Search NASA⌕ Search

SEARCH · Search NASA

Results for “polypropylene”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Polypropylene Composites Reinforced With Recycled Waste Cellulosic Fiber/Fine Mixture: The Impact of Cellulose Sieving on Performance

This study explores how a sieving step of waste cellulosic fiber and fine (WCFF) mixture affects the performance of WCFF‐loaded polypropylene (PP) composites and whether the separation of fines from fibers offers an added benefit. The WCFF samples were downsized, and four different filler size ranges were sieved using a series of mesh sizes from 4 to 0.85 mm. The WCFF/PP composites were then compounded at 20 wt.% loading of WCFF using a twin‐screw extruder. Incorporating WCFF increased the tensile strength to 41.28 MPa and the modulus to 3207 MPa, accounting for 28% and 38% enhancements, respectively. Interestingly, the greatest improvements were associated with the nonsieved WCFF case, and the sieved WCFF fibers provided only marginal enhancements over virgin PP. The outperformance of nonsieved WCFF was attributed to the synergistic reinforcement of hybrid fibers and fines as well as the maintenance of longer fibers in the system. However, the strain at break and impact strength of PP decreased after introducing WCFF. Moreover, the complex viscosity and storage modulus increased with an increase in the filler size, due to the formation of a more effective percolative network. The PP's crystallinity exhibited a relatively strong dependency on the sieving, where WCFF samples with short‐aspect‐ratio fillers promoted the crystallinity significantly. It was also found that the WCFF degradation onset temperature increased once it was incorporated into PP. This study suggests that waste cellulosic feedstocks can be utilized as a reinforcement without additional sieving to manufacture high‐performance and cost‐effective composites.

36 MATERIALS SCIENCE↗

A Spatially Resolved Evaluation of Accelerated Environmental Aging on Emerging Polypropylene-Based Photovoltaic Backsheets Using Raman Spectroscopy

For this work, accelerated aging was used to assess environmental degradation in emerging co-extruded polypropylene (PP)-based backsheets under three different environmental conditions (65°C/20% relative humidity (RH), 75°C/20% RH, and 75°C/50% RH). Although differential scanning calorimetry did not measure crystallinity changes with exposure, spatially resolved Raman spectroscopy identified crystallinity increases in the core layer of aged samples, indicating a heterogeneous postcrystallization process. The Raman results were in agreement with synchrotron-based microfocused wide-angle X-ray scattering measurements. Cross-sectional nanoindentation was used to correlate localized crystallinity shifts with changes in Young's modulus. A similar trend was found where increased modulus was measured in the core layer, supporting the relationship between modulus and crystallinity. Finally, dielectric characterization was used to assess the impact of these material property changes on performance. While changes in the backsheet material properties and dielectric performance were observed with accelerated aging, these shifts generally equilibrated with time, indicating overall stability in response to environmental stressors. Additionally, the identified heterogeneous material property changes indicate that spatially resolved crystallinity measurements may be a valuable early failure indicator to be used in the assessment of PV backsheet long-term durability.

36 MATERIALS SCIENCE↗

Investigation of Polypropylene-Montmorillonite Clay Nanocomposite Films Containing a Pro-degradant Additive

This paper investigates the performance of polypropylene (PP) incorporated with montmorillonite (MMT) nanoclay, maleic anhydride grafted PP (PP-g-MAH), and pro-degradant additive (TDPA®), which provides additional benefits of increasing biodegradability. A twin-screw extruder was used to compound PP, MMT, PP-g-MAH, and TDPA, and the extruded nanocomposite films were collected for testing, and their mechanical, thermal, barrier, oxo-biodegradability, and morphological properties were evaluated. Tensile test, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), oxygen permeability test, soil burial test, X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscope (SEM) analysis were used to investigate these properties. Increasing MMT content from 1 to 3 phr increases tensile strength and Young’s modulus of the neat PP samples up to ca.45% and 27% respectively. Improvement of thermal properties for neat PP samples was observed by increasing MMT content from 1 to 3 phr. However, at 4 phr MMT content, both mechanical and thermal properties of nanocomposites dropped slightly. For soil buried samples, DSC and TGA results revealed significant changes in the thermal properties for PP samples containing TDPE additive compared to neat PP, clearly confirming the effectiveness of this TDPA additive in promoting oxo-biodegradation process of PP. Similarly weight loss evaluation result shows that about 4% weight loss for sample (PP/TD), which is PP and TDPA blend only, compared to neat PP. However, increasing MMT content from 1 to 4 phr slightly reduced weight loss of PP from 3.5 to 1.5%, respectively, for 6 month soil exposure period, which indicates that increasing MMT content was detrimental to the degradation process. For higher MMT content, the oxygen permeability of PP nanocomposites was decreased by 46% of the corresponding values for neat PP. The XRD and TEM results confirmed the exfoliation structure of the nanocomposites. The morphological change after soil burial test was studied using scanning electron microscopy (SEM).

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Preparation and Determination of Antimicrobial Property of Cation-Exchanged Ecuadorian Natural Zeolite to be Used as Filler for Polyethylene and Polypropylene Matrices

Zeolites are crystalline aluminosilicates with nanoporous structure, tasteless and non-toxic materials. In this study, silver ion-exchanged zeolite, which was prepared from the natural Ecuadorian zeolites was used as reinforcement material in low-density polyethylene (LDPE) and polypropylene (PP). Polymers were filled with 1, 2 and 3 wt% concentrations of natural zeolite (Z) and silver ion exchanged zeolite (ZA). Zeolites and composites were characterized by X-ray diffractometry, Fourier transform infrared spectroscopy, scanning electron microscope, thermogravimetric analysis and mechanical analysis techniques. Microbiological analysis of silver ion exchanged zeolite showed effective antibacterial property against Escherichia coli bacteria. PP/ZA composites showed better tensile strengths in all mixes comparing to pure PP. ZAPE2 and ZAPP1 showed the best mechanical properties among all the composites based on polyethylene and PP, respectively. The composites prepared are potential candidates to be used in food packaging, and ZA type zeolites can be used as filler for the preparation of various composites.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Titania-Containing Recycled Polypropylene Surfaces with Photo-Induced Reversible Switching Wettability

Creation of smart surfaces with reversible wettability has always fascinated researchers over the past years but complicated methods are still employed. This study reports a facile and environment-friendly fabrication of smart composite coatings from recycled polypropylene (PP) plastics in which titanium dioxide or titania particles are added to impart extreme anti-wettability with improved thermal stability. The method used is simple and economical as the utilization of used PP plastics can positively impact to the volume reduction of plastic waste in the environment. Titania, being photo-responsive, makes the wetting behavior switch reversibly (i.e. from being superhydrophobic to hydrophilic and vice versa) by employing ultraviolet light as a stimulus and storage in the dark for superhydrophobicity restoration. Combined with relatively high thermal stability, the PP/TiO{sub 2} composites are thought to be useful not only as smart coatings but also for a wide variety of barrier-related applications.

36 MATERIALS SCIENCE↗

Pro-Degradant Effect of Talc Nanoparticles on Polypropylene Films

Pro-degradant effect of talc nanoparticles on degradation process of polypropylene (PP) films was studied. For this purpose, two talc minerals having different intrinsic characteristics and iron content were used. Films with 0, 1 and 5% w/w of talc were exposed to three different weathering scenarios: indoor, outdoor and accelerated aging. The extent of degradation in films was evaluated by analyzing chemical and surface structure as well as optical, thermal and mechanical properties. The presence of talc induced a greater degradation in nanocomposite films and this phenomenon was increased with nanoparticle concentration. Samples having talc with higher iron content were more affected by weathering conditions since iron impurities acted as promoters of the degradation process. Clearly, iron impure talc is a good environmentally friendly alternative as a pro-degradant additive for PP degradation as its low cost (less than PP) and sustainability since does not contain heavy metals.

36 MATERIALS SCIENCE↗

Development of Green Composites Based on Polypropylene and Corncob Agricultural Residue

Green composites of polypropylene (PP) and corncob (CCB) agricultural residue with CCB content ranging from 5 to 30 wt% were compounded by melt extrusion and their properties investigated by density measurements, thermogravimetric analyses, differential scanning calorimetry, scanning electron microscopy (SEM) and tension, flexural and impact properties. Properties were dependent on CCB content. SEM micrographs showed that PP/CCB composites are composed of all layers of the corncob, but with a higher content of woody ring and pith. Composites with CCB up to 20 wt% presented particles evenly dispersed into PP matrix and density values ranging from 0.929 to 1.026 g/cm{sup 3}. Thermal analyses showed that CCB is thermally stable up to 200 °C, ensuring that no degradation took place during processing, and PP/CCB composites are more crystalline than neat PP. Tensile strength and elongation at break of the composites decreased respectively from 30 to 20 MPa, and 22.7 to 3.7%, and the elastic modulus increased while the impact strength remained practically constant at 14 J/m for the filling contents tested. Elastic and flexural moduli increased respectively from 906 MPa to 1.1 GPa and from to 1.26 to 1.81 GPa with corncob addition.

36 MATERIALS SCIENCE↗

Surface treated polypropylene (PP) fibres for reinforced concrete

Surface treatments on a polypropylene (PP) fibre have contributed to the improvement of fibre/concrete adhesion in fibre-reinforced concrete. The treatments to the PP fibre were characterized by contact angle measurements, ATR-IR and XPS to analyse chemical alterations. The surface topography and fibre/concrete interaction were analysed by several microscopic techniques, namely optical petrographic, and scanning electron microscopy. Treatment modified the surface chemistry and topography of the fibre by introducing sodium moieties and created additional fibre surface roughness. Modifications in the fibre surface led to an increase in the adhesion properties between the treated fibres and concrete and an improvement in the mechanical properties of the fibre-reinforced concrete composite as compared to the concrete containing untreated PP fibres. Compatibility with the concrete and increased roughness and mineral surface was also improved by nucleated portlandite and ettringite mineral association anchored on the alkaline PP fibre surface, which is induced during treatment.

36 MATERIALS SCIENCE↗

Optimization of matrix viscosity improves polypropylene fiber dispersion and properties of engineered cementitious composites

Engineered cementitious composites (ECC) is a durable cementitious material with high tensile ductility and strain-hardening characteristics. Although considered as a cost-effective fiber for ECC, polypropylene (PP) fiber is reportedly difficult to disperse in mortar matrix due to its high aspect ratio and hydrophobicity. In this study, the matrix viscosity of a low-carbon ECC based on limestone calcined clay cement was tailored as a variable to improve PP fiber dispersion under a pre-determined mixing protocol. The effect of matrix viscosity on the composite fresh and hardened properties was investigated experimentally. Results suggested an optimal range of matrix viscosity (10.3–11.5 Pa . s) favors the composite tensile strength and strain capacity at 28 days. At the optimal state with a 0.1 % viscosity modifying admixture (VMA)-to-binder mass ratio, PP-ECC achieved 7.0 % tensile strain capacity and 3.5 MPa ultimate tensile strength. When matrix viscosity falls outside the desired range, both ultimate tensile strength and strain capacity were diminished. By tailoring the VMA dosage, the matrix viscosity can be adjusted for desired fiber dispersion, workability, and mechanical properties. Finally, the findings of this study provide a technical reference for the practical design and application of PP-ECC.

36 MATERIALS SCIENCE↗

Comparison of Bolus Materials to Highly Absorbent Polypropylene and Rayon Cloth

This study assesses the utility of a highly absorbent polypropylene and rayon cloth (HAPRC) as a bolus material in radiation therapy. A comparison of various bolus materials used clinically at our center to the test bolus material, water-saturated HAPRC, was conducted. The reproducibility of the physical density was assessed by computerized tomography (CT) scanning the water-saturated HAPRC on a uniform density block phantom on multiple occasions, allowing the cloth to dry fully between subsequent CT scans. The cloth was found to have a consistent physical density between 0.8 and 1.0 g/cm{sup 3}. To evaluate the dosimetric impact of the various bolus materials, metal oxide semiconductor field effect transistor dosimetry measurements were performed for a 6 MV treatment beam on the anterior surface of an anthropomorphic thorax phantom. The ability of the bolus material to conform to an irregular surface was assessed by CT scanning the various bolus materials overlaying the nose of an anthropomorphic head phantom and another irregularly shaped test object. The HAPRC conforms well to irregular contours and is relatively inexpensive compared to Superflab and thermoplastic sheets. Before implementing the material into the clinical setting, an appropriate process for laundering the material should be determined, for hygienic reasons.

61 RADIATION PROTECTION AND DOSIMETRY↗

Effect of fiber sizing and glass fiber laminate hybridization on vibration damping and mechanical properties of banana fiber reinforced polypropylene composites

Modern automotive applications demand lightweight, multifunctional materials to reach mileage goals and natural fiber reinforced composites (NFRCs) are one of the classes of materials proposed as a solution. NFRCs exhibit good vibration damping properties and have low density, but are often limited by processing challenges, poor-fiber matrix compatibility and variable performance. Herein, we investigate non-woven wet-lay of comingled banana fiber (BF), recycled glass fiber (rGF), and polypropylene (PP) fibers to in situ sizing and preparation of composite feedstocks for compression molding. BF and rGF hybrids were prepared by stacking rGF layers during compression molding to produce composites with various fiber ratios. The effect of fiber content, in-situ sizing and ratio of BF to rGF on tensile, flexural and vibration damping performance are investigated. Key results are the significant increase in tensile strength by in situ sizing (40 % sized at 60 wt% BF) and in flexural modulus (+58 % sized at 60 wt% BF) and flexural strength (+41 % sized 60 wt% BF) compared to the unsized equivalent. For BF-rGF hybrid composites with40 wt% total fiber content, flexural strength and modulus were improved by 51 % and 231 % respectively for a 1:1 ratio BF:rGF compared to BF reinforced system. Lastly, identifying the cross-over point where damping and stiffness are optimized for a hybrid composite. These findings demonstrate that these composites can be used as alternative to synthetic fiber or mineral filled composites in automotive applications, particularly where weight reduction, vibration damping and stiffness are desired.

Banana fiber↗

Addition of tracers into the polypropylene in view of automatic sorting of plastic wastes using X-ray fluorescence spectrometry

This study focused on the detection of rare earth oxides, used as tracers for the identification of polymer materials, using XRF (X-ray fluorescence) spectrometry. The tests were carried out in a test system device which allows the collection of static measurements of the samples' spectrum through the use of energy dispersive X-ray fluorescence technology. A sorting process based on tracers added into the polymer matrix is proposed in order to increase sorting selectivity of polypropylene during end-of-life recycling. Tracers consist of systems formed by one or by several substances dispersed into a material, to add a selective property to it, with the aim of improving the efficiency of sorting and high speed identification. Several samples containing rare earth oxides (Y{sub 2}O{sub 3}, CeO{sub 2}, Nd{sub 2}O{sub 3}, Gd{sub 2}O{sub 3}, Dy{sub 2}O{sub 3}, Er{sub 2}O{sub 3} and Yb{sub 2}O{sub 3}) in different concentrations were prepared in order to analyse some of the parameters which can influence the detection, such as the concentration of tracers, the acquisition time and the possible overlapping among the tracers. This work shows that by using the XRF test system device, it was possible to detect 5 of the 7 tracers tested for 1 min exposure time and at a concentration level of 1000 ppm. These two parameters will play an important role in the development of an industrial device, which indicates the necessity of further works that needs to be conducted in order to reduce them.

36 MATERIALS SCIENCE↗

Improved properties of recycled polypropylene by introducing the long chain branched structure through reactive extrusion

Highlights: • A novel approach is applied to modify recycled PP. • Long chain branched structure is introduced onto recycled PP. • The structural change of recycled PP is determined by FTIR, DSC and rheology. • The impact strength of recycled PP is obviously improved. • Inorganic fillers have no effect on the modification of recycled PP. - Abstract: An approach originated from preparing long chain branched polypropylene (PP) was applied to modify the properties of recycled PP that involved reactive extrusion to introduce a branched chain structure onto recycled PP under the assistance of chemical reaction between maleic anhydride (MAH) monomer and glycidyl methacrylate (GMA) grafts. The results from Fourier transformed infrared spectroscopy (FTIR) indicated the reaction took place during melt mixing, and the intensity of ester increased with increasing amount of MAH. Several rheological plots including complex viscosity, storage modulus, loss modulus, loss tangent and Cole-Cole plot were used to investigate the rheological properties of recycled PP and modified PP with MAH, which indicated an additional longer relaxation time that was not shown in recycled PP. The effects of branched structure on melting and crystallization behaviors were also investigated, demonstrating the branched chains acted as nucleating agent. Moreover, the branched structure of modified samples gave rise to enhance mechanical properties, especially, the higher impact strength compared with recycled PP.

36 MATERIALS SCIENCE↗

Size and Structure Effects of Carbon-Supported Ruthenium Nanoparticles on Waste Polypropylene Hydrogenolysis Activity, Selectivity, and Product Microstructure

Hydrogenolysis of plastic waste using Ru-based catalysts is promising for deconstructing polyolefins into lower molecular weight products. Yet, the effect of catalyst atomic structure and size on activity and product selectivity is poorly understood. Herein, we expose the effect of metal particle size and atomic structure on isotactic-polypropylene (i-PP) hydrogenolysis over Ru supported on carbon. Despite similar molecular weight distributions of solid and liquid products, their physical properties are distinct due to different chain regio-irregular CH3 sequences of steric pentads containing racemo configurations. We propose that i-PP hydrogenolysis entails an interplay of C–C bond scission and stereoisomerization. The active site’s local electronic environment and structure dictate the former, whereas polymer–catalyst surface interactions creating suitable polymer conformations control the latter. C–C scission and stereoisomerization are structure-sensitive. Small, disordered nanoclusters are effective in C–C bond scission, whereas larger metal nanoparticles promote stereoisomerization. Finally, we hypothesize that a heterogeneous distribution of metal active sites is essential for deconstruction and product (lubricant base oil) quality control.

36 MATERIALS SCIENCE↗

Spatial Distribution of -Crystals in Metallocene-Made Isotactic Polypropylene Crystallized under Combined Thermal and Flow Fields

The present Article reports the relationships between molecular orientation, formation, and spatial distribution of {gamma}-crystals in metallocene-made isotactic polypropylene (m-iPP) samples prepared by two industrial processes: conventional injection molding (CIM) and oscillatory shear injection molding (OSIM), in which combined thermal and flow fields typically exist. In particular, spatial distributions of crystallinity, fraction of {gamma}-crystal (f{gamma}) with respect to {alpha}-crystal, and lamella-branched shish-kebab structure in the shaped samples were characterized by synchrotron two-dimensional (2D) wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) techniques. The results showed that the crystallinity in any given region of OSIM samples was always higher than that of CIM samples. The value of f{gamma} increased monotonously from skin to core in CIM samples, whereas the corresponding f{gamma} increased nonmonotonically in OSIM samples. The spatial distribution of {gamma}-crystal in OSIM samples can be explained by the epitaxial arrangement between {gamma}- and {alpha}-crystal in a lamella-branched shish-kebab structure. In the proposed model, the parent lamellae of {alpha}-crystal provide secondary nucleation sites for daughter lamellae of {alpha}-crystal and {gamma}-crystal, and the different content of parent lamellae results in varying amounts of {gamma}-crystal. In OSIM samples, the smallest parent-daughter ratio ([R] = 1.38) in the core region led to the lowest fraction of {gamma}-crystal (0.57), but relatively higher {gamma}-crystal content (0.69) at 600 and 1200 {micro}m depth of the samples (corresponding to [R] of 4.5 and 5.8, respectively). This is consistent with the proposed model where more parent lamellae provide more nucleation sites for crystallization, thus resulting in higher content of {gamma}-crystal. The melting behavior of CIM and OSIM samples was studied by differential scanning calorimetery (DSC). The observed double-melting peaks could be explained by the melting of {gamma}- and {alpha}-crystal of the shaped samples. The f{gamma} distribution calculated from the relative areas of the peaks in the DSC scans was also consistent with the WAXD results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Suppressing the Skin-Core Structure of Injection-Molded Isotactic Polypropylene via Combination of an in situ Microfibrillar Network and an Interfacial Compatibilizer

Injection-molded semicrystalline polymer parts generally exhibited a so-called skin-core structure basically as a result of the large gradients of temperature, shear rate, stress, and pressure fields created by the boundary conditions of injection molding. Suppression of the skin-core structure is a long-term practical challenge. In the current work, the skin-core structure of the conventional injection-molded isotactic polypropylene (iPP) was largely relieved by the cooperative effects of an in situ microfibrillar network and interfacial compatibilizer. The in situ poly(ethylene terephthalate) microfibrils of 1-8 {micro}m in diameter and large aspect ratios of above 40 tended to entangle with each other to generate a microfibrillar network in the iPP melt. During injection molding, the iPP molecules experienced confined flow in the microchannels or pores formed by the microfibrillar network, which could redistribute and homogenize the flow field of polymer melt. Addition of the compatibilizer, glycidyl methacrylate-grafted iPP, restrained the molecular orientation but facilitated preservation of oriented molecules due to the chemical bonds at the interface between PET microfibrils and iPP. The cooperative effects of in situ microfibrillar network and interfacial compatibilizer led to almost the same molecular orientation across the whole thickness of the injection-molded parts. Additionally, the content of {beta} crystals in different layers of injection-molded iPP parts depended on the combined effects of the molecular orientation, the amount of oriented crystals, and the crystallization time between 105 and 140 C. The presence of the interfacial compatibilizer facilitated formation of the {beta} crystals because of preservation of the oriented molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Competitive Growth of - -Crystals in -Nucleated Isotactic Polypropylene under Shear Flow

It has been well established that, although both shear flow and {beta}-nucleating agent could separately induce {beta}-crystals in isotactic polypropylene (iPP) in an efficient manner, their combination in fact depressed the content of {beta}-crystals when compared with quiescently crystallized {beta}-nucleated iPP. In the current study, in-situ synchrotron wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) measurements were performed to investigate this behavior. The WAXD data obtained were quantitatively analyzed to determine the independent contributions of applied shear flow and added {beta}-nucleating agent in terms of nucleation stage and subsequent {alpha}- and {beta}-crystal growth stage. In the nucleation stage, the addition of {beta}-nucleating agent increased the amount of {beta}-nuclei, while the application of shear flow and the interactions between shear and {beta}-nucleating agent enhanced the amount of {alpha}-nuclei (the amounts of {alpha}- and {beta}-nuclei were in the same order of magnitude). As a result, in the initial crystallization, {alpha}- and {beta}-crystals grew competitively, causing simultaneously increments of {alpha}- and {beta}-crystals. However, in the growth stage, the growth rate of {beta}-crystals was faster than that of {alpha}-crystals where the epitaxial growth of {beta}-crystals on {alpha}-crystals also occurred (due to more favorable isothermal crystallization temperature for {beta}-crystal growth). Consequently, the content of {beta}-crystals became dominant in the limited growth space; however, it was still less than that formed from the quiescent isothermal crystallization of {beta}-nucleated iPP. As the shear rate increased, more shear-induced {alpha}-nuclei were formed, further decreasing the amount of {beta}-crystals. Nevertheless, when shear and {beta}-nucleating agent coexisted, {beta}-crystals emerged earlier than {alpha}-crystals. The SAXS results indicated that the combination of shear and {beta}-nucleating agent changed the stacking manner of molecular chains, so that the long period of sheared, {beta}-nucleated iPP was comparable to that of quiescently crystallized iPP.

36 MATERIALS SCIENCE↗

Graphene Nanosheets and Shear Flow Induced Crystallization in Isotactic Polypropylene Nanocomposites

Combined effects of graphene nanosheets (GNSs) and shear flow on the crystallization behavior of isotactic polypropylene (iPP) were investigated by in-situ synchrotron wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) techniques. For crystallization under quiescent condition (at 145 C), the half-crystallization time (t{sub 1/2}) of nanocomposites containing 0.05 and 0.1 wt % GNSs was reduced to at least 50% compared to that of neat iPP, indicating the high nucleation ability of GNSs. The crystallization rate of iPP was directly proportional to the GNS content. Under a relatively weak shear flow (at a rate of 20 s{sup -1} for 5 s duration) and a low degree of supercooling, the neat iPP exhibited an isotropic structure due to the relaxation of row nuclei. However, visible antisotropic crystals appeared in sheared iPP/GNSs nanocomposites, indicating that GNSs induced a network structure hindering the mobility of iPP chains and allowing the survival of oriented row nuclei for a long period of time. The presence of GNSs clearly enhanced the effects of shear-induced nucleation as well as orientation of iPP crystals. Two kinds of nucleating origins coexisted in the sheared nanocomposite melt: heterogeneous nucleating sites initiated by GNSs and homogeneous nucleating sites (row nuclei) induced by shear. The difference of t{sub 1/2} of nanocomposites with and without shear was significantly larger than that of neat iPP. The presence of GNSs and shear flow exhibited a synergistic interaction on promoting crystallization kinetics of iPP, although the effect of GNS concentration was not apparent. From WAXD results of isothermal and nonisothermal crystallization of sheared iPP, it was found that the appearance of {beta}-crystals depended on the preservation of row nuclei, where the {alpha}-crystals were predominant in the iPP/GNSs nanocomposites, indicating that GNSs could directly induce {alpha}-crystals of iPP.

36 MATERIALS SCIENCE↗