Search NASA⌕ Search

SEARCH · Search NASA

Results for “route extensions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Experimental Evaluation of CTAS/FMS Integration in TRACON Airspace

A CTAS/FMS integration project at Ames Research Center addresses extensions to the CTAS air traffic management concept, among them the introduction of arrival routes specially designed for the use with a Flight Management System. These FMS arrival routes shall allow for the use of the INS' lateral and vertical navigation capabilities throughout the arrival until final approach. For the use in this project CTAS controller support tools that compliment the concept have been created. These tools offer controllers access to CTAS' prediction and planning capabilities in terms of speed and route advisories. The objective is to allow for a more strategic way of controlling aircraft. Expected benefits are an increase in arrival rate and a reduction of average travel times through TRACER airspace. A real time simulation is being conducted at Ames to investigate how FMS arrivals and approach transitions - with and without the support of CTAS tools - effect the flow of arriving traffic within TRACER airspace and the controllers' task performance. Four conditions will be investigated and compared to today's technique of controlling traffic with tactical vectoring: 1. FMS arrivals and approach transitions are available for controllers to issue to equipped aircraft - traffic permitting; 2. Speed advisories that match CTAS' runway balancing and sequencing plan are displayed to Feeder controllers; 3. Approach transition advisories (e.g., location of the base turn point) are displayed to Final controllers for tactical clearances ("Turn base now"); and 4. Approach transition advisories (voice and data link) are generated by CTAS and displayed to final controllers for strategic voice clearances ("Turn base five miles after waypoint xyz") or prepared in terms of a trajectory description for strategic data link clearance. Scenarios used in the study will represent current traffic and vary in density of arriving traffic and the kind and mix of equipage of arriving aircraft. Data will be collected from experiment runs with active TRACON controllers on the final approach spacing, the aircraft's speed profiles, the controllers interaction with CTAS tools, and number and timing of pilot controllers communications under the described conditions.

Romahn, Stephen↗
NASA NTRS2012

A Concept for Airborne Precision Spacing for Dependent Parallel Approaches

The Airborne Precision Spacing concept of operations has been previously developed to support the precise delivery of aircraft landing successively on the same runway. The high-precision and consistent delivery of inter-aircraft spacing allows for increased runway throughput and the use of energy-efficient arrivals routes such as Continuous Descent Arrivals and Optimized Profile Descents. This paper describes an extension to the Airborne Precision Spacing concept to enable dependent parallel approach operations where the spacing aircraft must manage their in-trail spacing from a leading aircraft on approach to the same runway and spacing from an aircraft on approach to a parallel runway. Functionality for supporting automation is discussed as well as procedures for pilots and controllers. An analysis is performed to identify the required information and a new ADS-B report is proposed to support these information needs. Finally, several scenarios are described in detail.

Barmore, Bryan E.↗
DOE OSTI2023

Highly Nonstoichiometric YAG Ceramics with Modified Luminescence Properties

Abstract Y 3 Al 5 O 12 (YAG) is a widely used phosphor host. Its optical properties are controlled by chemical substitution at its YO 8 or AlO 6 /AlO 4 sublattices, with emission wavelengths defined by rare‐earth and transition‐metal dopants that have been explored extensively. Nonstoichiometric compositions Y 3+x Al 5‐x O 12 ( x ≠ 0) may offer a route to new emission wavelengths by distributing dopants over two or more sublattices simultaneously, producing new local coordination environments for the activator ions. However, YAG typically behaves as a line phase, and such compositions are therefore challenging to synthesize. Here, a series of highly nonstoichiometric Y 3+x Al 5‐x O 12 with 0 ≤ x ≤ 0.40 is reported, corresponding to ≤20% of the AlO 6 sublattice substituted by Y 3+ , synthesized by advanced melt‐quenching techniques. This impacts the up‐conversion luminescence of Yb 3+ /Er 3+ ‐doped systems, whose yellow‐green emission differs from the red‐orange emission of their stoichiometric counterparts. In contrast, the YAG:Ce 3+ system has a different structural response to nonstoichiometry and its down‐conversion emission is only weakly affected. Analogous highly nonstoichiometric systems should be obtainable for a range of garnet materials, demonstrated here by the synthesis of Gd 3.2 Al 4.8 O 12 and Gd 3.2 Ga 4.8 O 12 . This opens pathways to property tuning by control of host stoichiometry, and the prospect of improved performance or new applications for garnet‐type materials.

Chemistry↗
NASA NTRS2015

Robonaut 2 - Building a Robot on the International Space Station

In 2010, the Robonaut Project embarked on a multi‐phase mission to perform technology demonstrations on‐board the International Space Station (ISS), showcasing state of the art robotics technologies through the use of Robonaut 2 (R2). This phased approach implements a strategy that allows for the use of ISS as a test bed during early development to both demonstrate capability and test technology while still making advancements in the earth based laboratories for future testing and operations in space. While R2 was performing experimental trials onboard the ISS during the first phase, engineers were actively designing for Phase 2, Intra‐Vehicular Activity (IVA) Mobility, that utilizes a set of zero‐g climbing legs outfitted with grippers to grasp handrails and seat tracks. In addition to affixing the new climbing legs to the existing R2 torso, it became clear that upgrades to the torso to both physically accommodate the climbing legs and to expand processing power and capabilities of the robot were required. In addition to these upgrades, a new safety architecture was also implemented in order to account for the expanded capabilities of the robot. The IVA climbing legs not only needed to attach structurally to the R2 torso on ISS, but also required power and data connections that did not exist in the upper body. The climbing legs were outfitted with a blind mate adapter and coarse alignment guides for easy installation, but the upper body required extensive rewiring to accommodate the power and data connections. This was achieved by mounting a custom adapter plate to the torso and routing the additional wiring through the waist joint to connect to the new set of processors. In addition to the power and data channels, the integrated unit also required updated electronics boards, additional sensors and updated processors to accommodate a new operating system, software platform, and custom control system. In order to perform the unprecedented task of building a robot in space, extensive practice sessions and meticulous procedures were required. Since crew training time is at a premium, the R2 team took a skills‐based training approach to ensure the astronauts were proficient with a basic skill set while refining the detailed procedures over several practice sessions and simulations. In addition to the crew activities, meticulous ground procedures were required in order to upgrade firmware on the upper body motor drivers. The new firmware for the IVA mobility unit needed to be deployed using the old software system. This also provided an opportunity to upgrade the upper body joints with new software and allowed for limited insight into the success of the updates. Complete verification that the updated firmware was successfully loaded was not confirmed until the rewiring of the upper body torso was complete.

Diftler, Myron↗
DOE OSTI2023

Modular Functionalization of Metal‐Organic Frameworks for Nitrogen Recovery from Fresh Urine**

Abstract Nitrogen recovery from wastewater represents a sustainable route to recycle reactive nitrogen (Nr). It can reduce the demand of producing Nr from the energy‐extensive Haber‐Bosch process and lower the risk of causing eutrophication simultaneously. In this aspect, source‐separated fresh urine is an ideal source for nitrogen recovery given its ubiquity and high nitrogen contents. However, current techniques for nitrogen recovery from fresh urine require high energy input and are of low efficiencies because the recovery target, urea, is a challenge to separate. In this work, we developed a novel fresh urine nitrogen recovery treatment process based on modular functionalized metal–organic frameworks (MOFs). Specifically, we employed three distinct modification methods to MOF‐808 and developed robust functional materials for urea hydrolysis, ammonium adsorption, and ammonia monitoring. By integrating these functional materials into our newly developed nitrogen recovery treatment process, we achieved an average of 75 % total nitrogen reduction and 45 % nitrogen recovery with a 30‐minute treatment of synthetic fresh urine. The nitrogen recovery process developed in this work can serve as a sustainable and efficient nutrient management that is suitable for decentralized wastewater treatment. This work also provides a new perspective of implementing versatile advanced materials for water and wastewater treatment.

Guo, Lei↗
DOE OSTI2025

Accurate and Efficient Prediction of p K w in Aqueous Electrolytes Using Local Electrostatic Potentials

The K w =10 -pK w in aqueous electrolytes exhibit significant variations as a function of ion concentration. This behavior is not well-described by the Pitzer model, particularly at high concentrations. Here, we provide a molecular interpretation of the concentration dependent trends in p K w and develop a new method that accurately predicts the dissociation constant based upon the local electrostatic potential of the water oxygen that is determined by its nearest neighbors. The method is computationally efficient, relying only upon sampling of the local configurations (via molecular dynamics) and a small set of experimentally measured p K w . It is extensible to a range of salt compositions and the molecular understanding of the local potentials provides new routes toward the development of electrolytes with tailored physicochemical properties like p K w .

anions↗
DOE OSTI2020

Magnetic domain engineering in SrRuO3 thin films

Abstract Magnetic domain engineering in ferromagnetic thin films is a very important route toward the rational design of spintronics and memory devices. Although the magnetic domain formation has been extensively studied, artificial control of magnetic domain remains challenging. Here, we present the control of magnetic domain formation in paradigmatic SrRuO 3 /SrTiO 3 heterostructures via structural domain engineering. The formation of structural twin domains in SrRuO 3 films can be well controlled by breaking the SrTiO 3 substrate symmetry through engineering miscut direction. The combination of x-ray diffraction analysis of structural twin domains and magnetic imaging of reversal process demonstrates a one-to-one correspondence between structural domains and magnetic domains, which results in multi-step magnetization switching and anomalous Hall effect in films with twin domains. Our work sheds light on the control of the magnetic domain formation via structural domain engineering, which will pave a path toward desired properties and devices applications.

Materials Science↗
DOE OSTI2023

Modular Functionalization of Metal‐Organic Frameworks for Nitrogen Recovery from Fresh Urine

Nitrogen recovery from wastewater represents a sustainable route to recycle reactive nitrogen (Nr). It can reduce the demand of producing Nr from the energy-extensive Haber-Bosch process and lower the risk of causing eutrophication simultaneously. In this aspect, source-separated fresh urine is an ideal source for nitrogen recovery given its ubiquity and high nitrogen contents. However, current techniques for nitrogen recovery from fresh urine require high energy input and are of low efficiencies because the recovery target, urea, is a challenge to separate. In this work, we developed a novel fresh urine nitrogen recovery treatment process based on modular functionalized metal–organic frameworks (MOFs). Specifically, we employed three distinct modification methods to MOF-808 and developed robust functional materials for urea hydrolysis, ammonium adsorption, and ammonia monitoring. By integrating these functional materials into our newly developed nitrogen recovery treatment process, we achieved an average of 75 % total nitrogen reduction and 45 % nitrogen recovery with a 30-minute treatment of synthetic fresh urine. The nitrogen recovery process developed in this work can serve as a sustainable and efficient nutrient management that is suitable for decentralized wastewater treatment. This work also provides a new perspective of implementing versatile advanced materials for water and wastewater treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

MoRE-Brain: Routed Mixture of Experts for Interpretable and Generalizable Cross-Subject fMRI Visual Decoding

Decoding visual experiences from fMRI offers a powerful avenue to understand human perception and develop advanced brain-computer interfaces. However, current progress often prioritizes maximizing reconstruction fidelity while overlooking interpretability, an essential aspect for deriving neuroscientific insight. To address this gap, we propose MoRE-Brain, a neuro-inspired framework designed for high-fidelity, adaptable, and interpretable visual reconstruction. MoRE-Brain uniquely employs a hierarchical Mixture-of-Experts architecture where distinct experts process fMRI signals from functionally related voxel groups, mimicking specialized brain networks. The experts are first trained to encode fMRI into the frozen CLIP space. A finetuned diffusion model then synthesizes images, guided by expert outputs through a novel dual-stage routing mechanism that dynamically weighs expert contributions across the diffusion process. MoRE-Brain offers three main advancements: First, it introduces a novel Mixture-of-Experts architecture grounded in brain network principles for neuro-decoding. Second, it achieves efficient cross-subject generalization by sharing core expert networks while adapting only subject-specific routers. Third, it provides enhanced mechanistic insight, as the explicit routing reveals precisely how different modeled brain regions shape the semantic and spatial attributes of the reconstructed image. Extensive experiments validate MoRE-Brain’s high reconstruction fidelity, with bottleneck analyses further demonstrating its effective utilization of fMRI signals, distinguishing genuine neural decoding from over-reliance on generative priors. Consequently, MoRE-Brain marks a substantial advance towards more generalizable and interpretable fMRI-based visual decoding.

Wei, Yuxiang [Georgia Institute of Technology]↗
DOE OSTI2019

Network coding for improving throughput in WDM optical networks with dedicated protection

Network coding (NC) has been recently emerging as an excellent technique for leveraging network efficiency. In optical networks, NC and protection appear to be a good match and indeed, NC could be effectively exploited for greater protection efficiency thanks to the opportunity of combining signals rather than duplication in the traditional approach. Motivated by this observation, we investigate the application of a simple and practical NC technique based on XOR operation to improve the network throughput in survivable optical networks. To this end, we propose the NC-based protection whose speed recovery is on a par with the conventional 1+1 dedicated protection while the capacity usage could be more efficient, paving the way for improving throughput in constrained capacity conditions. A novel mixed integer linear programming model is developed for survivable optical networks design employing the proposed NC-based protection. The model attempts to optimally determine the demands to serve, the routing for served demands and NC assignment among demands aiming at maximizing the network throughput in the constraint of bandwidth limitation. Extensive numerical evaluations on realistic topologies are provided to highlight the advantages of our NC-based protection proposal compared with the conventional dedicated protection in improving the network throughput. Encouraging results are observed when the new protection proposal based on NC could accommodate up to 30% more traffic than the conventional case.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1992

The VLBA correlator: Real-time in the distributed era

The correlator is the signal processing engine of the Very Long Baseline Array (VLBA). Radio signals are recorded on special wideband (128 Mb/s) digital recorders at the 10 telescopes, with sampling times controlled by hydrogen maser clocks. The magnetic tapes are shipped to the Array Operations Center in Socorro, New Mexico, where they are played back simultaneously into the correlator. Real-time software and firmware controls the playback drives to achieve synchronization, compute models of the wavefront delay, control the numerous modules of the correlator, and record FITS files of the fringe visibilities at the back-end of the correlator. In addition to the more than 3000 custom VLSI chips which handle the massive data flow of the signal processing, the correlator contains a total of more than 100 programmable computers, 8-, 16- and 32-bit CPUs. Code is downloaded into front-end CPU's dependent on operating mode. Low-level code is assembly language, high-level code is C running under a RT OS. We use VxWorks on Motorola MVME147 CPU's. Code development is on a complex of SPARC workstations connected to the RT CPU's by Ethernet. The overall management of the correlation process is dependent on a database management system. We use Ingres running on a Sparcstation-2. We transfer logging information from the database of the VLBA Monitor and Control System to our database using Ingres/NET. Job scripts are computed and are transferred to the real-time computers using NFS, and correlation job execution logs and status flow back by the route. Operator status and control displays use windows on workstations, interfaced to the real-time processes by network protocols. The extensive network protocol support provided by VxWorks is invaluable. The VLBA Correlator's dependence on network protocols is an example of the radical transformation of the real-time world over the past five years. Real-time is becoming more like conventional computing. Paradoxically, 'conventional' computing is also adopting practices from the real-time world: semaphores, shared memory, light-weight threads, and concurrency. This appears to be a convergence of thinking.

Wells, D. C.↗
DOE OSTI2021

Re-routing of Sugar Catabolism Provides a Better Insight Into Fungal Flexibility in Using Plant Biomass-Derived Monomers as Substrates

The filamentous ascomycete Aspergillus niger has received increasing interest as a cell factory, being able to efficiently degrade plant cell wall polysaccharides as well as having an extensive metabolism to convert the released monosaccharides into value added compounds. The pentoses D-xylose and L-arabinose are the most abundant monosaccharides in plant biomass after the hexose D-glucose, being major constituents of xylan, pectin and xyloglucan. In this study, the influence of selected pentose catabolic pathway (PCP) deletion strains on growth on plant biomass and re-routing of sugar catabolism was addressed to gain a better understanding of the flexibility of this fungus in using plant biomass-derived monomers. The transcriptome, metabolome and proteome response of three PCP mutant strains, Δ larA Δ xyrA Δ xyrB , Δ ladA Δ xdhA Δ sdhA and Δ xkiA , grown on wheat bran (WB) and sugar beet pulp (SBP), was evaluated. Our results showed that despite the absolute impact of these PCP mutations on pure pentose sugars, they are not as critical for growth of A. niger on more complex biomass substrates, such as WB and SBP. However, significant phenotypic variation was observed between the two biomass substrates, but also between the different PCP mutants. This shows that the high sugar heterogeneity of these substrates in combination with the high complexity and adaptability of the fungal sugar metabolism allow for activation of alternative strategies to support growth.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Decoupling electrode kinetics to elucidate reaction mechanisms in alkaline water electrolysis

Alkaline water electrolysis (AWE) presents key advantages, including reduced material costs, enhanced operational stability, and compatibility with non-precious metal catalysts, positioning it as a scalable route for hydrogen production. In this study, we introduce a minimally invasive single-cell configuration incorporating a reference electrode via diaphragm extension to form an internal ion channel. This setup, combined with an interfaced potentiostat and auxiliary electrometer, enables real-time, independent monitoring of anode and cathode behavior, offering high-resolution electrochemical diagnostics. While it is well established that the hydrogen evolution reaction (HER) exhibits sluggish kinetics in alkaline media, our study reveals that this limitation persists even in practical AWE systems where nickel-based substrates are used as electrodes. This observation is supported by both experimental data and voltage breakdown modeling. Arrhenius-type analysis reveals that localized electric fields induced by catalysts shift the reaction kinetics from classical Butler–Volmer behavior toward a Marcus-like regime, where interfacial molecular dynamics and bimolecular charge transfer dominate. We propose a semi-empirical model and a surficial reaction mechanism to describe these dynamics. This work underscores the critical need for cathode innovation and provides a rational framework for designing advanced catalysts and electrode architectures to optimize AWE performance.

08 HYDROGEN↗
DOE OSTI2025

Draft Prototype Microreactor Transportation Safety Program

Microreactors are compact reactors capable of producing less than 50 megawatts of electrical energy. Typically, these reactors are factory-fabricated and designed to be easily transportable by truck, rail, vessel, or air. Microreactor designs often assume that the unit can be transported containing either unirradiated or irradiated fuel. The interest in microreactors is driven by several factors, including the need to generate power on at remote locations, at military installations, at facilities such as data centers, and in areas recovering from natural disasters. The U.S. Department of Defense is actively pursuing the microreactor concept to meet the increasing energy demands of military operations that require portable and dense power sources. Commercial vendors are also exploring microreactor concepts. The report Microreactor Transportation Emergency Planning Challenges (Maheras et al. 2024) outlined the emergency planning challenges associated with the transportation of microreactors by road, rail, and by barge/ship. The successful commercial deployment and redeployment of microreactors will also require the development of microreactor transportation safety programs. The elements in these safety programs are not specific to microreactors; however, the transport of microreactors may pose unique challenges in these areas. This report builds on the report Microreactor Transportation Emergency Planning Challenges (Maheras et al. 2024) and develops the elements of a prototype microreactor transportation safety program that describes the elements that should be contained vendor-developed microreactor transportation safety programs, identifying the unique elements associated with microreactor transport. This will provide vendors and their transportation contractors a basis for their transportation planning and will accelerate the commercial deployment and redeployment of microreactors by identifying those issues unique to microreactor transport. The emphasis of this report is on highway transport of microreactors. This is based on a U.S. Nuclear Regulatory Commission transportation package approval strategy of crawl-walk-run, where transport by highway is evaluated first (Coles et al. 2021, 2024, Maheras et al. 2021), then other surface modes (rail and barge/ship), and finally air transport. Evaluation of maritime transport of microreactors was recently initiated (Rigato et al. 2024, Maheras et al. 2025). The report first discusses microreactors in general and microreactor transportation safety program planning assumptions. The report then provides a description of the transportation safety planning process and provides an extensive discussion of the elements of transportation safety programs. Specific elements examined included transportation roles and responsibilities, transportation planning, transportation mode and route selection, carrier selection, transportation packaging, advance notification of shipments, public information and communications, emergency response plans and procedures, inspections, security, safe parking, shipment tracking, weather and road conditions, medical preparedness, training and exercises, and program evaluation. The report then identifies the unique elements of a transportation safety program associated with microreactor transport. These unique elements were in the areas of: the unusual nature of microreactor designs, compensatory measures, increased radiation dose rates in the vicinity of microreactors, transportation package approval versus 10 CFR 50.59, and the use of a risk-informed transportation package approval process.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1976

Global measurements of gaseous and aerosol trace species in the upper troposphere and lower stratosphere from daily flights of 747 airliners

Extensive measurements include ozone, carbon monoxide, water vapor, and aerosol and condensation nuclei number density. Less extensive measurements include chlorofluoromethanes, sulfates and nitrates. Certain meteorological and flight information are also recorded at the time of these measurements. World routes range in latitude from about 60 deg N near North America to about 40 deg S over Australia and 23 deg S over South America. Typical data show significant changes in ozone, carbon monoxide, and water vapor when crossing the tropopause either during changes in altitude or at cruise altitude. These gases as well as light scattering particles and condensation nuclei exhibit considerable variability along a flight route.

Perkins, P. J.↗
DOE OSTI2024

Unraveling the Nature of Lasing Emission from Hybrid Silicon Nitride and Colloidal Nanocrystal Photonic Crystals with Low Refractive Index Contrast

Silicon nitride is used for its low optical loss and high thermal stability, making it a suitable platform for visible-light applications in integrated photonic devices. However, its application has been limited due to inefficient light emission, a problem addressed by integrating various types of light emitters onto the platform. In particular, the integration of solution-processable colloidal nanocrystals (NCs) as optical gain materials onto the silicon nitride platform is a promising route but requires a more solid theoretical footing. By leveraging 2D surface-emitting photonic crystal structures combined with NCs, we effectively confine and manipulate light to achieve lasing from green to red. Building on this, we model the light–matter interactions of the low index contrast NC/nitride platform, validated by extensive experimental validations through Fourier imaging techniques, revealing the full photonic band structure and showing clear mode congestion. Finally, these comprehensive studies confirm the potential of hybrid NC-based structures for fully integrated on-chip laser applications and indicate routes for further improvement.

BIC Lasing↗
DOE OSTI2026

Promotion of CaCO 3 Nucleation by Carboxyl- and Amine-Terminated Peptoid Nanotubes

The use of surfaces to promote heterogeneous nucleation of CaCO 3 has been extensively studied to better understand natural processes of biomineralization, to develop bioinspired approaches for synthesizing composite materials with diverse functionalities, and as a route toward accelerating CO 2 mineralization. Peptoids have emerged as a material of particular interest, because they offer tunable side chain chemistry while maintaining a constant long-range self-assembled architecture. Here, in this work, we investigate the ability of films of self-assembled -NH 2 and −COOH terminated peptoid nanotubes to promote the nucleation of CaCO 3 . Using a combination of atomic force, scanning electron, and optical microscopy, we find that interwoven films of nanotubes formed from peptoids with -NH 2 side chains promote the preferential formation of vaterite with the (001) plane parallel to the film and exhibit a lower interfacial energy than that reported for inorganic surfaces. In contrast, the film of −COOH-functionalized peptoid nanotubes is a much stronger promoter, giving a particle density 5 orders of magnitude larger than for the -NH 2 terminated peptoid nanotubes and enabling complete coverage of individual peptoid tubes with CaCO 3 nanoparticles that results in a composite material with a 50-fold increase in Young’s modulus. Thus, interwoven films of peptoid nanotubes provide a useful platform for investigating the impact of specific chemical groups on nucleation and offer potential application to accelerated mineralization of CO 2 for removal from the environment or modulation of mineralogy and properties of carbonate-based building materials.

carbon nanotubes↗
DOE OSTI2026

The role of focusing geometry in MeV x-ray production from petawatt laser–solid interaction

Relativistic laser–plasma interactions provide a compact and flexible route to generating bright, ultrashort pulses of MeV x rays, with applications in high-energy density science, nuclear physics, and radiography. Despite extensive study of intensity scaling in laser-driven electron acceleration, the role of focusing geometry and focal-volume effects in MeV radiation production remains insufficiently understood. Here, we present experimental and kinetic simulation results from the Texas Petawatt Laser (120 J, 140 fs) in which the focusing geometry (f/3 or f/1.5) is varied, while the laser energy and pulse duration are fixed. Experimentally, the f/3 geometry produces approximately three times more MeV radiation than the f/1.5 geometry, despite its twofold lower nominal vacuum intensity. This result is based on the time-integrated radiation per unit solid angle, as measured along the diagnostic line of sight. Three-dimensional particle-in-cell simulations reproduce this trend when a modest (10s of μm) effective focal plane shift is introduced, demonstrating that relativistic laser–plasma coupling is highly sensitive to focal geometry in the presence of a preplasma. This behavior is consistent with differences in interaction length and effective intensity at the critical surface between the two configurations. The sensitivity of the tightly focused f/1.5 configuration ($z_R ≈$⁠ 5 μ m) reflects the combined influence of thermal lensing and an extended preplasma, while the f/3 geometry (⁠$z_R ≈$ 80 μ m) remains comparatively robust. These results demonstrate a breakdown of conventional intensity scaling and identify focusing geometry as a critical control parameter for MeV electron and x-ray generation at petawatt powers. Implications for laser–plasma-based radiographic facilities are also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗