Search NASA⌕ Search

SEARCH · Search NASA

Results for “recrystallization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Quasi in-situ analysis of geometrically necessary dislocation density in α-fibre and γ-fibre during static recrystallization in cold-rolled low-carbon Ti-V bearing microalloyed steel

Highlights: • Average GND density is higher in gamma fibre than alpha fibre. • Higher drop in average GND density in un-recrystallized portion of gamma fibre • Fine precipitates pin the grain boundary at 700 °C 0 s. • Precipitates are coarse at 800 °C and present inside strain-free grains. - Abstract: In the present study, cold-rolled low-carbon steel is annealed at three different conditions: 700 °C for 0 s, 800 °C for 0 s and 800 °C for 2 min at the heating rate of ~10 °C/s. Recrystallization behaviour on sample surface is studied using a heated stage Scanning Electron Microscopy and Electron Backscattered Diffraction. For the lower annealing temperature of 700 °C with no dwell, almost no recrystallization is observed and microstructure resembles the as-received deformed material with the exception of occasional sub-micron sized nuclei. For the annealing conditions of 800 °C 0 s and 800 °C 2 min, onset and evolution of recrystallization is observed in-situ as a function of the initial as-cold rolled texture. Slower recovery rate of alpha fibre than gamma fibre is observed and confirmed by lower drop in average geometrically necessary dislocation (GND) density for un-recrystallized alpha fibres (1.1E+14 m{sup −2} for 700 °C 0 s, 1.4E+14 m{sup −2} for 800 °C 0 s and 4.5E+14 m{sup −2} for 800 °C 2 min) than for un-recrystallized gamma fibre grains (3.0E+14 m{sup −2} for 700 °C 0 s, 6.2E+14 m{sup −2} for 800 °C 0 s and 9.8E+14 m{sup −2} for 800 °C 2 min) during annealing. Strong gamma texture in recrystallized matrix is found for annealing conditions of 800 °C 0 s and 800 °C 2 min. From TEM characterisation it was shown that sub-grain boundaries are decorated with fine precipitates (diameter d < 15 nm) of titanium‑vanadium carbides (Ti,V)C for the annealing condition of 700 °C 0 s, which suggests that these precipitates play a major overall role in retardation of the recrystallization kinetics.

36 MATERIALS SCIENCE↗

Free surface effects on the recrystallization of compressed, stable, Al-Mn single crystals

Highlights: • The free surface provokes high frequency nucleation. • The free surface and surface ‘quality’ do not modify the orientations of the recrystallized grains. • The misorientation relations across recrystallization front are similar for all sections of both orientations. The free surface effect on the grain crystallography and morphology during recrystallization has been studied in stable Goss {110}001 and brass {110}112 - oriented single crystals of Al-1%wt.Mn alloy. The samples were plane strain compressed up to a strain of about 0.5 to develop a homogeneous structure comprising two sets of symmetrical microbands and then lightly annealed. The variation of recrystallization after annealing was then analysed by optical microscopy and SEM/EBSD on different cross-sections. The results are discussed in terms of the misorientation angle and axis distributions. The free surface provokes high frequency nucleation leading to a small grain size compared to internal sections of the bulk sample. However, the free surface and surface ‘quality’ do not modify the orientations of the recrystallized grains, i.e. similar groups of recrystallized grain orientations were observed for all sections. This leads to a strong misorientation relation between deformed/recovered area orientations and the limited number of groups of recrystallized grain orientations, basically the same as those observed during bulk recrystallization of similar crystals.

36 MATERIALS SCIENCE↗

Role of Precipitates in Recrystallization Mechanisms of Nb-Mo Microalloyed Steel

Recrystallization behavior of a Nb-Mo microalloyed steel has been investigated using double-hit compression tests. A suitable reheating temperature and soaking time were established for the complete dissolution of the microalloying precipitates prior to hot deformation. The influence of hot deformation conditions on the flow behavior and the effect of alloying elements, Nb in particular, on austenite recrystallization kinetics are highlighted. The strain-induced precipitation has been found to play an important role in hindering recrystallization kinetics. Post-deformation microstructural analysis indicates that strain-induced grain boundary migration (SIMB) is one of the mechanisms for the formation of recrystallized grains. Retardation of recrystallization has been explained by estimating pinning force of Nb(C, N) precipitates and recrystallization driving force at 1000 °C, which is in good agreement with the experimental observations in the present study as well as other reported data. The study brings out a better understanding on the influence of strain-induced precipitates on recrystallization behavior.

36 MATERIALS SCIENCE↗

Study of Static Recrystallization Behavior of a Mg-6Al-3Sn Alloy

In this study, the static recrystallization behavior of cold-rolled Mg-6Al-3Sn alloy has been studied during annealing in the temperature range of 200-400 °C. The role of Mg{sub 17}Al{sub 12} precipitation during recrystallization is discerned. A significant drop in the grain size has been reported post-recrystallization. The results suggest that the recrystallization predominately started at the prior grain boundaries and within the twin boundaries. Recrystallization at lower temperatures was found to be incomplete despite holding for a longer duration. However, at higher temperatures, the recrystallization was observed to be complete in shorter times. The role of concurrent precipitation during recrystallization has been ascertained.

36 MATERIALS SCIENCE↗

Modelling recrystallization textures driven by intragranular fluctuations implemented in the viscoplastic self-consistent formulation

This work presents a recrystallization model driven by intragranular orientation gradients and strain energy fields calculated by means of the viscoplastic self-consistent (VPSC) formulation. The VPSC model is extended for calculation of the coupling between intragranular stress fluctuations with corresponding second moments of lattice spin and misorientation fields in the grains. Access to these quantities allows modelling of transition bands and nucleation kinetics. In the proposed recrystallization model, grain growth is assumed to be proportional to the difference between the stored energy of each grain and that of the effective medium. Recrystallization textures for several cubic metals are simulated, showing good agreement with corresponding experiments. The model reveals the importance of considering appropriate, microstructurally-based and orientation-dependent recrystallization nucleation mechanisms. The recrystallization texture of heavily rolled copper with a strong cube texture component is found to be a consequence of nucleation at transition bands, which is also the cause of the recrystallization textures in compressed iron and drawn copper wire. Finally, in contrast, the recrystallization texture of rolled interstitial-free steel is found to be caused by grain boundary nucleation occurring in grains with the highest strain energy.

36 MATERIALS SCIENCE↗

Impact of the plastic deformation microstructure in metals on the kinetics of recrystallization: A phase-field study

The sensitivity of recrystallization kinetics in metals to the heterogeneity of microstructure and deformation history is a widely accepted experimental fact. However, most of the available recrystallization models employ either a mean field approach or use grain-averaged parameters, and thus neglecting the mesoscopic heterogeneity induced by prior deformation. Here in the present study, we investigate the impact of deformation-induced dislocation (subgrain) structure on the kinetics of recrystallization in metals using the phase-field approach. The primary focus here is upon the role of dislocation cell boundaries. The free energy formulation of the phase-field model accounts for the heterogeneity of the microstructure by assigning localized energy to the resulting dislocation microstructure realizations generated from experimental data. These microstructure realizations are created using the universal scaling laws for the spacing and the misorientation angles of both the geometrically necessary and incidental dislocation boundaries. The resulting free energy is used into an Allen-Cahn based model of recrystallization kinetics, which are solved using the finite element method. The solutions thus obtained shed light on the critical role of the spatial heterogeneity of deformation in the non-smooth growth of recrystallization nuclei and on the final grain structure. The results showed that, in agreement with experiment, the morphology of recrystallization front exhibits protrusions and retrusions. By resolving the subgrain structure, the presented algorithm paves the way for developing predictive kinetic models that fully account for the deformed state of recrystallizing metals.

36 MATERIALS SCIENCE↗

Mesoscale model for fission-induced recrystallization in U-7Mo alloy

A mesoscale model is developed by integrating the rate theory and phase-field models and is used to study the fission-induced recrystallization in U-7Mo alloy. The rate theory model is used to predict the dislocation density and the recrystallization nuclei density due to irradiation. The predicted fission rate and temperature dependences of the dislocation density are in good agreement with experimental measurements. This information is used as input for the multiphase phase-field model to investigate the fission-induced recrystallization kinetics. The simulated recrystallization volume fraction and bubble induced swelling agree well with experimental data. The effects of the fission rate, initial grain size, and grain morphology on the recrystallization kinetics are discussed based on an analysis of recrystallization growth rate using the modified Avrami equation. Here, we conclude that the initial microstructure of the U-Mo fuels, especially the grain size, can be used to effectively control the rate of fission-induced recrystallization and therefore swelling.

36 MATERIALS SCIENCE↗

Recrystallization behavior of a supersaturated Al Mn alloy

The effect of concurrent precipitation on recrystallization behavior during the isothermal annealing of a supersaturated and deformed Al-Mn alloy was investigated. It is found that concurrent precipitation strongly affects the recrystallization behavior of this alloy. At low temperatures, concurrent precipitation retards recrystallization and results in large flat grains. The size of recrystallized grains decreases significantly with increasing temperature. The kinetics of recrystallization was determined by measurements of hardness. The JMAK exponent decreases from 3.0 to 0.8 as the annealing temperature increases from 371 C to 427 C. The activation energy for recrystallization of the alloy is about 456 kJ/mol. Concurrent precipitation enhances the activation energy for recrystallization of aluminum alloys.

36 MATERIALS SCIENCE↗

CHARACTERIZING AND CONTROLLING RECOVERY AND RECRYSTALLIZATION IN NIOBIUM FOR IMPROVED SRF CAVITY PERFORMANCE

Crystal defects, such as dislocations and low-angle boundaries, provide sources of magnetic flux trapping in the Nb materials used for superconducting radio frequency (SRF) resonating cavities. Improving the performance of SRF cavities, as measured through the quality factor, requires reducing these defects. SRF cavity production involves deformation processing, such as rolling and forming, and strategic annealing heat treatments. The resulting microstructures can be recovered, recrystallized, or both. Because recovery leaves many defects that can trap flux, recrystallization should improve cavity performance. Thus, processing schedules that produce complete recrystallization without excessive grain growth need to be designed. Solutions to this problem require understanding physical metallurgy and differentiating between recovered and recrystallized regions of microstructure. Backscattered electron microscopy techniques are applied to this end. We demonstrate that the conditions required to produce fully recrystallized microstructures depend on Nb impurity content, suggesting that processing schedules may need to be adjusted by material heat or lot. We also demonstrate that processing can be used to control growth of recrystallized grains to maintain mechanical strength in fully recrystallized materials. Forming cavities from cold-rolled Nb sheet material may provide strategic new routes to obtain microstructures that improve SRF cavity performance.

Taleff, E. [The University of Texas at Austin]↗

Recrystallization and Grain Growth Simulations for Multiple-Pass Rolling and Annealing of U-10Mo

A simulation model of recrystallization and grain growth has been developed to investigate grain structure evolution during deformation and heat treatment in polycrystalline U-10wt% Mo (U-10Mo) fuel. Experimentally obtained U-10Mo microstructures were used as input for closed loop simulations of multiple rolling, intermediate heating and final annealing process. FEM calculations of deformation and Potts Model simulations of recrystallization and grain growth were used to iteratively inform each subsequent stage of simulation. Furthermore, the model was then applied to predict the grain structure evolution during multiple-pass hot rolling of U-10Mo, and benchmarked against experimentally observed U-10Mo recrystallization behavior. The results showed that our model was able to capture the coupling between deformation and recrystallization as a function of microstructure, including particle stimulated nucleation and recrystallization nucleation on grain boundaries. Additionally, we have achieved reasonable quantitative agreement with U-10Mo recrystallization and grain growth behavior.

36 MATERIALS SCIENCE↗

High temperature microstructural stability and recrystallization mechanisms in 14YWT alloys

In-situ neutron diffraction experiments were performed on room temperature compressed 14YWT nanostructured ferritic alloys at 1100°C and 1150°C to understand their thermally activated static recrystallization mechanisms. The existence of high density of Y-Ti-O rich nano-oxides (<5 nm) shift the recrystallization temperature up due to Zener pinning of the grain boundaries, making these materials attractive for high temperature applications. This study serves to quantify the texture evolution in-situ and understand the effect of particles on the recrystallization mechanisms in 14YWT alloys. We have shown, both experimentally and theoretically, that there is considerable recovery in the 20% compressed sample after 6.5 h annealing at 1100°C while recrystallization occurs within an hour of annealing at 1100°C and 1150°C in the 60% compressed samples. Moreover, the 60% compressed samples show {112}<110> and {112}<111> texture components during annealing, in contrast to the conventional recrystallization textures in body centered cubic alloys. Furthermore, nano-oxide size, shape, density and distribution are considerably different in unrecrystallized and abnormally grown grains. Transmission electron microscopy analysis shows that oxide particles having a size between 5 and 30 nm play a critical role for recrystallization mechanisms in 14YWT nanostructured ferritic alloys.

36 MATERIALS SCIENCE↗

Effect of grain structure and strain rate on dynamic recrystallization and deformation behavior: A phase field-crystal plasticity model

Herein, a phase field (PF)-crystal plasticity (CP) model has been developed to study the effects of initial grain structures, recrystallized grain orientation, and strain rates on dynamic recrystallization and deformation behavior under stress states typical of the Shear Assisted Processing and Extrusion (ShAPE) process. The model takes the geometrically necessary dislocation density as the nucleation criterion for recrystallization and minimizes the deformation energy as the driving force of recrystallized grain growth. Using this model, the effects of grain orientations and strain rates on dynamic recrystallization and deformation behavior were simulated. The results demonstrate that (1) a polycrystalline structure with the texture observed in ShAPE process has the lowest yield stress under the ShAPE stress conditions, (2) the recrystallized grains with the texture observed in ShAPE process largely soften the materials, and (3) higher shear strain rate or rotation speed results in larger magnitude of material softening.

36 MATERIALS SCIENCE↗

Recrystallization of Cu-poor CuInS{sub 2} assisted by metallic Cu or Ag

We monitor the recrystallization of Cu-poor CuInS{sub 2} thin films assisted by pure Cu or pure Ag by means of real-time synchrotron-based polychromatic X-ray diffraction. In both cases a new microstructure is formed accompanied by an increase in grain size. In the case of Cu, the onset temperature of the thin-film recrystallization is higher than 370 deg. C. In the case of Ag, the thin-film recrystallization comes to an end at 270 deg. C. The Ag-assisted recrystallization occurs in the presence of the body-centered cubic beta-Ag{sub 2}S phase. We find that domain growth and diffusion of silver into the film occur simultaneously. - Graphical abstract Keywords: Recrystallization; Thin-film solar cells; Energy-dispersive x-ray diffraction: In-situ monitoring by means of energy-dispersive X-ray diffraction of the thin-film recrystallization of Cu-poor CuInS{sub 2} assisted by metallic Ag.

36 MATERIALS SCIENCE↗

Effects of V addition on recrystallization resistance of 7150 aluminum alloy after simulative hot deformation

The effects of different V contents (0.01 to 0.19 wt.%) on the recrystallization resistance of 7150 aluminum alloys during post-deformation heat treatment were investigated. The microstructural evolutions at as-cast, as-homogenized conditions and after post-deformation annealing were studied using optical, scanning electron and transmission electron microscopes and using the electron backscattered diffraction technique. The precipitation of Al{sub 21}V{sub 2} dispersoids was observed in alloys containing 0.11 to 0.19 wt.% V after homogenization. The dispersoids were mainly distributed in the dendrite cells, and the precipitate-free zones occurred in the interdendritic regions and near grain boundaries. V addition could significantly enhance the recrystallization resistance during post-deformation annealing, particularly in the presence of a great number of Al{sub 21}V{sub 2} dispersoids. Recrystallized grain growth was effectively restricted because of the dispersoid pinning effect. The alloy containing 0.15 wt.% V exhibited the highest recrystallization resistance amongst all V-containing alloys studied. - Highlights: • Investigated the effect of V level on microstructure and flow stress of 7150 alloys • Characterized microstructures using optical microscopy, SEM, TEM and EBSD • Described the precipitation behavior of V-dispersoids in the dendritic structure • Studied the V effect on recrystallization resistance during post heat treatment • V addition greatly enhanced the recrystallization resistance during annealing.

36 MATERIALS SCIENCE↗

Effect of strain on evolution of dynamic recrystallization in Nb-1 wt%Zr-0.1 wt%C alloy at 1500 and 1600 °C

Uniaxial compression tests were carried out on Nb-1 wt%Zr-0.1 wt%C alloy at temperature of 1500 and 1600 °C and strain rate of 0.1 s{sup −1} to study the evolution of dynamic recrystallization with strain. Electron back scatter diffraction was used to quantify the microstructural evolution. Nb-1Zr-0.1C alloy showed a necklace structure at a strain of 0.9 when deformed at 1500 °C and at strain of 0.6 when deformed at 1600 °C, both at strain rate of 0.1 s{sup −1}. This suggested the occurrence of dynamic recrystallization. At 1500 °C and strain of 0.9 the local average misorientation and the grain orientation spread was low confirming the presence of dynamic recrystallization at this deformation condition. At both 1500 and 1600 °C and all measured strains the recrystallized grains had a strong fiber component of <001>. - Highlights: • Necklace formation of dynamically recrystallized grains occurred at strain of 0.6 and 0.9 for 1500 and 1600 °C, respectively. • Equiaxed microstructures were seen with increase in strain for both 1500 and 1600 °C. • At large strains the predominant recrystallized texture evolved to <001> pole.

36 MATERIALS SCIENCE↗

Local residual stresses and microstructure within recrystallizing grains in iron

The intragranular strains and the microstructure within recrystallizing grains in single phase pure iron have been systematically studied in 3D using synchrotron micro-diffraction. In contradiction to common knowledge we observe that residual elastic strains of up to 1–2 × 10 –3 are present in the recrystallizing grains. The local strain variations within individual grains can be similar in magnitude to those between different grains. The effects of processing parameters, including rolling reduction, recrystallized volume fraction, and cooling rate, as well as microstructural parameters, including grain size, orientation and internal misorientation, on the development of local residual elastic strains and microstructure have been quantified. It is suggested that the difference in local defect density between recrystallized grains and the surrounding deformed matrix, as well as the redistribution of medium to long-range residual stresses in the deformed grains, are the main reasons for the development of such strains in the recrystallized grains. The local residual stress levels are calculated and their possible impact on the mechanical properties and recrystallization processes are discussed.

36 MATERIALS SCIENCE↗

A Quantitative Analysis of Room Temperature Recrystallization Kinetics in Electroplated Copper Films using High Resolution X-ray Diffraction

Time-resolved in situ x-ray diffraction measurements were used to study the room-temperature recrystallization kinetics of electroplated copper thin films with thicknesses between 400 and 1000 nm. The thinnest films exhibited limited recrystallization and subsequent growth of grains, while recrystallized grains in the thicker films grew until all as-plated microstructure was consumed. For all films, recrystallized grains that belonged to the majority texture component, <111>, started growing after the shortest incubation time. These grains exhibited volumetric growth until they achieved the film thickness. After this point the growth mode became planar, with the <111>-type grains growing in the plane of the film. Grains with the <111> direction normal to the film surface started growing after the <111>-type grains switched to planar growth. However, the planar growth of this texture component finished at the same time as the growth of the <111> grains. Profile fitting of the 111 peak permitted the separation of the diffraction signals from recrystallized and as-plated grain populations. The average strains in these two populations, calculated from the peak position of the corresponding {l_brace}111{r_brace} reflections, were different, indicating a heterogeneous stress state within this texture component. The increasing volume fraction of recrystallized <111> grains with time was monitored via the variation in the diffracted intensity. This variation could be represented by the Johnson-Mehl-Avrami-Kolmogorov model.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Multiscale Model for Simulating Fission-Induced Recrystallization in U-Mo Alloy

U-Mo alloy is one of the most promising fuels for the future high performance research and test reactors due to its high uranium loading density and stable irradiation behavior. However, a major concern to its qualification is the fuel swelling at high fission density due to the formation of large fission-gas bubbles. The fission-induced recrystallization further expedites the formation and growth of gas bubbles. So far, the exact mechanism of recrystallization is still unclear. One possible driving force for recrystallization is the production of point defects and interstitial loops due to irradiation. Following this, we developed a multi-scale model by integrating the rate-theory and phase-field models to study microstructural evolutions in irradiated U-Mo alloy, i.e., fission-induced gas bubble evolution and recrystallization. Density function theory (DFT) calculations are utilized to predict the defect formation energies, diffusivities of defects, the interfacial energy of gas bubble, and the elastic constants of U-Mo alloy, etc. The dislocation density evolution is predicted by the rate-theory developed by Jeff. The grain subdivision occurs once the dislocation density is above a critical value. The grain growth coupled with gas bubbles evolution is modeled using a multi-phase phase-field model. The effects of fission rate and initial grain microstructure on the recrystallization process are systematically investigated. The simulated dislocation density, sub-grain size distribution, and volume fraction of the recrystallization grains under different fission density are comparable with experimental data. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗