Search NASA⌕ Search

SEARCH · Search NASA

Results for “pressure points”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

The Potential of Wearable Sensor Technology for EVA Glove Ergonomic Evaluation

Injuries to the hands are common among astronauts who train for extravehicular activity (EVA). Many of these injuries refer to the gloves worn during EVA as the root cause. While pressurized, the bladder and outer material of these gloves restrict movement and create pressure points while performing tasks, sometimes resulting in pain, muscle fatigue, abrasions, and occasionally a more severe injury, onycholysis (fingernail delamination). The most common injury causes are glove contact (pressure point/rubbing), ill-fitting gloves, and/or performing EVA tasks in pressurized gloves. A brief review of the Lifetime Surveillance of Astronaut Health's injury database reveals over 57% of the total injuries to the upper extremities during EVA training occurred either to the metacarpophalangeal (MCP) joint, fingernail, or the fingertip. Twenty-five of these injuries resulted in a diagnosis of onycholysis

Reid, Christopher R.↗
NASA NTRSDate not supplied

Analysis of Probe Surveys Conducted in the 10-MW TP3 Arc-Jet Facility 15-Inch Nozzle Flow

Computational simulations and analysis of flow characterization tests in a high enthalpy arc-jet facility at NASA Ames Research Center are reported. These tests were conducted in the 10-MW TP3 facility 15-inch conical nozzle, and pitot pressure and heat flux probes are used to survey test flow downstream of the nozzle exit. Two 1.59-cm (0.625 in) diameter hemisphere probes were used: one with a stagnation-point pressure port, the other with a Gardon heat flux gage. Calibration data were also obtained using 10.16-cm iso-q and 20.32-cm flat-faced slug calorimeters. Experimental surveys of arc-jet test flow with pitot pressure and heat flux probes were obtained at eight arc-heater conditions, covering wide ranges in arc current (316–1756 A) and mass flow rate (32–500 g/s, without any cold-gas injection at the arc-heater plenum) and providing assessment of the flow uniformity in the facility. The present analysis comprises computational fluid dynamics simulations of the nonequilibrium flowfield in the facility nozzle and test box, including the models tested. These simulations take into account non-uniform total enthalpy and mass flux profiles at the nozzle inlet as well as the expansion waves emanating from the nozzle exit and their effects on the model flowfields. Comparisons of computations with the experimental measurements are presented, showing reasonably good agreement. The probe survey data and accompanying analysis show that the test flow in the TP3 15-inch nozzle is highly non-uniform at most conditions, and the extent of flow non-uniformity depends on arc current and mass flow rate.

Arc-jets↗
NASA NTRSDate not supplied

Analysis of Probe Surveys Conducted in the 10-MW TP3 Arc-Jet Facility 15-Inch Nozzle Flow

Computational simulations and analysis of flow characterization tests in a high enthalpy arc-jet facility at NASA Ames Research Center are reported. These tests were conducted in the 10-MW TP3 facility 15-inch conical nozzle, and pitot pressure and heat flux probes are used to survey test flow downstream of the nozzle exit. Two 1.59-cm (0.625 in) diameter hemisphere probes were used: one with a stagnation-point pressure port, the other with a Gardon heat flux gage. Calibration data were also obtained using 20.32-cm flat-faced slug calorimeters. Experimental surveys of arc-jet test flow with pitot pressure and heat flux probes were obtained at eight arc-heater conditions, covering wide ranges in arc current (316–1756 A) and mass flow rate (32–500 g/s, without any cold-gas injection at the arc-heater plenum) and providing assessment of the flow uniformity in the facility. The present analysis comprises computational fluid dynamics simulations of the nonequilibrium flowfield in the facility nozzle and test box, including the models tested. These simulations take into account non-uniform total enthalpy and mass flux profiles at the nozzle inlet as well as the expansion waves emanating from the nozzle exit and their effects on the model flowfields. Comparisons of computations with the experimental measurements are presented, showing reasonably good agreement. The probe survey data and accompanying analysis show that the test flow in the TP3 15-inch nozzle is highly non-uniform at most conditions, and the extent of flow non-uniformity depends on arc current and mass flow rate.

Arc-jets↗
NASA NTRS1980

Aerodynamic performances of three fan stator designs operating with rotor having tip speed of 337 meters per second and pressure ratio of 1.54. 1: Experimental performance

The aerodynamic performances of four stator-blade rows are presented and evaluated. The aerodynamic designs of two of these stators were compromised to reduce noise, a third design was not. On a calculated operating line passing through the design point pressure ratio, the best stator had overall pressure-ratio and efficiency decrements of 0.031 and 0.044, respectively, providing a stage pressure ratio of 1.483 and efficiency of 0.865. The other stators showed some correctable deficiencies due partly to the design compromises for noise. In the end-wall regions blade-element losses were significantly less for the shortest chord studied.

Gelder, T. F.↗
DOE OSTI2023

A Quenched Disorder in the Quantum-Critical Superconductor CeCoIn 5

Emergent inhomogeneous electronic phases in metallic quantum systems are crucial for understanding high- T c superconductivity and other novel quantum states. In particular, spin droplets introduced by nonmagnetic dopants in quantum-critical superconductors (QCSs) can lead to a novel magnetic state in superconducting phases. However, the role of disorders caused by nonmagnetic dopants in quantum-critical regimes and their precise relation with superconductivity remain unclear. Here, the systematic evolution of a strong correlation between superconductive intertwined electronic phases and antiferromagnetism in Cd-doped CeCoIn 5 is presented by measuring current–voltage characteristics under an external pressure. In the low-pressure coexisting regime where antiferromagnetic (AFM) and superconducting (SC) orders coexist, the critical current ( I c ) is gradually suppressed by the increasing magnetic field, as in conventional type-II superconductors. At pressures higher than the critical pressure where the AFM order disappears, I c remarkably shows a sudden spike near the irreversible magnetic field. In addition, at high pressures far from the critical pressure point, the peak effect is not suppressed, but remains robust over the whole superconducting region. These results indicate that magnetic islands are protected around dopant sites despite being suppressed by the increasingly correlated effects under pressure, providing a new perspective on the role of quenched disorders in QCSs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1992

Atmospheric entry of nuclear-powered vehicles due to accidental/inadvertent termination of operations

The entries of the radioactive components into earth's atmosphere resulting from an accident or inadvertent abort of a space vehicle powered by nuclear-thermal-rockets are investigated. The study is made for a typical piloted Mars mission vehicle incapacitated by an accident or malfunction during the trans-Mars-injection maneuver due to simultaneous multiple failures of its component systems. The three different accident/abort modes considered are the following: (1) a constant-rate angular pitching motion of the vehicle, (2) a constant-acceleration angular pitching motion of the vehicle, and (3) the rocket engine breaks away from the rest of the vehicle with a finite relative (dispersion) velocity. The speeds and angles of the atmospheric entries are calculated for each mode for different values of the time of the accident, pitching rate, acceleration, and dispersion velocity. For the most severe entry speeds and flight-path angles, the stagnation-point pressures, heat transfer rates, thickness, and mass per unit area of the heat shields necessary to protect the radioactive components from disintegrating, deceleration g-loads, and high ground-impact velocities are calculated. The study points out that the high g-loads and high ground-impact velocities are the most serious problems that must be addressed.

Menees, Gene P.↗
NASA NTRS1986

Comparison of theoretical and flight-measured local flow aerodynamics for a low-aspect-ratio fin

Flight test and theoretical aerodynamic data were obtained for a flight test fixture mounted on the underside of an F-104G aircraft. The theoretical data were generated using two codes: a two-dimensional transonic code called code H, and a three-dimensional subsonic and supersonic code called wing-body. Pressure distributions generated by the codes for the flight test fixture, as well as compared with the flight-measured data. The two-dimensional code pressure distributions compared well except at the minimum pressure point and the trailing edge. Shock locations compared well except at high transonic speeds. However, the two-dimensional code did not adequately predict the displacement thickness of the flight test fixture. The three-dimensional code pressure distributions compared well except at the trailing edge of the flight test fixture.

Johnson, J. Blair↗
NASA NTRS1974

Effects of viscoelasticity on cavitation in drag reducing fluids

To study cavitation inception in polymer solutions, a blow-down water tunnel with short running times was used. Tests were made using 1/4 and 1/2 inch diameter models of hemispherical-nose cylinders. To accurately detect the inception of cavitation, a reliable technique was developed using a continuously operating He-Ne gas laser. The laser beam was adjusted to grazing incidence with the model at the minimum pressure point where cavitation inception was to be expected. A sensitive photocell was placed at ninety degrees to detect the beam. As incipient cavitation occurred, the bubbles caused scattering of the laser beam which was picked up by the photocell. Static pressure near the model in the working section of the tunnel was measured using a solid-state pressure pick-up. The signals from the photocell and the pressure pick-up were recorded on an oscillograph. Velocity field visualization was achieved using one microsecond duration light pulses scattered by small polystryrene latex spheres in the flow.

Ting, R. Y.↗
DOE OSTI2024

Thermally frustrated phase transition at high pressure in B 2-ordered FeV

X-ray diffraction measurements of equiatomic B2-ordered FeV were performed in a diamond-anvil cell at room temperature at several pressure points up to 80 GPa that showed the cubic phase to be stable with no indication of structural phase transitions. Density functional theory at 0 K predicts Fermi surface nesting, an electronic topological transition, and a phonon dynamical instability within the experimentally investigated pressure range. Nevertheless, the instability is absent in phonon dispersion curves extracted from ab initio molecular dynamics simulations below the critical volume at temperatures as low as 10 K, indicating that thermal atomic displacements can frustrate the phase transition by renormalizing the phonon dispersion curves. Ferrimagnetism is critical for the stability of the cubic phase at low temperature, but thermal atomic displacements are enough to support the structure at and above the Néel temperature.

36 MATERIALS SCIENCE↗
NASA NTRS1979

Energy efficient engine: High pressure turbine uncooled rig technology report

Results obtained from testing five performance builds (three vane cascades and two rotating rigs of the Energy Efficient Engine uncooled rig have established the uncooled aerodynamic efficiency of the high-pressure turbine at 91.1 percent. This efficiency level was attained by increasing the rim speed and annulus area (AN(2)), and by increasing the turbine reaction level. The increase in AN(2) resulted in a performance improvement of 1.15 percent. At the design point pressure ratio, the increased reaction level rig demonstrated an efficiency of 91.1 percent. The results of this program have verified the aerodynamic design assumptions established for the Energy Efficient Engine high-pressure turbine component.

Gardner, W. B.↗
NASA NTRS1990

Pressure-based real-time measurements in compressible free shear layers

A preliminary experimental study has been conducted to gain insight into the temporal and spatial contents of largescale structures in a convective Mach number = 0.51 high Reynolds number planar two-dimensional compressible free shear layer. Power spectra, coherence, and space-time correlations were obtained using single- and two-point pressure measurements. Both developing and fully developed regions of the flow were investigated. The passage frequency of structures were found to be 10-15 kHz in the developing region and 4-8 kHz in the fully developed region. The convective velocity obtained from the space-time correlation in the middle of the shear layer was close to the theoretical value but varied toward the edge of the shear layer. The structures were shown to be surprisingly three-dimensional even in this low compressibility level shear layer. The structures size and spacing were also determined and discussed.

Samimy, M.↗
NASA NTRS2015

Feasibility Assessment of an EVA Glove Sensing Platform to Evaluate Potential Hand Injury Risk Factors

Injuries to the hands are common among astronauts who train for extravehicular activity (EVA). When the gloves are pressurized, they restrict movement and create pressure points during tasks, sometimes resulting in pain, muscle fatigue, abrasions, and occasionally more severe injuries such as onycholysis. A brief review of the Lifetime Surveillance of Astronaut Health's injury database reveals that 58% of total astronaut hand and arm injuries from NBL training between 1993 and 2010 occurred either to the fingernail, MCP, or fingertip. The purpose of this study was to assess the potential of using small sensors to measure force acting on the fingers and hand within pressurized gloves and other variables such as blood perfusion, skin temperature, humidity, fingernail strain, skin moisture, among others. Tasks were performed gloved and ungloved in a pressurizable glove box. The test demonstrated that fingernails saw greater transverse strain levels for tension or compression than for longitudinal strain, even during axial fingertip loading. Blood perfusion peaked and dropped as the finger deformed during finger presses, indicating an initial dispersion and decrease of blood perfusion levels. Force sensitive resistors to force plate comparisons showed similar force curve patterns as fingers were depressed, indicating suitable functionality for future testing. Strategies for proper placement and protection of these sensors for ideal data collection and longevity through the test session were developed and will be implemented going forward for future testing.

Reid, Christopher R.↗
NASA NTRS2016

Analysis of Potential Glove-Induced Hand Injury Metrics During Typical Neutral Buoyancy Training Operations

Injuries to the hands are common among astronauts who train for extravehicular activity. When the gloves are pressurized, they restrict movement and create pressure points during tasks, sometimes resulting in pain, muscle fatigue, abrasions, and occasionally more severe injuries such as onycholysis. A brief review of NASA's Lifetime Surveillance of Astronaut Health's injury database reveals that 76 percent of astronaut hand and arm injuries from training between 1993 and 2010 occurred either to the fingernail, finger crotch, metacarpophalangeal joint, or fingertip. The purpose of this study was to assess the potential of using small sensors to measure forces acting on the fingers and hand within pressurized gloves and other variables such as skin temperature, humidity, and fingernail strain of a NASA crewmember during typical NBL (Neutral Buoyancy Laboratory) training activity. During the 5-hour exercise, the crewmember seemed to exhibit very large forces on some fingers, resulting in higher strain than seen in previous glove-box testing. In addition, vital information was collected on the glove cavity environment with respect to temperature and humidity. All of this information gathered during testing will be carried forward into future testing, potentially in glove-box- or 1G- (1 gravitational force) or NBL-suited environments, to better characterize and understand the possible causes of hand injury amongst NASA crew.

McFarland, Shane↗
NASA NTRSDate not supplied

Uranus Probe Entry and Descent Mission Concept

Introduction: Uranus was identified as the third highest priority flagship mission in the 2012-2022 Planetary Science Decadal Survey. This latest concept study was requested by the Decadal Survey panel to determine NASA’s planetary science priorities from 2022-2032. This study focused on the probe’s entry and descent aspects and associated trades for viable trajectory options. Uranus Mission and Descent Probe: The proposed Uranus Orbiter and Probe (UOP) Flagship mission will investigate Uranus and its surrounding moons using an orbiting spacecraft with a Uranus descent probe. Unlike previous studies the probe release will occur after orbit insertion allowing sufficient separation of critical events during the orbit insertion burn. The probe will be released at an altitude that allows one hour of in situ atmospheric readings that will be relayed to the orbiter. Afterwards the orbiter will transition to the moon tour phase of the mission. The configuration chosen for the entry aeroshell was a 45° sphere-cone. This shape has been used in the past in the Pioneer Venus Galileo missions. However, the nose radius considered in the present study differed from the values used in either of the previous configurations, primarily to reduce the heat flux at the stagnation point. A two-step approach was used in the development of flight trajectories for the chosen configuration. In the first step, the trajectory code POST2 was used to screen the thousands of entry states provided by interplanetary trajectory simulations, which were terminated at an altitude of 2000 km from the reference surface (1 bar) of Uranus. The screening criteria were: (i) optimization of the communication geometry between the entry probe and orbiter to ensure at least 1 hour of science measurements, (ii) peak stagnation point pressures to be less than six bar, (iii) peak heat fluxes to be less than 5 kW/cm2; the latter two constraints being the limits of ground-test capabilities of the arc jets at NASA Ames Research Center. The entry team investigated two trajectories that met the criteria above, a shallow entry (high heat load ~44 kJ/cm2) and a steeper entry (high heat rate ~1950 W/cm2). In the second step, the two bounding candidate entry states from the POST2 screening process were used in developing flight trajectories using TRAJ coupled with FIAT (a materials thermal response and sizing code) and a margins policy to determine a margined uniform thickness (hence mass) of the forward heatshield material based on the aerothermal environments at the stagnation point. Since the combination of TRAJ and FIAT size the TPS based on stagnation point environments only, flow field computations using DPLR were necessary to determine turbulent aerothermal environments on the conical flank, and the augmentation of these environments due to surface roughness. The environments at select locations on the forward heatshield were then used to size the thermal protection material, with the largest thickness value then used to estimate the mass. The newly developed woven thermal protection material –HEEET (Heatshield for Extreme Entry Environments Technology) –was considered for the forward heatshield and PICA (Phenolic-Impregnated Carbon Ablator) was considered for the backshell. These NASA-developed materials are at TRL 6 and TRL 9, respectively. Furthermore, two options were considered for the HEEET material: (i) a dual-layer option with a denser recession layer on top and an insulative layer underneath it, and (ii) a single layer option consisting of the insulative layer alone. Results: It is clear that probe entry states are feasible and the selected TPS options are able to perform in the predicted aerothermal environments thus enabling the mission to meet of the descent probe portion of this flagship mission

Entry Descent and Landing↗
DOE OSTI2025

High Pressure Synthesis of Pr 2 O 5 – A Unique Lanthanoid(IV) Oxide Peroxide

Abstract Reacting praseodymium(IV) oxide with oxygen at 27 GPa in a diamond anvil cell yielded the oxide peroxide Pr 2 IV (O 2 )O 3 , which was characterized by single crystal X‐ray diffraction on multi‐grain samples, Raman spectroscopy and quantum theoretical calculations at various pressure points. The presence of tetravalent praseodymium ions is supported by electronic structure calculations, showing a band gap of ca. 1.2 eV, which is consistent with the anticipated chemical model of an ionic solid. Pr 2 (O 2 )O 3 thus far represents the most oxygen rich phase of any binary compound of a lanthanoid and oxygen and is the first example of a peroxide anion next to Pr 4+ . Additionally, these results demonstrate that instead of oxidizing the praseodymium ions past their +IV oxidation state, oxygen undergoes a comproportionation to form peroxide anions. Direct oxidation of the oxide anions by Pr 4+ ‐ions was ruled out by a control experiment in argon instead of oxygen, where no oxidation of oxide ions was observed.

Chemistry↗
DOE OSTI2022

Dynamic compression of Ce and Pr with millisecond time-resolved X-ray diffraction

Abstract Both cerium (Ce) and praseodymium (Pr) undergo a volume collapse transition under compression that originate from similar electronic mechanisms. Yet the outcome could not be more different. In the case of Ce with one affected 4f electron the volume collapse leaves the crystal symmetry intact, whereas for Pr with two 4f electrons the crystal symmetry changes from a distorted face centered cubic structure to a lower symmetry orthorhombic structure. In this paper, we present a study of the effect of strain/compression rate spanning nearly 4 orders of magnitude on the volume collapse phase transitions in Ce and Pr. These dynamic compression experiments in a diamond anvil cell also reveal kinetic differences between the phase transformations observed in these two materials. The transition cannot be overdriven in pressure in Ce, which indicates a fast kinetic process, whereas fast compression rates in Pr lead to a shift of the phase boundary to higher pressures, pointing to slower kinetics possibly due to the realization of a new crystal structure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Mixture Model for Refrigerant Pairs R-32/1234yf, R-32/1234ze(E), R-1234ze(E)/227ea, R-1234yf/152a, and R-125/1234yf

In this work, thermodynamic models based on the corresponding states framework with departure terms are developed for the refrigerant pairs R-32/1234yf, R-32/1234ze(E), R-1234ze(E)/227ea, R-1234yf/152a, and R-125/1234yf. These models are based on new measurements of density, speed of sound, and phase equilibria, combined with the data available in the literature. The model for R-32/1234yf is most comprehensive in its data coverage, with speed of sound deviations within 1%, density deviations within 0.1%, and bubble- and dew-point pressure deviations within 1%. In conclusion, the other mixtures have generally more limited data availability but a similar goodness of fit.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Dielectric Fluids for the Direct Forced Convection Cooling of Power Electronics

The future of electrification of vehicles and other systems will require the creation of high-power density power electronics with low junction-to-fluid thermal resistance cooling solutions. One way to create this solution is to move high-heat-flux liquid cooling (single- or two-phase) as close to the power electronics components as possible. One novel approach involves submersion in dielectric fluids as the cooling solution. We first provide the range of fluid properties and develop a figure of merit (FOM) to aid in dielectric fluid selection. Next, we perform computational fluid dynamics/heat transfer (CFD/HT) modeling using single-phase cooling (submerged jet impingement on an enhanced surface) to validate the dielectric fluid FOM. Results of the study show that the developed FOM is a good representation of the performance of the fluids when compared to the results of the CFD/HT analysis. Both FOM and the CFD/HT analysis show that based on pure thermohydraulic considerations, several commercially available fluids present higher performance, on the order of 5% of water. Finally, the FOM can be used to quickly assess the thermohydraulic performance of a dielectric fluid, as well as the secondary application-specific properties such as boiling point, saturation pressure, flash point, and global warming potential, thereby allowing for fluid candidates to be readily compared.

computational fluid dynamics↗