Search NASA⌕ Search

SEARCH · Search NASA

Results for “polymer electrode fuel cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

3D Printed Carbon Aerogels for Polymer-Electrolyte Fuel Cells

Carbon aerogels (CA) are known for ultra-low density, very high surface area, fine porous structure, and excellent electrical conductivity. Recent advances in high resolution 3D printing at LLNL enable the manufacturing of complex structured CA electrodes which have been demonstrated in electrolysis, flow battery, and supercapacitor applications. Polymer-electrolyte fuel cells (PEFC) may be an excellent candidate for these materials/methods as designers seek to optimize membrane-electrode assemblies to achieve higher efficiencies. A major challenge to PEFC design is two-phase flow due to water production which causes pore flooding and leads to cell instability and degradation. To mitigate these effects, groups have investigated the creation of liquid specific pathways in the porous layers to alleviate liquid buildup and enhance gas diffusion. While some progress has been made, traditionally manufactured GDLs, which consist of randomly distributed carbon fibers, are limiting. 3D printed CAs are a promising solution as complex macroporous electrode structures can be manufactured out of micro and nano porous filaments with a high level of control. Additionally, the process may allow for the consolidation of multiple layers (MPL, GDL, & flow channels) into a single printed architecture. In this work various CA lattice structures were printed using a direct ink write (DIW) method and liquid breakthrough pressures were measured to demonstrate the ability to tune the water pathways to achieve specific pressure thresholds. Furthermore, a discussion of the prospects for printed CA electrodes in PEFC will focus on material properties, synthesis techniques, and current challenges.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Recent developments in catalyst-related PEM fuel cell durability

Cost and durability remain the two major barriers to the widespread commercialization of polymer electrolyte membrane fuel cell (PEMFC)-based power systems, especially for the most impactful but challenging fuel cell electric vehicle (FCEV) application. Commercial FCEVs are now on the road; however, their PEMFC systems do not meet the cost targets established by the U.S. Department of Energy, primarily due to the high platinum loading needed on the cathode to achieve the requisite performance and lifetime. Furthermore, while the activities of a number of commercial Pt-based alloy cathode catalysts exceed the beginning-of-life (BOL) targets, these activities, and the overall cathode performance, degrade via a variety of mechanisms described herein. Degradation is mitigated in current FCEVs by utilizing a cathode catalyst with a lower BOL activity (e.g., much lower transition metal alloy content and larger BOL nanoparticle size), necessitating higher catalyst loadings, and through the utilization of system controls that avoid conditions known to exacerbate degradation processes, such as limiting the fuel cell stack voltage range. The design and development of active and robust materials and eliminating the need for vehicle mitigation strategies would greatly simplify the operating system, allowing for greater transient operation, avoiding large hybridization, and curtailing of fuel cell power. Although system mitigation strategies have provided the near-term pathway for FCEV commercialization, material-specific solutions are required to further reduce costs and improve operability and efficiency. Future material developments should focus on stabilization of the electrode structure and minimization of the catalyst particle susceptibility to dissolution caused by oxide formation and reduction over PEMFC cathode-relevant operating potentials plus minimization of support corrosion. Ex situ accelerated stress tests have provided insight into the processes responsible for material and performance degradation and will continue to provide useful information on the relative stability of materials and benchmarks for robust and stable materials-based solutions not requiring system mitigation strategies to achieve adequate lifetime.

25 ENERGY STORAGE↗
DOE OSTI2024

The impact of hot-press conditions on the durability of polymer electrolyte membrane fuel cells

The proton exchange membrane integrity can be compromised during hot-press fabrication of membrane electrode assemblies (MEAs) causing premature cell failures during operation. In this work, infrared (IR) thermography was used as a diagnostic tool to spatially visualize hydrogen (H 2 ) crossover and identify process-induced-membrane irregularities (PIMs). These irregularities were identified as seed locations for MEA failures. Fine tuning of hot-press conditions was used to mitigate premature cell failures informed by accelerated stress testing (AST). The impact of PIMs on the initial performance, high-frequency resistances, open-circuit voltage, and H 2 crossover are reported. Nafion XL and 212 membranes, hot-pressed with a force of 16 kg/cm 2 and temperature of 120°C, were found to be consistently irregularity-free. Irregularity-free MEAs using Nafion 211, 212, and XL membranes demonstrated AST lifetime improvements of 58, 64 and 400%, respectively, compared to those fabricated with non-optimized conditions. In conclusion, this work highlights the importance of fabrication parameters on premature cell failures.

08 HYDROGEN↗
DOE OSTI2023

Machine learning for optimizing the manufacture and operation of intermediate temperature fuel cells

The project developed machine learning and artificial intelligence (ML/AI) methodologies for guiding and accelerating the materials design and processing of new high temperature proton conducing electrode ionomer binders and reinforced membranes for high-temperature proton exchange membrane fuel cell (HT-PEMFC; aka intermediate-temperature polymer electrolyte membrane fuel cells).

08 HYDROGEN↗
DOE OSTI2025

PFSA-Ionomer Adsorption to C and Pt/C Particles in Fuel-Cell Inks

Catalyst inks used to make fuel-cell electrodes consist of Pt/C catalyst particles and a perfluorosulfonic acid (PFSA) ionomer dispersed in water/alcohol solvent mixtures. PFSA ionomer in the ink adsorbs to the surface of the catalyst particles, dictating the dispersion colloid properties. Following adsorption, the subsequent distribution of excess nonadsorbed ionomer in the ink then governs the final structure of the electrode. Here, we characterize the adsorption of the PFSA ionomer onto Pt/C catalyst particles. PFSA adsorption is largely irreversible. Adsorbed sulfonic-acid moieties impart a negative charge on the catalyst surface, causing electrostatic repulsion between the free ionomer in solution and the ionomer-covered Pt/C particle surface. The amount of adsorption is limited by the resulting electrostatic charge that grows as more ionomer adsorbs, and the catalyst surface becomes more negatively charged. Attenuating electrostatic repulsion by increasing the ink ionic strength promotes ionomer adsorption. Electrostatically limited adsorption is observed, irrespective of the solvent water/n-propanol ratio or the catalyst particle porosity and Pt loading. Experimentally measured ionomer adsorption isotherms are well predicted by a Smoluchowski-based kinetic adsorption model, in which the electrostatic energy barrier for adsorption is predicted from DLVO theory. These findings help to unravel the complex phenomena within these colloidal dispersions, allowing for subsequent tailoring of inks to optimize fuel-cell electrode structure and performance.

Adsorption↗
DOE OSTI2020

Proton exchange membrane fuel cells

Disclosed embodiments concern a membrane electrode assembly or a proton exchange membrane fuel cell comprising a phosphoric acid-doped polymeric membrane comprising a cationic functional group, such as an assembly or fuel cell having an ion exchange capacity of 0.8 to 3 mmol/gram and an operating temperature range of from 80° C. to 220° C. The cationic functional group can be any suitable functional group, such as ammonium, imidazolium, guanidinium, phosphazenium, sulfonium, oxonium, and phosphonium, with working embodiments typically using quaternary ammonium cationic functional groups tethered to the polymeric core. The polymeric material may be any suitable polymeric material, such as a material selected from polyaryl polymers, polyarylamides, polyimides, polystyrenes, polysulfones, polyethers, polyether sulfones, polyketones, polyetherketones, polyarylethers, polyolefins, and polynitriles. The membrane electrode assembly or a proton exchange membrane fuel cell can be used in any application now known or hereafter developed, such as a vehicle or a stationary power device.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Elucidating the Role of Ionomer in the Performance of Platinum Group Metal-free Catalyst Layer via in situ Electrochemical Diagnostics

The ionomer content in platinum group metal (PGM)-free polymer electrolyte fuel cell (PEFC) cathode catalyst layer (CCL) plays an important role in the electrode gas transport properties, proton conductivity, and hence, membrane electrode assembly (MEA) performance. In this work, the ionomer content in the CCL is varied, influencing electrode microstructure by altering porosity, tortuosity, as well as ionomer distribution and coverage of the catalyst particles. A novel technique consisting of a H 2 pump, combined with a Pt black sensor layer, is used to measure the bulk mass transport resistance of a series of PGM-free CCL prepared with different ionomer contents. The values for bulk electrode mass transport resistance are contrasted with electrode proton transport resistance in the cathode catalyst layer, establishing a clearly defined trade-off between two key performance limiting phenomena and identifying a need for novel PGM-free electrode fabrication strategies.

25 ENERGY STORAGE↗
DOE OSTI2021

Editors’ Choice—Examining Performance and Durability of Anion Exchange Membrane Fuel Cells with Novel Spirocyclic Anion Exchange Membranes

A series of spirocyclic copolymer membranes with varying ion exchange capacities (IECs) were investigated to probe the impact of polymer properties on in situ fuel cell performance and stability. In-situ electrochemical tests and post-mortem electron microscopy analysis of cross-sectioned membrane electrode assemblies (MEAs) have been combined with voltage loss breakdown analysis to evaluate the performance and degradation of different MEAs, and to probe the catalyst morphology and electrode structure at different stages of operation. Voltage loss breakdown results show that membrane degradation and kinetic losses played only a minor role in observed performance degradation and that performance losses were primarily related to increasing mass transport losses. From microscopy studies, carbon corrosion and Pt nanoparticle growth were identified at both the cathode and anode although more pronounced on the cathode resulting in significant structural changes. The membrane with the lowest IEC (1.3 mmolg −1 ) demonstrated the lowest peak power density ~ 1.16 W cm −2 , however, it showed the most stable performance (constant 0.6 A cm −2 hold) with ~ 5% degradation over 540 h. Isolation of performance losses and microscopic analysis of electrodes for anion exchange membrane fuel cells has not been reported previously, and these results help identify critical performance degradation concerns.

25 ENERGY STORAGE↗
DOE OSTI2022

Electrocatalysis of Oxygen Reduction Reaction in a Polymer Electrolyte Fuel Cell with a Covalent Framework of Iron Phthalocyanine Aerogel

Carbon aerogels have been studied in the context of fuel cell electrodes mainly as catalyst support materials due to their high surface area, porosity, and electrical conductivity. Recently, aerogels composed solely of inorganic molecular complexes have shown to be promising materials for the electrocatalysis of oxygen reduction reaction (ORR). These aerogels consist of atomically dispersed catalytic sites. Herein, we report on the synthesis and characterization of an aerogel-based catalyst: iron phthalocyanine aerogel. It was synthesized by coupling of ethynyl-terminated phthalocyanine monomers and then heat-treated at 800 °C to increase its electrical conductivity and catalytic activity. Further, the aerogels reported here were tested as catalysts for ORR in acidic conditions for the first time and found to have a ultra-high number of atomically dispersed catalytic sites (7.11 × 10 20 sites g –1 ) and very good catalytic activity (E onset = 0.9 V vs RHE and TOF = 9.2 × 10 –3 e – s –1 site –1 at 0.8 V vs RHE). The iron phthalocyanine aerogel was also studied in a proton exchange membrane fuel cell, reaching a peak power density of 292 mW cm –2 and an open circuit voltage of 0.83 V.

25 ENERGY STORAGE↗
DOE OSTI2026

A Relief Zone Architecture for Enhanced Durability of Ultrathin Membranes in Electrochemical Conversion Devices

Premature cell failures in electrochemical conversion systems often result when membrane electrode assemblies (MEAs) are prepared with ultra-thin (= 15 micrometer-thick) polymer electrolyte membranes (PEMs). These high-performance PEMs are susceptible to mechanical degradation from stress concentrations arising from component and device-level integration. Herein, a relief zone was developed to mitigate mechanical degradation by alleviating excess and non-uniform compression across the active area. Relief zones, created through the ablation of carbonaceous diffusion material achieves a seamless adaptation across a range of MEA dimensions and electrochemical applications without need for costly hardware modifications. This concept was demonstrated using fuel cells as a case study. Accelerated stress test (AST) validations yielded a 6-fold improvement for MEAs prepared with relief zones (i.e., lifetime approximately 1500 h) compared to those fabricated using conventional edge-protection techniques, showcasing the utility of this technique in decoupling integration and device-level engineering effects from intrinsic material limitations for durable electrochemical devices.

14 SOLAR ENERGY↗
DOE OSTI2021

Engineering block co-polymer anion exchange membrane domains for highly efficient electrode-decoupled redox flow batteries

We report, anion exchange membranes (AEMs) with high permselectivity, chemical stability and mechanical robustness are a key enabling technology for a variety of electrochemical energy conversion and storage systems such as fuel cells, redox flow batteries and water electrolyzers. Herein we examine well understood chemically stable triblock co-polymer AEMs derived by the chloromethylation (CM-) and subsequent trimethylamine (TMA) functionalization of polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS) block co-polymers. We show using small angle X-ray scattering (SAXS) that the introduction of a hydrophobic reinforcement matrix disrupts phase segregation and decreases ionic domain sizes in these AEM separators. The reinforcement matrix simultaneously causes the ultimate tensile strength (UTS) of the reinforced separator to increase by almost 600% compared to the unreinforced form, while maintaining comparable elasticity (ca. 500% elongation at break). Such reinforced r-SEBS30-TMA separators enable electrode-decoupled redox flow batteries (ED-RFBs) with significantly improved lifetimes by decreasing per cycle capacity fade from 0.5% to <0.05%. This 10× improvement in operando permselectivity opens the door to ED-RFBs employing inexpensive elemental actives achieving decades-long usable lifespans.

25 ENERGY STORAGE↗
DOE OSTI2023

ElectroCat: Platinum-Group-Metal-Free Engineered Framework Nano-Structure Catalyst (Final Technical Report)

Traditional synthesis methodologies that produce durable, highly active PGM-free electrocatalysts typically consist of a top-down approach utilizing a nitrogen-coordinating precursor, a metal precursor, and a support material. Nitrogen-coordinated transition metal complexes typically are absorbed onto a support material, which is then activated via high-temperature pyrolysis. Selection of the support and the nitrogen coordinating precursor has long been the focal point of efforts to maximize the number of accessible, catalytically active sites. In this project, GWE in collaboration with SRNL and NU will develop durable, highly active, low-cost, PGM-free electrocatalysts for polymer electrolyte membrane fuel cells designed and synthesized using a unique, bottom-up, rationally designed approach. Electrocatalysts are produced via polymerization reaction followed by a high-temperature pyrolysis step. Additionally, this project focuses on catalyst site and ORR mechanistic modeling to better understand the structure-property relationship.

08 HYDROGEN↗
DOE OSTI2024

Impact of polymer additives on crack mitigation of rod-coated fuel cell cathode catalyst layers

Cracks in catalyst layers (CLs) are a potential source of long-term failure in a fuel cell membrane electrode assembly (MEA). While modifications to the CL ink formulation can affect the degree of cracking, these changes may lead to lower initial performance than their cracked analogues due to the established link between formulation and performance. In this work, we explored the use of polymeric additives to mitigate CL cracks. Small quantities of poly (acrylic acid), poly (ethylene oxide), poly (methyl methacrylate), or poly (vinyl alcohol) - 5 wt% relative to ionomer mass - were added to the ink prior to its final mixing. Poly (vinyl alcohol) resulted in crack-free CLs, whereas the other polymers resulted in CLs with similar crack percentages as the control CL. Through a combination of transmission electron microscopy, X-ray computed tomography, and infrared spectroscopy, we ascribed the crack-mitigating mechanism of poly (vinyl alcohol) to its ability to hydrogen-bond with Nafion, the ion conducting polymer binder in the catalyst ink. Initial performance of this non-cracked electrode exhibited nearly identical electrochemical behavior to its cracked counterpart, demonstrating that PVA additives successfully reduce cracks while maintaining cell initial performance.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Solution-Deposited and Patternable Conductive Polymer Thin-Film Electrodes for Microbial Bioelectronics

Microbial bioelectronic devices integrate naturally occurring or synthetically engineered electroactive microbes with microelectronics. These devices have a broad range of potential applications, but engineering the biotic–abiotic interface for biocompatibility, adhesion, electron transfer, and maximum surface area remains a challenge. Prior approaches to interface modification lack simple processability, the ability to pattern the materials, and/or a significant enhancement in currents. We report a novel conductive polymer coating that significantly enhances current densities relative to unmodified electrodes in microbial bioelectronics is reported. The coating is based on a blend of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) crosslinked with poly(2-hydroxyethylacrylate) (PHEA) along with a thin polydopamine (PDA) layer for adhesion to an underlying indium tin oxide (ITO) electrode. When used as an interface layer with the current-producing bacterium Shewanella oneidensis MR-1, this material produces a 178-fold increase in the current density compared to unmodified electrodes, a current gain that is higher than previously reported thin-film 2D coatings and 3D conductive polymer coatings. The chemistry, morphology, and electronic properties of the coatings are characterized and the implementation of these coated electrodes for use in microbial fuel cells, multiplexed bioelectronic devices, and organic electrochemical transistor based microbial sensors are demonstrated. It is envisioned that this simple coating will advance the development of microbial bioelectronic devices.

patterned bioelectronics↗
DOE OSTI2023

High-Temperature Rotating Disk Electrode Study of Platinum Bimetallic Catalysts in Phosphoric Acid

Understanding the H 3 PO 4 effect on the catalyst’s activity under a relevant condition is important for high-temperature polymer electrolyte membrane fuel cell (HT-PEMFC) catalyst research. Here, we report a high-temperature rotating disk electrode (HT-RDE) study of oxygen reduction reaction (ORR) in H 3 PO 4 . With the regular electrochemical protocol, we found that H 3 PO 4 reduction could occur during cyclic voltammetry study and form a reductive species—phosphorus acid (H 3 PO 3 ). Further, to obtain reliable ORR measurement, we optimized the protocol to avoid the H 3 PO 3 generation. The ORR activity of carbon-supported PtM (M = Fe, Co, Ni, Ru, Pd, and Ir) bimetallic alloy catalysts measured with this HT-RDE method showed higher ORR activity than Pt. To understand the alloying effect, we combine experiments in diluted solutions to distinguish the alloying effect on Pt–O binding and Pt–H 3 PO 4 binding. The results indicate that H 3 PO 4 mainly reduces available sites for ORR, with little effect on neighboring site’s Pt–O binding via Pt–H 3 PO 4 interaction, which is also supported by the density functional theory calculation of the Pt–O binding energy with/without H 2 PO 4 . Further study in a phosphoric acid-doped quaternary ammonium-biphosphate ion pair coordinated polyphenylene (PA-QAPOH) membrane electrode assembly (MEA) shows that the active alloy catalyst has better performance in both the HT-RDE and MEA. Also, the MEA gives higher ORR activity than the HT-RDE because of the higher pressure and less phosphoric acid content of the MEA. Yet, the gap between the HT-RDE and MEA is significantly smaller than that between the room temperature (RT)-RDE and MEA, suggesting the importance of temperature and H 3 PO 4 concentration in understanding ORR in HT-PEMFCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Impact of Platinum Primary Particle Loading on Fuel Cell Performance: Insights from Catalyst/Ionomer Ink Interactions

A variety of electrochemical energy conversion technologies, including fuel cells, rely on solution-processing techniques (via inks) to form their catalyst layers (CLs). The CLs are heterogeneous structures, often with uneven ion-conducting polymer (ionomer) coverage and underutilized catalysts. Various platinum-supported-on-carbon colloidal catalyst particles are used, but little is known about how or why changing the primary particle loading (PPL, or the weight fraction of platinum of the carbon-platinum catalyst particles) impacts performance. Here, by investigating the CL gas-transport resistance and zeta-potentials of the corresponding inks as a function of PPL, a direct correlation between the CL high current density performance and ink zeta-potential is observed. This correlation stems from likely changes in ionomer distributions and catalyst-particle agglomeration as a function of PPL, as revealed by pH, zeta-potential, and impedance measurements. These findings are critical to unraveling the ionomer distribution heterogeneity in ink-based CLs and enabling enhanced Pt utilization and improved device performance for fuel cells and related electrochemical devices.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Determining Proton Transport in Pseudo Catalyst Layers Using Hydrogen Pump DC and AC Techniques

Optimizing electrode morphology with a more uniform ionomer distribution is key to reducing ohmic losses and increasing electrocatalyst utilization in polymer electrolyte fuel cells (PEFCs). Inherent ionomer conductivity, volume fraction and tortuosity determine effective ionic conductivity. We use hydrogen pump (HP) method to measure effective ionic conductivity of a pseudo catalyst layer (PCL) comprised of Vulcan XC-72 carbon black and 3M 825 EW ionomer with ionomer to carbon (I/C) ratios of 0.6, 1 and 1.4 and relative humidity (RH) range of 50 to 120%. These direct current (DC) experiments are then compared with electrochemical impedance spectroscopy (EIS). Both DC and EIS methods show good agreement, indicating that EIS can be used as an alternative to DC method in HP experiment. Ionic conductivity for PCL with I/C of 1 and 1.4 was found to be about one order of magnitude higher than I/C of 0.6 for most of the RH range. At 90% RH tortuosities for I/C = 1 and 1.4 were close to 1, whereas tortuosity for I/C = 0.6 was 3. With decrease in relative humidity tortuosities increased linearly and at 50% relative humidity a PCL with I/C = 0.6 had the highest tortuosity of 6.1.

25 ENERGY STORAGE↗
DOE OSTI2023

Crack detection in fuel cell electrodes using a spatial filtering technique for overcoming noisy backgrounds

Image processing is a powerful tool that allows for rapid and automated data parsing in settings that occupy large variable spaces and require large data sets. Feature detection on difficultly discerned backgrounds is a subset of image processing that facilitates the extraction of quantitative metrics from otherwise subjective data. Crack detection and quantification is an important capability in polymer electrolyte membrane fuel cell quality control, failure analysis, and optimization. This work presents a technique to perform crack detection and quantification which overcomes challenges faced by commonly used image segmentation techniques. We demonstrate the use of a geometrically filtered noise‐level detection technique to select a binary threshold value from which we then quantify how cracked a sample is. Furthermore, we demonstrate the accuracy of our technique using programmatically generated test images of known crack amounts and their performance on real‐world fuel cell catalyst layer samples.

30 DIRECT ENERGY CONVERSION↗