Search NASA⌕ Search

SEARCH · Search NASA

Results for “reaction engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Experimental Investigation of Augmented Spark Ignition of a LO2/LCH4 Reaction Control Engine at Altitude Conditions

The use of nontoxic propellants in future exploration vehicles would enable safer, more cost-effective mission scenarios. One promising green alternative to existing hypergols is liquid methane (LCH4) with liquid oxygen (LO2). A 100 lbf LO2/LCH4 engine was developed under the NASA Propulsion and Cryogenic Advanced Development project and tested at the NASA Glenn Research Center Altitude Combustion Stand in a low pressure environment. High ignition energy is a perceived drawback of this propellant combination; so this ignition margin test program examined ignition performance versus delivered spark energy. Sensitivity of ignition to spark timing and repetition rate was also explored. Three different exciter units were used with the engine s augmented (torch) igniter. Captured waveforms indicated spark behavior in hot fire conditions was inconsistent compared to the well-behaved dry sparks. This suggests that rising pressure and flow rate increase spark impedance and may at some point compromise an exciter s ability to complete each spark. The reduced spark energies of such quenched deliveries resulted in more erratic ignitions, decreasing ignition probability. The timing of the sparks relative to the pressure/flow conditions also impacted the probability of ignition. Sparks occurring early in the flow could trigger ignition with energies as low as 1 to 6 mJ, though multiple, similarly timed sparks of 55 to 75 mJ were required for reliable ignition. Delayed spark application and reduced spark repetition rate both correlated with late and occasional failed ignitions. An optimum time interval for spark application and ignition therefore coincides with propellant introduction to the igniter.

Kleinhenz, Julie↗
DOE OSTI2023

Highly Oxidized Oxide Surface toward Optimum Oxygen Evolution Reaction by Termination Engineering

The oxygen evolution reaction (OER) is a critical step for sustainable fuel production through electrochemistry process. Maximizing active sites of nanocatalyst with enhanced intrinsic activity, especially the activation of lattice oxygen, is gradually recognized as the primary incentive. Since the surface reconfiguration to oxyhydroxide is unavoidable for oxygen-activated transition metal oxides, developing a surface termination like oxyhydroxide in oxides is highly desirable. In this work, we demonstrate an unusual surface termination of (111)-facet Co 3 O 4 nanosheet that is exclusively containing edge-sharing octahedral Co 3+ similar to CoOOH that can perform at approximately 40 times higher current density at 1.63 V (vs RHE) than commercial RuO 2 . It is found that this surface termination has an oxidized oxygen state in contrast to standard Co-O systems, which can serve as active site independently, breaking the scaling relationship limit. Finally, this work forwards the applications of oxide electrocatalysts in the energy conversion field by surface termination engineering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Catalytic Autoxidation for Depolymerization of Multilayer Plastic Films

Recycling multilayer plastic films is challenged by a diversity of polymers, prompting development of new recycling methods. For the depolymerization of mixed polymers like those in multilayer films, metal-catalyzed autoxidation offers a versatile chemical recycling method to deconstruct multiple polymers to useful oxygenates. Here, we demonstrate that catalytic autoxidation is effective for depolymerizing multilayer films across diverse chemistries. We investigated conditions for a model polyethylene substrate using a Co, Mn, and Br cocatalyst system, achieving full carbon closure with oxygenated small molecules contributing up to 48 mol% carbon. Subsequently, we characterized product distributions for several common polymers used in multilayer films using high-resolution mass spectrometry (HRMS) and developed analytical methods to quantify the resulting complex product streams. Optimized conditions for polyethylene were applied to 11 multilayer plastic films containing 10 different polymers, including films with nonpolymeric potential disrupters like aluminum foil and titanium dioxide, showing that catalytic autoxidation is effective across a broad range of polymer types and is resistant to disrupters and additives. The generation of CO 2 in these reactions overall suggests that both reaction engineering and modifications to the reaction conditions will be required to achieve higher yields of soluble oxygenated products.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Chemical engineering design of CO oxidation catalysts

How a chemical reaction engineer would approach the challenge of designing a CO oxidation catalyst for pulsed CO2 lasers is described. CO oxidation catalysts have a long history of application, of course, so it is instructive to first consider the special requirements of the laser application and then to compare them to the characteristics of existing processes which utilize CO oxidation catalysts. All CO2 laser applications require a CO oxidation catalyst with the following characteristics: (1) active at stoichiometric ratios of O2 and CO, (2) no inhibition by CO2 or other components of the laser environment, (3) releases no particulates during vibration or thermal cycling, and (4) long lifetime with a stable activity. In all applications, low consumption of power is desirable, a characteristic especially critical in aerospace applications and, thus, catalyst activity at low temperatures is highly desirable. High power lasers with high pulse repetition rates inherently require circulation of the gas mixture and this forced circulation is available for moving gas past the catalyst. Low repetition rate lasers, however, do not inherently require gas circulation, so a catalyst that did not require such circulation would be favorable from the standpoint of minimum power consumption. Lasers designed for atmospheric penetration of their infrared radiation utilize CO2 formed from rare isotopes of oxygen and this application has the additional constraint that normal abundance oxygen isotopes in the catalyst must not exchange with rare isotopes in the gas mixture.

Herz, Richard K.↗
DOE OSTI2023

2.3.4.104 - Lignin Conversion to Sustainable Aviation Fuel Blendstocks

The Lignin Conversion to Sustainable Aviation Fuel Blendstocks (LigSAF) project focuses on the conversion of lignin-rich streams to deoxygenated aromatic and cycloalkane blendstocks in the jet fuel range. This work is done in close collaboration with the BETO-funded Lignin-First Biorefinery Development project and industrial scale-up partners, and the work is closely guided by analysis to develop cost-effective and sustainable routes to produce lignin-based SAF blendstocks. To date, we have demonstrated the continuous catalytic conversion of a lignin oil from poplar to deoxygenated aromatic products at -85% C-mol yield. This hydrodeoxygenation process uses a stable, earth-abundant catalyst and requires no solvent. We have also established a baseline process model and associated techno-economic analysis and life cycle assessment that together demonstrate the potential to achieve cost parity with fossil carbon-based jet fuel at -70% reduction in greenhouse gas emissions. Current work is focused on expanding the slate of feedstocks for hydrodeoxygenation to include lignin oils from softwoods, agricultural residues, and grasses as well as from hydrolysis lignin substrates from biochemical conversion and pulp-and-paper processes. We are also undertaking catalyst development efforts to tune the reaction selectivity from aromatic compounds to cycloalkanes. Lastly, we are investigating reaction engineering strategies to slurry solids for hydrodeoxygenation reactions.

aromatics↗
DOE OSTI2026

Leadership at Interfaces: Capitalizing on the "Gaps" in Science, Technology and Education [Slides]

Leadership in the scientific enterprise is most commonly exemplified by those who commandeer major discoveries and critical breakthroughs that expand boundaries, naturally underpinning a competitive spirit among peers in the field. However, many other leadership opportunities exist at the interfaces of such boundaries - as well as at the interfaces of scientific disciplines, classes of professions and across generations - and may enable alternative guiding philosophies that are intrinsically less prone to competition and saturation, and perhaps appreciation. This presentation features a personal reflection of scientific and leadership philosophies that were intentionally manifested at, and by, irreplaceable interfaces of human creativity. Reaction engineering, an increasingly vanishing discipline within chemical engineering, is emphasized as a manifestation of interfacial leadership and serves as a vehicle to trace pivotal career moments in both the speaker's scientific discoveries and in his relational values within human enterprises.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Kinetics-Informed Neural Networks

Chemical kinetics and reaction engineering consists of the phenomenological framework for the disentanglement of reaction mechanisms, optimization of reaction performance and the rational design of chemical processes. Here, we utilize feed-forward artificial neural networks as basis functions to solve ordinary differential equations (ODEs) constrained by differential algebraic equations (DAEs) that describe microkinetic models (MKMs). We present an algebraic framework for the mathematical description and classification of reaction networks, types of elementary reaction, and chemical species. Under this framework, we demonstrate that the simultaneous training of neural nets and kinetic model parameters in a regularized multi-objective optimization setting leads to the solution of the inverse problem through the estimation of kinetic parameters from synthetic experimental data. We analyze a set of scenarios to establish the extent to which kinetic parameters can be retrieved from transient kinetic data, and assess the robustness of the methodology with respect to statistical noise. Furthermore, this approach to inverse kinetic ODEs can assist in the elucidation of reaction mechanisms based on transient data.

36 MATERIALS SCIENCE↗
NASA NTRS1998

Magellan Aerodynamic Characteristics During the Termination Experiment Including Thruster Plume-Free Stream Interaction

Results are presented on the aerodynamic characteristics of the Magellan spacecraft during the October 1994 Termination Experiment, including the effects of the thruster engine exhaust plumes upon the molecular free stream around the spacecraft and upon the aerodynamics coefficients. As Magellan passed through the Venusian atmosphere, the solar arrays were turned in opposite directions relative to the free stream creating a torque on the spacecraft. The spacecraft control system was programmed to counter the effects of this torque with attitude control engines to maintain an inertially fixed attitude. The orientation and reaction engine telemetry returned from Magellan are used to create a model of the aerodynamic torques. Geometric models of the Magellan spacecraft are analyzed with the aid of both free molecular and Direct Simulation Monte Carlo codes. The simulated aerodynamic torques determined are compared to the measured torques. The Direct Simulation Monte Carlo method is also used to model the attitude engine exhaust plumes, the free stream disturbance caused by these plumes, and the resulting torques acting on the spacecraft compared to no-exhaust plume cases. The effect of the exhaust plumes was found to be sufficiently large that thrust reversal is possible.

Cestero, Francisco J.↗
DOE OSTI2020

Nanocluster and single-atom catalysts for thermocatalytic conversion of CO and CO 2

In this Minireview, we discuss recent advances in understanding nanocluster and single-atom catalysts for CO and CO 2 emissions control applications. Through analyzing thermocatalytic CO oxidation and CO 2 reduction, two fundamentally and industrially important reactions, we compare representative nanocluster and single-atom catalytic systems from perspectives of intrinsic chemistry and reaction engineering. Generally, nanoclusters and single atoms display different catalytic performances (i.e., activity, selectivity, and stability) for these reactions depending on the synthesis methods, support materials, and reaction conditions. Key observations of activity and selectivity tradeoffs between nanoclusters and single-atom catalysts are highlighted. Here, the dynamic structural responses of these catalytic species under CO oxidation or CO 2 reduction reaction conditions are also discussed. Synthetic control and detailed experimental and computational characterization of single-atom and nanocluster catalysts for CO and CO 2 conversion have led to exciting progress over the past decade. Still, more efforts are needed to understand and develop catalysts that meet the environmental, energy, and technical requirements to power a sustainable global economy.

03 NATURAL GAS↗
NASA NTRS2015

Correlation of Amine Swingbed On-Orbit CO2 Performance with a Hardware Independent Predictive Model

The Amine Swingbed Payload is an experimental system deployed on the International Space Station (ISS) that includes a two-bed, vacuum regenerated, amine-based carbon dioxide (CO2) removal subsystem as the principal item under investigation. The aminebased subsystem, also described previously in various publications as CAMRAS 3, was originally designed, fabricated and tested by Hamilton Sundstrand Space Systems International, Inc. (HSSSI) and delivered to NASA in November 2008. The CAMRAS 3 unit was subsequently designed into a flight payload experiment in 2010 and 2011, with flight test integration activities accomplished on-orbit between January 2012 and March 2013. Payload activation was accomplished in May 2013 followed by a 1000 hour experimental period. The experimental nature of the Payload and the interaction with the dynamic ISS environment present unique scientific and engineering challenges, in particular to the verification and validation of the expected Payload CO2 removal performance. A modeling and simulation approach that incorporates principles of chemical reaction engineering has been developed for the amine-based system to predict the dynamic cabin CO2 partial pressure with given inputs of sorbent bed size, process air flow, operating temperature, half-cycle time, CO2 generation rate, cabin volume and the magnitude of vacuum available. Simulation runs using the model to predict ambient CO2 concentrations show good correlation to on-orbit performance measurements and ISS dynamic concentrations for the assumed operating conditions. The dynamic predictive modelling could benefit operational planning to help ensure ISS CO2 concentrations are maintained below prescribed limits and for the Orion vehicle to simulate various operating conditions, scenarios and transients.

Papale, William↗
NASA NTRS1993

Comprehensive investigation of HgCdTe metalorganic chemical vapor deposition

The principal objective of this experimental and theoretical research program was to explore the possibility of depositing high quality epitaxial CdTe and HgCdTe at very low pressures through metalorganic chemical vapor deposition (MOCVD). We explored two important aspects of this potential process: (1) the interaction of molecular flow transport and deposition in an MOCVD reactor with a commercial configuration, and (2) the kinetics of metal alkyl source gas adsorption, decomposition and desorption from the growing film surface using ultra high vacuum surface science reaction techniques. To explore the transport-reaction issue, we have developed a reaction engineering analysis of a multiple wafer-in-tube ultrahigh vacuum chemical vapor deposition (UHV/CVD) reactor which allows an estimate of wafer or substrate throughput for a reactor of fixed geometry and a given deposition chemistry with specified film thickness uniformity constraints. The model employs a description of ballistic transport and reaction based on the pseudo-steady approximation to the Boltzmann equation in the limit of pure molecular flow. The model representation takes the form of an integral equation for the flux of each reactant or intermediate species to the wafer surfaces. Expressions for the reactive sticking coefficients (RSC) for each species must be incorporated in the term which represents reemission from a wafer surface. The interactions of MOCVD precursors with Si and CdTe were investigated using temperature programmed desorption (TPD) in ultra high vacuum combined with Auger electron spectroscopy (AES). These studies revealed that diethyltellurium (DETe) and dimethylcadmium (DMCd) adsorb weakly on clean Si(100) and desorb upon heating without decomposing. These precursors adsorb both weakly and strongly on CdTe(111)A, with DMCd exhibiting the stronger interaction with the surface than DETe.

Raupp, Gregory B.↗
NASA NTRS1975

Estimating maximum instantaneous distortion from inlet total pressure rms and PSD measurements

An inexpensive method is developed to determine the extreme values of instantaneous inlet distortion. This method also provides insight into the basic mechanics of unsteady inlet flow and the associated engine reaction. The analysis is based on fundamental fluid dynamics and statistical methods to provide an understanding of the turbulent inlet flow and quantitatively relate the rms level and power spectral density (PSD) function of the measured time variant total pressure fluctuations to the strength and size of the low pressure regions. The most probable extreme value of the instantaneous distortion is then synthesized from this information in conjunction with the steady state distortion. Results of the analysis show the extreme values to be dependent upon the steady state distortion, the measured turbulence rms level and PSD function, the time on point, and the engine response characteristics. Analytical projections of instantaneous distortion are presented and compared with data obtained by a conventional, highly time correlated, 40 probe instantaneous pressure measurement system.

Melick, H. C., Jr.↗
NASA NTRS1983

Combustion performance and heat transfer characterization of LOX/hydrocarbon type propellants, volume 1

A program to evaluate liquid oxygen and various hydrocarbon fuel as low cost alternative propellants suitable for future space transportation system applications is discussed. The emphasis of the program is directed toward low earth orbit maneuvering engine and reaction control engine systems. The feasibility of regeneratively cooling an orbit maneuvering thruster was analytically determined over a range of operating conditions from 100 to 1000 psia chamber pressure and 1000 to 10,000-1bF thrust, and specific design points were analyzed in detail for propane, methane, RP-1, ammonia, and ethanol; similar design point studies were performed for a filmcooled reaction control thruster. Heat transfer characteristics of propate were experimentally evaluated in heated tube tests. Forced convection heat transfer coefficients were determined over the range of fluid conditions encompassed by 450 to 1800 psia, -250 to +250 F, and 50 to 150 ft/sec, with wall temperatures from ambient to 1200 F. Seventy-seven hot firing tests were conducted with LOX/propane and LOC/ethanol, for a total duration of nearly 1400 seconds, using both heat sink and water-cooled calorimetric chambers.

Michel, R. W.↗
NASA NTRS1983

Combustion performance and heat transfer characterization of LOX/hydrocarbon type propellants

An evaluation liquid oxygen (LOX) and various hydrocarbon fuels as low cost alternative propellants suitable for future space transportation system applications was done. The emphasis was directed toward low earth orbit maneuvering engine and reaction control engine systems. The feasibility of regeneratively cooling an orbit maneuvering thruster was analytically determined over a range of operating conditions from 100 to 1000 psia chamber pressure and 1000 to 10,000-1bF thrust, and specific design points were analyzed in detail for propane, methane, RP-1, ammonia, and ethanol; similar design point studies were performed for a film-cooled reaction control thruster. Heat transfer characteristics of propane were experimentally evaluated in heated tube tests. Forced convection heat transfer coefficients were determined. Seventy-seven hot firing tests were conducted with LOX/propane and LOX/ethanol, for a total duration of nearly 1400 seconds, using both heat sink and water-cooled calorimetric chambers. Combustion performance and stability and gas-side heat transfer characteristics were evaluated.

Michel, R. W.↗
DOE OSTI2023

Reaction‐induced morphology control in block copolymers

Abstract Controlling the self‐assembly behaviors of block copolymers (BCPs) is a focal point of many research thrusts due to their broad use in various applications. While BCP molecular weight, volume fraction, and chemical identities are key thermodynamic parameters to determine their morphology, an emergent method in this area is through reaction‐induced changes to the characteristics of a BCP in situ , which provides access to multiple morphologies and domain sizes from a single parent polymer, as well as enabling the formation of metastable morphologies which may be difficult to attain otherwise. This work provides a focused review about the current state of reaction‐induced morphology control in BCPs in both solution and solid states. Furthermore, we provide a forward‐looking perspective on the future opportunities of understanding and employing reaction engineering to manipulate and advance BCP self‐assembly. © 2023 Society of Industrial Chemistry.

Robertson, Mark↗