Results for “powertrain simulation” — Page 3

NASA NTRSDate not supplied

Control and Scaling Approach for the Emulation of Dynamic Subscale Torque Loads

Research and development of electrified aircraft propulsion powertrains is moving toward the use electro-mechanical systems to emulate the loads a system imparts on another. Replacing a prime mover with a model driving an electro-mechanical system capable of emulating loads that regulate the system to produce a desired response is a lower risk, lower cost alternative to using the traditional prime mover for control system verification. This paper outlines a control and scaling approach for emulating scaled dynamic torque loads using electric machine (EM) hardware for electrified aircraft propulsion research and development purposes. The approach, known as the Sliding Mode Impedance Controller with Scaling (SMICS), drives a mechanically coupled two-EM system that provides a scaled hardware representation of an electrified turbomachinery shaft. One EM reflects inertial dynamics and load of the shaft under steady-state and transient operation while the second EM represents a motor/generator connected to the shaft. This closed loop system applies impedance and sliding mode control schemes to match desired dynamics in real-time along with parameter scaling to effectively scale full scale torque inputs, a full-scale desired inertia, and sub-scale speed feedback. The result is a sub-scale hardware implementation of a coupled EM system that is command-able by a model and control system designed for a full-scale electrified aircraft propulsion powertrain. The paper elaborates on the need for closed loop control and scaling as well as impedance and sliding mode control theory, shows a derivation of the controller and scaling, its implementation, and presents a comparison of theoretical and actual simulation results acquired during hardware-in-the-loop testing of a partial turboelectric propulsion concept at the NASA Electric Aircraft Testbed (NEAT).

Santino J Bianco↗

NASA NTRSDate not supplied

Failure Behavior and Control-Based Mitigation for a Parallel Hybrid Propulsion System

NASA is pursuing research to advance Electrified Aircraft Propulsion (EAP) technologies that address fuel burn and emission reduction goals. EAP brings the potential for improved performance over the state of the art. However, for these systems to be practical and certifiable, they need to possess adequate robustness to adverse conditions including a variety of system failures that are not applicable to conventional turbofans today. Numerous EAP concepts interface gas turbine engines with an electrical power system that includes electric machines and sometimes electrical energy storage. The expansion of the powertrain increases the probability of encountering a failure and introduces new failure modes. Failures within the electrical power system may also impact the gas turbine engine(s) to which the electrical powertrain is coupled. This effort investigates failures originating in the electrical power system and their impact on the parallel hybrid propulsion system. Reversionary control strategies are also demonstrated to reduce the impact of the failures. Failure mitigation strategies were devised and employed in simulation. Various failure scenarios were simulated including those occurring during steady state operation, transients, and takeoff and landing scenarios. The timing of the failure and delay in failure identification and activation of mitigation strategies are noteworthy variables in the study. While the system remained stable throughout all failure scenarios, delays in failure identification could result in undesirable conditions such as increased operating temperatures and reduced stall margin. The results demonstrate successful mitigation of failures through reversionary control modes and help to generate confidence in the robustness of the conceptual parallel hybrid propulsion system.

Failure behavior↗

NASA NTRSDate not supplied

Failure Behavior and Control Based Mitigation for a Parallel Hybrid Propulsion System

NASA is pursuing research to advance Electrified Aircraft Propulsion (EAP) technologies that address fuel burn and emission reduction goals. EAP brings the potential for improved performance over the state of the art. However, for these systems to be practical and certifiable, they need to possess adequate robustness to adverse conditions including a variety of system failures that are not applicable to conventional turbofans today. Numerous EAP concepts interface gas turbine engines with an electrical power system that includes electric machines and sometimes electrical energy storage. The expansion of the powertrain increases the probability of encountering a failure and introduces new failure modes. Failures within the electrical power system may also impact the gas turbine engine(s) to which the electrical powertrain is coupled. This effort investigates failures originating in the electrical power system and their impact on the parallel hybrid propulsion system. Reversionary control strategies are also demonstrated to reduce the impact of the failures. Failure mitigation strategies were devised and employed in simulation. Various failure scenarios were simulated including those occurring during steady state operation, transients, and takeoff and landing scenarios. The timing of the failure and delay in failure identification and activation of mitigation strategies are noteworthy variables in the study. While the system remained stable throughout all failure scenarios, delays in failure identification could result in undesirable conditions such as increased operating temperatures and reduced stall margin. The results demonstrate successful mitigation of failures through reversionary control modes and help to generate confidence in the robustness of the conceptual parallel hybrid propulsion system.

Failure behavior↗

NASA NTRSDate not supplied

Advanced Turboprop Transport Aircraft Modeling for the Electrified Powertrain Flight Demonstration Project

The objective of this study is to establish models for state of the art, representative regional non-electrified turboprop configurations in the 19 to 50 passenger capability range and assess performance impacts from advanced aircraft technologies. Two of these models will serve as reference baseline configurations for comparison to electrified aircraft propulsion (EAP) demonstrator concepts for the Electrified Powertrain Flight Demonstration (EPFD) project. The other two non-electrified configurations will primarily assess the impacts of advanced technologies on fuel consumption and CO₂ emissions. This paper details an aircraft synthesis and performance analysis approach using the General Aviation Synthesis Program (GASP) which is used to establish baseline performance capabilities, calibrate airplane and engine models using published manufacturer data and conduct technology sensitivity studies. Advanced technologies are selected from the categories of propulsion, aerodynamics, and flight systems. A GASP-Monte Carlo simulation framework for uncertainty propagation is used to obtain performance distributions of the expected fuel burn, weight reduction and CO₂ emissions reductions from advanced aircraft technologies. Significant fuel burn savings from application of aerodynamics and propulsion technologies was observed.

Dahlia D.V. Pham↗

NASA NTRSDate not supplied

SUbsonic Single Aft eNgine (SUSAN) Power/Propulsion System Hardware-in-the-Loop Test Results

Electrified Aircraft Propulsion (EAP) technology offers a promising path forward for reducing greenhouse gas emissions and other negative environmental effects from the commercial aviation sector. EAP systems can reduce fuel burn and improve performance over state-of the-art designs, however the increased complexity and highly coupled nature of these systems present challenges that require new control approaches. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a concept aircraft developed by NASA as a reference design for a commercial transport aircraft with a highly integrated hybrid-electric powertrain. This paper summarizes the results of a Hardware-in-the-Loop (HIL) test of a control architecture developed for the SUSAN power/propulsion system (PPS). The test was performed in the Hybrid Propulsion Emulation Rig (HyPER) facility at the NASA Glenn Research Center (GRC) and involved a real-time reference model of the SUSAN PPS and control system running with a sub-scale electro-mechanical system replacing one of the PPS subsystems. A side-by-side comparison of the simulated and real systems in the HIL test results shows that the control architecture functions well in both the simulation and the real-time HIL environment. In both cases the controller is able to simultaneously deliver the required thrust response and balance power levels between the electrical and turbomachinery subsystems.

Jonah J Sachs-Wetstone↗

NASA NTRSDate not supplied

SUbsonic Single Aft eNgine (SUSAN) Power/Propulsion System Hardware-in-the-Loop Test Results

Electrified Aircraft Propulsion (EAP) technology offers a promising path forward for reducing greenhouse gas emissions and other negative environmental effects from the commercial aviation sector. EAP systems can reduce fuel burn and improve performance over state-of the-art designs, however the increased complexity and highly coupled nature of these systems present challenges that require new control approaches. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a concept aircraft developed by NASA as a reference design for a commercial transport aircraft with a highly integrated hybrid-electric powertrain. This paper summarizes the results of a Hardware-in-the-Loop (HIL) test of a control architecture developed for the SUSAN power/propulsion system (PPS). The test was performed in the Hybrid Propulsion Emulation Rig (HyPER) facility at the NASA Glenn Research Center (GRC) and involved a real-time reference model of the SUSAN PPS and control system running with a sub-scale electro-mechanical system replacing one of the PPS subsystems. A side-by-side comparison of the simulated and real systems in the HIL test results shows that the control architecture functions well in both the simulation and the real-time HIL environment. In both cases the controller is able to simultaneously deliver the required thrust response and balance power levels between the electrical and turbomachinery subsystems.

EAP↗

NASA NTRSDate not supplied

Advanced Turboprop Transport Aircraft Modeling for the Electrified Powertrain Flight Demonstration Project

The objective of this study is to establish models for state of the art, representative regional non-electrified turboprop configurations in the 19-50 passenger capability range and assess performance impacts from advanced aircraft technologies. Two of these models will serve as reference baseline configurations for comparison to electrified aircraft propulsion (EAP) demonstrator concepts for the Electrified Powertrain Flight Demonstration (EPFD) project. The other two non-electrified configurations will primarily assess the impacts of advanced technologies on fuel consumption and CO₂ emissions. This paper details an aircraft synthesis and performance analysis approach using the General Aviation Synthesis Program (GASP) which is used to establish baseline performance capabilities, calibrate airplane and engine models using published manufacturer data and conduct technology sensitivity studies. Advanced technologies are selected from the categories of propulsion, aerodynamics, and flight systems. Performance assessments use Monte Carlo method coupled with GASP simulations to obtain performance distributions of the expected fuel burn, propulsive, aerodynamic, and weight benefits on the representative turboprop configurations from the application of advanced technologies. The final paper will present the impact of the advanced technologies on fuel burn and CO₂ emissions.

aircraft performance↗

NASA NTRSDate not supplied

Hybrid Electric Aircraft with Unlike Engine Degradation

Control solutions are applied to uneven engine performance degradation on a conceptual twin-engine transport-class aircraft. Such degradation can lead to asymmetric thrust, which requires rudder trim to maintain desired aircraft heading. This will increase drag and fuel consumption. With the introduction of hybrid-electric aircraft powertrains, new solutions to unwanted asymmetric thrust can be derived. Four control strategies are demonstrated on the power and propulsion system of such an aircraft. Compared with existing strategies, the methodology proposed in this paper controls electromechanical actuators coupled to engine shafts and balances the thrust produced by both engines potentially leading to a decrease in fuel burn. The engine represented in this study is NASA’s conceptual dual-shaft Advanced Geared Turbofan 30,000 lbf thrust class engine. The conceptual engine is hybridized with electric machines attached to both shafts. Simulation results are presented with various levels of degradation. The control strategies are compared based on fuel burn, thrust symmetry, and estimated system weight.

control↗

NASA NTRSDate not supplied

Hybrid Electric Aircraft with Unlike Engine Degradation

Control solutions are applied to uneven engine performance degradation on a conceptual twin-engine transport-class aircraft. Such degradation can lead to asymmetric thrust, which requires rudder trim to maintain desired aircraft heading. This will increase drag and fuel consumption. With the introduction of hybrid-electric aircraft powertrains, new solutions to unwanted asymmetric thrust can be derived. Four control strategies are demonstrated on the power and propulsion system of such an aircraft. Compared with existing strategies, the methodology proposed in this paper controls electromechanical actuators coupled to engine shafts and balances the thrust produced by both engines potentially leading to a decrease in fuel burn. The engine represented in this study is NASA’s conceptual dual-shaft Advanced Geared Turbofan 30,000 lbf thrust class engine. The conceptual engine is hybridized with electric machines attached to both shafts. Simulation results are presented with various levels of degradation. The control strategies are compared based on fuel burn, thrust symmetry, and estimated system weight.

control↗

NASA NTRSDate not supplied

Analysis and Optimization of Baseline Single Aisle Aircraft for Future Electrified Powertrain Flight Demonstrator Comparisons

The purpose of this study is to provide baseline single-aisle vehicles for future comparisons with NASA’s Electrified Powertrain Flight Demonstration (EPFD) turbofan-powered Vision Systems. State-of-the-art single-aisle transports with varying design capacities of 100 to 150 passengers are modeled using NASA Ames Research Center’s General Aviation Synthesis Program (GASP) as well as GASPy. GASPy is a modernized Python-based version of GASP built on the OpenMDAO framework to allow for future, efficient gradient-based optimization and coupled airframe-propulsion design. In order to meet projected NASA Aeronautics goals for 2035, advanced aircraft technologies must be incorporated into these vehicle systems. Methodology to parametrically infuse baseline aircraft models with advanced technologies simulating improvements in aerodynamics, structures, and propulsion systems is detailed, along with the results of technology sensitivity studies. Comparison of the baseline and advanced configurations will allow for future analysis of the benefits of future hybrid and fully electric aircraft concepts in the EPFD project, where fuel consumption and emissions will be modeled and assessed. This study has been conducted under the EPFD project to establish benchmark turbofan models and demonstrate System Analysis capabilities in multi-disciplinary aircraft design, analysis, and optimization for advanced turbofan concepts.

Carl J. Recine↗

NASA NTRS2023

Control and Scaling Approach for the Emulation of Dynamic Subscale Torque Loads

Research and development of electrified aircraft propulsion powertrains are relying on the use of electromechanical systems to emulate turbomachinery/rotor loads. Replacing a physical turbomachinery/rotor with a model driving a subscale electromechanical system capable of emulating subscale torque loads and responses is a lower risk, lower cost alternative to using the full-scale turbomachinery/rotor for initial control system verification. This paper outlines a novel control and scaling approach for emulating dynamic subscale torque loads using electric machine (EM) hardware for electrified aircraft propulsion research and development purposes. The approach, known as the Sliding Mode Impedance Controller with Scaling (SMICS), drives a mechanically coupled, two-EM system to behave like a subscale hardware representation of a hybrid-electric turbomachinery shaft. One EM reflects the inertial dynamics and torque load of the subscale turbomachinery under steady-state and transient operation while the second EM represents a motor/generator connected to the shaft, which is intended to hybridize the turbomachinery. This closed loop control and scaling algorithm applies impedance and sliding mode control schemes, along with parameter scaling, to match subscale, desired dynamics in real-time and to allow this system to be driven by a full-scale hybrid-electric turbomachinery model and control. The paper elaborates on the concept of the closed loop control and scaling approach and explains the significance of using impedance and sliding mode control. It shows a derivation of the closed loop control and scaling algorithm, its implementation, and presents a comparison of theoretical and actual simulation results acquired during hardware-in-the-loop testing of a partial turboelectric propulsion concept aircraft at the NASA Electric Aircraft Testbed (NEAT).The results show that the intended dynamic responses of the hardware and the aircraft model are achieved in both the time and frequency domain. Full scale propulsion control systems can be tested using this hardware and software approach.

Emulation↗