Search NASA⌕ Search

SEARCH · Search NASA

Results for “preferential diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Extensive nanoprecipitate morphology transformation in a nanostructured ferritic alloy due to extreme thermomechanical processing

Nano-oxide precipitates in a modern nanostructured ferritic alloy were investigated after extreme thermomechanical processing into a thin-walled tube geometry. It was found that the morphology of the precipitates changed from spherical to rod-shaped, with some increasing to aspect ratios of up to 9, despite the precipitate volume fraction (0.3%) and number density (> 10 23 m -3 ) of precipitates remaining unchanged. High-resolution electron microscopy showed that the precipitates likely remained coherent with the Fe-matrix, while atom probe tomography confirmed that the precipitate compositions remained unaffected by the transformation. The morphological change was attributed to the shearable nature of the (Y,Ti,O)-rich precipitates, indicating they should be considered as “soft” obstacles to dislocation motion. The elongation was most pronounced in larger (>5 nm) precipitates, which may be caused by preferential dissolution of the smallest (1–3 nm) precipitates followed by the competition between re-precipitation and solute diffusion to larger precipitates during recovery heat treatments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Dynamics and structure of the B2→B19’ phase transformation in NiTi revealed through in situ 4D-STEM

The structural evolution of NiTi during the B2→B19’ martensitic phase transformation via thermal cycling is investigated using in situ four dimensional scanning transmission electron microscopy (4D-STEM). With 4D-STEM, we can directly visualize and quantify the nanoscale evolution of the martensitic structure on thermal cycling and also investigate the origin of diffuse scattering of NiTi in the pre-transitional state. Mapping of the martensite orientation and strain visualizes the progression of the transformation front and self-accommodation of the B19’ structure. Diffuse streaking and strain are measured in the pre-transitional austenite (B2) phase and demonstrate no localization or preferential directionality hinting that long-range homogeneous instability rather than nanoscale heterogeneities may be the origin of the pre-transitional anomalies in NiTi. Finally, it is revealed that NiTi does not reform the same martensite nanostructure on thermal cycling but does express similar features. This small variation is likely owing to transformation-induced dislocations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Relationship between microporous structure and light gas transport through glassy polymeric membranes revealed by molecular simulations

Microporous glassy polymers are attractive materials for gas separation membranes, due to their high permeability and tailorable selectivity, provided physical aging can be delayed. The archetypal microporous glassy polymer, PTMSP, can be blended with a hyper-crosslinked isatin–triptycene porous polymer network (PPN) to delay physical aging. However, while PPN is effective at reducing physical aging, it also affects the permeability of light gases through PTMSP. Molecular dynamics simulations were used here to shed fundamental light on the mechanisms responsible for these effects. Atomistic models are developed that satisfactorily reproduce experimental observations such as matrix density and cavity size distributions for neat PTMSP as well as for PTMSP–PPN blends. Analysis of the simulation results suggests that physical aging is delayed because the PPN inclusions slow down PTMSP relaxation while reducing the connectivity between free volume pockets. To understand how PPN inclusions affect light gas permeability, the atomistic models developed are used to probe CO 2 and CH 4 diffusion and sorption. These simulations are conducted for PTMSP matrices exhibiting varying density, towards reproducing experimental permeability data. Interrogating the simulation trajectories, it is discovered that while CH 4 travels preferentially through the free volume cavities, CO 2 preferentially interacts with the available surfaces, especially in the presence of PPN. These differences help interpret experimental observations. The transport of C 2 H 6 and H 2 S through PTMSP matrices was also investigated. These gases, and in particular H 2 S, were found to absorb within PTMSP, yielding very low diffusion coefficients. The ability to predict differences in diffusion pathways for various natural gas components unveils the possibility of engineering membranes to control permeability and selectivity towards large-scale applications.

Bao Le, Tran Thi [Univ. of Oklahoma, Norman, OK (U↗
DOE OSTI2023

Surface premelting of ice far below the triple point

Premelting of ice, a quasi-liquid layer (QLL) at the surface below the melting temperature, was first postulated by Michael Faraday 160 y ago. Since then, it has been extensively studied theoretically and experimentally through many techniques. Existing work has been performed predominantly on hexagonal ice, at conditions close to the triple point. Whether the same phenomenon can persist at much lower pressure and temperature, where stacking disordered ice sublimates directly into water vapor, remains unclear. Herein, we report direct observations of surface premelting on ice nanocrystals below the sublimation temperature using transmission electron microscopy (TEM). Similar to what has been reported on hexagonal ice, a QLL is found at the solid-vapor interface. It preferentially decorates certain facets, and its thickness increases as the phase transition temperature is approached. In situ TEM reveals strong diffusion of the QLL, while electron energy loss spectroscopy confirms its amorphous nature. More significantly, the premelting observed in this work is thought to be related to the metastable low-density ultraviscous water, instead of ambient liquid water as in the case of hexagonal ice. This opens a route to understand premelting and grassy liquid state, far away from the normal water triple point.

58 GEOSCIENCES↗
DOE OSTI2022

Perspective: Biochemical and Physical Constraints Associated With Preparing Thin Specimens for Single-Particle Cryo-EM

While many aspects of single-particle electron cryo-microscopy (cryo-EM) of biological macromolecules have reached a sophisticated level of development, this is not yet the case when it comes to preparing thin samples on specimen grids. As a result, there currently is considerable interest in achieving better control of both the sample thickness and the amount of area that is useful, but this is only one aspect in which improvement is needed. This Perspective addresses the further need to prevent the macromolecular particles from making contact with the air-water interface, something that can result in preferential orientation and even structural disruption of macromolecular particles. This unwanted contact can occur either as the result of free diffusion of particles during the interval between application, thinning and vitrification of the remaining buffer, or—when particles have been immobilized—by the film of buffer becoming too thin prior to vitrification. An opportunity now exists to apply theoretical and practical insights from the fields of thin-film physical chemistry and interfacial science, in an effort to bring cryo-EM sample preparation to a level of sophistication that is comparable to that of current data collection and analysis.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Revealing in-plane movement of platinum in polymer electrolyte fuel cells after heavy-duty vehicle lifetime

Fuel cell heavy-duty vehicles (HDVs) require increased durability of oxygen-reduction-reaction electrocatalysts, making knowledge of realistic degradation mechanisms critical. Here identical-location micro-X-ray fluorescence spectroscopy was performed on membrane electrode assemblies. The results exposed heavy in-plane movement of electrocatalyst after HDV lifetime, suggesting that electrochemical Ostwald ripening may not be a local effect. Development of local loading hotspots and preferential movement of electrocatalyst away from cathode catalyst layer cracks was observed. The heterogeneous degradation exhibited by a modified cathode gas diffusion layer membrane electrode assembly after HDV lifetime was successfully quantified by the identical-location approach. Further synchrotron micro-X-ray diffraction and micro-X-ray fluorescence experiments were performed to obtain the currently unknown correlation between electrocatalyst nanoparticle size increase and loading change. A direct correlation was discovered which developed only after HDV lifetime. Finally, the work provides a route to engineer immediate system-level mitigation strategies and to develop structured cathode catalyst layers with durable electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Selenium Migration and Local Structures in Cu‐Doped CdSeTe Solar Cells after Aging

Selenium grading plays a critical role in state-of-the-art Cadmium Telluride photovoltaic cells by enhancing long-wavelength absorption and extending minority carrier lifetimes —key to enabling the current performance record of 23.08%. However, very little is understood about selenium motion. In this study, a comprehensive, multimodal, and multiscale approach is employed to investigate Se migration and local structural changes in copper (Cu)-doped CdSeTe solar cells subjected to accelerated stress. X-ray fluorescence (XRF) microscopy shows unexpected levels of Se diffusion after 500 h under heat (75°C) and light (0.8 suns, 80 mW/cm 2 ), suggesting the coexistence of fast and slow diffusion channels even at low temperatures, with unexpectedly low activation energies (<0.85 eV). X-ray Absorption Near Edge Structure (XANES) analysis indicates a preferential migration of Se atoms to anionic lattice sites and a reduction in Se-Cl co-passivation at Te-terminated dislocation cores. Furthermore, these findings point to a reconfiguration of Se local environments and highlight the potential role of extended structural defects in enabling Se transport at low temperatures. Additionally, XANES results suggest that the presence of metallic Cu across the absorber layer may contribute to back-contact degradation and reduced hole density in both fresh and aged devices.

14 SOLAR ENERGY↗
DOE OSTI2025

Influence of Ether-Functionalized Pyrrolidinium Ionic Liquids on Properties and Li + Cation Solvation in Solvate Ionic Liquids

Ionic liquids are tunable solvents composed entirely of ions that have properties desirable as electrolytes for lithium batteries such as non-flammability and a large electrochemical stability window. Solvate ionic liquids are a subclass of ionic liquids that consist of a glyme-based solvent and lithium salt in an equimolar ratio, where Li + cation-glyme solvation interactions result in ionic liquid-like properties. LiG4TFSi is a well-studied solvate ionic liquid consisting of equimolar amounts of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and tetraglyme (G4). In this work, pyrrolidinium ionic liquids with ether-functionalized side chains were synthesized containing either one ether (EO1) moiety or three ether (EO3) moieties and mixed with LiG4TFSI to form a new class of electrolyte mixtures. Their physical and transport properties, as well as ion solvation structures, were characterized by electrochemical, thermal, rheological, and spectroscopic measurements. The conductivity of the electrolyte mixture composed of EO1:LiTFSI:G4 in a 1:1:1 molar ratio is 2.54 mS/cm at 30 °C, compared to 1.53 mS/cm for LiG4TFSI, an increase of 67%. A significant decrease in the conductivity to 0.279 mS/cm is observed for the EO3:LiTFSI:G4 mixture in a 1:1:0.4 molar ratio. Pulsed-field gradient nuclear magnetic resonance (PFG-NMR) measurements revealed that the EO1 cation diffuses significantly faster than the EO3 cation in their respective mixtures. Liquid-state 13 C NMR experiments indicate that Li + cations preferentially coordinate with tetraglyme. Li + cations do not coordinate with the EO1 cation and only coordinate with EO3 ether side chains at lower concentrations of tetraglyme. We hypothesize that the oligoether EO3 cation competes with G4 and TFSI - for lithium cation solvation in G4 deficient compositions, leading to a largely adverse effect on the mass transport properties of the electrolyte.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Impact of metal diffusion, lattice distortions, native defects, and ambient on dielectric breakdown in Ni–Ga 2 O 3 Schottky diodes

Ga 2 O 3 unipolar devices are of high interest due to their ~8 MV/cm predicted breakdown fields, which have not yet been achieved due to premature device failure. Pre- and post-failure defect analysis of Ni–Ga 2 O 3 Schottky diodes in ultrahigh vacuum (UHV) and air were performed using depth-resolved cathodoluminescence, high angle annular dark field scanning transmission electron microscopy, and energy dispersive x-ray analysis to understand the physical mechanisms that precede premature breakdown. The breakdown voltage in UHV was dramatically reduced by nearly 40% compared with the breakdown in air. This reduction in the breakdown voltage correlated with post-breakdown differences in Ni distribution, indicating that the coordination and bonding of Ni contribute strongly to electrical behavior in Ni–Ga 2 O 3 Schottky diodes. Breakdown studies in UHV revealed that Ni diffuses away more from the metal–semiconductor interface than with air breakdown, where Ni localizes more near the interface, indicative of the preferential formation of a Ni oxide under O-poor conditions. These measurements also identified the formation of divacancy-interstitial complexes and their characteristic luminescence signature ~150 nm from the interface, the densities of which correlated with breakdown fields. These findings show that electric-field-induced degradation occurs via the rearrangement of native point defects, which act as an additional precursor to device failure. Macroscopically, they show the impact of both vacuum conditions and metal reactivity on Ga 2 O 3 device fabrication.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Complex defect chemistry of hydrothermally-synthesized Nb-substituted β$'$-LiVOPO 4

Lithium vanadyl phosphate (LiVOPO 4 ) is a next-generation multielectron battery cathode that can intercalate up to two Li-ions per V-ion through the redox couples of V 4+ /V 3+ and V 5+ /V 4+ . However, its rate capacity is undermined by the sluggish Li-ion diffusion in the high-voltage region (4 V for V 5+ /V 4+ redox). Nb substitution was used to expand the crystal lattice to facilitate Li-ion diffusion. Here, in this work, Nb substitution was achieved via hydrothermal synthesis, which resulted in a new, lower symmetry β'-LiVOPO 4 phase with preferential Nb occupation of one of the two V sites. This phase presents complex defect chemistries, including cation vacancies and hydrogen interstitials, characterized by a combination of X-ray and neutron diffraction, elemental and thermogravimetric analyses, X-ray absorption spectroscopy, and magnetic susceptibility measurements. The Nb-substituted samples demonstrated improved capacity retention and rate capabilities in the high-voltage region, albeit an enlarged voltage hysteresis related to a partial V 4+ /V 3+ redox reaction, as evidenced by ex situ X-ray absorption spectroscopy and pair distribution function analysis. This work highlights the importance of understanding the complex defect chemistry and its consequence on electrochemistry in polyanionic intercalation compounds.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Chromium segregation-induced oxide evolution in Ni-10Cr alloys during high-temperature oxidation

The oxidation behavior of a Ni-10(wt%)Cr alloy under high-temperature O 2 conditions is investigated using transmission electron microscopy and first-principles calculations. Results reveal that chromium segregation plays a central role in driving the evolution of complex oxide phase structures during oxidation. At low Cr concentrations, Cr preferentially segregates to NiO grain boundaries or internal pores, substituting for Ni atoms and forming Ni(Cr)O solid solutions. As Cr content increases, enhanced diffusion promotes Cr penetration into the NiO lattice, leading to the formation of multiphase oxide structures. First-principles modeling corroborates these findings: at low Cr concentrations, Cr atoms favor surface and grain-boundary segregation, while higher concentrations lead to Cr aggregation within the NiO bulk. Furthermore, the integrated experimental-theoretical approach provides atomistic insights into Cr-mediated mass transport mechanisms during alloy oxidation and offers valuable guidance for controlling oxide growth kinetics and phase stability in Ni-Cr alloys, with implications for improving oxidation resistance in high-temperature structural applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Growth and structural transitions of core-shell nanorods in nanocrystalline Al-Ni-Y

Unique nanorod precipitates with a core-shell structure are found to nucleate from the grain boundaries of a bulk nanocrystalline Al-Ni-Y alloy fabricated via powder consolidation, contributing significantly to stabilization and strengthening. The local structure, chemistry, and evolution of these features during annealing are reported here. In the as-consolidated state, the nanorods can be either structurally ordered or disordered, yet a consistent chemical patterning is found where the core is primarily Al plus C while the shell is enriched with Y. As annealing time increases, more nanorods transform to an ordered structure as they coarsen while the core composition remains unchanged. In contrast, the shell chemistry transitions from Y-rich to Ni-rich with longer annealing treatments, most likely due to the different diffusivities of Y and Ni in Al. Furthermore, a spatial and chemical correlation between the nanorods and amorphous complexions is observed, suggesting that these complexions serve as preferential nucleation sites.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Ab Initio Modeling of Aqueous Methanol Mixtures at DFT-SCAN Level Using Machine Learning Interatomic Potentials

Abstract Methanol–water mixtures find use in many applications, particularly catalytic energy conversion processes. Their importance has motivated numerous computational studies, most of which employed molecular dynamics based on classical force fields. These enable simulations of large systems on long time scales but do not reliably describe reactive dynamics involving bond breaking and bond formation. In contrast, ab initio molecular dynamics (AIMD) based on density functional theory (DFT) is generally more reliable for such applications but has a high computational cost, which discourages systematic studies of alcohol-water mixtures. To remedy this, we trained a machine learning interatomic potential capable of probing the properties of aqueous methanol mixtures at the DFT level using the SCAN functional. Our results show that SCAN qualitatively reproduces multiple key experimental features arising from the amphiphilic nature of methanol, including density, diffusion coefficients, X-ray structure factors, and Kirkwood–Buff integrals. We also find that structural correlations between water molecules are somewhat overestimated, leading to a stronger preferential association than that predicted by experiments. However, increasing the temperature by 30 K mitigates this effect and also recovers the correct mobilities of both methanol and water. These results indicate that SCAN provides an accurate description of methanol–water mixtures, making it a reliable choice for investigating the reactive dynamics in such systems.

Park, Sanghyun J. [Princeton University , , , ,]↗
DOE OSTI2022

Highly stable preferential carbon monoxide oxidation by dinuclear heterogeneous catalysts

Atomically dispersed catalysts have been shown highly active for preferential oxidation of carbon monoxide in the presence of excess hydrogen (PROX). However, their stability has been less than ideal. We show here that the introduction of a structural component to minimize diffusion of the active metal center can greatly improve the stability without compromising the activity. Using an Ir dinuclear heterogeneous catalyst (DHC) as a study platform, we identify two types of oxygen species, interfacial and bridge, that work in concert to enable both activity and stability. In conclusion, the work sheds important light on the synergistic effect between the active metal center and the supporting substrate and may find broad applications for the use of atomically dispersed catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Equilibrium Separation of Siloxanes in Metal–Organic Frameworks

We present an in silico assessment of metal–organic frameworks (MOFs) for the equilibrium separation of linear and cyclic siloxanes. Using a combination of configurational bias/continuous fractional component Monte Carlo (CB/CFCMC) simulations and Ideal Adsorbed Solution Theory (IAST), we investigated the adsorption of both equimolar and nonequimolar mixtures of linear and cyclic siloxanes in a selection of synthesizable MOFs with medium to large pore volumes. We showed that configurational entropy effects drive the preferential adsorption of linear siloxanes over cyclic siloxanes. Based on synthesizability metrics we identified ZIF-70 as a promising adsorbent for the separation of linear and cyclic siloxanes. Self-diffusivities of linear and cyclic siloxanes in ZIF-70 calculated from molecular dynamics simulations show that equilibrium can be reached on reasonable time scales. We explored vacuum-temperature swing adsorption (VTSA) as a potential method for the recovery of adsorbed linear siloxanes from ZIF-70, achieving a 75% reduction in adsorbed phase concentration. Additionally, we demonstrated that supercritical CO 2 offers an alternative desorption strategy by displacing adsorbed linear siloxanes in ZIF-70 at pressures above 200 bar driven by entropy effects.

Adsorption↗
DOE OSTI2022

Corrosion characteristics of Mo and TZM alloy for plasma facing components in molten lithium at 623 K

Here, in this study, the corrosion behaviours of molybdenum (Mo) and a Mo-based alloy (TZM) were investigated using a static immersion corrosion technique. Weight loss, surface microstructure, and corrosion depth of Mo and the TZM alloy were correlated with elements. The compatibility of Mo and the TZM alloy in static liquid Li was suitable. Mo demonstrated uniform corrosion with a homogenous dissolution of free C and Mo, and TZM alloy exhibited a nonuniform corrosion behaviour with a preferential grain boundary attack caused by the selective dissolution of free C, Ti, and Zr. When the surface oxidation layer of the samples was consumed, free C from Mo and TZM diffused into molten Li to form Li 2 C 2 and then was captured by Zr, Ti, and Mo to form thermodynamically stable carbides, which resulted in the enrichment of the C layer near the sample surfaces. In addition, Ti and Zr acted as N-trappers in liquid Li; the formation of Zr and Ti nitrides resulted in the enrichment of N, Ti, and Zr elements on the surface and led to TZM corrosion increase. Thus, Zr and Ti depletion, pitting, and grain boundary corrosion were problematic for TZM under long-term exposure to liquid Li. Reducing the content of free C and nonmetallic N and increasing the amount of Ti and Zr carbides on the surface of and inside the raw TZM alloy helped improve the corrosion resistance of TZM in liquid Li.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A systematic study of lanthanide titanates (A 2 Ti 2 O 7 ) chemical durability: corrosion mechanisms and control parameters

Dense lanthanide titanates ranging from La 2 Ti 2 O 7 to Yb 2 Ti 2 O 7 were synthesized by spark plasma sintering with similar micro-sized microstructure, and their chemical durability and degradation mechanisms were investigated by semi-dynamic leaching tests. Different corrosion mechanisms from incongruent to congruent dissolution were observed with preferential elemental releases of lanthanides in A 2 Ti 2 O 7 (A = La to Gd) and Ti in Er 2 Ti 2 O 7 and Yb 2 Ti 2 O 7 . Initial leaching was controlled by surface dissolution and long-term dissolution shifted to a diffusion-controlled mechanism for titanate pyrochlores from Sm 2 Ti 2 O 7 to Yb 2 Ti 2 O 7 . Both short-term and long-term leaching rates decreased from La 2 Ti 2 O 7 to Yb 2 Ti 2 O 7 , and materials became more corrosion resistant with decreasing ionic radius ratios of the rare-earth elements and titanium. Amorphous passivation films of several nm-thick enriched with Ti formed on the surfaces of the corroded materials, and the formation mechanisms were governed either by surface reorganization with preferential release of lanthanides or dissolution-precipitation from saturated bulk solutions with preferential release of titanium. Finally, these results demonstrate that the ionic size plays a dominant role in determining chemical durability of lanthanide titanates and a strong correlation is established among chemical composition/structural variation, passivation film formation and corrosion mechanisms, and materials chemical durability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗