Search NASA⌕ Search

SEARCH · Search NASA

Results for “rotor angle stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Correlating measured and predicted inplane stability characteristics for an advanced bearingless rotor

The experimental data were obtained from hover tests for a scaled model of an advanced bearingless main rotor. Both isolated rotor and ground resonance conditions were tested. Test parameters included blade built-in cone and sweep angles, rotor inplane structural damping, pitch link location and fuselage structural damping. Analytical results for the conditions tested were obtained using current Bell Helicopter analyses. In addition, variations in the analytical models were made to assess their impact on the correlation between computed and measured results. Results are presented in tabular and graphical form.

Weller, W. H.↗
NASA NTRS1983

Acoustic measurements of the X-wing rotor

Noise measurements of a stoppable X-wing rotor system model, tested in the Ames 40- by 80-foot wind tunnel, are summarized. Performance, control system stability, and noise of the model were investigated at various forward speeds, tip speeds, collective blade angles, jet blowing velocities, and model attack angles. The model was tested in the rotating wing helicopter configuration, in the fixed wing configuration, and in wing configurations between the two. Noise data obtained in the helicopter configuration at the two highest tip speeds (Mach 0.44 and 0.47) and at wind tunnel speeds below 140 knots are reported. Test configuration and performance information are included. General acoustic measurements (dB, dBA, and PNdB) at six microphone locations are presented for all conditions under which the background noise was below the model noise. More specific measurements (1/3-octave and blade passage frequency harmonic levels) are presented for selected conditions. Graphs of dBA and 1/3-octave spectra, which show the noise trends as functions of operating condition, are included. The noise depends mainly on the jet blowing velocity. The noise levels were highest at moderate jet blowing velocities, less at the highest velocity, and lowest with no blowing at all.

Mosher, M.↗
NASA NTRS1972

A Theoretical and Experimental Investigation of Flap-Lag Stability of Hingeless Helicopter Rotor Blades

The stability of hingeless rotor blade oscillations in hover is examined theoretically using a simplified centrally-hinged, spring-restrained, rigid blade to approximate the deflections of actual elastic blades. The aerodynamic and inertial coupling between the flap and lead-lag degrees of freedom is primarily responsible for instability, however elastic coupling and kinematic pitch-lag coupling both exert a powerful influence on hingeless rotor blade stability. Experimental results obtained from a two-bladed 1.81m diameter model rotor designed for minimum elastic coupling have confirmed the results of linear theory. For this model configuration rotor blade stall at high pitch angles was found to counteract the destabilizing flap-lag coupling and increase the damping of lead-lag oscillations. It was possible to account for this effect with the theory by using drag data for stalled airfoils.

Ormiston, R. A.↗
NASA NTRS1989

A study of fundamental issues in higher harmonic control using aeroelastic simulation

This paper describes a higher harmonic control (HHC) study of a four-bladed helicopter rotor using a coupled flap-lag-torsional aeroelastic stability and response analysis which incorporates finite-state, time-domain aerodyamics. The rotor trim condition is determined using a simplified flap-lag-torsional aeroelastic analysis. Deterministic and cautious controllers based on local and global HHC models are implemented to reduce 4/rev hub loads on roughly equivalent articulate and hingeless rotors. Results obtained for the case when the objective function requires reduction of hub shears alone are compared with results obtained when hub shears and moments are reduced simultaneously. The effects of HHC on blade aeroelastic stability are also considered. Finally, the power requirements for implementing HHC on a hingeless rotor are compared with those obtained for an articulated rotor. It is concluded that hingeless rotors require considerably more power and higher control angles than comparable articulated rotors.

Robinson, Lawson H.↗
NASA NTRS1974

Nonlinear equations of motion for the elastic bending and torsion of twisted nonuniform rotor blades

The equations of motion are developed by two complementary methods, Hamilton's principle and the Newtonian method. The resulting equations are valid to second order for long, straight, slender, homogeneous, isotropic beams undergoing moderate displacements. The ordering scheme is based on the restriction that squares of the bending slopes, the torsion deformation, and the chord/radius and thickness/radius ratios are negligible with respect to unity. All remaining nonlinear terms are retained. The equations are valid for beams with mass centroid axis and area centroid (tension) axis offsets from the elastic axis, nonuniform mass and stiffness section properties, variable pretwist, and a small precone angle. The strain-displacement relations are developed from an exact transformation between the deformed and undeformed coordinate systems. These nonlinear relations form an important contribution to the final equations. Several nonlinear structural and inertial terms in the final equations are identified that can substantially influence the aeroelastic stability and response of hingeless helicopter rotor blades.

Hodges, D. H.↗
NASA NTRS1945

Wind-Tunnel Tests of a Portion of a PV-2 Helicopter Rotor Blade

A portion of a PV-2 helicopter rotor blade has been tested in the 6- by 6-foot test section of the Langley stability tunnel to determine if the aerodynamic characteristics were seriously affected by cross flow or fabric distortion. The outer portion of the blade was tested as a reflection plane model pivoted about the tunnel wall to obtain various angles of cross flow over the blade. Because the tunnel wall acts as a plane of sy~try, the measured aerodynamic characteristics correspond to those of an airfoil having various angles of sweepforward and sweepback. Tests were made with the vents on the lower surface open and also with the vents sealed and the internal pressure held at -20 inches of water producing an internal pressure coefficient of -1.059. The change in contour resulting from the range of internal pressures used had very little effect on the aerodynamic characteristics of the blade. The test methods were considered to simulate inadequately the flow conditions over the rotor blade because the effects of cross flow were limited to conditions corresponding to sweep of the blade. The results indicated that this type of cross flow had only minor effects on the aerodynamic characteristics of the blade. It is believed, therefore, that future tests to determine the effects on the aerodynamic characteristics of cross flow should utilize complete rotors.

Kemp, William B., Jr.↗
NASA NTRS1973

Concepts for a theoretical and experimental study of lifting rotor random loads and vibrations (the effects of some rotor feedback systems on rotor-body dynamics), Phase 7-A

The effects of three gyroless rotor feedback systems: (1) coning feedback, (2) proportional tilting feedback, and (3) a combination of these on the rotor-body dynamics of hingeless rotorcraft are studied with a simplified analytical model in the advance ratio range from 0 to .8. Combinations of feedback phase angles and control phase angles are selected to minimize control cross coupling and control sensitivity changes between low and high speed flight. For the feedback systems thus selected the effects of feedback gain and control actuator time lag on the stability both with fixed hub and in free flight is studied, whereby the rotorcraft is free in pitch, roll and vertical motion but otherwise restrained. For the free flight is studied, whereby the rotorcraft is free in pitch, roll and vertical motion but otherwise restrained. For the free flight conditions the effects of a horizontal tail are also determined in itself and in combination with the rotor feedback systems.

Hohenemser, K. H.↗
NASA NTRS1962

Use of an Inertia Sphere to Damp the Angular Motions of Spinning Space Vehicles

A theoretical study was made of a device which might be used to damp the angular motions of spin-stabilized space vehicles with constant moments of inertia. the device was assumed to consist of a rate gyro, a servo control, and a rotor mounted in a single gimbal. The investigation was conducted by considering the general equations of motion of the vehicle-damper system and noting that simplification would result if the damper had a spherical inertia distribution. Such a distribution was assumed thereafter, and a control command was defined so that the gimbal angle would be proportional to the angular velocity of the vehicle about the gimbal axis. The resulting equations were linearized, and the Routh-Hurwitz criterion was applied to determine the conditions for stability. The study included two numerical examples showing possible application of inertia-sphere rate dampers. The general conditions for stability were found to be feasible for practical applications. A simplified stability criterion covers a large class of practical problems.

SPHERE↗
NASA NTRS1989

Calculation of the rotor induced download on airfoils

Interactions between the rotors and wing of a rotary wing aircraft in hover have a significant detrimental effect on its payload performance. The reduction of payload results from the wake of lifting rotors impinging on the wing, which is at 90 deg angle of attack in hover. This vertical drag, often referred as download, can be as large as 15 percent of the total rotor thrust in hover. The rotor wake is a three-dimensional, unsteady flow with concentrated tip vortices. With the rotor tip vortices impinging on the upper surface of the wing, the flow over the wing is not only three-dimensional and unsteady, but also separated from the leading and trailing edges. A simplified two-dimensional model was developed to demonstrate the stability of the methodology. The flow model combines a panel method to represent the rotor and the wing, and a vortex method to track the wing wake. A parametric study of the download on a 20 percent thick elliptical airfoil below a rotor disk of uniform inflow was performed. Comparisons with experimental data are made where the data are available. This approach is now being extended to three-dimensional flows. Preliminary results on a wing at 90 deg angle of attack in free stream is presented.

Lee, C. S.↗
NASA NTRS1981

Dynamics of an experimental two bladed horizontal axis wind turbine with blade cyclic pitch variation

The turbine under study incorporates the combination of two features: the application of blade cyclic pitch variation; and the use of yaw angle control for rotor speed and torque regulation. Due to its emasculation by passive cyclic pitch variation the rotor can be rapidly yawed without encountering gyroscopic and aerodynamic hub moments and without noticeable out of plane excursions. The two bladed upwind rotor is vane stabilized and of very simple and rugged design. The principle was first checked out with a small scale wind tunnel model and then tested in the atmosphere with a 7.6 meter diameter experimental fully instrumented wind turbine driving a 3 phase alternator. The test results are summarized with respect to structural dynamics and yaw dynamics.

Hotenemser, K. H.↗
NASA NTRS1985

Parametric study of the aeroelastic stability of a bearingless rotor

A trade study was conducted to illustrate the sensitivity of the aeroelastic stability of a bearingless main rotor to the rotor hub coupling parameters that are available for the designer. The results are presented over the complete range of rotor speed and collective pitch available and the effects on air resonance of the 6 beam installation angles are compared together with the results of offsetting the cuff snubber attachment. The major part of the study was conducted using the FLAIR analysis which incorporates a uniform representation of the flexbeam. Results are also shown for a modified version of FLAIR in which the uniform beam is replaced by a member having the geometric tailoring resulting from structural optimization.

Hooper, W. E.↗
NASA NTRS1977

Effect of rotor wake on aerodynamic characteristics of a 1/6 scale model of the rotor systems research aircraft

Tests were conducted in the Langley V/STOL tunnel to determine the effect of the main-rotor wake on the aerodynamic characteristics of the rotor systems research aircraft. A 1/6-scale model with a 4-blade articulated rotor was used to determine the effect of the rotor wake for the compound configuration. Data were obtained over a range of angles of attack, angles of sideslip, auxiliary engine thrusts, rotor collective pitch angles, and rotor tip-path plane angles for several main-rotor advance ratios. Separate results are presented for the forces and moments on the airframe, the wing, and the tail. An analysis of the test data indicates significant changes in the aerodynamic characteristics. The rotor wake increases the longitudinal static stability, the effective dihedral, and the lateral static stability of the airframe. The rotor induces a downwash on the wing. This downwash decreases the wing lift and increases the drag. The asymmetrical rotor wake induces a differential lift across the wing and a subsequent rolling moment. These rotor induced effects on the wing become smaller with increasing forward speed.

Mineck, R. E.↗
NASA NTRS1982

A mathematical model of a single main rotor helicopter for piloted simulation

A mathematical model, suitable for piloted simulation of the flying qualities of helicopters, is a nonlinear, total force and moment model of a single main rotor helicopter. The model has ten degrees of freedom: six rigid body, three rotor flapping, and the rotor rotational degrees of freedom. The rotor model assumes rigid blades with rotor forces and moments radially integrated and summed about the azimuth. The fuselage aerodynamic model uses a detailed representation over a nominal angle of attack and sideslip range of + or - 15 deg., as well as a simplified curve fit at large angles of attack or sideslip. Stabilizing surface aerodynamics are modeled with a lift curve slope between stall limits and a general curve fit for large angles of attack. A generalized stability and control augmentation system is described. Additional computer subroutines provide options for a simplified engine/governor model, atmospheric turbulence, and a linearized six degree of freedom dynamic model for stability and control analysis.

Talbot, P. D.↗
NASA NTRS1986

Analysis of rotordynamic coefficients of helically-grooved turbulent annular seals

An analysis for helically-grooved turbulent annular seals is developed to predict leakage and dynamic coefficients, as related to rotordynamics. The grooved surface pattern is formulated as an inhomogeneous directivity in surface shear stress. The zeroth-order equations define the steady-state leakage and the circumferential velocity development due to wall shear for a centered rotor position. The first-order equations define perturbations in the pressure and axial and circumferential velocity fields due to small motion of the rotor about the centered position. Numerical results are presented for proposed grooved seals in the High Pressure Oxygen Turbopump (HPTOP) of the Space Shuttle Main Engine (SSME) and for a water-pump application. The results show that an optimum helix angle exists from a rotordynamic stability viewpoint. Further, a properly designed helically-grooved stator is predicted to have pronounced stability advantages over other currently used seals.

Kim, C.-H.↗
NASA NTRS1977

Aerodynamic characteristics of a 1/6-scale powered model of the rotor systems research aircraft

A wind-tunnel investigation was conducted to determine the effects of the main-rotor wake on the aerodynamic characteristics of the rotor systems research aircraft (RSRA). For the investigation, a 1/6-scale model with a four-blade articulated main rotor was used. Tests were conducted with and without the main rotor. Both the helicopter and the compound helicopter were tested. The latter configuration included the auxiliary thrust engines and the variable-incidence wing. Data were obtained over ranges of angle of attack, angle of sideslip, and main-rotor collective pitch angle at several main-rotor advance ratios. Results are presented for the total loads on the airframe as well as the loads on the rotor, the wing, and the tail. The results indicated that without the effect of the rotor wake, the RSRA had static longitudinal and directional stability and positive effective dihedral. With the effect of the main rotor and its wake, the RSRA exhibited longitudinal instability but retained static directional stability and positive effective dihedral.

Mineck, R. E.↗
NASA NTRS1982

Simplified aeroelastic modeling of horizontal axis wind turbines

Certain aspects of the aeroelastic modeling and behavior of the horizontal axis wind turbine (HAWT) are examined. Two simple three degree of freedom models are described in this report, and tools are developed which allow other simple models to be derived. The first simple model developed is an equivalent hinge model to study the flap-lag-torsion aeroelastic stability of an isolated rotor blade. The model includes nonlinear effects, preconing, and noncoincident elastic axis, center of gravity, and aerodynamic center. A stability study is presented which examines the influence of key parameters on aeroelastic stability. Next, two general tools are developed to study the aeroelastic stability and response of a teetering rotor coupled to a flexible tower. The first of these tools is an aeroelastic model of a two-bladed rotor on a general flexible support. The second general tool is a harmonic balance solution method for the resulting second order system with periodic coefficients. The second simple model developed is a rotor-tower model which serves to demonstrate the general tools. This model includes nacelle yawing, nacelle pitching, and rotor teetering. Transient response time histories are calculated and compared to a similar model in the literature. Agreement between the two is very good, especially considering how few harmonics are used. Finally, a stability study is presented which examines the effects of support stiffness and damping, inflow angle, and preconing.

Wendell, J. H.↗
NASA NTRS1976

An experimental investigation of the flap-lag stability of a hingeless rotor with comparable levels of hub and blade stiffness in hovering flight

An experimental investigation of the flap-lag stability of a hingeless rotor in hovering flight is presented and discussed. The rotor blade and hub configuration were selected such that the hub and blade had comparable levels of bending stiffness. Experimental measurements of the lag damping were made for various values of rotor rotational speed and blade pitch angle. Specifically at a blade pitch angle of 8 deg at three-quarters radius, the lag damping was determined over a range of rotational speeds from 200 RPM to 320 RPM and also over a range of blade pitch angles from 0 deg to 8 deg.

Curtiss, H. C., Jr.↗
NASA NTRS1993

Effect of fluid compressibility on journal bearing performance

An analysis was undertaken to determine the effect of fluid film compressibility on the performance of fluid film bearings. A new version of the Reynolds equation was developed, using a polytropic expansion, for both steady-state and dynamic conditions. Polytropic exponents from 1 (isothermal) to 1000 (approaching an incompressible liquid) were evaluated for two bearing numbers, selected from a range of practical interest for cryogenic application, and without cavitation. Bearing loads were insensitive to fluid compressibility for low bearing numbers, as was expected. The effect of compressibility on attitude angle was significant, even when the bearing number was low. A small amount of fluid compressibility was enough to obtain stable running conditions. Incompressible liquid lacked stability at all conditions. Fluid compressibility can be used to control the bearing dynamic coefficients, thereby influencing the dynamic behavior of the rotor-bearing system.

Dimofte, Florin↗