Search NASA⌕ Search

SEARCH · Search NASA

Results for “polycrystalline powders”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Removing Undesired Fine Powder From Silicon Reactor

Fluidized-bed reactor produces highly pure polycrystalline silicon particles with diameters approximately greater than 400 micrometers. Operates by pyrolysis of silane in reaction zone, which is bed of silicon seed particles fluidized by flow of silane and carrier gas. Above reaction zone, gas mixture flows rapidly enough to entrain silicon powders, but not larger seed and product particles. Entrained particles swept out of reactor. Applicable to other processes such as production of fine metal and ceramic powders where control of sizes of product needed.

Flagella, Robert N.↗
NASA NTRS1985

Slow plastic strain rate compressive flow in binary CoAl intermetallics

Constant-velocity elevated temperature compression tests have been conducted on a series of binary CoAl intermetallics produced by hot extrusion of blended prealloyed powders. The as-extruded materials were polycrystalline, and they retained their nominal 10-micron grain size after being tested between 1100 and 1400 K at strain rates ranging from 2 x 10 to the -4th to 2 x 10 to the -7th per sec. Significant plastic flow was obtained in all cases; while cracking was observed, much of this could be due to failure at matrix-oxide interfaces along extrusion stringers rather than to solely intergranular fracture. A maximum in flow strength occurs at an aluminum-to-cobalt ratio of 0.975, and the stress exponent appears to be constant for aluminum-to-cobalt ratios of 0.85 or more. It is likely that very aluminum-deficient materials deform by a different mechanism than do other compositions.

Whittenberger, J. D.↗
NASA NTRS1991

1000 to 1200 K time-dependent compressive deformation of single-crystalline and polycrystalline B2 Ni-40Al

The 1000-K and 1200-K time-dependent deformation of 100-line-oriented and non-100-line-oriented single crystals of Ni-40Al (made by a modified Bridgman technique) was examined over a large range of strain rates (from 0.1 to 10 to the -7th per sec). The results were compared with those for polycrystalline Ni-40Al made by hot pressing XD synthesized powder. The results from measurements of slow-plastic-strain-rate properties of the two materials show that single crystals offer no strength advantage over polycrystalline material. Both forms were found to deform via a dislocation climb mechanism.

Whittenberger, J. D.↗
NASA NTRS2009

Development of Ceramic Solid-State Laser Host Material

Polycrystalline ceramic laser materials are gaining importance in the development of novel diode-pumped solid-state lasers. Compared to single-crystals, ceramic laser materials offer advantages in terms of ease of fabrication, shape, size, and control of dopant concentrations. Recently, we have developed Neodymium doped Yttria (Nd:Y2O3) as a solid-state ceramic laser material. A scalable production method was utilized to make spherical non agglomerated and monodisperse metastable ceramic powders of compositions that were used to fabricate polycrystalline ceramic material components. This processing technique allowed for higher doping concentrations without the segregation problems that are normally encountered in single crystalline growth. We have successfully fabricated undoped and Neodymium doped Yttria material up to 2" in diameter, Ytterbium doped Yttria, and erbium doped Yttria. We are also in the process of developing other sesquioxides such as scandium Oxide (Sc2O3) and Lutesium Oxide (Lu2O3) doped with Ytterbium, erbium and thulium dopants. In this paper, we present our initial results on the material, optical, and spectroscopic properties of the doped and undoped sesquioxide materials. Polycrystalline ceramic lasers have enormous potential applications including remote sensing, chem.-bio detection, and space exploration research. It is also potentially much less expensive to produce ceramic laser materials compared to their single crystalline counterparts because of the shorter fabrication time and the potential for mass production in large sizes.

Prasad, Narasimha S.↗
DOE OSTI2022

Effect of disorder on thermodynamic instability of binary Rare-earth – Nickel – Palladium compounds

In this work, we have investigated the thermodynamic stability of disordered rare-earth phases SmX 2 and Sm 10 X 21 (X=Ni, Pd) using machine-learning based analytical descriptor and first-principles density functional theory methods. The absence of Laves phase compounds in R-Pd binary systems is a longstanding problem of rare earth science: even though Ni and Pd belong to the same group of the periodic table and have similar electronic structure, the Pd compound crystallizes in a monoclinic (C2/m) phase with 10:21 stoichiometry, i.e., Sm 10 Pd 21 , while the Ni compound adopts a cubic Laves phase (MgCu 2 ) structure. To understand this contrasting phase stability, we performed thermodynamic convex hull analysis of Sm x Ni 1-x and Sm x Pd 1-x binary systems, which is experimentally validated using powder X-ray diffraction (PXRD) analyzes of polycrystalline Sm(Ni x Pd 1-x ) 2 samples with x=0, 0.5, and 1. A detailed electronic-structure (band-structure, charge density, and Fermi-surface) analysis of the differences between SmNi 2 /SmPd 2 and Sm 10 Ni 21 /Sm 10 Pd 21 compounds provides the quantum mechanical origin of the unfavorable mixing of Pd with Ni in cubic Laves phase. We show that the stability of Sm-Pd in 10:21 stoichiometry arises from improved intra-/inter-layer 5d-4d bonding compared to the 1:2 stoichiometry. Our work emphasizes the importance of ab-initio methods and computationally inexpensive analytical descriptors for the detailed analysis of thermodynamic and electronic properties of hard-to-prepare rare-earth compounds.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Thermoelectric properties of n-type polycrystalline BixSb2-xTe3 alloys

(BixSbl-x)2Te3(.5 = x = .7) polycrystalline samples were synthesized using a combination of melting and powder metallurgy techniques. The samples were hot pressed in graphite dies and cut perpendicular and parallel to the pressing direction. Samples were examined by microprobe analysis to determine their atomic composition. The thermoelectric properties were measured at room temperature in both directions. These properties include Seebeck coefficient, thermal conductivity, electrical resistivity, and Hall effect. The thermoelectric figure-of-merit, ZT, was calculated fiom these properties.

thermoelectric power generation segmented↗
DOE OSTI2023

The T 2 structure of polycrystalline cubic human insulin

The polymorphism of human insulin upon pH variation was characterized via X-ray powder diffraction, employing a crystallization protocol previously established for co-crystallization with phenolic derivatives. Two distinct rhombohedral ( R 3) polymorphs and one cubic ( I 2 1 3) polymorph were identified with increasing pH, corresponding to the T 6 , T 3 R 3 f and T 2 conformations of insulin, respectively. The structure of the cubic T 2 polymorph was determined via multi-profile stereochemically restrained Rietveld refinement at 2.7 Å resolution. This constitutes the first cubic insulin structure to be determined from crystals grown in the presence of zinc ions, although no zinc binding was observed. The differences of the polycrystalline variant from other cubic insulin structures, as well as the nature of the pH-driven phase transitions, are discussed in detail.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

From Serendipity to Exploration: Synthesis and Properties of PtSiSb

PtSiSb is a compound with covalent Si–Sb bonds, which are relatively rare instances in solid-state materials. The original report on PtSiSb indicates synthetic challenges for the isolation of single-phase samples, as well as potential discrepancies in the predicted electronic structure and experimental transport properties. In this work, we considered PtSiSb as a case study with the objective of demonstrating the importance of synthesis as a bridge between theoretical predictions and experimental properties. Using guidance from in situ powder X-ray diffraction, the synthesis of single-phase polycrystalline samples was developed, allowing further experimental characterization of transport and catalytic properties. Thermal conductivity and heat capacity demonstrated anomalous behavior, indicating an unconventional phonon scattering mechanism in PtSiSb. Charge transport measurements indicated semimetallic behavior. Hydrogen evolution reaction (HER) tests in acidic electrolyte revealed that the PtSiSb cathode needs an overpotential η 10 = 120 mV to achieve a current density j = −10 mA/cm 2 . This is lower activity than elemental Pt but comparable to known and active transition-metal phosphide HER catalysts, such as CoP, with η 10 = 93 mV when measured at identical conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1978

Conductivity of materials made of aluminum nitride and silicon nitride mixtures

To establish the possible mechanism for conductivity in aluminum nitride a study was made of the electric conductivity of pure AlN and its mixtures with silicon nitride at different temperatures and partial pressures of nitrogen in the gas phase. The thermoelectromotive force was also measured. The experiments used polycrystalline samples of cylindrical shape 18 mm in diameter made of powders by hot pressing in graphite press molds at a temperature of 1973-2273 K and pressure 1,470,000 n/sqm. The items obtained by this method had porosity not over 5%. After pressing, the samples were machined to remove carbon from the surface, and were annealed in a stream of dry ammonia for 10 h at a temperature of 1273-1373 K. Electric conductivity was measured according to the bridge scheme on an alternating current of frequency 10 kHz. In order to guarantee close contact of the platinum electrodes with the surface of the samples, a thin layer of platinum was sprayed on them. Experiments were conducted in the temperature interval 1273-1573 K with a half hour delay at each assigned temperature with heating and cooling.

Gorbatov, A. G.↗
DOE OSTI2021

Toward In Situ Synchrotron Mapping of Crystal Selection Processes during Crystal Growth

In this work, we present an automated and rapid method for non-destructive mapping of crystal grains in a rod-shaped sample. The approach was designed for application to in situ float-zone crystal growth experiments at an x-ray synchrotron source, but could be useful in other applications. The methods have been tested on a TiO 2 boule grown in an optical float zone furnace. The approach applies a statistical filter to polycrystalline diffraction patterns on 2D detectors to rapidly determine the degree of powder-quality 1of the signal. When larger crystals emerge in the growth, their position, size and shape can be tracked using an automated blob-tracking algorithm that follows individual Bragg peaks as a function of position in a grid-scan, even when multiple crystals are contributing spots to diffraction images. This method is found to be robust as the same crystal shape can be independently reconstructed using different sets of Bragg reflections. Image segmentation methods are then used to map out the polycrystalline grains. We also note that other information about crystal quality, such as mosaicity or strain state, may be inferred and mapped from the intensity variation of the Bragg peaks at different locations within the sample.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural, Electronic, and Thermal Properties of CdSnAs 2

Structural, electrical, and thermal properties of CdSnAs 2 , with analyses from temperature-dependent transport properties over a large temperature range, are reported. Phase-pure microcrystalline powders were synthesized that were subsequently densified to a high-density homogeneous polycrystalline specimen for this study. Temperature-dependent transport indicates n-type semiconducting behavior with a very high and nearly temperature independent mobility over the entire measured temperature range, attributed to the very small electron effective mass of this material. The Debye model was successfully applied to model the thermal conductivity and specific heat. Furthermore, this work contributes to the fundamental understanding of this material, providing further insight and allowing for investigations into altering this and related physical properties of these materials for technological applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Ferrimagnetic Order in Tetragonal Antiperovskite Mn3GeN

The crystal and magnetic structures of the nitride antiperovskite M⁢n3⁢GeN reveals ferrimagnetic order stemming from a distorted kagome-derived lattice of the Mn atoms. Polycrystalline M⁢n3⁢GeN was synthesized via a solid-state reaction and characterized using neutron powder diffraction, dc magnetometry, and first-principles calculations. Rietveld refinement reveals near-stoichiometric composition (M⁢n3⁢Ge⁢N0.992⁢(7)) adopting a tetragonal 𝐼⁢4/𝑚⁢𝑐⁢𝑚 structure at 𝑇=500K and below, featuring axially distorted and tilted [NM⁢n6] octahedra that result in a buckled Mn kagome lattice. On heating, the tetragonal distortion and octahedral tilt angle decrease continuously before transitioning to the cubic 𝑃⁢𝑚⁢3⁢𝑚 antiperovskite phase at 𝑇≈527K. Neutron diffraction and magnetometry together reveal noncollinear ferrimagnetic ordering. For 30K≤𝑇≤500K, the magnetic structure is described by magnetic space group 𝐼⁢𝑏⁢𝑎′⁢𝑚′ (72.544), with inequivalent Mn1 and Mn2 sublattices that couple antiferromagnetically to yield a net moment. Density-functional theory-based calculations show that the different local moments originate from the bandwidths associated with distinct Mn–N bond lengths. Temperature-dependent refinements reveal distinct differences in the thermal disordering profiles of the Mn1 and Mn2 sublattices. These findings reveal a subtlety in the magnetic and structural behavior of M⁢n3⁢GeN, highlighting the interplay between structural distortions, magnetic ordering, and electronic structure in kagome-derived antiperovskite materials.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Influence of thermomechanical processing on elevated temperature slow plastic flow properties of B2 aluminide Fe-39.8at.% Al

A study of the elevated temperature slow plastic flow properties of the B2 aluminide Fe-39.8at.% Al was undertaken. Polycrystalline materials possessing several different microstructures were produced by the hot extrusion of prealloyed powder and, in some cases, postextrusion heat treatments. Compression tests were conducted in air at 1200, 1300 and 1400 K. Such testing revealed that the extrusion temperature affected the active deformation mechanisms where material extruded at 1505 K had a stress exponent about twice that of the intermetallic extruded at 1200 K. Grain size refinement to about 10 microns was found to strengthen the Fe-39.8at.% Al material; unfortunately, the effectiveness of such strengthening is limited to a homologous temperature of about 0.75 for strain rates of commercial interest (less than 10 to the -7th/sec).

Whittenberger, J. D.↗
NASA NTRS1995

Effect of Nb2O5 and V2O5 addition on the superconducting properties of YBa2Cu3O(y) thin films

The effect of Nb2O5 and V2O5 addition on the superconducting properties and microstructure of YBa2Cu3O(y) has been studied in thin films. Polycrystalline targets for laser ablation were prepared by mixing high purity V2O5 or Nb2O5 powders with a well characterized YBa2Cu3O(y) powder in the range 0 to 4 wt percent by solid state reaction method. Thin films (approximately 1500 A thickness) of the above targets were grown on (100) SrTiO3 (STO) and (100) LaAlO3 (LAO) substrates at 700 C temperature by pulsed laser deposition (PLD) technique. In the case of Nb2O5 addition we have noticed an increase in J(sub c) up to 0.5 wt percent and higher additive concentration (greater than 0.5 wt percent) have degraded the superconducting properties. However, in the case of V2O3 addition, there is an improvement in current density and microstructural properties up to 1 wt percent and the superconducting properties degrade for concentrations greater than 1 wt percent. The best J(sub c) for 0.5 wt percent of Nb2O5 added YBCO thin film is 1.6 x 10(exp 6) A/sq cm and for that of V2O5 added sample is 3.4 x 10(exp 6) A/sq cm at 77 K as compared to the pure YBa2Cu3O(y) (YBCO) film J(sub c) (1.2 x 10(exp 6) A/sq cm) observed on STO substrates. The reason for improvement in J(sub c) and microstructural properties in the case of V2O5 addition could be due to the low melting of V2O5 (690 C) which can act as a very good surfactant during deposition. Over all, we have realized that Nb2O5 addition or V2O5 addition to YBCO have shown significant improvement over the undoped YBa2Cu3O(7-x) films grown under identical conditions.

Srinivas, S.↗
DOE OSTI2021

Polycrystalline SnSe with a thermoelectric figure of merit greater than the single crystal

Abstract Thermoelectric materials generate electric energy from waste heat, with conversion efficiency governed by the dimensionless figure of merit, ZT. Single-crystal tin selenide (SnSe) was discovered to exhibit a high ZT of roughly 2.2–2.6 at 913 K, but more practical and deployable polycrystal versions of the same compound suffer from much poorer overall ZT, thereby thwarting prospects for cost-effective lead-free thermoelectrics. The poor polycrystal bulk performance is attributed to traces of tin oxides covering the surface of SnSe powders, which increases thermal conductivity, reduces electrical conductivity and thereby reduces ZT. Here, we report that hole-doped SnSe polycrystalline samples with reagents carefully purified and tin oxides removed exhibit an ZT of roughly 3.1 at 783 K. Its lattice thermal conductivity is ultralow at roughly 0.07 W m –1 K –1 at 783 K, lower than the single crystals. The path to ultrahigh thermoelectric performance in polycrystalline samples is the proper removal of the deleterious thermally conductive oxides from the surface of SnSe grains. These results could open an era of high-performance practical thermoelectrics from this high-performance material.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Additively-manufactured monocrystalline YBCO superconductor

Abstract Single-crystal microstructures enable high-performance YBa 2 Cu 3 O 7-x superconductors which are however limited to simple shapes due to their brittleness. Additive manufacturing can fabricate YBa 2 Cu 3 O 7-x superconductor with complex shapes, albeit with a polycrystalline microstructure. Here, we demonstrate a route to grow single-crystals from 3D-ink-printed, polycrystalline, sintered superconducting YBa 2 Cu 3 O 7-x (YBCO or Y123) + Y 2 BaCuO 5 (Y211), manufacturing objects with complex architectures displaying both high critical current density (J c =2.1 × 10 4 A . cm –2 , 77 K) and high critical temperature (T c = 88-89.5 K). An ink containing precursor powders (Y 2 O 3 , BaCO 3 , and CuO) is 3D-extruded into complex geometries and then reaction-sintered to obtain polycrystalline Y123 + Y211. A seed is then utilized to transform these 3D-printed parts from polycrystal to monocrystal via the melt growth method. The geometric details of 3D-printed parts survive the process without slumping, sagging or collapse, despite the long-term presence of liquid above the peritectic temperature. Origami structures can be created by sheet folding after 3D-printing. This additive approach enables the facile fabrication of superconducting devices with complex shapes and architectures, such as advanced undulator magnets to generate synchrotron radiation and microwave cavities for dark-matter axion search. This work highlights the potential of additive manufacturing for producing monocrystalline cuprate superconductors and opens the door to additive manufacturing of other monocrystalline functional ceramic or semiconductor materials.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Structural, vibrational, thermal, and magnetic properties of mullite-type NdMnTiO 5 ceramic

Mullite-type $R$Mn 2 O 5 ($R$ = Y, rare-earth element) ceramics are of ongoing research attention because of their interesting crystal-chemical and magnetic properties. We report nuclear and magnetic structures of NdMnTiO 5 together with its spectroscopic, thermogravimetric, and magnetic properties. The polycrystalline sample is prepared by solid-state synthesis and characterized from neutron and X-ray powder diffraction data Rietveld refinements. NdMnTiO 5 crystallizes in the orthorhombic space group $Pbam$ with metric parameter $a$ = 755.20(1) pm, $b$ = 869.91(1) pm, $c$ = 582.42(1) pm, and $V$ = 382.62(1) 10 6 pm 3 . The Mn 3+ and Ti 4+ cations are observed to be located in the octahedral and pyramidal sites, respectively. The vibrational features in these polyhedral sites are characterized by Raman and Fourier transform infrared spectroscopes. The higher decomposition temperature of NdMnTiO 5 , compared to other $R$Mn 2 O 5 phases, is explained in terms of the higher bond strength of Ti-O bonds than those of Mn-O bonds. Temperature-dependent DC magnetic susceptibility suggests a paramagnetic to antiferromagnetic phase transition at 43(1) K. Inverse susceptibility in the paramagnetic region above 120 K follows the Curie-Weiss law, resulting in a magnetic moment of 6.33(1) μ B per formula unit. Neutron diffraction data collected at 7.5 K reveal that the magnetic moments of Nd 3+ and Mn 3+ in NdMnTiO 5 are incommensurately ordered with a propagation vector $k$ = (0, 0.238, 0.117).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Real-space texture and pole-figure analysis using the 3D pair distribution function on a platinum thin film

An approach is described for studying texture in nanostructured materials. The approach implements the real-space texture pair distribution function (PDF), txPDF, laid out by Gong & Billinge {(2018). arXiv:1805.10342 [cond-mat]}. It is demonstrated on a fiber-textured polycrystalline Pt thin film. The approach uses 3D PDF methods to reconstruct the orientation distribution function of the powder crystallites from a set of diffraction patterns, taken at different tilt angles of the substrate with respect to the incident beam, directly from the 3D PDF of the sample. A real-space equivalent of the reciprocal-space pole figure is defined in terms of interatomic vectors in the PDF and computed for various interatomic vectors in the Pt film. Furthermore, it is shown how a valid isotropic PDF may be obtained from a weighted average over the tilt series, including the measurement conditions for the best approximant to the isotropic PDF from a single exposure, which for the case of the fiber-textured film was in a nearly grazing incidence orientation of ∼10°. Finally, an open-source Python software package, FouriGUI , is described that may be used to help in studies of texture from 3D reciprocal-space data, and indeed for Fourier transforming and visualizing 3D PDF data in general.

3D pair distribution functions↗