Search NASA⌕ Search

SEARCH · Search NASA

Results for “primary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Effects of the LBV Primary's Mass-loss Rate on the 3D Hydrodynamics of eta Carinae's Colliding Winds

At the heart of eta Carinae's spectacular "Homunculus" nebula lies an extremely luminous (L(sub Total) greater than approximately 5 × 10(exp 6) solar luminosity) colliding wind binary with a highly eccentric (e approximately 0.9), 5.54-year orbit (Figure 1). The primary of the system, a Luminous Blue Variable (LBV), is our closest (D approximately 2.3 kpc) and best example of a pre-hypernova or pre-gamma ray burst environment. The remarkably consistent and periodic RXTE X-ray light curve surprisingly showed a major change during the system's last periastron in 2009, with the X-ray minimum being approximately 50% shorter than the minima of the previous two cycles1. Between 1998 and 2011, the strengths of various broad stellar wind emission lines (e.g. Halpha, Fe II) in line-of-sight (l.o.s.) also decreased by factors of 1.5 - 3 relative to the continuum2. The current interpretation for these changes is that they are due to a gradual factor of 2 - 4 drop in the primary's mass-loss rate over the last approximately 15 years1, 2. However, while a secular change is seen for a direct view of the central source, little to no change is seen in profiles at high stellar latitudes or reflected off of the dense, circumbinary material known as the "Weigelt blobs"2, 3. Moreover, model spectra generated with CMFGEN predict that a factor of 2 - 4 drop in the primary's mass-loss rate should lead to huge changes in the observed spectrum, which thus far have not been seen. Here we present results from large- (plus or minus 1620 AU) and small- (plus or minus 162 AU) domain, full 3D smoothed particle hydrodynamics (SPH) simulations of eta Car's massive binary colliding winds for three different primary-star mass-loss rates (2.4, 4.8, and 8.5 × 10(exp -4) solar mass/yr). The goal is to investigate how the mass-loss rate affects the 3D geometry and dynamics of eta Car's optically-thick wind and spatially-extended wind-wind collision (WWC) regions, both of which are known sources of observed X-ray, optical, UV, and near-IR emission and absorption. We use two domain sizes in order to better understand how the primary's mass-loss rate influences the various observables that form at different length scales. The 3D simulations provide information important for helping constrain η Car's recent mass-loss history and future state.

lavestigate↗
NASA NTRS2016

Primary Dendrite Arm Spacing and Trunk Diameter in Al-7-Weight-Percentage Si Alloy Directionally Solidified Aboard the International Space Station

Under a NASA-ESA collaborative research project, three Al-7-weight-percentage Si samples (MICAST-6, MICAST-7 and MICAST 2-12) were directionally solidified aboard the International Space Station to determine the effect of mitigating convection on the primary dendrite array. The samples were approximately 25 centimeters in length with a diameter of 7.8 millimeter-diameter cylinders that were machined from [100] oriented terrestrially grown dendritic Al-7Si samples and inserted into alumina ampoules within the Sample Cartridge Assembly (SCA) inserts of the Low Gradient Furnace (LGF). The feed rods were partially remelted in space and directionally solidified to effect the [100] dendrite-orientation. MICAST-6 was grown at 5 microns per second for 3.75 centimeters and then at 50 microns per second for its remaining 11.2 centimeters of its length. MICAST-7 was grown at 20 microns per second for 8.5 centimeters and then at 10 microns per second for 9 centimeters of its remaining length. MICAST2-12 was grown at 40 microns per second for 11 centimeters. The thermal gradient at the liquidus temperature varied from 22 to 14 degrees Kelvin per centimeter during growth of MICAST-6, from 26 to 24 degrees Kelvin per centimeter for MICAST-7 and from 33 to 31 degrees Kelvin per centimeter for MICAST2-12. Microstructures on the transverse sections along the sample length were analyzed to determine nearest-neighbor spacing of the primary dendrite arms and trunk diameters of the primary dendrite-arrays. This was done along the lengths where steady-state growth prevailed and also during the transients associated with the speed-changes. The observed nearest-neighbor spacings during steady-state growth of the MICAST samples show a very good agreement with predictions from the Hunt-Lu primary spacing model for diffusion controlled growth. The observed primary dendrite trunk diameters during steady-state growth of these samples also agree with predictions from a coarsening-based model. The radial macrosegregation and "steepling" caused by thermosolutal convection during terrestrial growth of the Al-7Si was not observed in the space-grown MICAST samples.

Ghods, M.↗
NASA NTRS2019

Consensus on Aquatic Primary Productivity Field Protocols for Satellite Validation and Model Synthesis

The NASA PACE project, in conjunction with the IOCCG, EUMETSAT, and JAXA, have initiated an Aquatic Primary Productivity working group, with the aim to develop community consensus on multiple methods for measuring aquatic primary productivity used for satellite validation and model synthesis. A workshop to commence the working group efforts was held December 05-07, 2018 at the University Space Research Association headquarters in Columbia, MD U.S.A., bringing together 26 active researchers from 16 institutions. The group discussed the primary differences, nuances, scales, uncertainties, definitions, and best practices for measurements of primary productivity derived from in situ/on-deck/laboratory radio/stable isotope incubations, dissolved oxygen concentrations (from incubations or autonomous platforms such as floats or gliders), oxygen-argon ratios, triple oxygen isotope, natural fluorescence, and FRRF/ETR/kinetic analysis. These discussions highlighted the necessity to move the community forward towards the establishment of climate-quality primary productivity measurements that follow uniform protocols, which is imperative to ensure that existing and future measurements can be compared, assimilated, and their uncertainties determined for model development and validation. The specific deliverable resulting from of this activity will be a protocol document, published in coordination with the IOCCG. This presentation will discuss the findings of the meeting, and address future activities of the working group.

Vandermeulen, Ryan A.↗
NASA NTRS2006

A comparison of global estimates of marine primary production from ocean color

The third primary production algorithm round robin (PPARR3) compares output from 24 models that estimate depth-integrated primary production from satellite measurements of ocean color, as well as seven general circulation models (GCMs) coupled with ecosystem or biogeochemical models. Here we compare the global primary production fields corresponding to eight months of 1998 and 1999 as estimated from common input fields of photosynthetically-available radiation (PAR), sea-surface temperature (SST), mixed-layer depth, and chlorophyll concentration. We also quantify the sensitivity of the ocean-color-based models to perturbations in their input variables. The pair-wise correlation between ocean-color models was used to cluster them into groups or related output, which reflect the regions and environmental conditions under which they respond differently. The groups do not follow model complexity with regards to wavelength or depth dependence, though they are related to the manner in which temperature is used to parameterize photosynthesis. Global average PP varies by a factor of two between models. The models diverged the most for the Southern Ocean, SST under 10 C, and chlorophyll concentration exceeding 1mg Chlm-3. Based on the conditions under which the model results diverge most, we conclude that current ocean-color-based models are challenged by high-nutrient low-chlorophyll conditions, and extreme temperatures or chlorophyll concentrations. The GCM-based models predict comparable primary production to those based on ocean color: they estimate higher values in the Southern Ocean, at low SST, and in the equatorial band, while they estimate lower values in eutrophic regions (probably because the area of high chlorophyll concentrations is smaller in the GCMs). Further progress in primary production modeling requires improved understanding of the effect of temperature on photosynthesis and better parameterization of the maximum photosynthetic rate.

Yamanaka, Yasuhiro↗
NASA NTRSDate not supplied

Quantifying Primary Arc-Induced Degradation of Perovskite Solar Cells

Primary arcing induced by spacecraft charging presents a significant hazard to thin film solar cells if left unchecked. Here, we present the results of a preliminary effort to quantify the impacts of primary arcing to perovskite solar cells. Solar cells operating in a charged environment are susceptible to electrostatic discharges known as arcing. While primary arcs are not generally considered a major concern for traditional space PV, for thin film cells, these can induce significant heating and subsequent damage. We conducted ESD testing in a LEO-like plasma in the National Plasma Interaction Facility at NASA Glenn Research Center to quantify impacts to cell performance by arcing. The perovskites tested saw a decrease of short circuit current with an increased number of arcs, averaging a relative change of 73.89 ± 15.90% after 60 total arcs supplied a cumulative energy dose of 76.12 mJ to the string. Ongoing work entails testing with larger perovskite data sets and expanding to include additional thin film cell technologies to demonstrate the risk unmitigated primary arcing presents.

primary arcing↗
DOE OSTI2025

Printed circuit primary heat exchanger for power conversion in heat pipe microreactor applications

Here, in the present study, a model was developed for a recuperated air Brayton cycle for heat pipe microreactors, and the effect of the primary heat exchanger type assessed. An annular flow heat exchanger and a printed circuit heat exchanger (PCHE) were evaluated. A sub-sized diffusion bonded, PCHE test specimen was manufactured and tested with nitrogen as the working fluid to validate and improve the PCHE model. A comparison of the thermal cycle efficiency for the Brayton cycle coupled to a heat pipe microreactor using each of the two primary heat exchangers showed competitive performance for both options, with achievable cycle efficiencies of 34 % and 35 % for the annular and printed circuit heat exchangers, respectively. The impact of heat pipe length and additional reheating stages on cycle efficiency was studied. Increasing the heat pipe condenser length from 0.8 to 2.0 m resulted in an increase in cycle efficiency of 3.5 % and 3.2 % for the annular and printed circuit heat exchangers, respectively. The use of additional reheating stages showed a reduction in cycle efficiency since the heat pipe surface area limits the primary heat exchanger size and effectiveness. These results highlight the importance of the primary heat exchanger on the performance of a heat pipe microreactor. Overall, the cycle model, testing, and heat exchanger model showed the potential for the PCHE to improve the economics of a heat pipe microreactor relative to the annular flow heat exchanger, which also opens the possibility to use different heat transfer fluids such as supercritical CO 2 .

PCHE↗
DOE OSTI2025

Controlled electrochemical nutrient delivery to enhance marine primary productivity

Oceanic photosynthesis contributes to approximately half of the Earth’s net annual primary productivity. Marine photosynthetic productivity has a high degree of heterogeneity due to spatial and temporal co-limitations of light, temperature, and/or nutrients. Across coastal, near-shore, and open ocean regions, insufficient concentrations of key nutrients (e.g., N, P, Fe) can limit primary productivity. Although studies have shown a significant increase in primary productivity with the addition of low doses of trace nutrients, a sustainable approach to reliably deliver and maintain low doses of nutrients and ensure their bioavailability, remains a challenge. Chemical nutrient addition has relied on the use of chelating agents to ensure nutrient bioavailability, but synthetic chelators are persistent environmental pollutants. In this study, we demonstrate for the first time the use of a controlled electrochemical nutrient delivery (CEND) approach to accelerate the growth of phytoplankton without the need for such chelators. Our study uses commercial stainless-steel electrodes to deliver low concentrations of iron to enhance growth rates in the microalga Picochlorum celeri TG2. To demonstrate the process control offered by the CEND method, we evaluate iron delivery as a function of pulse time, pulse frequency, and rest time between pulses. Our data show that at the same total Fe dose of 163 ppb, electrochemical iron delivery can achieve 9.54 ± 0.58 mg biomass/µg Fe, which is comparable to 9.14 ± 0.17 mg biomass/µg Fe achieved with chemical iron additions that include the synthetic chelating agent ethylenediaminetetraacetic acid (EDTA). Further, when different total iron doses (163 ppb, 325 ppb, and 650 ppb) were delivered over 72 h using CEND, biomass yield per iron dose was higher at lower doses: 9.54 ± 0.58 mg biomass/µg Fe at 163 ppb vs. 4.32 ± 0.32 mg biomass/µg Fe at 650 ppb. This highlights the benefits of CEND in delivering frequent and low doses of nutrients for improved process efficiency. Preliminary assessments show both lower cost and reduced greenhouse gas emissions from electrochemical over chemical iron additions with EDTA. The CEND approach opens new pathways to enhance marine primary productivity, without the unintended environmental impacts of synthetic chelators.

analytical chemistry↗
NASA NTRS1982

Good imaging with very fast paraboloidal primaries - An optical solution and some applications

Attention is given to the imaging performance improvement obtainable in telescopes with fast parabolic primaries by means of two-mirror correctors of the Paul-Baker type. Images with 80 percent of the energy concentrated within 0.2 arcsec are projected for an f/1 primary relaying to an f/2 final focus, over a 1 deg-diameter field. It is noted that the mechanical structure and enclosure of a large telescope built with these fast optics should be significantly smaller and less expensive than those for conventional optics. The application of the Paul-Baker corrector system is explored for such diverse telescope types as those employing six off-axis primary mirrors, UV astronomy telescopes with no chromatic aberration, a low emissivity IR astronomy instrument with an off-axis f/1 parent primary mirror part, and thin rectangular aperture telescopes which are useful for spectroscopy and photometry.

Angel, J. R. P.↗
NASA NTRS1984

Microwave and X-ray observations of delayed brightenings at sites remote from the primary flare locations

Five examples of solar flares observed with the 17-GHz interferometer at Nobeyama in which a secondary microwave burst occurred at a distance of 100,000 km to 1,000,000 km from the primary flare site are presented. The secondary microwave burst in all five cases had a similar time profile to the primary burst with a delay of 2 to 25 s. The velocity of a triggering agent inferred from this delay and spatial separation is 10,000 km to 100,000 km/s. The intensity of the secondary burst was a factor of 3 to 25 smaller than that of the primary burst in all events except for one case in which it was a factor of 2 larger. The polarization degree of the secondary burst at 17 GHz was 35%, significantly higher than the average value for typical impulsive bursts. Two of the events were accompanied by meterwave type III/V bursts located high in the corona between the primary and secondary sites. For two of the other events, X-ray images of he secondary source were obtained with the hard-X-ray imaging spectrometer on the Solar Maximum Mission. These observations strongly suggest that the distant microwave bursts were produced by electrons with energies of 10 keV to 100 keV which were channeled along a huge loop from the main flare site to the remote location.

Nakajima, H.↗
NASA NTRS1983

Cosmic-ray antimatter - A primary origin hypothesis

The present investigation is concerned with the possibility that the observed cosmic-ray protons are of primary extragalactic origin, taking into account the significance of the current antiproton data. Attention is given to questions regarding primary antiprotons, antihelium fluxes, and the propagation of extragalactic cosmic rays. It is concluded that the primary origin hypothesis should be considered as a serious alternative explanation for the cosmic-ray antiproton fluxes. Such extragalactic primary origin can be considered in the context of a baryon symmetric domain cosmology. The fluxes and propagation characteristics suggested are found to be in rough agreement with the present antiproton data.

Stecker, F. W.↗
NASA NTRS1985

Cosmogenic-nuclide production by primary cosmic-ray protons

The production rates of cosmogenic nuclides were calculated for the primary protons in the galactic and solar cosmic rays. At 1 AU, the long-term average fluxes of solar protons usually produce many more atoms of cosmogenic nuclide than the primary protons in the galactic cosmic rays (GCR). Because the particle fluxes inside meteorites and other large objects in space include many secondary neutrons, the production rates and ratios inside large objects are often very different from those by just the primary GCR protons. It is possible to determine if a small object, was small in space or broken from a meteorite. Because heliospherical modulation and other interactions change the GCR particle spectrum, the production of cosmogenic nuclides by the GCR particles outside the heliosphere will be different from that by modulated GCR primaries.

Reedy, R. C.↗
NASA NTRS1985

Microwave and X-ray observations of delayed brightenings at sites remote from the primary flare locations

Five examples of solar flares observed with the 17-GHz interferometer at Nobeyama in which a secondary microwave burst occurred at a distance of 100,000 km to 1,000,000 km from the primary flare site are presented. The secondary microwave burst in all five cases had a similar time profile to the primary burst with a delay of 2 to 25 s. The velocity of a triggering agent inferred from this delay and spatial separation is 10,000 km to 100,000 km/s. The intensity of the secondary burst was a factor of 3 to 25 smaller than that of the primary burst in all events except for one case in which it was a factor of 2 larger. The polarization degree of the secondary burst at 17 GHz was 35 percent, significantly higher than the average value for typical impulsive bursts. Two of the events were accompanied by meterwave type III/V bursts located high in the corona between the primary and secondary sites. For two of the other events, X-ray images of the secondary source were obtained with the hard-X-ray imaging spectrometer on the Solar Maximum Mission. These observations strongly suggest that the distant microwave bursts were produced by electrons with energies of 10 keV to 100 keV which were channeled along a huge loop from the main flare site to the remote location.

Nakajima, H.↗
NASA NTRS1987

Primary quantum yields of NO2 photodissociation

The quantum yields of formation of NO, O2, and NO2 loss are measured for NO2 vapor at low pressures (0.13-0.30 torr) irradiated at 334-405 nm wavelengths and temperature in the range 273-370 K in order to study the primary quantum efficiencies of NO2 photodecomposition. The temperature and wavelength dependences of the primary quantum efficiencies are examined. It is observed that the primary quantum efficiencies increase rapidly from near zero at 424 nm to near unity for excitation at wavelengths less than 394 nm. The theory of Pitts et al. (1964) that the energy deficiency for photodissociation of NO2 excited at wavelengths greater than 397.9 nm is due to the rotational and vibrational energy of the NO2 molecules is confirmed by the data. Values for the primary quantum yields of NO2 photodecomposition as a function of wavelength are presented.

Gardner, Edward P.↗
NASA NTRS1989

A multi-sensor remote sensing approach for measuring primary production from space

It is proposed to develop a multi-sensor remote sensing method for computing marine primary productivity from space, based on the capability to measure the primary ocean variables which regulate photosynthesis. The three variables and the sensors which measure them are: (1) downwelling photosynthetically available irradiance, measured by the VISSR sensor on the GOES satellite, (2) sea-surface temperature from AVHRR on NOAA series satellites, and (3) chlorophyll-like pigment concentration from the Nimbus-7/CZCS sensor. These and other measured variables would be combined within empirical or analytical models to compute primary productivity. With this proposed capability of mapping primary productivity on a regional scale, we could begin realizing a more precise and accurate global assessment of its magnitude and variability. Applications would include supplementation and expansion on the horizontal scale of ship-acquired biological data, which is more accurate and which supplies the vertical components of the field, monitoring oceanic response to increased atmospheric carbon dioxide levels, correlation with observed sedimentation patterns and processes, and fisheries management.

Gautier, Catherine↗
NASA NTRS1990

Primary arm spacing in directionally solidified Pb-10 wt percent Sn alloys

The dependence of primary arm spacings on growth speed was investigated for cellular and dendritic arrays in Pb-10 wt percent Sn samples directionally solidified under a constant positive thermal gradient in the melt. The gradient of constitutional supercooling was varied from almost zero (near the break-down of the planar liquid-solid interface at small growth speeds, cellular morphology) to near unity (large growth speeds, dendritic morphology). The spatial arrangements of cells and dendrites, as given by their coordination number, are not very different from each other. It appears that primary arm spacing maxima and the cell to dendrite transition are strongly influenced by the magnitude of the solute partition coefficient. The planar to cellular bifurcation is supercritical in Pb-Sn which has a high partition coefficient, as compared to the subcritical behavior reported in Al-Cu and succinonitrile-acetone, both of which have low partition coefficients. The primary arm spacing model due to Hunt agrees with the experimentally observed trend for the whole growth regime. There is a good quantitative agreement at higher gradients of supercooling. However, the model overpredicts the primary arm spacings at low gradients of constitutional supercooling.

Chopra, M. A.↗
NASA NTRS1989

Primary zone dynamics in a gas turbine combustor

Fluid mechanical investigations simulating the flow in the primary zone of a gas turbine combustor are presented using three generic test rigs: (1) rotating pipe yielding a swirling jet of air; (2) primary zone model with a single swirler and various primary jet configurations, operated with air; and (3) two rectangular models of a (stretched-out) annular combustor with five swirlers in the backwall and with various primary jet configurations, one operated with air and the other with water. Concentration measurements are obtained using laser sheet imaging techniques and velocity measurements using a laser Doppler velocimeter. The results show recirculation zones, intense mixing, instabilities of the interacting jets and the presence of large random vortical motions. The flowfields are shown to exhibit bimodal behavior, have asymmetries despite symmetrical geometry and inlet conditions and display strong jet/swirler and swirler/swirler interactions.

Sullivan, J. P.↗
NASA NTRS1990

Primary arm spacing in directionally solidified Pb-10 wt pct Sn alloys

The dependence of primary arm spacings on growth speed was investigated for cellular and dendritic arrays in Pb-10 wt percent Sn samples directionally solidified under a constant positive thermal gradient in the melt. The gradient of constitutional supercooling was varied from almost zero (near the break-down of the planar liquid-solid interface at small growth speeds, cellular morphology) to near unity (large growth speeds, dendritic morphology). The spatial arrangements of cells and dendrites, as given by their coordination number, are not very different from each other. It appears that primary arm spacing maxima and the cell to dendrite transition are strongly influenced by the magnitude of the solute partition coefficient. The planar to cellular bifurction is supercritical in Pb-Sn which has a high partition coefficient, as compared to the subcritical behavior reported in Al-Cu and succinonitrile-acetone, both of which have low partition coefficients. The primary arm spacing model due to Hunt agrees with the experimentally observed trend for the whole growth regime. There is a good quantitative agreement at higher grdients of supercooling. However, the model overpredicts the primary arm spacings at low gradients of constitutional supercooling.

Chopra, M. A.↗
NASA NTRS1991

Basin-scale estimates of oceanic primary production by remote sensing - The North Atlantic

The monthly averaged CZCS data for 1979 are used to estimate annual primary production at ocean basin scales in the North Atlantic. The principal supplementary data used were 873 vertical profiles of chlorophyll and 248 sets of parameters derived from photosynthesis-light experiments. Four different procedures were tested for calculation of primary production. The spectral model with nonuniform biomass was considered as the benchmark for comparison against the other three models. The less complete models gave results that differed by as much as 50 percent from the benchmark. Vertically uniform models tended to underestimate primary production by about 20 percent compared to the nonuniform models. At horizontal scale, the differences between spectral and nonspectral models were negligible. The linear correlation between biomass and estimated production was poor outside the tropics, suggesting caution against the indiscriminate use of biomass as a proxy variable for primary production.

Platt, Trevor↗