (around C8–C10), the IL tails can extend sufficiently to increase local separation within the micelle; at longer tail lengths, enhanced hydrophobic clustering and steric hindrance cause the tails to bend or fold, capping further expansion. In addition, although block copolymer chains tend to pack more closely in the presence of longer‐tailed ILs, the random coil size of an individual polymer chain does not necessarily shrink. Meanwhile, these insights provide a deeper understanding of how Pluronic/IL systems interact, informing applications in drug delivery, cosmetics, food, and environmental engineering. Finally, our minimal implicit‐solvent model can be applied to larger systems and longer timescales, substantially reducing computational cost while reproducing key structural trends observed experimentally.
In many thin film materials, nuanced interplays of interfacial energies control the surface morphology and rearrangement. This work evaluates polymer−solvent interactions and solvent-driven surface reconstructions via ex situ and in situ fluid cell Atomic Force Microscopy (fc-AFM) analysis of amphiphilic block copolymer (BCP) thin films upon exposure to deionized (DI) water. We examine the differences in surface morphology, whole-film swelling, and force response in thin films of polystyrene-block-poly(ethylene oxide) (PS-b-PEO) and polystyrene- block-poly[(allyl glycidyl ether)-co-(ethylene oxide)] (PS-b- P[AGE-co-EO]) processed into standing-up cylinder morphologies perpendicular to a silicon substrate (⊥C). Using Amplitude Modulation AFM (AM-AFM) and Amplitude-Phase Distance (APD) force spectroscopy, this work probes the mechanoresponsive nature of the dynamic surface layers of these films, unveiling surface layer stratification and surface chain rearrangement via minimal tip−sample stimulation. To help rationalize the observed reconfigurations, the energetic driving forces were estimated using the harmonic mean approximations of interfacial energies. Given the nonionizable nature of the minority P(AGE-co-EO) block and the energetic driving forces for chain mobility, this work shows how the elimination of unfavorable PS−water interfaces drives chain rearrangement and coverage of the PS surface by chains of the hydrophilic block. This work highlights considerations for increasing the heterogeneity and complexity of BCP thin films via random blocks and how those changes to local interfacial energies may drive larger scale film morphology reconstructions, with broader implications for tuning interface hydrophilicity.
Block copolymer electrolytes (BCE) such as polystyrene-block-poly(ethylene oxide) (SEO) blended with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and composed of mechanically robust insulating and rubbery conducting nanodomains are promising solid-state electrolytes for Li batteries. Here, we compare ionic solvation, association, distribution, and conductivity in SEO-LiTFSI BCEs and their homopolymer PEO-LiTFSI analogs toward a fundamental understanding of the maximum in conductivity and transport mechanisms as a function of salt concentration. Ionic conductivity measurements reveal that SEO-LiTFSI and PEO-LiTFSI exhibit similar behaviors up to a Li/EO ratio of 1/12, where roughly half of the available solvation sites in the system are filled, and conductivity is maximized. As the Li/EO ratios increase to 1/5 the conductivity, of the PEO-LiTFSI drops nearly 3-fold, while the conductivity of SEO-LiTFSI remains constant. FTIR spectroscopy reveals that additional Li cations in the homopolymer electrolyte are complexed by additional EO units when the Li/EO ratio exceeds 1/12, while in the BCE, the proportion of complexed and uncomplexed EO units remains constant; Raman spectroscopy data at the same concentrations show that Li cations in the SEO-LiTFSI samples tend to coordinate more to their counteranions. Atomistic-scale molecular dynamics simulations corroborate these results and further show that associated ions tend to segregate to the SEO-LiTFSI domain interfaces. The opportunity for "excess" salt to be sequestered at BCE interfaces results in the retention of an optimum ratio of uncompleted and complexed PEO solvation sites in the middle of the conductive nanodomains of the BCE and maximized conductivity over a broad range of salt concentrations.